How to boot leopard from cd?

Hey guys,
Maybe a silly question, but I need to know how to boot leopard from its insallation dvd, is that possible?
I would like to boot my mac from dvd, so that i can then use the disk utility to partition my internal hard drive, and i think this is only possible if you dont boot from the hd it self.
Obviously I am able to boot from the dvd in the way that it starts the leopard installation, but thats not what i need i guess? at least when the installation start, i dont see an option to start disk utility from there?
so i need to actually boot the system from the dvd, in order to partition "on the fly" without losing the data on my disk.
I hope someone knows.
thanks in advance.
cheers,

Hi,
Boot from the Install disc. Select the Language. Then as soon as the menu bar appears you'll see a Utilities Menu. Select Disk Utility from there.
cheers
mrtotes
EDIT: Level 4s always type faster than me!!!

Similar Messages

Can anyone boot Leopard from an external hard drive on an iMacPPC?

Can anyone boot Leopard from an external hard drive on a G5 iMac PowerPC? How?

Allan's answer is irrelevant as he refers to Snow Leopard. He must have isread your post!
Yes, you can and I do. The proviso is that the external hard drive is connected by firewire, as a PPC Mac cannot boot via USB.

How do install Leopard from intel to ppc by Firewire?

Can anyone tell me how to install Leopard from my intel macbook to my older ppc? When I try to install from firewire it says that the drive is going to GUID and non-bootable. My DVD drive on the PPC isn't good enough for the Leopard DVD. Any suggestions are appreciated.

I'm not commenting on whether the type of Mac is compatible with the Leopard install.
I'll offer suggestion for the firewire install. The objective is to take the Leopard DVD and transfer in some way to a firewire drive to be able to boot a PPC Mac and complete a Leopard install to the PPC Mac.
How? Take a firewire external drive and partition it in two. One for your data and the other (7.2 gigs) max, for the ability to restore the Leopard DVD to that smaller partition. Once restored you'll be able to boot(using system startup control panel) and install Leopard to a PPC Mac.
The rule to follow is to use APM ie Apple Partition Map to boot PPC Macs. GUID mapping is for intel Macs. You use options within Disk Utility ti select which way to go. You cannot have both on one firewire hard drive. I use two firewire hard drives: one APM and the other GUID.
How to setup the small partition? Connect firewire drive to your PPC Mac. Open disk utility. Create your two partitions(remember when you do this the drive is formatted and all data is gone, so backup first). Remember to use option and select APM, although on a PPC Mac it should be by default and ditto if on an intel Mac for GUID. Once the partitioning is complete, select Restore and while using the left hand column(just read the instruction in the disk utility window) and assuming you now have the Leopard DVD on the desktop , drag the install OSX section from the left hand column to "source" and then drag the Leopard small partition from the left hand column to "destination." Wait 20 minutes and you are completed. Now you can boot from the firewire drive and install Leopard to a PPC Mac.

How to install leopard from a DMG file instead of DVD

How to install leopard from a DMG file instead of DVD, When i open this file, click restart, NOTHING happened!!!!!!

Use Disk Utility to restore the DMG to a blank partition, then use the Startup Disk preferences pane to reboot from that partition. Why not just install from the DVD, though?

How to install Leopard from an external DVD reader?

Hi,
I've bought Leopard today. unfortunately, it's not yet installed on my PowerBook. As my SuperDrive is dead, I use now an external DVD (Lacie Portable DVD-RW), but it doesn't work. I can read the Leopard install DVD, but when it reboot, it reboot on my current installation.
I've tried the following during the boot sequence:
- alt pressed, but I can only see my main HDD
- c pressed, but I boot on my current installation
Can you tell me if it is possible to install Leopard from an external DVD, and how can I do that ?
Thanks in advance.
Regards,
Emmanuel Di Pretoro

Can you tell me if the same problem occur with a FireWire external DVD ?
It does not occur on your model of Mac.
(25504)

How to boot up from firewire disk?

Hi everyone,
I just bought a 250Gb Lacie D2 triple interface external hard drive to go with my 15" 1.25ghz G4 powerbook.
I partitioned the External drive into two volumes, one of which I will reserve exclusively for backing up my entire Powerbook hard drive.
I used the software (Silverkeeper) that came with the Lacie disk to copy the powerbook hard drive onto the Lacie disk. When I commenced the copying, a dialog box asked me if I wanted to make the copy 'bootable' I clicked yes.
Now for my question..... How do I boot up from the copy???
I had assumed that if I switched off the powerbook & then re-started it, (with the Lacie disk connected... Firewire 800) that I would then be given the option of booting from either the Powerbook hard drive OR the Lacie hard drive. Not so.... Powerbook booted up as per normal, having 'recognised' the Lacie disk & placed it's icons on my desktop.
Obviously there is a simple step I am unaware of, probably holding down a combination of keys whilst re-booting???
So....How do I boot up from the copy?
regards
Ian
15 Powerbook 1.25Ghz Mac OS X (10.4.4) 1.25gb ram

Well to be accurate it is not at all "permanent" - a better and more usefully accurate term would be persistent.
If you are updating the OS on it you might want it to persist through reboots vs using the very time consuming Option key method each time.
To go back to the original boot disk or any other one just go to preferences and select the one you want again. Much faster.

