How to Backup configuration using tftp/ftp in Prime LMS?
Hi
how can i backup ASA/PIX configuration using tftp/ftp in Prime LMS 4.2.2?
--I discovered those devices and can managed them in the LMS but in the config file backup the passwords are encrypted,
that's why i want to backup them with tftp/ftp.
thanks
Wrong service names are set in tnsnames.ora
Similar Messages
-
How can I browse the tftp/ftp directory on Cisco PI 2.0?
Hi All,
I just installed Cisco PI 2.0 on a virtual appliance and I'd like to browse the tftp/ftp directory. I ssh'ed in but couldn't figure out how. With WCS running on Windows, I can easily browse those folders. Please let me know how I can browse the tftp/ftp directory on Cisco PI 2.0 to check what files are in there.
Thank you.
RobertHi Robert,
To configure tftp\ftp:
go to Configure > TFTP/FTP Servers > Add TFTP/FTP Server
To access it :
The easiest way to configure a remote FTP server would be with the steps
below:
1) Access your server via CLI and access the configuration mode:
ncs/admin# conf t
Enter configuration commands, one per line. End with CNTL/Z.
ncs/admin(config)#
2) Create an FTP repository with the commands below:
ncs/admin(config)# repository localFTP
ncs/admin(config-Repository)#
3) Setup the username, password and server address:
ncs/admin(config-Repository)# url ftp://1.1.1.1
ncs/admin(config-Repository)# user ftpAdmin password plain 12345678
ncs/admin(config-Repository)# exit
ncs/admin(config)# exit
4) Save the NCS configuration:
ncs/admin# wr mem
The use of a different partition is not officially supported as only
folders under the /localdisk partition can be read by the application.
The only supported server types include TFTP, FTP, SFTP, NFS.
TFTP\ftp contains PI backups \database backup , configbackups etc..
Thanks-
Afroz
***Ratings Encourages Contributors *** -
This just to share the below post with windows users..
How to install/Configure/Use VT to detect Malware/Unwanted programs in Windows?
http://www.windowstechinfo.com/2014/03/how-to-installconfigureuse-vt-to-detect_29.html
Hetti Arachchige V Aravinda | Network & System Administrator (B.Sc, Microsoft Small Business Specialist, MCP, MCTS, MCSA, MCSE,MCITP, CCNA, CEH, MBCS)That is interesting. Normally a bootmgr error message means that the boot loader is corrupt and hard disk not "dead".. Replacing the hard drive is a quickie shotgun method of resolving the issue.
Did you give up on the SSD?
The desktop ( w/ASUS Crossfire V Formula-Z mobo) I am using to type this, has the same SSD that you asked about. I used the method I described in the earlier post to clone the OS to the SSD. The SSD is the boot drive.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer -
How incremental backup is used in recovery
Hi,
how incremental backup is used in recovery let's say i took full backup on sunday then monday tuesday, wednesday took incremental backup. now on wednesday DB crash. so how incremental backup will use in recovery as i understand DB will restore from full backup then archive and increment backup will apply for recovery?
please correct me if i am wrong.1) Backup FULL RMAN Level 0 - Sunday
2) Backup FULL RMAN LEVEL 1 (incremental) - other days
3) Backup Archives
Restore Level0 + Restore Level1 + Apliying Archives and recover database; -
How to backup database using sql query?
Hello,i'm student, i'm researching oracle database,i want to backup database that using sql query (like backup query in SQL SERVER) ,how to do that ??
Thank!No, database backups cannot be done from within the database.
Commands for backups are outside of the database.
See the "2 Day DBA Guide" http://download.oracle.com/docs/cd/E11882_01/server.112/e10897/toc.htm
and the "Backup and Recovery Users's (actually Adminsitrator's) Guide : http://download.oracle.com/docs/cd/E11882_01/backup.112/e10642/toc.htm
Hemant K Chitale -
How to backup configuration for a domain?
While I am learning WebLogic Server, I created serveral domains for excersice.
However, my laptop is now crashed and need to reinstall the whole system. So HOW
should I do to backup all the domains? If it's impossible, it means I have to
re-create all the domains again. I believe there must be a backup way. What's
that?Jonathan wrote:
While I am learning WebLogic Server, I created serveral domains for excersice.
However, my laptop is now crashed and need to reinstall the whole system. So HOW
should I do to backup all the domains? If it's impossible, it means I have to
re-create all the domains again. I believe there must be a backup way. What's
that?You can just zip/tar up all the domain directories.
Alternatively you could use the fantastic wlshell utility
(www.wlshell.com) to generate a script to recreate your domain (it can
generate a script automatically from your config.xml). That has the
advantage that you can use it to build domains on different machines
very easily, customising where necessary.
