Help wit setting up caller display

Hi,
I have looked around to see if I can resolve this issue on my own, however I have drawn a blank.
My package includes BT home privacy with gives caller display free, however our BT Graphite phones, which are caller display compatable, do not show caller display on incomming calls, instead they just dispaly 'call 1' even if the number is in my phonebook.
Unfortunatly I think in need to set it up on the phones, however I have missed placed our handbook for the phone!! can any one either,
1) Tell me how to activate caller display
OR
2) Post a link to an on-line version of the hand book for BT Graphite Phones.
Thanks for your help
Mini_stella

mini_stella wrote:
Hi,
I have looked around to see if I can resolve this issue on my own, however I have drawn a blank.
My package includes BT home privacy with gives caller display free, however our BT Graphite phones, which are caller display compatable, do not show caller display on incomming calls, instead they just dispaly 'call 1' even if the number is in my phonebook.
Unfortunatly I think in need to set it up on the phones, however I have missed placed our handbook for the phone!! can any one either,
1) Tell me how to activate caller display
OR
2) Post a link to an on-line version of the hand book for BT Graphite Phones.
Thanks for your help
Mini_stella
Hi.
Which Graphite phone have you got ? There are a variety of different ones, so they may have different display options and methods of access.
http://www.andyweb.co.uk/shortcuts
http://www.andyweb.co.uk/pictures

Similar Messages

Help with setting up Caller-id on FXO in 2911 H.323 gateway.

I have a remote site that has a couple of POTS lines terminating to a FXO on the 2911. This remote site is an H.323 gateway in a CUCM 8.6 cluster. Incoming local calls for that location ring all phones at the location.
What do I need to do to enable Caller-id on these POTS lines terminating to the FXO? I am pretty sure the carrier is sending the caller ID information.
Thanks

Hi
1- Please find the below table as the following link http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
Caller ID
Requires VIC-2FXO-M1, VIC-2FXO-M2, VIC-4FXO-M1, VIC2-2FXO, VIC2-4FXO, or MRP3-8FXOM1
2- under fxo port
voice-port 0/3/0
caller-id enable
3-If the above configure and still have no caller id , please add the below commannds to the voice-port
caller-id alerting line-reversal
cptone ?              "based on your"
caller-id alerting ring 2    "the default is 1" maximum number of rings to be detected before a call is answered over an FXO voice port.
4-Do debus to make sure all ok
"debug vpm signal "
[0/3/0] get_fxo_caller_id:Caller ID received. Message type=128 length=31 checksum=74
Thank you
please rate all useful information

Caller Display

Hope some one can help. Have had caller display for some time, bought a new phone and it will not work. Reverted to old phone and caller display worked for a while and then stopped working. We have taken both phones to friends who have caller display and caller display worked on both old and new phone. Have tried #234# and it states caller identity will not be displayed. Also answer phone will not work on either phone but work at friends. Have removed ASDL filter and installed i-plate with no effect. Phone at times rings intermittently. Have reported fault and automatic system says there is no fault on the line. Any suggestions gratefully received.

#234# disables so it will not be displayed, dial *234# to enable it again.
Summary
CALLER DISPLAY may be switched on with the command *234#, you check it with *#234# and you switch it off with #234#.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

I have a PowerBook G4 17" and need Apple discs to set it up again. Mine lost during move. Screen seems damaged, has vertical lines. Can anyone help. I can call as I have unlimited calling on my iPhone 6 anywhere in North America.

I have a PowerBook G4 17" and need Apple discs to set it up again. Mine lost during move. Screen seems damaged, has vertical lines. Can anyone help. I can call as I have unlimited calling on my iPhone 6 anywhere in North America.

king,
If your Powerbook's serial number (do not post it here) starts with "W8" then the vertical lines are mostly likely due to a defect in the display itself. W8 is a factory code and, during the iMac G5 and PowerBook G4 timespan, that factory shipped thousands of units with the same defect. It cannot be fixed via software.
As all PowerBooks are now classed as "obsolete," an Apple Store will not work on it. They will look at it ands tell you it has vertical lines and that they cannot fix it. This Apple article shows Apple devices they curently considered obsolete:
Vintage and obsolete products - Apple Support
It is possible that some Apple Authorized Service Providers (AASP) will still work on older computes but they cannot get neededparts from Apple. As this issue was so pervassive, it wil be hard for you or an AASP to find a used/pulled display that is not effected with the "W8 Curse."
Although I love the old PowerBooks, I would not even spent the money for disks, much less the US$150-400 it would cost to replace the display, even should one be available.
If you give us a rough idea of where you are in the world, we can suggest repair shops specializing in fixing older Mac notebooks, but be aware those resources may be rather scare outside North America.

