How to enter ICH5R RAID SETUP MENU?

It is said USE "CTRL+I" enter ICH5R RAID SETUP MENU,but when my computer boot up , there only show press "CTRL+F" for promise 378 raid setup,not "CTRL+I"
even you press "CTRL+I" for many times,when computer is power on,it is nothing happen. If you don't install S-ATA harddisk ,you may not enter ICH5R RAID SETUP MENU? isn't it?
I can use "CTRL+F" enter promise 378 raid setup menu,and how can I enter ICH5R RAID SETUP MENU as the explanatory book said??

In BIOS set S-ATA as RAID, after that you will be able to enter the ICH5R-BIOS with ctrl+I. It appears after the promise BIOS.

Similar Messages

How to enter BIOS and boot menu on Satellite C50-A-1GZ?

Hi,
that is, how can I start the BIOS and the boot menu of my Toshiba C50-A-1GZ?
Thank you

Hi
At first you must perform complete shutdown. How to do this you can read on http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm
Restart your notebook and press F12. There you should find setup options for BIOS settings.

Toshiba P875 S7102 How To Enter The Bios Setup

I have been tring everything to get to the bios screen of the computer. I have tried holding Esc, F1, F2, F10, F12, Delete, but that has not worked. I have found a toshiba manual that said to hold F2 until you see the toshiba logo then release it. Nothing has worked, it just continues to boot to windows 8.
I have searched and searched, this forum and the web, but I have not found anything that has worked to get into the BIOS setup screen.
What is the proper key stroke to get into the bios screen for P875 S7102 laptop?
Thanks.

The "secret" is what you do when shutting down before attempting to access the BIOS. Press the shift key as you click Shutdown. Then on startup, tap F2 to take you to the BIOS screen.
This applies to Toshiba laptops that came PRE-INSTALLED with Windows 8. It does NOT apply to Windows 7 machines or those that were UPGRADED from Windows 7 to Windows 8.
C.B.
Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

How to enter Bios Setup Satellite 4030?

I'm searching for Informations how to enter the Bios Setup.

To enter BIOS settings use ESC button.

How to enter BIOS in e450

Just got this laptop.
Can't enter BIOS. NO F1-F12 keys.
On start up, it just gives Lenovo splash screen then boots windows 8. I am clicking F1 (also tried FN+F1) and nothing happens.
How to enter bios...
Thank you
Solved!
Go to Solution.

Hi jimmyr, welcome to the forum.
Please see this link, and it should answer the question for you.
http://blog.lenovo.com/en/blog/how-to-enter-the-bios-setup-utility-or-boot-menu-with-windows-8-1/
Cheers
DragonRider
I'm DO'ing IT
Lenovo Y470 085525U 2nd generation Intel® Core™ i7-2630QM processor ( 2.00GHz 1333MHz 6MB )
IdeaCentre A520 Intel® Core™ i5-3230M processor ( 2.60GHz 2600MHz 3MB )
YOGA Tablet 2 Pro-1380F
X1 Carbon 2nd Gen (20A8) ThinkPad + T420

Building an editing raid setup with an areca 1220 (8 port)

and here's goes yet another "what should i do raid-wise" question:
gonna build another editing station using some extra parts i have laying around. board is an asus x58 with a intel 980, video will be a nvidia 470. i found my old areca 1220 which i know is a little long in the tooth but would be nice to get some more use out of.
doing a little research i found some articles on what kind of speeds im looking at with it. its obviously not quite what a shiny new card would give me but im hoping with a faster pc and faster drives (articles are from 2007) it'll give decent performance for what i need.
http://www.tomshardware.com/reviews/RAID-SCALING-CHARTS,1635-7.html   (raid 0)
http://www.tomshardware.com/reviews/RAID-SCALING-CHARTS,1662.html (raid 5,6)
ill buy all new drives for this machine (os, media, etc...). i know harm likes his raid 3 thing and im hoping he pops in with his expertise. so my question is how should i go about my complete disk setup from scratch here? type of disks? how many? which raid setup?
My budget is $1000 for the disks. also i mostly edit hd from my mark iii. im using the ml raw hack for about half my shots (and growing). pp cs6, ae cs6, cinema 4d r14 are my progs, though im a cc subscriber and will be integrating the new cc progs into my workflow over the next month or 2 as they work out the bugs/kinks. TIA

With 8 ports available your choices are somewhat limited, but then your budget for the drives is adequate.
You did not mention how much storage space you need, so I will assume 6 or 12 TB net space is enough for your purposes.
If 6 TB is enough, you could look at Seagate Constellation ES 1 TB disks and keep the rest of your budget for the future, if you need 12 TB you could look at HGST Ultrastar or Seagate Constellation 2 TB disks. I would only suggest enterprise drives.
With 8 ports I would configure them as 7 x raid3 or raid5 plus one hot-spare, giving you a net capacity of 6 disks, protection against failure of two disks and a sustained transfer rate of around 0.85 x (N - 1) x T = 0.85 x (7 - 1) x 150 = 765 MB/s. My preference is raid3, but you already know that.
The advantage of this setup is you have double protection in case of disk failure, you have a very high transfer rate and it is easy to administer. Using two arrays reduces performance, reduces protection and is somewhat more cumbersome to administer.