Robert -
How to backup database using RMAN on another server's tape?
Dear All,
Please give me an advise what parameters I should set up in RMAN to backup database on another server's tape.
Best wishies,
GiviI am connected to the database server from the server
where I have tape, but Rman is searching tape on
database server.I am not sure I understabd the above statement, but at the Operating System Level, you must ensure that from the Server you are running RMAN, it is configured to see the Tape Drive of the other Server. Once the Remote Tape is mounted with any name (say sbt) on the Local Server (however it is done with), then RMAN can configure the channels to use it.
If you cannot get this access at the Operating System Level, then do not bother trying RMAN to access it. -
How to load configuration using Cisco USB port???
on USB-flush configuration there. I try to download it gives this:
Switch#copy usbflash0: 3560-ST
Source filename [3560-st]?
Destination filename [3560-ST]?
%Error opening usbflash0:3560-st (File not found)
What is the Problem? flash formatted on most Cisco (it has decreased in numbers from 16 GB to 2.75 GB)???Syntax is the one as Chandu poined out.
However, i see there is a space between usb0: and the filename.
"Switch#copy usbflash0: 3560-ST"
Make sure there is no space in the syntax above and also the file name is correct. -
I have a Diamond WR300N Range extender. How do I configure using Macbook Air?
Diamond WR300N range extender
try using th eusb plug and plug it into the computer than look under the "my cmputer" file and look for devices if you havnt already
-
Backup/restore using Stored porcedure
Hi,
Can any one tell how to backup/restore using stored procedure from schema....
becoz this script will be used by front end application..
How to do that?I "guess" you are trying to create some sort of ERP application which does everything inside-the-box. The reason for this guess is that few months back, I got a similar kind of request from a friend who runs an ISV and wanted me to write a code doing the same for his VB app. Well, my answer was same which you have got just now from other members. Backup/Recovery shouldn't be based on some home grown application , atleast as long as that app is not as robust as APPS or SAP or some thing like that. If you want to do some backup/recovery thing in a script, better you write it in some shell/batch script and run it. Don't try to push it in the some procedure which being tied to your application.
Sybrand mentioned two techniques, RMAN and DB Console, both will do your work excellently.
Just my 2 cents.
Aman.... -
How do you configure the set of port to use for FTP passive data connection
I was able to start the ftp server xml db and connect to it locally. When I tried to connect to it from home, I was able to log in but when i do a "get" command the sessions hangs. I also tried passive mode and do a "get" command and it gives me a connection refused error. I am using the default port 2100. I think this might be a firewall issue with the data connection port. I am not sure which range of ports to open for the passive ftp connection on the server side or where to go and set them for for the ftp server to use? Or this issue might not be firewall related??? Any thoughts. Thanks.
This is a typical problem with VPN/Firewall software and FTP on ports other than 21.
When you open the FTP data connection the FTP Server identifies which port the data will be sent on using the PORT command which is sent on the command port (typically 21 with a normal FTP server, 2100 by default with XDB). THe client then opens that PORT to accept the data (file, output of an ls etc).
As I understand it most VPN/Firewall are configured to monitor 21 for 'PORT' requests. They then understand to allow connection on the PORT number passed on the command PORT. Hence with Port 21 firewall / VPN software is not a problem. However since the XDB command PORT is something other than 21 they do not see / honour the PORT commands from the server and hence the client cannot open the data connection on the specified PORT
As to how to solve it, I wish I knew (After 5 years I still can't use XDB FTP from home to a machine in the office once the VPN tunnel is open :( ). I'm sure it's going to be firewall / VPN software specific and may need the VPN servers to be configured.
The best bet would be to run the FTP server on 21...
Add the following line to your listener.ora file
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP) (HOST = hostname) (PORT = 21))
(PROTOCOL_STACK = (PRESENTATION = FTP) (SESSION = RAW)))
and then restart the listener as root
Start the listener as root.
At the operating system prompt, enter tnslsnr with optional command line arguments. The usage is as follows:
tnslsnr [listener_name] [-user user] [-group group]
where:
Table 4-3 tnslsnr Utility Options
Option Description
listener_name
Specify the name of the listener. If omitted, the default name LISTENER will be used.
-user user
Specify the user whose privileges the listener will use when super user (root) privileges are not needed. After performing the privileged operations, the listener will give up root privileges irreversibly.
-group group
Specify the group whose privileges the listener will use when super user (root) group privileges are not needed. After performing the privileged operations, the listener will give up root group privileges irreversibly.
