How to configure 6533 both as input as well as output

Hello,
I am using 6533 for acquiring data from the peripheral. I am recieving 16 bit data(so i am using port 0 and 1) . i am using pattern generation mode for acquiring the data.i am writing the application on vc++. Now i am required to use the one line in the remaining 16 bit(first bit of port 3) as output port. Can some one me how to configure the port in vc++. which API to be used DIG_grp_congif,DIG_prt_config??????
waiting for reply
praveen

Hi Praveen,
You would want a combination of NI-DAQ function calls for input and for output. NI-DAQ ships with example programs for digital input and output for VC++ as long as you installed support for VC++ with your install of NI-DAQ.
You can do a repair on your install by going to Add/Remove Programs and adding the support from there. If you already have the support installed for it, you'll find your examples in the following directory: "C:\Program Files\National Instruments\NI-DAQ\Examples\VisualC".
The two examples you'll want to merge are:
1) DIdoubleBufPatternGen653x
2) DOdoubleBufPatternGen653x
Hope that helps. Have a good day.
Ron

Similar Messages

AT-MIO-16E-10 Gate signal,how can i configure it as in input or as an output ?

Hi there ! I have AT-MIO-16E-10 board and i want to control a counter (the GPCTR0 counter of the bord) to count up depending on the gate signal.Now i have the following missunderstanding.I've read in the AT-MIO-16E-10 manual that the gate signal can be treated eather as an input or as an output.So i want to control my counter (to count up) until a signal that comes on my gate counter's entry changes his states from 1 to 0 (to reset the counter) and then when it changes his states back to 1 form 0 i.e a transition from 0 to 1 to start counting again from zero.Now here i have 2 questions : 1. How can i config the gate signal as an input signal (in the AT-MIO-16E-10 manual it sais that the signa
l can be treated as an input or output and it's known if i configure the port as an output and if i came with an external signal to the gate i can damage the board if the signal it's set to zero ) 2. What it's the default state of the gate signal ?
Any vi files would be very usefully,Thank you very much for reading this and i'll be waiting for your answers as quick as possible.

Antonios,
The shipping example VI Count Edges does what you describe.
>Quoted from VI Description
Count Edges (DAQ-STC).vi
DESCRIPTION:
This VI counts rising edges, using an STC based device (e.g.: E-series). The counter increments its event count everytime a pulse comes into its source input. A gate signal can be added such that if a low signal occurs on the gate, then the counter will pause (scroll the front panel left to access the gate settings). The current value of the counter is read continuously in the while loop, until the Stop button is clicked or an error occurs.
I/O CONNECTIONS:
Connect the gating signal, if any, to the gate input of the selected counter.
If you selected the Source Selection to be "PFI line", connect your event count base signal to the PFI line indicated by "Source PFI line number used". (If you selected "Internal Timebase", no source connection is necessary.)
NOTE: For actual I/O pin numbers, please refer to your hardware user manual.
INSTRUCTIONS:
1. Enter the device and counter you want use.
2. Make your Source selections, as desired.
3. Optional controls are located on the left side of the front panel. You will have to use your scroll bar to reach these.
4. Connect your signals as described below in I/O CONNECTIONS.
5. Run the VI.
>End quote
If you look inside the Diagram of the Count Edges VI you will see a subVI, Group Config CTR, that has a constant set to "simple event counting." This configures the gate in the correct manner. You have 17 or so options to choose from (right-click to see the other choices). Each choice configures the counters as needed. No special effort is needed on your part.
If you really must know more details double-click on the Group Config CTR icon. On the Diagram of that VI is a Call Library function. Right-Click that and see more ugly details that you don't need to know. The functions of the counters are fully implemented by the options already available, so you don't need to know how the details, but it is intersting.
Hints:
Keep in mind that the counters require TTL level signals. 0V to 5V. Limit the current to the level the DAQ board can handle. You will false trip the counter if your low is higher than 0.8V. I have had problems with this when using noisy signals.
Also make sure you debounce any switches you wire to the counters. It is instructive to hook up an unbounced switch to the counter inputs and see just how many false trips they can generate!
Mike