Adding to Raid setup

I did a search, but didn't come up with anything on this.
I currently have a Raid Striping setup with two drives. I picked up another two drives, and now want to change to Mirroring with Striping. When I press F10 for the Raid setup menu, and select the two new drives to go into the array, I get an invalid drive number error, or something like it.
I have not run Fdisk or anything on the new drives.
Is it possible to convert this Raid setup, or do I have to start over and build it new?

Look at the options in nvraidman, which runs in Windows. If your moving from striping to mirrored + striping it might just offer this option to convert, particularly if you have identical drives. Furthermore you should be able to hotwire the new drives in.
Post back and let us know what you do.
Regards
Mick

Tecra 8000 doesn't boot from CD - how to enter the BIOS?

Hello,
i have a 2nd hand tecra 8000.
Now it dont boot from CD? i dont know why... but he question is how to enter on BIOS setup, because is not possible with F2 key.
How to enter on BIOS?
Thanks too much
Francisco
([email protected])

Hi
Please check this Toshiba FAQ document:
How to access to the BIOS Setup - instructions for most models
http://support.toshiba-tro.de/kb0/FAQ6401G1000DR01.htm

6730 (655 Max-FISR) RAID BIOS menu - how to enter?

Hey all,
according to http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=424, this model (6730) should have RAID 0 or 1 support.
But I can't quite figure out anything in the BIOS menu of it that has to do with this. So I installed two Serial ATA hdds onto my motherboard, and they are being detected just fine, no problem at all. So according to the Serial ATA menu, I start installing win2000 and do the F6 and S stuff, loading the drivers for the SATA drives. Then when I get to where it asks me where to install windows too, I get TWO harddrives listed for me to choose from, not one (I'm trying to do RAID 0 btw).
Well coming to think about it, that's logical: I did not set ANYTHING in the BIOS about the drives being in RAID -- I read some guides online on how to install RAID drives -- supposedly you press Ctrl-F to enter the BIOS for RAID controller and set RAID0, RAID1 and those stuff there. Where is this RAID BIOS menu for the MS-6730 motherboard?
most threads I read here, when people talk about doing RAID, most people get through the step "configure the hdds as RAID 0/1" really quickly by a mention with a sentence -- I think that's the part I'm stuck on. Maybe my question should be... how do I enter the RAID BIOS for this motherboard at all? The manuals that came with the mobo don't really have anything on RAID *at all*...
[edit]
btw... I'm new to RAID arrays, so I'm not sure if I'm doing this right. I put my two (identical) hdds one connected to ser1 and one connected to ser2, on the motherboard. is that how you are supposed to do it? they are WD Caviar SATA drives (120gb) btw. jumpers shouldn't be a problem, the WD web site says for a SATA drive, the jumpers are only for power settings, no master/slave things.
Thanks for any help.

http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_sid=CxTASuHg&p_lva=&p_faqid=958&p_created=1050530240&%20p_sp=cF9zcmNoPTEmcF9ncmlkc29ydD0mcF9yb3dfY250PTImcF9zZWFyY2hfdGV4dD1qdW1wZXImcF9zZWFyY2hfdHlwZT00JnB
fcHJvZF9sdmwxPTk1JnBfcHJvZF9sdmwyPX5hbn l_JnBfY2F0X2x2bDE9fmFueX4mcF9zb3J0X2J5P WRmbHQmcF9wYWdlPTE*&p_li=
well assuming you have connected the sata lead and a power connector all i can think is your psu is very poor on the 12v line,how many amps does it give
you might try the jumper bit in the link as well
you will have to paste the full link in

I am trying to setup my new time capsule but it is not working. after entering the airport utility and locating the TC, after I tell the program to continue, the unit just disappear and the setup menu says there is an error. Any idea of what is happening?

I am trying to setup my new time capsule but it is not working. after entering the airport utility and locating the TC, after I tell the program to continue, the unit just disappear from the menu and the setup menu says there is an error. I tried using the wireless connection, and also the cable, but none worked. Any idea of what could be happening?