The listener will temporarily switch to the provided user and group immediately after startup. All subsequent operations will be done with the specified user and group privileges, except the system calls necessary to listen on configured endpoints. The listener will revert to super user (root) for a short period of time to listen on reserved addresses, such as TCP ports less than 1024. After the listener starts listening on all of its endpoints configured in listener.ora, it will switch to the specified user and group irreversibly. Therefore, the listener will give up the root privilege that it initially had. In the current release, -user and -group command line arguments only accept user and group identifiers specified in numeric form.
For example, to execute a root listener called mylsnr and have it use privileges of a user identified -
ISE backup not working while using tftp
I have configured a repository on ISE admin node to use tftp for taking backups.
repository master
url tftp://<IP>
I initiate backup on demand to use the defined repository and specify Application-only backup. After sometime, I see success on ISE node and "show backup history" also shows success
ise/admin# sh backup history
Thu Sep 27 06:12:43 UTC 2012: backup backup1-120927-060253.tar.gpg to repository master: success
Thu Sep 27 07:31:56 UTC 2012: backup backup1-120927-072227.tar.gpg to repository master: success
However, when I check on tftp server, I see nothing. No files with names backup1-120927-060253.tar.gpg or backup1-120927-072227.tar.gpg...Has anybody else seen similar issue? Is there a bug with tftp server backup on ISE nodes?
Thanks,
KashishKashish,
Can you try moving a small file over to the tftp server? Check the directory of the local disk and issue a a copy disk:/file tftp:/path.
See if that moves a file over. I havent personally used tftp I always use ftp.
Thanks,
Tarik Admani
*Please rate helpful posts* -
Hi Everyone.
Thanks in advance for your help.
Right off the bat let me say I am using Mavericks 10.9.1 on a 2011 Macbook Pro and using all Lacie external hard drives.
I am trying to get Time Machine to alternate between two attached external hard drives, trying to be safe in case one of the backup drives itself fails.
I have both drives set in Time Machine.
From what I gather Time Machine should by default alternate between drives when backing up (I would assume it does one big initial backup on each then subsequent backups are just changes).
But this is not how it seems to be working and I cannot find a straight answer despite much Googling and Foruming
Unfortunately it seems to only be backing up to "External Hard Drive 1".
There have been 4 backups since I set it up, all on "External Hard Drive 1", even though "External Hard Drive 2" is also attached and set in Time Machine.
I manually clicked "Back Up Now" and it started to work on "External Hard Drive 2" (like I want it to) for a minute but it appears to have stopped and gone back to backing up to "External Hard Drive 1".
Am I missing something? Does Time Machine only move on to another disk when the first one runs out of space? Do I have to turn one off in order to force it to back up to the other drive (that would be less convenient of course)?
I am hoping that I am missing something and that it will just alternate between the two. Otherwise it is not the most comforting and thorough backup system as I had hoped when I purchased the additional external hard drive.
I have a 1TB drive and a 500gig partition on another drive, both dedicated to backups (my Macbook HD is 475gig). It will take awhile for each to fill up and who knows what could happen during that time. Having Time Machine alternate between hard drives would be a nice small bit of security if the worst happened.
I realize that there are tons of other options for backing up but I just want to use Time Machine if I can.
Again thank you for your help!You cannot use Time Machine in that way. I'm not sure where you heard that Time Machine alternates between drives automatically. What you can do is create a mirrored RAID array for the backup. This automatically duplicates whatever is on one drive onto the other drive.
Both drives must be the same size, and prefereably, exactly the same make and model. RAIDs can be configured using OS X's Disk Utility.
RAID Basics
For basic definitions and discussion of what a RAID is and the different types of RAIDs see RAIDs. Additional discussions plus advantages and disadvantages of RAIDs and different RAID arrays see:
RAID Tutorial;
RAID Array and Server:
Hardware and Service Comparison.
Hardware or Software RAID?
RAID Hardware Vs RAID Software - What is your best option?
RAID is a method of combining multiple disk drives into a single entity in order to improve the overall performance and reliability of your system. The different options for combining the disks are referred to as RAID levels. There are several different levels of RAID available depending on the needs of your system. One of the options available to you is whether you should use a Hardware RAID solution or a Software RAID solution.
RAID Hardware is always a disk controller to which you can cable up the disk drives. RAID Software is a set of kernel modules coupled together with management utilities that implement RAID in Software and require no additional hardware.