How to merge five different xml input files into three output files

Hi All,
Can you please explain me to merge 5 different xml input files into 3 output xml files.
I'm looking forward for ur suggestions...
Thanks
Pullarao

HI
Please see the below links
/people/pooja.pandey/blog/2005/07/27/idocs-multiple-types-collection-in-bpm - Collection of IDoc to Single File
http://help.sap.com/saphelp_nw04/helpdata/en/3c/831620a4f1044dba38b370f77835cc/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/62/dcef46dae42142911c8f14ca7a7c39/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/de/766840bf0cbf49e10000000a1550b0/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/cb/15163ff8519a06e10000000a114084/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/08/16163ff8519a06e10000000a114084/content.htm
Many other examples can be found under the following link at help.sap.com
http://help.sap.com/saphelp_nw04/helpdata/en/14/80243b4a66ae0ce10000000a11402f/frameset.htm
And some weblogs
https://weblogs.sdn.sap.com/pub/wlg/1403 [original link is broken] [original link is broken] [original link is broken]
/people/siva.maranani/blog/2005/05/22/schedule-your-bpm *****
/people/krishna.moorthyp/blog/2005/06/09/walkthrough-with-bpm
/people/michal.krawczyk2/blog/2005/06/11/xi-how-to-retrieve-messageid-from-a-bpm
/people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit
/people/sravya.talanki2/blog/2005/08/24/do-you-like-to-understand-147correlation148-in-xi
/people/michal.krawczyk2/blog/2005/09/04/xi-do-you-realy-enjoy-clicking-and-waiting-while-tracing-bpm-steps *****
/people/udo.martens/blog/2005/09/30/one-logical-system-name-for-serveral-bpm-acknowledgements *****
/people/sudharshan.aravamudan/blog/2005/12/01/illustration-of-multi-mapping-and-message-split-using-bpm-in-sap-exchange-infrastructure
/people/kannan.kailas/blog/2005/12/07/posting-multiple-idocs-with-acknowledgement
Also have a look at these seminars,
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/media/uuid/daea5871-0701-0010-12aa-c3a0c6d54e02
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/media/uuid/e8515171-0701-0010-be98-e37bec4706cc
<b>BPM CollectPattern..</b>
http://help.sap.com/saphelp_nw2004s/helpdata/en/08/16163ff8519a06e10000000a114084/frameset.htm
Thanks !
Regards
Abhishek Agrahari
Questions are welcome here!!
<b>Also mark helpful answers by rewarding points </b>

How do I convert a deciaml input to a hexidecimal output in labview?

Can somebody please explain what seems like a simple conversion ?
I would like to convert a decimal input to a Hexidecimal output:
i.e input value of 20000
converting to a hexidecimal output of 4E20
hope you can help
AW

Hi Anil,
Are you looking for this one?
See the attachment:
Thanks as kudos only
Attachments:
dectohexph.vi ‏10 KB

Does the 3.5mm Headphone Plug accept input as well as output?

My Computer is:
MacBook Pro (Retina, 15-inch, Mid 2014)
10.10.2 (14C109)
2.8 GHz Intel Core i7
16 GB 1600 MHz DDR3
500 GB SSD
NVIDIA GeForce GT 750M 2048 MB
Model Name: MacBook Pro
Model Identifier: MacBookPro11,3
Processor Name: Intel Core i7
Processor Speed: 2.8 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 6 MB
Memory: 16 GB
Boot ROM Version: MBP112.0138.B14
SMC Version (system): 2.19f12
OSX: 10.10.2 (14C109)
I've got mixed answers from Apple Support and their engineers. The engineers might not understand the question, but it is simple.
Again, Apple only provides the most minimum of details possible, so there are no technical specs to fall back on.
By referring to it as a Headphone jack we can infer you can plug in a headset and listen to iTunes. Researching further I find you can plug in a 3.5 mm Headphone, provided you get a connection that follows the four connector Apple standard.
Since a headphone has a microphone I would assume that means the headphone jack can support input. For example, spoken words. Will the headphone jack support a 3.5 mm Apple specific wire connected to the MacBook and the other end to another device like an MP3 player, but using the proper four wire configuration for the MP3 Player?
If so, what application is available on the MacBook Pro to get the analog data and then manipulate it into something digital?

