How do I fix my iPad if it won't upgrade to iOS 5? I have iTunes on here and every thing else I need what do I do?
How do I fix my iPad if it won't upgrade to iOS 5? I have iTunes on here and every thing else I need what do I do?
The option to update without the computer (Over the air) was made available with iOS 5. If your iDevice is using a version of iOS lower than 5, you will need to use iTunes on your syncing computer to perform the upgrade. Use the Apple link below as a guide for the upgrade.
http://support.apple.com/kb/HT4972
Also read the instructions from the section entitled "Update your device using iTunes" at the link below.
http://support.apple.com/kb/HT4623
Information regarding transferring purchases from your iDevice to iTunes on your syncing computer can be found at the link below.
http://support.apple.com/kb/ht1848
Similar Messages
-
I have iTunes 10.4 and every time I open it my CPU usage hits 100%. How do I stop this?
I have iTunes 10.4 and every time I open it my CPU usage hits 100%. This makes my computer really slow and almost unusable. How do I stop this? Another effect is that I cannot log onto the iTunes Store. I click on it and it says it is loading the iTunes store but the window remains blank.
So do I!
-
How can i fix my ipad mini? because it keeps on restarting repeatedly.
how can i fix my ipad mini? because it keeps on restarting repeatedly.
Ideally the best thing to do in this situation is a soft reset, press and hold down the Sleep/Wake and Home buttons together until the Apple logo appears.
The factory settings option you've gone for should resolve this as well, but unless you've backed up you will lose content with this option.
Regards,
Steve -
How do I fix a ipad that is "disabled"? When we connect to itunes it requests a password that must be typed into the ipad - which we can't do because it is locked.
If You Are Locked Out Or Have Forgotten Your Passcode
iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
iOS- Understanding passcodes
A Complete Guide to Recover Your iDevice if You Forget Your Passcode
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
1. Verify that you are using the latest version of iTunes before attempting to update.
2. Connect your device to your computer.
3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
4. Select the Summary tab.
5. Select the Restore option.
6. When prompted to back up your settings before restoring, select the Back Up
option (see in the image below). If you have just backed up the device, it is not
necessary to create another.
7. Select the Restore option when iTunes prompts you (as long as you've backed up,
you should not have to worry about restoring your iOS device).
8. When the restore process has completed, the device restarts and displays the Apple
logo while starting up:
After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
iOS, keep your device connected until the "Connect to iTunes" screen goes away or
you see "iPhone is activated."
9. The final step is to restore your device from a previous backup.
If you can not restore your device then you will need to go to recovery mode.
Placing your device into recovery mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
red slider appears, then slide the slider. Wait for the device to turn off.
If you cannot turn off the device using the slider, press and hold the Sleep/Wake
and Home buttons at the same time. When the device turns off, release the Sleep/Wake
and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the device.
The device should turn on. Note: If you see the screen pictured below, let the device
charge for at least ten minutes to ensure that the battery has some charge, and then
start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
When this screen appears you can release the Home button.
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information. -
How I can fix my iPad smart case ?
How I can fix my iPad smart case ?
If you close your smart case it's have to get log off but mine it doesn't work it's mean when I close mine it doesn't get off automatically !
-
How do I fix my iPad screen rotation since the iOS 7 upgrade?
How do I fix my iPad screen rotation since the iOS 7 upgrade?
Since the upgrade, my screen orientation does not change based on the iPad's current position. It is often upside-down?
Anyone else have a similar issue? If no, how did you fix it?
Thanks, JenniferUnderstanding the Side Switch
http://support.apple.com/kb/ht4085 -
How much to fix cracked iPad 4 screen
How much to fix cracked iPad 4 screen
Apple's Limited Warranty http://www.apple.com/legal/warranty/ for iPad excludes coverage for damage resulting from accident, disassembly, unauthorized service and unauthorized modifications.
Out-of-Warranty Service
If you own an iPad that is ineligible for warranty service but is eligible for Out-of-Warranty (OOW) Service, Apple will replace (Apple doesn't repair) your iPad with an iPad that is new or equivalent to new in both performance and reliability for the Out-of-Warranty Service fee listed below. (The replacement will most likely be a refurbished iPad in a brown box, however, it has a new screen, back and battery.)
iPad model
Out-of-Warranty Service Fee
iPad mini
$219
iPad 3rd, 4th generation
$299
iPad 2, iPad
$249
A $6.95 shipping fee will be added if service is arranged through Apple and requires shipping. All fees are in US dollars and are subject to local tax.
Certain damage is ineligible for out-of-warranty service, including catastrophic damage, such as the device separating into multiple pieces, and inoperability caused by unauthorized modifications. However, an iPad that has failed due to contact with liquid may be eligible for out-of-warranty service. See http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipad
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/
You may can get the iPad repaired at 3rd party repair sources for less $, however, any remaining Apple warranty will be voided.
iCracked - Broken iPhone, iPod or iPad
http://www.icracked.com/
iReVamp Electronics Screen Repair ($99)
http://www.irevampelectronics.com/ipad-2-broken-glass-screen-repair.html
iPad Repair & Screen Replacement Services
http://www.ifixyouri.com/16-ipad-repairs
RepairZoom iPad Repair
http://www.repairzoom.com/ipad-repair.html
Mission Repair
http://www.missionrepair.com/Apple_iPad_Repair_Services_s/431.htm
iGadgetResQ
http://www.igadgetresq.com/ipad-repair/
Cheers, Tom -
How do i fix my printer when it won't show the print preview for web pages? it worked and now not.
how do i fix my printer when it won't show the print preview for web pages? it worked for a while and now it doesn't. printer is an hp officejet 7310 all-in-one.