I took my iMac to be fixed and when i got it back, mail was not set up. I called Apple Support and they helped me set up mail. Then the emails went to trash on the iMac and on the MacBook Pro (same emails). There are no numbers by the 'inbox' to tell how

I took my iMac to be fixed and when I got it back, mail was not set, so I called Apple and they helped me set up mail. Now the new mail goes to trash and there is no number by the 'inbox' to tell me how many new messages I have. I cannot save a draft to 'drafts.' There is a large number by 'trash' (I think all mail went to trash - including drafts). When I send myself an emai, it goes to trash also. This is on both my iMac (the one taken in) and my MacBook Pro (same emails) which was not taken in.
I went to 'rules' but have no idea what to do there. There are no rules in the rule box. When I click 'add rule' it puts 'rule 1' in the rule box, but since that was not there when I took it in, I delete it to have an empty rule box.
Can someone pleasehelp me. I am completely stupid with all this. Do not under stand what is suppose to be set up in 'rules.'
Thank you so much,
Arudi

Now new mail is coming to both computer's inboxes but there is no number on the stamp icon on dock to show number of emails on the iMac. Nor is there a number by either email address under MAILBOXES/inbox (sidebar) on the iMac. This number is showing on MacBook Pro.
I also can save drafts now on both computers.
Seems the Pro is fixed and the iMac is only missing the numbers on dock icon and by addresses in inbox.
Now that the problem is less, I feel i am wasting your time but will continue so maybe I can get those numbers back.
Two emails > AT&T email and gmail.
Apple's Mail program for email - yes, and gmail.
IMAP for both accounts.
Did not change mail configuration on MacBook.
The iMac and MacBook Pro have the same mail configuration except in Accounts/mailbox behaviours/store draft messages on the server was not marked on MacBook > it is now.
'Store junk messages on the server' was marked on one computer for gmail, but is unmarked on both now.
On the iMac, Accounts/Accounts info/Outgoing mail for gmail is smtpgmail.
On the MacBook Pro for gmail it is smpt.gmail.com (plus) my email address.
Rules/Add rule window, on the MacBook third line is 'Any Recipient', on the iMac third line is 'From."
The last box on that line has my email address on the MacBook.
The last box on that line has the last address I sent an emil to (last night), on the iMac.
On the last line on iMac, no box was selicted for 'to mailbox' > I choose 'inbox' because it is on the MacBook Pro.
Now I have a Rule #1 and am not sure I should have because there was no rules marked when I took the computer in.
Thank you. I relized I had done the labeling wrong when so much of my question appeared twice and no one else's did. I know how to do it now.
Thank you so much,
Arudi

HT204023 I am not able to set my Personal Hotspot setting, if I try to set it massage displayed "To enable Personal Hotspot for this account, contact carrier " I am in Oman and using Nawras service for data plan. Plz help me

I am not able to set my Personal Hotspot setting, if I try to set it massage displayed "To enable Personal Hotspot for this account, contact carrier " I am in Oman and using Nawras service for data plan. Plz help me. Before I was using this service but now facing problem.

Md Asad wrote:
Yes but they told mobile co mean Device 'iPhone co'
Sorry but that makes no sense in English. Only your mobile phone company (i.e. "carrier") can enable the Personal Hotspot feature.

Caller display won't work since i've swooped to BT

I have a PANASONIC cordless trio phone set, caller display worked fine untill we swooped to BT Broardband and Phone package. I have checked the phone line without the filter still no display can anyone help.
Solved!
Go to Solution.

Hi Cobra,
It is possible the caller display facility hasn't followed you across from your previous service providor.
You can check this by dialling *#234# this will tell you if the service is active (caller identity will be displayed) or not (caller identity will not be displayed).
If not active try dialling *234# to activate, if the message says 'this service is not available' (or something along these lines) the the facitliy is not rented on your account and you will have to call BT to arrange or log on to BT.com to order through the net.
The fault teams on 0800800151 can order this or you can call the sales teams directly on 0800800150.
hope that clears it up for you :-)

Caller Display Problems

Hello, I recently rejoined BT for home telephone and broadband having been with talk talk and O2. I have had a bit of a mare with the Infinity and phone install but it is done now. I have contacted BT about caller display that was included with my package. They stated it would be active on Monday 27th Feb. It was not. Contacted them again and they said it would be active on 28th. It was not and again, I contacted them yesterday and despite assurances caller display is still not active.
I have done the *#234# test which says caller ID will be displayed. I have some rather expensive Gigaset SL78H digital handsets. Caller display worked with O2 and Talk Talk but it will not work with BT. Is this handset compatible with the caller display servie provided by BT? It worked with my previous phone line providers.
The phone is plugged into the master socket via a network. I have removed the ADSL filters as I was advised to do but to no avail. I am at my wits end now.
Thank You for any help.
Neil