What are you setting it up as.. join wireless network .. the very worst setup, it will disappear.. reboot the whole network in order modem. router TC.. clients and it will likely reappear.
Tell us what network setup you are using..
If you setup with cable to a computer completely isolated from the network with TC also isolated.. finish the setup of everything you want. .before update.. then plug it into the network. .then restart everything in correct order.. it will work most of the time.

How to enter bios Setup (not the F1 stuff, the splash screen display settings)

So I some how got into a seperate bios setting program by pressing ctrl S when some other bios utility was loading and changed the splash screen display (how long it shows the press enter stuff)
but now I have no idea how to get back into that configruator.
the Manual doesn't mention it, so question, how do I bloody do it?
T430S 2542 btw

Hello
Every time when you switch the notebook ON you can see at the bottom left hand site the short instruction how to enter BIOS settings. In your case you must use F2 button. Please keep it down immediately after switching the notebook ON.
Generally the Toshiba notebooks are delivered with two different BIOS versions (BIOS producer):
- TOSHIBA BIOS: enter using ESC and F1 button
- Phoenix BIOS: enter using F2 button.
According the specification your unit has Phoenix BIOS.
Bye

Raid Setup Guide 865/875 LSR/FIS2R Rev 1.04

On-Board Raid Setup MSI 865PE/875P
Revision History
Revision 1.0 (January 2004)
- Original Raid Article
Revision 1.01 (February 2004)
- Reformatted text and fixed spelling/grammar
Revision 1.02 (October 2004)
- Added warnings to temporarily disconnect ALL drives including Zip drives during formatting Raid drives for WinXP.
Revision 1.03 (October 2005)
- Reformatted text and added links to download Promise/Intel Raid floppies if user is missing them.
Revision1.04 (February 2006)
- Minor BB reformatting
Intro
Equipment List For Tests
Description of Tests
Pre-Raid Setup Bios Tweaks
Raid Setup On Promise Controller
Raid Setup On Intel Controller
--->Intel- Migrating from single SATA to Full Raid Array
Intro
This guide is intended to help people configure their Bios and setup Windows for Raid using the Intel ICH5R controller and the Promise FastTrak 378 controller. Although all the tests were done using Raid-0 the methods described should be virtually identical to setting up Raid-1 provided the user is aware of the fundamental differences between the two. It should be useful for anyone with an MSI 865PE/875P chipset on motherboards with LSR and FIS2R suffixes. Before continuing, please read the FAQ thread posted by Maesus and the Raid manual(s) that came with your motherboard. There's also some good info regarding Raid Here and Here and Here
Keep in mind this guide is intended as a reference to help you. It is not a manual. I do not work for MSI and my equipment and time are limited. You will have different equipment and different versions of software.
All the data below is based on tests that I ran and I tried to avoid using any theory that I did not test. If you feel I’ve missed something obvious or if you have something you feel should be added to make this guide clearer or simpler, please PM me with your thoughts. If you have a specific problem that this guide does not help you with, post a detailed thread in the forum on the main page.
Equipment List For Tests
MSI 875P FIS2R Motherboard
Bios 1.8
Enermax EG365P-VE (350w) PSU
P4 2.6c CPU
Kingston KHX-3200A2 2x512MB Memory
Radeon 9800Pro AIW Video Card
WD 400JB 40GB/8MB cache IDE Hdd
2-Seagate 80GB 7200.7 SATA Hdd's
Liteon 52x32x52 CDRW
Floppy Drive
Tests
Generally, tests were as follows:
Configure 2 SATA on Promise controller(serial3&4) as Raid0 and install WindowsXP Home SP1a on Raid
Configure 2 SATA on Promise controller(serial3&4) as Raid0 and add Raid to an existing WindowsXP installation on IDE drive(IDE1)
Configure 2 SATA on Intel Raid controller(serial1&2) as Raid0 and install WindowsXP Home SP1a on Raid
Configure 2 SATA on Intel Raid controller(serial1&2) as Raid0 and add Raid to an existing WindowsXP installation on IDE drive(IDE1)
Configure 1 SATA on Intel Raid controller(serial1) and install WindowsXP Home SP1a on it. Then add 2nd SATA on Intel Raid controller(serial2) and migrate to Raid0 using Intel Application Accelerator-Raid edition.
IDE drive used in these tests was pre-installed with a fresh copy of WinXP Home SP1a using default settings and the following drivers all from MSI setup CD and Raid Floppy Disks that came with motherboard:
Intel INF files - version 1002
Gigabit Lan drivers - 7.0.37.0
SoundMax drivers - 5.12.1.3538
Catalyst 3.7 & Multimedia Center drivers from standard ATI CD came with video card.
Pre-Raid BIOS Tweaks
Before I continue, I'd like to point out a few changes from the defaults that I alway make to Bios before I attempt a WinXP install or hardware change. I can't guarantee that they all apply to you but none should make things worse. If anything differs from a setting that you feel is fixing another problem you're having, by all means leave at your prefferred setting. Anything related to performance and overclocking can be raised again AFTER the Raid is all setup and everything is running smoothly.
Standard Cmos Features
The only thing I change here is to enable "32bit transfer mode" whenever I connect new devices to the Intel IDE controller.
Note: Devices attached to the Promise controller and the Intel Raid(when it is enabled) will NOT appear in the standard Cmos page
Advanced Bios Features
Everything on defaults is usually fine except I always change the following for WinXP:
APIC ACPI SCI IRQ - Enabled
Boot Device select is also on this page and you'll be changing it after all the hardware is setup; more later.
Advanced Cipset Features
Confirm that the memory timing "by SPD" is enabled
PNP/PCI Configurations
Clear NVRam option I always set to "YES" before the first boot after making hardware changes. I'm not sure how important this is but I understand that's what you're supposed to do. I believe it forces the motherboard to detect hardware changes. It reverts to "NO" after the reboot.