I would suspect this is a hardware issue. The rollers are probably having issues picking up the relatively smooth thick media. You might have better results be cleaning the paper pickup rollers with a damp paper towel. Also make sure the paper is snugly loaded and the paper guides have been correctly positioned.
Regards,
Bob Headrick, MS MVP Printing/Imaging
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V -
How do I fix the 4900 error I get when trying to burn a cd in itunes?
how do I fix the 4900 error I get when trying to burn a cd in itunes?
We are having the same issue.
Windows 7 x64
Microsoft Office 2013 (Word)
Adobe Reader XI (11.0.0)
Whenever someone tries to embed a PDF file into a Word document, the following error occurs:
The program used to create this object is AcroExch. That program is either not installed on your computer or it is not responding. To edit this object, install AcroExch or ensure that any dialog boxes in AcroExch are closed.
I have looked at alot of articles online that say to 'Disable' Protected Mode. This does not resolve the issue. This option is not set by default in our environment.
Do we have any confirmation or information from Adobe on this issue? -
How do I fix the compatibility issue between my iPhone 4S with iOS 7 and my Pioneer car stereo? There was no problem with iOS 6, but now I get a message saying "this device is not compatible" and so I can't use Netflix for example. How do I fix it?
This is a typical response from the manufacturer. Did you try the fix that Lawrence mentioned. When Apple or any other phone manufacturer update phone software, they have the latest Bluetooth installed. It is usually the problem with the radio manufacturer that they devices are using the older Bluetooth protocols. You can try this support document http://support.apple.com/kb/TS3581 and see if anything there helps, but generally it requires the radio manufacturer to update their firmware.
-
how can i fix this accessory is not optimized for this iphone you may experience noise caused bycellular interference and a decrease in cellular single strenght error in my new iphone4
Hello abyjohn,
I would be concerned too if the speaker on my iPhone was not working, and if I was getting a message about the accessory not being optimized. I found an article with some steps to take when you are experiencing issues like this.
iPhone: Can't hear through the receiver or speaker
http://support.apple.com/kb/TS1630
Thank you for using Apple Support Communities.
Best,
Sheila M. -
How do I fix it when an album won't play on my ipod but will in itunes?
How do I fix it when an album won't play on my ipod but eill in itunes?
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync all music and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
IPad 2 Wifi Problems after upgrading to iOS 6
I Updated my iPad 2 to ios6 then day iOS6 was released, ever since then i have been unable to connect to the wifi. I've reset the network setting and the wifi works for about 5 minutes until i go on any apple app ( itunes, app store, maps etc). I've reset the Network settings more than once, I've turned the HTTP proxy to auto, I've pressed Renew Lease, I've unplugged the wifi, and I've pressed Forget this network. Reluctantley i updated my ipod touch 4 gen to see if iOS 6 was the problem and I now have the exact same problem on my ipod touch. Someone Help!!
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting
http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet
http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Help......every few mins my wifi disconnects AND i rec the black display with the apple.... Any ideas to resolve? I am connected to secured home internet and have not connected to cellular svc.
Try #5.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I am trying to use siri, Siri keeps saying( SORRY SOMETHINGS GONE WRONG CAN YOU TRY AGAIN)
I HAVE TRIED SEVERAL NAMES AND NUMBERS IN MY CONTACTS.
What am I doing wrong or how can I correct it.Siri Fix
Turn OFF Siri
Reset Network Settings
Turn ON Siri
Done
Steps:
Tap Settings App>General>Siri>Turn OFF
General>Reset, near bottom>Reset Network Settings
Tap Settings App>General>Siri>Turn ON
Done
Maybe you are looking for
-
Error while starting Essbase Server
Hi, I installed essbase analytic server version 9.2.0. When I starting the server it is giving the following error: "essbase.exe - Entry Point Not Found The procedure entry point eSSWrite could not be located in the dynamic link library ESSAPINU.dll"
-
I logged on to the Adobe site, but there is apparently no record of my purchase. What do I do now?
-
Scheduling the ibots to multiple receipinets by mail
Hi, I have created a sample ibot.. I want to send this ibot to multiple receipients by email. where can I specify the email address of all the recipents. Thanks Edited by: user10441472 on Jan 17, 2010 12:00 PM
-
These are the logs External Users/Domains: [email protected], [email protected] Internal Users/Domains: [email protected], [email protected], [email protected] These are hosted on iplanet... Alternate Conversion channel approach is used as per Chad's
-
Where to download Upgrade Package
Hi All, I am looking for the downloading of upgrade package for Db upgrade to 8.8. Can any body help me out. I cannot find it. I have CD of 8.8 but this package is not there.. Regards, Waqas