How to boot always from a firewire disk?

Hello,
I hope someone can help me on this.
My HD is almost dead and it's making a lot of noise. I have managed to create a boot disk
on an external disk connected through Firewire.
What shall I do now to have the HD definetly unmounted and have the boot always from the firewire disk?
Thanks in advance
Tom

I've had a similar problem with an external drive that was USB powered.
In my case, the system was looking for a boot device before the drive was ready.
I had a friend that was good with OpenFirmware add a delay before booting to give the drive time to become ready. Added 5 seconds to the boot process, but it works!
Like cldjr said, hold the Option key (⌘) when powering up, if the drive shows up there, I'd guess it's the problem I described...
Anyone good with OpenFirmware??

How do I boot Leopard from external hard drive?

I'm currently staring off into space... my 3 month old MBP seems to have finished its painfully long boot and all that appears the Leopard background. The local Mac guru isn't available until Monday but did tell me I need to boot from my external hard drive. Um, how do I boot from external hard drive?
The cause of the problem: inserting flash drive powering up.
Tried safe boot. Only difference was iCal reminder popped up in space.
Mac guru told me do NOT use install disks!
Help!
AR

Apple support has told me that you cannot boot a MBP from an external drive when Leopard is installed on a MBP.
That is just plain wrong.
1) Hook up your external drive. Use FireWire for better performance.
2) Launch Disk Utility and highlight the actual drive icon at the left. Click on the Partition tab.
3) In the Partition section, click on the Options button. Click on the radio button for "GUID Partition Map". This is the option you must use in order for a drive to be bootable on an Intel based Mac. Click OK.
4) Set up your partitions however you want and click the Partition button at the lower right.
From here, you can either clone your internal drive to the external, or install Leopard on it from scratch.

How to reinstall Leopard from another source than the install disk?

Hi there. Great forum full of information but I somehow could not find the answer to my problem.
I own a MacBook Pro and for some reason, the Optical drive refuses to read DVD and CD. It still accepts blank CD and does write....strange.
I can live with that, but what will I do if and when my Mac needs access to the install disk that came with it?
Today I partitioned an external Lacie HD with the intention of installing OS Leopard on it. I thought this would be an ideal solution as a back up strategy. Files in one volume, OS in another.
I have copied the content of both install disks on my desk top through firewire using my good lady's macbook (tiger) but when I click on the install icon, I get a negative message.
[IMG]http://img99.imageshack.us/img99/5370/picture1tk.png[/IMG]
[IMG]http://img21.imageshack.us/img21/7129/picture2gn.png[/IMG]
What is the way of doing this?
Also, is it possible to reformat an reinstall the OS through firewire using the other macBook optical drive?
Thanks

You must be sure the drive is partitioned GUID or it will not boot a computer from the cloned installer disc.
You may want to consider getting a flash drive. An 8 GB flash drive will hold the OS X installer and a 16 GB one will hold the installer and Disc 2 (need to partition the flash drive.) Take care what brand you buy. Some don't work too well for booting Macs. I've had good success with PNYs. Prep them as follows:
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
The above works, also, for external hard drives.

How to boot up from new harddrive install

I'm about to replace my harddrive before it crashes. My question is, can I copy my existing HD data onto the new harddrive before installing it? I have a firewire case I can use for this process. I have a freeware copy of Superduper I can use.
I have replaced my HD once before, but it was after my drive crashed so I had to do a new install of OS X and then replace all apps one-by-one. I'm hoping to avoid this by replacing the drive early this time, and it would be great if a cloned copy of my contents put onto the new drive before install could allow me to boot up and operate normally. Thanks!

Sure. Put the new drive in the FW enclosure and prep the drive:
Extended Hard Drive Preparation
1. Open Disk Utility in the Utilities folder.
2. After DU loads select the new hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
7. Repeat Steps 4-6 for each volume created if more than one.
Next, clone your old system to the new drive:
How to Clone Using Restore Option of Disk Utility
1. Open Disk Utility from the Utilities folder.
2. Select the external drive's volume from the left side list.
3. Click on the Erase tab in the DU main window. Set the format type to Mac OS Extended (journaled) and click on the Erase button. This step can be skipped if the destination has already been freshly erased.
4. Click on the Restore tab in the DU main window.
5. Select the the external drive's volume from the left side list and drag it to the Destination entry field.
6. Select the startup volume from the left side list and drag it to the Source entry field.
7. Double-check you got it right, then click on the Restore button.
8. Select the destination drive on the Desktop and press COMMAND-I to open the Get Info window. At the bottom in the Ownership and Permissions section be sure the box labeled "Ignore Permissions on this Volume" is unchecked. Verify the settings for Ownership and Permissions as follows: Owner=system with read/write; Group=admin with read/write; Other with read-only. If they are not correct then reset them.
Upon completion of cloning open the Startup Disk preference, select the icon for the external drive, then click on the Restart button. If all goes well your computer should start up from the external drive. Now shut down and swap drives.