Use a USB audio device, the Mac only has a headset/mic combo input, the quality is OK for that but not much else.

Does the late '09 24" iMac minidisplay port allow for video input as well as output?

Greetings,
I own a 24" 2.66 GHz Intel Core 2 Duo iMac with the Nvidia 9400 card. It's nearing the end of it's gaming life but I still want to use it for everything else after I get my new tower. Everything I can find in reguards to using an iMac as a monitor for a different computer references the 27" iMac one model newer than my current computer. Is the minidisplay port on my machine able to accept an input or am I forced to get a subpar monitor for my 2nd machine? Thanks!
~Dan

Only the 27" can be used in target display mode.

Is DisplayPort an input as well as output on macbook pro?

I have a 2011 Macbook Pro 17" and i know that it has Thunderbolt/DisplayPort. i know the cinema displays use displayport input and the macbook can provide the output signal for an external monitor, however i want to do just the opposite and use my macbook pro screen as a display for my xbox360. I was looking at the Atlona DP300 which converts and scales a 1080p HDMI signal to a 1920x1200 resolution output in the form of display port, however im trying to find out if my macbook pro could accept this signal. the maximum resolution of my screen is 1920x1200. if this is possible, what software would need to be used since i know the input would have to actually be through the operating system as the screen will not operate independently.
thanks a bunch

Hi a,
That's an interesting question. On the Thunderbolt page (http://www.apple.com/thunderbolt/) it says "Which means you can connect external devices like . . . video capture solutions directly to MacBook Pro or iMac — and get PCI Express performance," and lists "Video Capture: Blackmagic UltraStudio 3D, Matrox MX02." Note that BUS 3D is "only $995," and the MX02 only twice that much!
So, it sounds like the potential is there, but I think you've asked the operative question: "what software would need to be used?" And I suspect that at this point in time, although the hardware potential is there, the software to control exactly what you want to do, with the hardware you want to use, is not.
Somebody's always got to be the first one to try something, so maybe s/he already has and will post here. If not, and you give it a try, I hope we'll hear from you. Good luck to you.

How to configure BODS in network environment with NAT ?

Hi Team,
Now we are working on POC of BO Data Services 4.0 with SI partner and they reported us that a communication error (error code:BODI-1241023) occurred when they started a job from Designer.
They can do it without any problems in the following two cases.
1. from Designer which is installed in the CMS/JobServer machine
2. from Designer which is installed in local PC within internal network (without firewall / NAT)
That is, the cause is Firewall with NAT(Network Address Translation) between Designer and JobServer/CMS.
And, they can log on to CMS/JobServer with NAT environment, however, cann't start a job from Designer.
The port #3500 for JobServer is open. They confirmed that they could log on to the JobServer in the event log
of the JobServer.
That is, Designer -> CMS/JobServer communication is OK, but JobServer -> Designer communication must be NG.
Could you advise us how to configure BODS both client and server sides in the network environment with NAT ?
Thanks and best regards,

HI Buddy,
You can achieve this by $FLEX$, create first value set, and assign it to first field. Create second value set based on first value set using $FLEX$.
follow steps mentioned in the bellow link
http://erpschools.com/articles/usage-of-flex

TS3280 How can i enable both paired bluetooth and ios keyboard input at the same time?

How can i enable both paired bluetooth and ios keyboard input at the same time?
This is needed for the app im working on. Need some user input via keypad as well as scanner input via a paired bluetooth scanner.

You probably should not be using a keyboard bluetooth profile for a scanner, I am not a developer for apple so do not know the location for you to find out the correct profile you should be using for an input device that is not a keyboard. Sorry,
I am sure if you navigate the apple developer site you will probaly finmd what you're looking for.
https://developer.apple.com

How to configure content presenter taskflow parameters both design time

Hi,
I want to add content presenter taskflow to my portal page and want to configure taskflow parameters at both design and runtime?
So would like to know how to add content presenter taskflow(not content) to my portal page and how to configure parameters at both design and runtime?

Hi Yannick,
Going through the links which you have provided and will come back to you I face any problem.
Before going through the link I would like to know how to get content from ucms from specifying a query rather than getting from the entire folder.
Yes I am aware similar to the folder option you can specify a query but need help on writing a query and what parameters need to be mentioned in the query.
One more doumb question about where content presenter taskflow is present in the jdev so that I can drag and drop on my portal page.