PCI/IDE Busmaster set to "enabled" to speed things up outside of Windows.
Integrated Peripherals (Before Raid for most flexibilty)
Onboard Promise IDE - Disabled if you have nothing attached to IDE3 and Serial 3&4
ON-Chip IDE Configuration:
Native Mode (Supported by WinXP- Allows all devices connected to IDE 1&2 and Serial 1&2 to be detected)
SATA Only or PATA Only (select the one that you boot XP with)
Keep SATA Active - Yes (if option available)
Keep PATA Active - Yes (if option available)
PATA Channel selection - Both (if option available)
Configure SATA as Raid - No (if option available)
Leave other settings here at default
Note: Some older Bios versions may appear different than above
Frequency/Voltage Control
Dynamic Overclocking - Disabled
Performance Mode - Slow
Dram Frequency - Auto
Adjust CPU Bus - 201 (for "c" type cpu's)
DDR Voltage - 2.65 (minimum for Dual-Channel Mem stability)
AGP Voltage - 1.55
Note: some features above may not appear with your Bios
Note: performance & overclocking features can be increased again AFTER the Raid array has been setup and is stable with Windows.
Raid On Promise Controller
This procedure should work for anyone adding a Raid array to a system already having XP installed on another drive on the Intel controller or intending to install Windows XP on the new Raid array.
Note: IDE 3 and Serial 3&4 connectors are controlled by the Promise controller.
Note: It is possible to setup Raid arrays using 2 IDE drives on IDE3 or even 2 SATA & 2 IDE drives. I only tested 2 SATA drives on Serial 3&4 connectors.
Note: It is possible to setup Raid 0+1 using 2 IDE drives on IDE3 and 2 SATA drives on Serial 3&4. See HERE for a related thread.
Note: It is possible to setup SATA or IDE drives on the Promise controller as separate drives NOT using Raid but I did not test this. See your manual.
- Attach the SATA drives to Serial 3&4 connectors and ensure that both power and data cables are securely connected. Most SATA drives do NOT need any changes to default jumper positions if any(check Hdd installation instructions).
- Boot into Bios
Integrated Peripherals:
Set Onboard Promise IDE - As Raid
- Save and reboot computer
- Use control-F keys during the boot(when prompted-goes by quickly) to enter the Promise Raid Bios.
Note: You will only be able to enter the promise Bios if you have set the Promise controller to "As Raid" AND there are devices connected and detected by the Promise Bios.
- Use the menus to configure the Raid for your preferences.
Note: I can't say which settings you should use for creating the Raid. It depends on many things. Do some research.
- After saving the Raid array, reboot to Bios.(you should see the configured array for a second or two during the post and it should be "functional")
- In Advanced bios Features>>Boot Device Select:
Set the order you prefer to boot from
- If you already have XP installed on another drive and are just adding the Raid for an extra drive, Ensure that the list is still appropriate and includes your XP drive.
- If you will be installing XP on the new Raid, make sure the new Raid array is in the boot list and any other hard drives are NOT.
Note: Typically, I put the disk with XP first and use F11 key during post to boot from another device. This is not required though.
- Save bios
Important!: If you are installing XP on the new Raid array, you should now shutdown and either disconnect or disable any other drives connected until AFTER XP is installed. This includes USB/Zip drives.(See "Bugs" below).
If Installing XP On The New Raid Array(others skip to below):
- Boot from the Windows XP Setup CD and use F6 key when prompted(at the beginning).
- Follow prompts to load the WinXP Promise FastTrack 376/378 Controller from the floppy that came with motherboard(If Required Download Floppy Here). There are a number of different choices on the floppy. PICK THE RIGHT ONE.
Note: if using Win2K with the floppy, you can scroll down to get more driver options on this screen. It's not readily apparent on the screen.
- Continue setup and Windows should now show you the new Raid array as a single drive available to install to. If it shows other drives that you have connected, re-read the "important" note above and the related section on "Bugs" below.
- When XP setup makes its first re-boot, make sure the floppy has been removed or depending on your settings it may give you a scary moment. Yes I did this(tries to boot from floppy).
- After XP is up and running, you can re-connect/re-enable any drives you disconnected earlier. If they have been formatted, they should show up immediately and be assigned letters after your CD/DVD drives.
- You can also install the Promise Array Manager software(from MSI CD utilities tab or download) which adds some array management settings.
If XP Already Installed On Another Drive(and you're just adding the Raid as an extra storage disk):
- Boot into WindowsXP.
- As Windows starts, it should detect a new Raid device and offer to install drivers.
- Select Cancel. It will tell you that it was unable to install new device. If you want you can confirm the new device is present by checking Windows device Manager. It should show the new device with a yellow exclamation mark beside it since the drivers aren't installed yet.
- Download the appropriate drivers or use the MSI CD that came with motherboard.
Note: The MSI CD detects devices connected and shows available drivers/utilities depending on what it sees. You might not have seen the Promise drivers when using the CD before but now that you have a Raid array connected to it, the drivers will be availble from the MSI setup CD.
- Install the drivers and re-boot
- Device Manager should now show the Raid properly identified by XP.
- If the Raid array was not previously formatted, you can now use Windows Disk Manager (Start > Run and type diskmgmt.msc) to Initialize and then format the Raid array.
- The Raid array should now show in Windows Explorer with it's own drive letter.