Pros and cons
Software RAID is more flexible than Hardware RAID. Software RAID is also considerably less expensive. On the other hand, a Software RAID system requires more CPU cycles and power to run well than a comparable Hardware RAID System. Also, because Software RAID operates on a partition by partition basis where a number of individual disk partitions are grouped together as opposed to Hardware RAID systems which generally group together entire disk drives, Software RAID tends be slightly more complicated to run. This is because it has more available configurations and options. An added benefit to the slightly more expensive Hardware RAID solution is that many Hardware RAID systems incorporate features that are specialized for optimizing the performance of your system.
For more detailed information on the differences between Software RAID and Hardware RAID you may want to read: Hardware RAID vs. Software RAID: Which Implementation is Best for my Application? -
I like to use the new TC in my office as a time machine on a Windows Server. Is this possible, and how do i configure this?
In fact my plan is to make the first back up by connecting to the server via an ethernet cable, but thereafter i like to bring the TC to my home and perform the incremental backups over the internet. This is for safety reasons, in case for example the office is broken into, or flooded, or fire (god forbid).
I sincerely hope it is possible, and not complicated.
Alternatively i would not mind replacing our current Windows server 2003 with an Apple server, but all computers in the network (except mine) are Windows 7 or 8. Would it work?
Thanks in advance.
ParisI will consider the WD My Cloud device.
It is a NAS.. it is designed to provide a cheap centralised file storage.
What is NAS?? http://en.wikipedia.org/wiki/Network-attached_storage
A file server like windows uses heaps of power to do very little.. in your setup.. In most setups like SBS it will do exchange server and provide a heap of useful connectivity to your clients.
Since you are not using the windows server in anything but simple file serving you can replace with a NAS..
Problem with the TC is, it is a router with a hard disk inside.. designed specifically for Time Machine.. it fails to provide what a NAS does.. easy access to any clients, local or remote.. TC is designed by apple for apple and the rest of world is not really invited to the party.
It provides no backup.. no data protection.. and is so specifically apple orientated I do not think it works at all well with windows.
For a simple example.. windows will have file issues with large files.. because it is only NTserver FAT32 to windows.. bad luck if you have large files.. !!
Plainly if you use active directory in windows that facility is gone.
I just like Apple products, find them more stable than Windows and easier to use. Plus i can access the server from home if it is an Apple Server.
If you only need remote access for yourself that is fine.. too bad for the windows clients I guess.
Or you open it up to the world and bad luck for security.
Apple do not design for mixed environment.. in fact with the TC there is no provision for windows access officially at all.. so anything you do is a fudge.
You can use the TC for your Mac backups within the network.. that is fine. Apple provide no software at all to help with your windows clients. -
How to use 2 FTP Server in ALSB 3.0
We want to provide ftp tunneling functionality to any Billing System for ftping files to Payment Gateway System.For this we have one FTP server at Billing System and another FTP server at Payment gateway.We first need to pick the file from File System of Billing computer(using FTP server) and then transfer that vile via ALSB to File system of Payment Gateway(using FTP Server).Now I would like to know:
1) How to configure 2 FTP server in ALSB(in a single known_host file) ?
2)How many proxy and business services we need to make to complete this flow of transferring files?
If any one has some examples or config.jar files for the above scenario of transferring files,please chare it, that would be great help.
Thanks in advance!Hi all,
i am using osb10g3r ftp business service to poll the remote directory to retrieve file from there.i have configured download,error,archive directories accordingly. I am trying to read the file from the download directory to process the file , through a java call out. But while testing i am getting a exception, filenot found exception from the download directory.
can someone help me on this
Regards
shan
Maybe you are looking for
-
Access denied on applet in broswer - fine in applet viewer
I have written an applet that access a php file and sends a post message. I have tested the applet with the applet viewer and it succeeds each time. When I put the applet on a web page I get the following error: access denied (java.net.SocketPermissi
-
10.7.2 ask for shutdown
My iMac 21,5" with Lion 10.7.2 12G RAM 2,5Ghz intel core i5 iTunes version 10.5.3 After the iMac wakes up from sleep mode. It ask for shutdown and restart. Have any one tried this before ??
-
How to load the boot menu using the command line , after the configuration change ?
how to load the boot menu using the command line , after the configuration change ?
-
Why can't the Accordian widget's drop down box span full width in mobile layout?
I'm trying to create a simple drop down navigation for mobile. When the entire header is clicked, it expands down to reveal a dynamic vertical menu, which will cover the page content below, not push it down. I've taken an accordian widget and added a
-
Trouble importing video - blurred band across bottom of footage
I am in the process of importing footage captured by a Sony DV Handycam into iMovie HD. On the screen, a blurred out band appears at the bottom of each clip. Upon closer inspection, I noticed that the band is the footage that should appear at the top