How to configure Enterprise Manager both node (2 node) RAC?

Hi,
I have installed oracle 11g r2 rac with asm in two nodes. OS is hp-Unix.
I have installed oracle11g Active Data Guard using Single alone Database.
Both RAc and Active Data Guard works fine.
I have not configure Data Guard Broker.
I have configure Enterprise Manager during RAC database installation.
When I start Enterprise Manager from node1 its address to node1
but when I start Enterprise Manager from node2 it also addressed to node1.
When both node is up and running, I can connect from Enterprise Manager.
When node2 is down but node1 is up then also I can connect from Enterprise Manager
but when node1 is down and node2 is up I can't connect from Enterprise Manager.
Question: How to configure Enterprise Manager so that I can connect through it whenever any single node is running?
Thanks
Solaiman

http://www.gokhanatil.com/2012/04/manage-your-existing-data-guards-with.html

How to configure sso with SSL step by step

Purpose
In this document, you can learn how to configure SSO with SSL. After user have certificate installed in browser, he can login without input username and password.
Overview
In this document we will demonstrate:
1.     How to configure OHS support SSL
2.     How to Register SSO with SSL
3.     Configure SSO for certificates
Prerequisites
Before start this document, you should have:
1.     Oracle AS 10g infrastructure installed (10.1.2)
2.     OCA installed
Note:
1.     “When you install Oracle infrastructure, please make sure you have select OCA.
2.     How Certificate-Enabled Authentication Works:
a.     The user tries to access a partner application.
b.     The partner application redirects the user to the single sign-on server for authentication. As part of this redirection, the browser sends the user's certificate to the login URL of the server (2a). If it is able to verify the certificate, the server returns the user to the requested application.
c.     The application delivers content. Users whose browsers are configured to prompt for a certificate-store password may only have to present this password once, depending upon how their browser is configured. If they log out and then attempt to access a partner application, the browser passes their certificate to the single sign-on server automatically. This means that they never really log out. To effectively log out, they must close the browser.
Enable SSL on the Single Sign-On Middle Tier
The following steps involve configuring the Oracle HTTP Server. Perform them on the single sign-on middle tier. In doing so, keep the following in mind:
l     You must configure SSL on the computer where the single sign-on middle tier is running.
l     You are configuring one-way SSL.
l     You may enable SSL for simple network encryption; PKI authentication is not required. Note though that you must use a valid wallet and server certificate. The default wallet location is ORACLE_HOME/Apache/Apache/conf/ssl.wlt/default.
1.     Back up the opmn.xml file, found at ORACLE_HOME/opmn/conf
2.     In opmn.xml, change the value for the start-mode parameter to ssl-enabled. This parameter appears in boldface in the xml tag immediately following.
<ias-component id="HTTP_Server">
<process-type id="HTTP_Server" module-id="OHS">
<module-data>
<category id="start-parameters">
<data id="start-mode" value="ssl-enabled"/>
</category>
</module-data>
<process-set id="HTTP_Server" numprocs="1"/>
</process-type>
</ias-component>
3.     Update the distributed cluster management database with the change: ORACLE_HOME/dcm/bin/dcmctl updateconfig -ct opmn
4.     Reload the modified opmn configuration file:
ORACLE_HOME/opmn/bin/opmnctl reload
5.     Keep a non-SSL port active. The External Applications portlet communicates with the single sign-on server over a non-SSL port. The HTTP port is enabled by default. If you have not disabled the port, this step requires no action.
6.     Apply the rule mod_rewrite to SSL configuration. This step involves modifying the ssl.conf file on the middle-tier computer. The file is at ORACLE_HOME/Apache/Apache/conf. Back up the file before editing it.
Because the Oracle HTTP Server has to be available over both HTTP and HTTPS, the SSL host must be configured as a virtual host. Add the lines that follow to the SSL Virtual Hosts section of ssl.conf if they are not already there. These lines ensure that the single sign-on login module in OC4J_SECURITY is invoked when a user logs in to the SSL host.
<VirtualHost ssl_host:port>
RewriteEngine on
RewriteOptions inherit
</VirtualHost>
Save and close the file.
7.     Update the distributed cluster management database with the changes:
ORACLE_HOME/dcm/bin/dcmctl updateconfig -ct ohs
8.     Restart the Oracle HTTP Server:
ORACLE_HOME/opmn/bin/opmnctl stopproc process-type=HTTP_Server
ORACLE_HOME/opmn/bin/opmnctl startproc process-type=HTTP_Server