Bugs/Surprises
- Trying to install WinXP on the Promise Raid while my IDE drive was connected to the Intel IDE connector resulted in Windows installing boot files to the IDE drive and the rest on the Raid drives. This was especially bad since I had another installation of XP on the IDE drive which was overwritten. The work-around was to disable the IDE drive until AFTER XP was setup on the Raid array.
Update: There have been a few posts on the forum since I wrote this guide where people installing XP have had problems similar to the one above with USB/Zip drives connected so i am adding them to the list of drives to disconnect while installing XP.
- When setting "Boot Device Select", if I selected "NO" for "boot from other devices", the motherboard would ignore my selection and still boot from other devices if the ones in the list were unusable.
- Be gentle with SATA connectors on the motherboard. They can stand firm downward pressure but not a lot of side-to-side pressure.
Raid On Intel Controller
This procedure should work for anyone adding 2 SATA hard drives for a Raid array on a system already having XP installed on another drive or intending to install XP on the new Raid array.
Note: IDE 1&2 and Serial 1&2 connectors are controlled by the Intel ICH5R controller. Only Serial 1&2 can be configured for Raid arrays.
You can also install a single SATA drive and configure the system for Raid BEFORE installing XP on this drive if you intend to add another SATA drive later to form a Raid array. This method was also tested. I will refer to this for the rest of the thread as the Raid-Ready Method.
Note: If you install WinXP on a single SATA drive without enabling Raid and loading Raid drivers, you will NOT be able to migrate the XP disk to a Raid array at a later date. Reinstalling XP would be required.
Note: There is no performance advantage to having a single drive with Raid enabled. But doing so makes the disk Raid-ready and XP reinstall unnecessary.
- Attach the SATA drive(s) to Serial 1&2 connectors and ensure that both power and data cables are securely connected. Most SATA drives do NOT need any changes to default jumper positions if any(check Hdd installation instructions).
- Boot into Bios
- In "Integrated Peripherals>>On-Chip IDE Configuration" set:
Native Mode (Supported by WinXP- Allows all devices connected to IDE 1&2 and Serial 1&2 to be detected)
SATA Only (Even if you will be booting XP from a PATA drive)
Keep PATA Active - Yes
PATA Channel selection - Both
Configure SATA as Raid - Yes
Leave other settings here at default
Note: Some older Bios versions may appear different than above.
- Save Bios and reboot computer
- Use control-I keys during post(when prompted-goes by quickly) to enter the Intel Raid Bios Utility.
Note: If you are using the single SATA Raid-Ready Method, you can skip the steps involving the Intel Raid utility. Go to the step for setting Boot device select in main Bios.
Note: You will only be able to enter the Intel Raid Bios if you have set the "Configure SATA as Raid" option to "YES" AND there are devices connected and detected by the Intel Raid Bios.
- Use the menus to configure the Raid for your preferences.
Note: I can't say which settings you should use for creating the Raid. It depends on many things. The Intel utility does describe the different options well though.
- After saving the Raid array, reboot to Bios.(you should see the configured array for a second or two during the post and it should be "functional")
- In Advanced bios Features>>Boot Device Select:
Set the order you prefer to boot from;
If you already have XP installed on another drive and are just adding the Raid for an extra drive, Ensure that the list is still appropriate and includes your XP drive.
If you will be installing XP on the new Raid or using Raid-Ready Method, make sure the new Raid array or raid-ready drive is in the boot list and any other hard drives are NOT.
Note: Typically, I put the disk with XP first and use F11 key during post to boot from another device. This is not required though.
- Save bios
Important!: If you are installing XP on the new Raid array or using the Raid-Ready Method, you should now shutdown and either disconnect or disable any other hard drives connected until AFTER XP is installed. This includes Zip/USB drives. (See "Bugs" below).
If Installing XP On The New Raid Array Or Using Raid-Ready Method(others skip to below):
- Boot from the Windows XP Setup CD and use F6 key when prompted(at the beginning).
- Follow prompts to load the IAA Raid Driver for ICH5R (If Required Download Floppy Here) from the floppy that came with motherboard. I only had 1 driver to choose from on my floppy but if you have more, CHOOSE THE RIGHT ONE!
- Continue and Windows Setup should now show you the new Raid array or Raid Ready drive as a single drive available to install to. If it shows other drives that you have connected, re-read the "important" note above and the related section on "Bugs" below.
- When XP setup makes its first re-boot, make sure the floppy has been removed or depending on your settings it may give you a scary moment. Yes I did this(tries to boot from floppy).
- After XP is up and running and INF files and other important drivers installed, you can re-connect/re-enable any hard drives you disconnected earlier. If they have been formatted, they should show up immediately and be assigned letters after your CD/DVD drives.
- You can also install the Intel IAA-Raid Program(from MSI CD utilities tab or download) which gives some info and adds the array management settings(Not many. Just the enable/disable cache setting and the migrate to raid option).
If XP Already Installed On Another Drive(and you're just adding the Raid as an extra storage disk):
- Boot into WindowsXP.
- As Windows starts, it should detect a new Raid device and offer to install drivers. Select Cancel. It will tell you that it was unable to install new device. If you want you can confirm the new device is present by checking Windows device Manager. It should show the new device with a yellow exclamation mark beside it since the drivers aren't installed yet.