I have just joined this forum out of sheer frustration at our Caller Display still not working after almost three weeks, numerous phone calls, online chats etc., from advisors insisting it would be up and running again in 12/24 hours or whatever. Yesterday, someone even said I should go and buy a new phone! to try out the equipment again before they send out an engineer. Bought a new phone, keyed in some numbers, got them to phone the land line and it still came up Unavailable. I even took a phone call from BT on the new phone so it proves that the new one works. All the phone calls I have had with BT advisors have been from people overseas I think, and I don't think they can grasp the fact that the Caller Privacy ID is still on i.e. our landline number does not come up on other people's phones and all our directory entries are listed in our phone and we can use them to dial out. Dialling out and receiving phone calls is still ok. They are now saying an engineer will have to come out but I know for a fact it is nothing to do with our phone itself. I don't want a bill of £130.00 if he finds nothing wrong with it. I am at the end of my tether.
All this would have been avoided I think if we still had BT shops in the local high street.
Any ideas anyone?

Caller display only works on some calls

I have a paragon 650 on a bt anytime call plan.
I have only one socket and only the telephone.
When the phone rings the number will only show on some occasions. If I do a 1471 the callers number is listed.
Some times the same callers number will list and on other occasions it does not.
I have put a paragon 500 on the line with the same results(this phone works perfectly OK on another bt anytime call plan line)
any ideas
thanks

If you report it to BT, they will investigate for you. It is most likely a faulty line card in the exchange.
Provided that you report it as a caller display problem, they will arrange for an engineer who has a caller display unit, to check the line in the exchange.
It could simply be that the line gain setting is too low, as the caller display does use a burst of signalling tones, just before the first ring is sent. If you are a long distance from the exchange, then this signal may be too weak.
If this burst is not received properly by your phone, then so number will be displayed.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Setting Enterprise Call Info Step Within An HTTP Triggered CRS Script

IPCC Enterprise 7.5(6)
CAD 7.5(6)
IPIVR 7.0(1)sr05_build504
We had a vendor develop some IVR & ICM scripts a few years back to take a website triggered request and pass along it’s value from the header, store it into Call Peripheral Variable 1 and place a call to a queue with agents (using CAD). It then sets off a work flow group macro to populate this value (from PV1) into another application along with a repeating message to the agent that says they have a new request. Since we recently upgraded our IVR to 7.0(1)sr05, I had to change the scripting some to make it work. They were using a freaky way of getting the value into PV1 using a pre-connect application triggered from the initial application. Anyway, their method would not work with the new version any longer so I needed to alter the scripts some.
The problem I’m having is that PV1 is being set after the Place Call step. This actually needs to be set before it reaches an agent in order to pass the value into CAD. Currently, I’ve been using some delay statements in the ICM script to give it time to get the value into PV1 but it’s not 100%. I get sporadic results.
Current script in test.
I’m looking to see if anyone can tell me a way to setup the Set Enterprise Call Info step before the Place Call step? Since this is HTTP triggered, I can’t use (Triggering Contact) and I haven’t been able to set a pseudo contact because debug tells me that the contact is null or because it’s not a call contact.

Hi Gabriel. Thanks for the reply.
The current method that's in place seems to work fine for me in test but when in production, I'm getting about a 60-70% success rate. As it comes into my ICM queuing script, I'm using another Run Ext Script node to execute a delay to give the Set Enterprise Call Info step from the first VRU script extra time to set it's value before reaching the ICM Queue To Skill Group node. I definitely notice better results when I did this but still not a 100%.
The reason I'm doing this is because of the notation that the help file discusses about the Set Enterprise Call Info step:
"Note In a Cisco Unified CCX system:
Beginning with CRS 4.0, this step should be placed script before the call gets connected to an agent. This means the step in the script should be placed before the Select Resource Step or in the Selected/Queued branch of the Select Resource step.
If call data is set after the call gets connected to the agent, it will not be displayed in Cisco Agent Desktop (CAD)."
So this is why I've been looking to see if this step can somehow be set before the Place Call step. I'm not that familiar with altering Sessions or Contacts but was hoping someone might know how to manipulate these in order to let me do this.
Thanks again.