How to Download Leopard from the Apple site

Well my MBP dumped its hard drive this weekend. I have installed a new HD but I can't find my Leopard installation disk any where.
Is there a way I can download the entire OS from the Apple site?

No. Your Mac if it came with Leopard shipped with operating system discs for Leopard restoring. If you lost your discs, call AppleCare for replacement discs. If you bought your Mac from a non-Apple authorized source, contact them for the discs, and ask them to contact AppleCare for the discs if they lost them. The discs that shipped with the Mac should not be separated from the Mac, and should always be kept in a safe place.

How to boot OSX from SSD?

Hi,
I have just installed a OWC Data Double in my Macbook Pro 13" 2010.
What I want to do is boot up OSX from the SSD and also to have iPhoto Library on this for fast access.
I would like the HDD for everything else.
What is the best way to get the OSX on the SSD and to leave everything else on the HDD?
I currently have the sparsebundle file on Airport Timecapsule from the regular backups.
Thanks in advance.
Stelios

Topher Kessler California
It does not matter what bay to use.
You would think that would be the case,.....installing several shows otherwise.
Clintonfrombirmingham, Eww and others have noted that that isnt the case either.
Love your MacFixit page by the way
kudos

I'm stuck, how to boot up from an ext HD, wih FW/400

You can tell the OS I'm running see below. I have a 1 TB DR that I'm goign to GUIDD
Partition, and formatted for the MAC Extended Journal. However, I don't know if I need to hit the Option+Control keys, or do I need to go to Systems Preferences - Start UP Disk. Then what?

Just the Option key should bring up the Drives that are bootable. Startup Disk CP can work too.

How do I boot Mac OS X Leopard from an external hard drive onto an eMac?

My eMac's internal hard drive died a while ago, and I was finally able to successfully able to install Mac OS X Leopard onto an external hard drive. However, my eMac still refuses to boot Leopard. I only keep being put on the OS Install/Upgrade screen. After install, I selected the Start-up Disk utility and chose my hard drive. Upon restart I find myself on the Install/Upgrade screen as I said earlier. I tried restarting again, but this time I pressed the option key to select a boot disk. However, only my Mac Install Disk shows up.

How is the external HD connected - USB or Firewire? Most Power PC Macs can't boot from a USB connected external HD.
 Cheers, Tom

My Imac fails when I try to upgrade from Snow Leopard 10.6.8. I have to boot up from disk. Does anyone know how to overcome this problem?

My iMac fails when I try to upgrade from Snow Leopard 10.6.8. I have to boot up from disk. Does anyone know how to overcome this problem?   I need to upgrade in order to install latest software.

It would be lovely to know what your talking about. Upgrading from Snow Leopard does not involve discs.
Upgrading to Lion
If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
You can purchase Lion at the Online Apple Store. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
     Lion System Requirements
       1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
           or Xeon processor
       2. 2GB of memory
       3. OS X v10.6.6 or later (v10.6.8 recommended)
       4. 7GB of available space
       5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase a redemption code at the Online Apple Store: OS X Mountain Lion. Mountain Lion is $19.99 plus tax. Use the code to redeem a download of Mountain Lion from the App Store. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
     OS X Mountain Lion - System Requirements
       Macs that can be upgraded to OS X Mountain Lion
         1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later.
         2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model
             Identifier 5,1 or later.
         3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later.
         4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later.
         5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later.
         6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later.
         7. Xserve (Early 2009) - Model Identifier 3,1 or later.
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
     Are my applications compatible?
         See App Compatibility Table - RoaringApps.
Upgrading to Yosemite
You can upgrade to Yosemite from Lion or directly from Snow Leopard. Yosemite can be downloaded from the Mac App Store for FREE.
Upgrading to Yosemite
To upgrade to Yosemite you must have Snow Leopard 10.6.8 or Lion installed. Download Yosemite from the App Store. Sign in using your Apple ID. Yosemite is free. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
    OS X Mavericks/Yosemite- System Requirements
    Macs that can be upgraded to OS X Yosemite
         1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
         2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
         3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
         4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
         5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
         6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
         7. Xserve (Early 2009) - Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
     Are my applications compatible?
         See App Compatibility Table - RoaringApps.

How to boot leopard from cd?

Similar Messages

Maybe you are looking for