- Download the appropriate drivers or use the MSI CD that came with motherboard.
Note: The MSI CD detects devices connected and shows available drivers/utilities depending on what it sees. You might not have seen the IAA Raid drivers when using the CD before but now that you have a Raid array connected to it, the drivers will be availble from the MSI setup CD.
- Install the drivers and re-boot
Note: If the IAA Raid program detects that the Raid controller is not enabled or no device is present, it will NOT allow you to install the drivers/utility.
- Using Windows Device Manager should now show the Raid device properly with no problems.
- If the Raid array has not been formatted, you can now use Windows Disk Manager (Start > Run and type diskmgmt.msc) to Initialize and then format the Raid array.
- The new drive should now appear in Windows Explorer with it's own drive letter.
Bugs/Surprises
- Trying to install WinXP on the Promise Raid while my IDE drive was connected to the Intel IDE connector resulted in Windows installing boot files to the IDE drive and the rest on the Raid drives. This was especially bad since I had another installation of XP on the IDE drive which was overwritten. The work-around was to disable the IDE drive until AFTER XP was setup on the Raid array. It is safe to assume this can occur with the Intel controller as well since I believe the problem occurs because of how WinXP setup addresses the hard drives.
Update: There have been a few posts on the forum since I wrote this guide where people installing XP have had problems similar to the one above with USB/Zip drives connected so i am adding them to the list of drives to disconnect while installing XP.
- Be gentle with SATA connectors on the motherboard. They can stand firm downward pressure but not a lot of side-to-side pressure.
Migrating XP System Disk To Raid On Raid-Ready System
This part describes how to use the Intel Application Accelerator-Raid edition to migrate an existing WinXP system disk (1-SATA) to a 2-SATA Raid array.
This procedure is actually very well documented in the last part of the Intel SATA Raid manual that ships with the motherboard but I thought I’d add it to make this thread more complete.
Please note that to use this feature of the Intel raid software the disk you are migrating FROM must have been made Raid-Ready as described above. Basically, this means that Raid should have been enabled in the Bios and the drivers installed from floppy during the WinXP install.
Note: I tested this by migrating to a Raid0 array but Raid1 should work also if the latest Bios and version of Intel-Raid application used.
- Open the Intel Application Accelerator Raid utility.
- With the “Raid” tab window open, right-click on “Raid volume” and select “Create from Existing Disk” as seen below.
- Follow the next several steps to choose the type of Raid array and the strip size.
Note: 64kb strip size is good for general purpose and 128kb best for most desktops and work stations according to Intel. Anything smaller is for specialized purposes. You should research this a little because you can’t change it after easily.
- After configuring the array for your preferences, you will face a couple of warnings telling you that “All data will be deleted from the Raid-controlled drive(s) and is unrecoverable” and ask if you want to continue. Obviously all data(if any) on the new drive you’re adding will be lost but the OS and other data on the disk you’re migrating FROM will be striped to the new array and will remain intact.
Note: Any complex disk procedure such as this carries the risk of losing data. A backup of the disk is important BEFORE beginning the migration process. Don't say I didn't warn you.
- The migration process can take a long time. You should see the window below during the operation.
Note: With just a default WinXP installation, migrating to 2-80Gb drives took about an hour for me.
- After the migration is complete, you will be prompted to re-boot to complete the process.
- During the reboot, as the Intel Bios comes up for a couple of seconds(don’t blink) you will see the 2 drives configured as an array and they will be listed as “functional”.
- After the reboot, you should have a fully functional Raid array with 2 SATA drives and all data from the single drive will have been striped or mirrored into the second one. Check Windows Disk manager(Start > Run and type diskmgmt.msc) to see the status of the new drive. See bugs/surprises below.
Bugs/Surprises
The only problem I had with this test came in the form of a small surprise after everything was completed and the computer had rebooted. Although the Intel Application Accelerator showed everything functioning normally, Windows explorer showed my Raid drive as 74Gb in size instead of the 150Gb or so that I expected. After checking Windows disk Manager (Start > Run and type diskmgmt.msc), I found that the missing GB’s were in fact there but were unformatted. Unfortunately, Disk Manager does not seem to allow merging or extending partitions so I ended up using Partition Magic 8 to format the empty space and merge it with the rest of the partition. This seemed to work fine and I ended up with a single 150Gb drive showing up in Windows Explorer. I also briefly tested the performance to confirm that it was operating as a Raid array.
I know there is a utility for Win2K called DiskPart.exe that is run from command console to extend NTFS partitions but if anyone knows of an easier way or a FREE utility that will format/merge NTFS partitions that they have confirmed works, please PM me so that I can include a reference to it here.
All the data above is based on tests that I ran and I tried to avoid using any theory that I did not test. If you feel I’ve missed something obvious or if you have something you feel should be added to make this guide clearer or simpler, please PM me with your thoughts. If you have a specific problem that this guide does not help you with, post a detailed thread in the forum on the main page.
Vango44