9.     Verify that you have enabled the single sign-on middle tier for SSL by trying to access the OracleAS welcome page, using the format https://host:ssl_port.
Reconfigure the Identity Management Infrastructure Database
Change all references of http in single sign-on URLs to https within the identity management infrastructure database. When you change single sign-on URLs in the database, you must also change these URLs in the targets.xml file on the single sign-on middle tier. targets.xml is the configuration file for the various "targets" that Oracle Enterprise Manager monitors. One of these targets is OracleAS Single Sign-On.
1.     Change Single Sign-On URLs
Run the ssocfg script, taking care to enter the command on the computer where the single sign-on middle tier is located. Use the following syntax:
UNIX:
$ORACLE_HOME/sso/bin/ssocfg.sh protocol host ssl_port
Windows:
%ORACLE_HOME%\sso\bin\ssocfg.bat protocol host ssl_port
In this case, protocol is https. (To change back to HTTP, use http.) The parameter host is the host name, or server name, of the Oracle HTTP listener for the single sign-on server.
Here is an example:
ssocfg.sh https login.acme.com 4443
2. Restart OC4J_SECURITY instance and verify the configuration
To determine the correct port number, examine the ssl.conf file. Port 4443 is the port number that the OracleAS installer assigns during installation.
If you run ssocfg successfully, the script returns a status 0. To confirm that you were successful, restart the OC4J_SECURITY instance:
ORACLE_HOME/opmn/bin/opmnctl restartproc process-type=OC4J_SECURITY
Then try logging in to the single sign-on server at its SSL address:
https://host:ssl_port/pls/orasso/
     3. Back up the file targets.xml:
cp ORACLE_HOME/sysman/emd/targets.xml ORACLE_HOME/sysman/emd/targets.xml.backup
4. Open the file and find the target type oracle_sso_server. Within this target type, locate and edit the three attributes that you passed to ssocfg:
·     HTTPMachine—the server host name
·     HTTPPort—the server port number
·     HTTPProtocol—the server protocol
If, for example, you run ssocfg like this:
ORACLE_HOME/sso/bin/ssocfg.sh http sso.mydomain.com:4443
Update the three attributes this way:
<Property NAME="HTTPMachine" VALUE="sso.mydomain.com"/>
<Property NAME="HTTPPort" VALUE="4443"/>
<Property NAME="HTTPProtocol" VALUE="HTTPS"/>
5.Save and close the file.
6.     Reload the OracleAS console:
     ORACLE_HOME/bin/emctl reload
7. Issue these two commands:
ORACLE_HOME/opmn/bin/opmnctl restartproc process-type=HTTP_Server
ORACLE_HOME/opmn/bin/opmnctl restartproc process-type=OC4J_SECURITY
Registering mod_osso
1.     This command sequence that follows shows a mod_osso instance being reregistered with the single sign-on server.
$ORACLE_HOME/sso/bin/ssoreg.sh
     -oracle_home_path $ORACLE_HOME
     -config_mod_osso TRUE
     -mod_osso_url https://myhost.mydomain.com:4443
2.     Restarting the Oracle HTTP Server
After running ssoreg, restart the Oracle HTTP Server:
ORACLE_HOME/opmn/bin/opmnctl restartproc process-type=HTTP_Server
Configuring the Single Sign-On System for Certificates
1.     Configure policy.properties with the Default Authentication Plugin
Update the DefaultAuthLevel section of the policy.properties file with the correct authentication level for certificate sign-on. This file is at ORACLE_HOME/sso/conf. Set the default authentication level to this value:
DefaultAuthLevel = MediumHighSecurity
Then, in the Authentication plugins section, pair this authentication level with the default authentication plugin:
MediumHighSecurity_AuthPlugin = oracle.security.sso.server.auth.SSOX509CertAuth
2.     Restart the Single Sign-On Middle Tier
After configuring the server, restart the middle tier:
ORACLE_HOME/opmn/bin/opmnctl restartproc process-type=HTTP_Server
ORACLE_HOME/opmn/bin/opmnctl restartproc process-type=OC4J_SECURITY
Bringing the SSO Users to OCA User Certificate Request URL
The OCA server reduces the administrative and maintenance cost of provisioning a user certificate. The OCA server achieves this by authenticating users by using OracleAS SSO server authentication. All users who have an Oracle AS SSO server account can directly get a certificate by using the OCA user interface. This reduces the time normoally requidred to provision a certificate by a certificate authority.
The URL for the SSO certificate Request is:
https://<Oracle_HTTP_host>:<oca_ssl_port>/oca/sso_oca_link
You can configure OCA to provide the user certificate request interface URL to SSO server for display whenever SSO is not using a sertificate to authenticate a user. After the OracleAS SSO server authenticates a user, it then display the OCA screen enabling that user to request a certificate.
To link the OCA server to OracleAS SSO server, use the following command:
ocactl linksso
opmnctl stoproc type=oc4j instancename=oca
opmnctl startproc type=oc4j instancename=oca
You also can use ocactl unlinksso to unlink the OCA to SSO.