Caller display ringtone query

I have a Paragon 650 BT phone. I recently had caller display set-up and all the calls that are in my phone book have a different ringtone to any other incoming calls. Is there a way to change the ringtone as this is both hideous and loud, I cannot find a way of changing the ringtone for these calls. Please help.

You can change ringtones. See p41 in the User Guide here: http://btsupport.custhelp.com/ci/fattach/get/1545644/1262875163/redirect/1/session/L2F2LzEvdGltZS8xM...
You can click the white star next to this message if you think it was helpful.

Caller display facility

My neighbour recently purchased a handsfree set which has the caller display facility and had the caller ID function activated on her phone and all went well for a few days then the phone stopped displaying caller ID.
She called BT who checked the line and found a fault which was repaired and caller ID functioned again but a day later the caller ID function stopped working again
Again she rang BT and was told their is no fault on the line and threatened the usual " we will charge you if an engineer calls and can find no fault, so to find out if her handset was the cause she asked me if I'd bring my handset to her house to see if caller ID worked on my phone plugged into her line which it did.
Based on this she took her handset back to the supplier who supplied her with a new replacement which when she plugged it in failed to show caller ID.
She then bought the handset to my house and plugged it into my line and caller ID worked OK.
This is totally baffling when you consider my handset's caller ID works fine on my line and hers but her's only works on my line!
Both our handsets are Motorola and are models produced in the last year, so are technically up todate with high spec facilities.
We both use the primary BT sockets in our respective homes and have no filters in use or computers or wifi equipment near the base handsets.
She's also confirmed caller ID is activated on her line by dialling *#246#.
As I said, totally baffling and was hoping someone might have an idea that we haven't already tried or thought of ourselves.

What is the Model number of the phone? maybe its a known issue with that specific phone.
As you have said you have shown Caller ID is active on the line, so doesn't seem a BT issue.
Check your exchange or major service outagesIf someone has given a helpful answer, please click on their Ratings star on the left-hand side. ***

Different caller display !!

Does anyone know why there are two different types of answer screens. for instance i have had some calls display a small picture or blank cutout of the caller on the screen. Or others display a full picture on the screen with DECLINE or ANSWER at the bottom of the screen. I have looked at the contacts and I cannot seem anything different about them. Is there some setting which enables the whole screen picture or small picture.
Thanks in advance.

Hi. Thanks for the explanation. Unfortunately, I assigned all of my contacts via my iPhone once upon a time. Now that I've upgraded to iOS4, it seems that I'm experiencing the same problem that the person above described. Is this because my computer has now synced with my phone and perhaps it got the information about which photos should show for whom based on the computer - even though as I said it was all originally done on my phone. What a pain to have to go back and reset them all again. I hate the little thumbnail... I want the full photo back! Help!!

Pearl 8130 Call Display

Hello.
I can't seem to get call display to work on the phone. Everytime someone calls, it says unknown number. Even if I have the person in my address book. I tried doing what the FAQ said to do but it still didn't work. Maybe I did something wrong. Can someone help please? Thank you!

Greetings, and welcome to the BlackBerry.com Support Forums.
There could be any one of three solutions... Try these:
1. Make sure you set your own country code at Phone Dialer Screen > Options > Smart dialing.
Set your country code in this format: "+xx" where xx = your country code. Some countries have two or three digit Country Codes. Do not place the '+' in your contact's entry.
* In the US, set this Country Code as "+1", and place your loca area code in the proper box (this normally the default setting in a new BB).
2. At the same location, change the National Number Length to the number of digits for your country (since some countries will have less than 10 as set as the default in the BB). Find out the total digits, minus the country code. Do not place the '+' in your contact's entry.
* For example, some countries have a total number to 8 (plus 3 for country code). You would enter "8".
3. You may have "Content Protection" set on your Address Book.
Look at Options > Security > General Settings. Scroll down to Content Protection > Include Address Book = NO.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Synergy 6500 Caller Display intermittent

Hello,
I have a Synergy 6500 Quad. The problem is that caller display is intermittent, and fails to display incoming number or stored name about one in four calls. This is the second 6500 set that has the same problem (the first Quad set was replaced for a quite different reason). Have checked line, filter etc. and all OK. My old Synergy 4100 works perfectly on this line, as does a Panasonic phone which I borrowed.
Has anyone else had similar experience?
Thanks in anticipation

There are a number of things that can stop caller display functioning correctly. The ADSL filter. Sky box. Home hub and or any ADSL router.
All I can suggest is to isolate each poss bit of kit one we a time as a process of elimination.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

Help wit setting up caller display

Similar Messages

Maybe you are looking for