Great work vango44!
Here are some RAID performance statistics I gathered while testing RAID on my system. The testing software was Winbench 99. The hard drives tested were new Seagate ST380013AS drives, formatted NTFS. Winbench was running on a third drive that is not included in the tests and should not affect the results.
The drives were reformatted between tests and chkdsk'ed to try and keep things "apples to apples".
No hardware or software changes other than the RAID setup/connections were made between tests.
Higher numbers mean better performance.
I also ran the same tests on the newish WD Raptor 10K drives:
I couldn't stand all the noise the Raptors made, so I returned them.
On my motherboard:
SATA 1 & 2 = Intel RAID controller
SATA 3 & 4 = Promise RAID controller
If the test title does not include "RAID", then it was a single drive test.
Unfortunately, I don't have a spreadsheet version of the above stats. Otherwise I'd create nice bar charts for us and it's would be easier to deduce performance.
Perhaps some kind reader will OCR the pictures, put them into Excel, and make some nice bar charts for us?
Hope the info helps.

Raid Setup 890FXa

This is the first time I have tried to setup RAID or build a computer from scratch. I have been swapping parts for years but never built a system from scratch. My troubles are with setting up a striped RAID for the OS to install on. I have tried loading the RAID controller from the MSI boot disk which came with the board and a USB stick. I have tried loading the RAID drivers both before and after installing the OS. I have been unable to setup the RAID Controller. I have tried launching it before OS install, while in OS install and after install.
I can load Win7 and use software RAID but wanted to have the drives as boot drives with the OS installed on them for faster application access. I have searched the Internet high and low and nothing I do gives me the options of hitting Control F to enter the RAID Option ROM Utility. Inside the BIOS the only option for RAID is IDE.
Is there anyone on here who can give an 'idiots buid to setting up raid' on this board with a Windows 7 64-bit OS?