I have read the SSO admin guide, and performed the steps for enabling SSL on the SSO, and followed the steps to configure mod_osso with virtual host on port 4443 as mentioned in the admin guide.
The case now is that when I call my form (which is developed by forms developer suite 10g and deployed on the forms server which is SSO enabled) , it calls the SSO module on port 7777 using http (the default behaviour).
on a URL that looks like this :
http://myhostname:7777/pls/orasso/orasso.wwsso_app_admin.ls_login?Site2pstoreToken=.......
and gives the error :
( Forbidden
You don't have permisission to access /sso/auth on this server at port 7777)
when I manually change the URL to :
https://myhostname:4443/pls/orasso/orasso.wwsso_app_admin.ls_login?Site2pstoreToken=.......
the SSO works correctly.
The question is :
How can I change this default behaviour and make it call SSO on port 4443 using https instead ?
Any ideas ?
Thanks in advance

How to configure Firefox to use OpenVPN?

summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>

You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need.

How to configure oracle listener profile for multiple oracle database

Hi,
I am going to install solution manager system in the same server of ERP EHP4 on Windows. Both DB are oracle.
I'd like to know how to configure listener in this kind of envirnmonent.
a. use two listener and different ports
b. use same listener but different ports
c. use same listener and same port
Which is the correct mothed?
And, after installation, there seem three set of profiles of listten, one for ERP, one for SLM, and the other for OS?(%windir%system32), which one is functional?
Please advise.
Thanks a lot.
Regards,
Alex

Hi,
standard installation is creating new configs for listener for each instance.
I would recommend to use one listener per each instance.
YOU CAN NOT HAVE one port number for two differnet systems!
If you want to use one listener than you must adapt tnsnames.ora, listener.ora and ensure that both systems will use different port numbers.
For example PORT= 15<system number>
Peter

How to configure 3 different members under a single Month column

Hi SAP Gurus,
My client requirement is to show the report in following format, where under a Month column 3 different columns having
1) Quantity (Number of unit ) of a product,
2) its rate (Amount per unit), and
3) Total (amount)    will appear in a single report.
   I have Month as a Time Dim, while Qty, Rate and Total are members of account dim.
Que: How to configure such scenario in a single report?
Jan.2011
Product Category:            Qty (Input)   Rate (Input)   Total (Output)
Product 1
Product 2
Product 3
Product 4
Group1
     Where: Total = Qty X Rate
Thanks and Regards,
SouarbhD

Hi,
Use an EVDRE to create your input schedule. You need to have one row with products and 2 columns with time and account. Choose the memberset options as per the requirement. For the accounts, is total calculated with a dimension formula? If yes, then you just need to enter the values for quantity and rate and send the data. The total will be calculated by the system and will be displayed automatically.
Hope this helps.

How to configure 6533 both as input as well as output

Similar Messages

Maybe you are looking for