Me Again,
Making the changes in the sub-menu allowed me to setup the RAID array. Unfortunately, I am now experiencing more joyous setbacks. After setting everything to RAID I am receiving an Error msg during Win7 install.
I previously used the same OS install disk/hard drives/DVD player(s)/entire system to install win-7 64-bit on the same equipment without this error. Everything installs fine without RAID as boot array.
The current error occurs during Win-7 installation and states:
"A required cd/dvd drive device driver is missing. If you have a driver floppy disk, cd, dvd, or usb flash drive, please insert it now."
This error never occurred when I used the same equipment. I have searched for downloadable DVD player drivers for the drives but could not find drivers for either DVD player on-line (only firware updates). I also attempted to install specify the RAID Drivers (from MSI.com and MSI install disk/USB) and the install will not recognize the RAID drivers (I assume because it is looking for DVD drivers).
Do you have any helpful ideas as to what might assist with install to pass this error message?
Thanks in advance.

Bios and SATA Raid setup nightmares

Three manuals with this mobo and I just can't get it set up.
I have the 865PE Neo2-FIS2R, an Intel 3.0GHZ Northwood processor, a pair of 256 memory chips configured as dual channel. A pair of SATA drives are on the Intel ports. The IDE has four devices connected, a HDD, Zip drive, and a pair of CDs. All of the hardware, jumpers, cables seem to be working fine.
My goal was to have a SATA Raid 0 setup, with the spare drive for backup and misc storage. CD's and Zip for input, burning, etc.
After everything was connected I booted Win XP Pro from the CD, did the F6 thing and installed the drivers for both Intel and Promise (Fastrack and drivers). Setting up the bios "Integrated Peripherals" was a real problem and the book very little help, but I finally got the system to recognize things so I could format and boot and install the OS. I did the Control-I thing and configured the Raid drives (at least I think). So far, so good.
After the OS was installed, SP1 added, etc. I got ready to configure the Raid. The CD does not come up with the screen shown in the manual. But I did find the Intel IAA RAID Edition in a folder. Running it results in an error message saying that the software does not support this chipset. Downloading similar drivers for both Promise and Intel always dead-ends the same way.
What I'm leaving out are the--literally--hours of time I've spent trying to get the devices configured right in the Bios' "Integrated Peripherals." I have no idea what I'm doing and the book is no help. But the devices are all there now and the OS runs fine (but not as a Raid 0 set up).
The book says I can migrate this configuration to a Raid volume. How, when I get that error message?
And another thing. Can I use the Promise IDE (PATA) port for a single drive? It's the only place on the mobo where ATA 133 is supported.
I think I'm in a world of trouble here. Don't know squat about these complex bios setups. Sorry this is so long.
ardi

OK, I actually went down to the basement and dug out the ICH5R Raid Manual. Basically it says in order to take advantage of the ability to migrate later on, you have to set Raid in Bios B4 loading Windows and install Raid driver with Windows setup. If you've already got Windows installed on 1 disk and had Bios set to"SATA as Raid- NO", you're out of luck.
Here's the exerpt from the manual:
Quote
The Intel Application Accelerator RAID Edition offers the flexibility to
upgrade from a single Serial ATA (SATA) hard drive to a two drive RAID 0
configuration when an additional SATA hard drive is added to the system.
This process will create a new RAID volume from an existing disk. However,
several important steps must be followed at the time the system is first
configured in order to take advantage of RAID when upgrading to a second
SATA hard drive:
1. BIOS must be configured for RAID before installing Windows* XP
on the single SATA hard drive.
2. Install the Intel Application Accelerator RAID driver during Windows
Setup.
3. Install the Intel Application Accelerator RAID Edition after the
operating system is installed.
Maybe someone knows a work-around?

Reformatting external drive to Mac OS Extended but maintaining RAID setup

Hi again,
I am considering taking the leap finance-wise and purchasing [this external drive|http://www.amazon.com/Western-Digital-WDH2Q20000N-Studio-Interface/dp/B00 16P7H3Q/ref=cmcr_pr_producttop]. It comes pre-formatted to HFS+ or something, so I guess I will need to reformat it to Mac OS Extended to use it with FCE.
So here are the questions:
*1. Would it make more sense to use it in RAID 0 mode for faster speed, or RAID 1 mode to keep a safer backup of my files?*
*2. Would reformatting it to Mac OS Extended for use with FCE still allow it to use normal RAID abilities?*
I realize this is not the right forum for posting this, but I thought someone here might be knowledgable about backup in general and how to best format an external drive for use with FCE, while maintaining the ability to have a "mirrored" RAID setup. Any thoughts?
Thanks in advance,
Sasha
Message was edited by: skalicki`

So just one more question because I'm pretty new to this whole RAID thing:
Say I formatted the drive to RAID 1 so in theory I have 1TB of space that is "mirrored" over to the other external drive.
*When I ingest my footage, will copies be stored to both drives, so if one fails, I will still have my media?*
I gathered this was the idea but didn't know how it works with FCE.

How to enter ICH5R RAID SETUP MENU?

Similar Messages

Maybe you are looking for