How to get 6bg Sata speeds on Big Bang MSI

How in the world do I get my SSD to 6gb Sata speeds? I have it hooked up to the white cord in Sata 8 which is the Marvell controller. I've searched in the bios to no avail. Can anyone please provide a detailed step-by-step procedure for a noob to do this? Thank you.

What SSD do you have? You must provide adequate information if want decent helpful answers to any questions you have. >> Posting Guide <<
Have you benchmark/tested it , with what and what were the results? I don't think you will get 6Gb/sec with current drives.
One example mentioned here:
"Micron has announced the "industry's fastest" SSD, with about 50% better data transfer speeds than today's best consumer-grade flash drives. The company's RealSSD C300 is the first to embrace the SATA 6Gb/s and Open NAND Flash Interface (ONFI) 2.1 specifications, allowing it to deliver sequential read speeds of up to 355MB/s and sequential write speeds of up to 215MB/s."

Similar Messages

How to get the last version of flash in MSI format automatically?

How to get the last version of flash in MSI format automatically?
Roberto Neigenfind
Bravo Tecnologia
www.bravotecnologia.com.br

Hi Barbara,
Flash Professional CS5.5 is a 32-bit application which can be installed on computers with either 32-bit or 64-bit operating systems.
You can purchase this by Adobe's backward Licensing policy :
" Adobe allows program members to order a current-version license but use a prior version. These members can contact Adobe Customer Service to request a serial number for the earlier version if they do not already have one. Prior-version software is available via ESD and can be purchased through standard resellers. The program member must follow all guidelines of the current-version EULA. "
Please check the doc : http://www.adobe.com/volume-licensing/policies.html

How to get 802.11n speed for Apple TV?

I installed my first Apple TV yesterday. Great stuff!
My iTunes movie library is on a Core 2 Duo MacBook Pro. I have not yet used the AirPort Extreme 802.11n Enabler on this MacBook, since I just found out it exists. If I use it, can I utilize 802.11n sync speeds with the Apple TV? How?
My AirPort network uses only an "old" 802.11g AirPort Extreme base station, not the "new" AirPort Extreme base station with 802.11n.
I have three 802.11g AirPort Express base stations on my network, mainly for using AirTunes.
My iMac connects to my wireless network using 802.11g, and I don't think the 802.11n Enabler works with it.
My cable modem current connects to my Airport Extreme (802.11g) base station via Ethernet.
I understand I can get a new AirPort Extreme 802.11n base station to replace the 802.11g one, and that would let me use the higher 802.11n speed from the MacBook to the Apple TV. It would also allow (unless I misunderstand) all my 802.11g devices to access the network at the lower speeds they are capable of. Correct?
I also understand there is something called a "dual band network" that involves using both base station types in one large network, but I don't know what the advantage of doing that would be, compared with just replacing the old base station. Can someone fill me in on that?
And, is there any way to get 802.11n speeds from the MacBook Pro to the Apple TV without getting an 802.11n base station?
Thanks in advance.

If I use it, can I utilize 802.11n sync speeds with the Apple TV? How?
And, is there any way to get 802.11n speeds from the MacBook Pro to the Apple TV without getting an 802.11n base station?
No. Unless you set up an adhoc network between your Mac and the Apple TV.
I understand I can get a new AirPort Extreme 802.11n base > station to replace the 802.11g one, and that would let me > use the higher 802.11n speed from the MacBook to the Apple > TV.
Yes, it would.
It would also allow (unless I misunderstand) all my 802.11g devices to access the network at the lower speeds they are capable of. Correct?
If you set things up this way, then I believe you wont be able to use wideband mode on the AEBSn. Your AEBSn will be opperating in mixed mode and its 802.11n performance will be degraded. The best set up would be to keep your old router to service the G only devices, and have your new AEBSn service the N capable devices. This would allow you to take full advantage of the performance increase provided by 802.11n capable devices.
Message was edited by: ctomer

How to get majority of speed on one device

I have multiple devices on the e1200 router and i am trying to figure out how to get majority of the speed on one device.
And give all the other devices low speeds.
help?
Solved!
Go to Solution.

Hi Capo202, you can try to use the QoS settings of the router. Just access the setup page of the router and look for this page http://ui.linksys.com/files/E1200/2.0.00/qos.htm. Hope this can help you.

How to get rid of D.O.T tab&MSI info tab?

Hiya people
Does anyone have any idea,s on how to get rid of the msi info and DOT tabs in the display properties
I,ve looked thru the forums and someone said the msi drivers introduce a new dll to the win/system32 folder and the only way is to format the drive ,i don,t wonna do that as i,ve just recently formatted.
Its not a major fault or anything as i think they are harmless, they just annoy me being there,i prefer coolbits for my overclocking.
Any idea,s would be greatly appreciated thanks
AthlonXP2800+ Bartoncore @2083MHZ WinXP pro sp1
Epox NForce2 8RDA+ mobo
2x512MB dualchannel enabled
MSI NX6800GT 256MB videocard @400core 1100mem forceware 65.73beta
Audigy Soundcard + 5.1 soundsystem
Sony Trinitron 21inch FlatDisplay

Quote
Originally posted by CDM
Well Congrats on answering your own question with in 16 minutes

How to configure the bios of the big bang marshal p67 (help)

Good afternoon people I'm new here, I hope to be posting in the correct forum, and come on, I recently bought a Big Bang Marshal P67 B3, I'm using a vcore [email protected] to 1:42 daily and a kit of 2200MHz 2x2GB Gskill PIS, but whenever I play the machine locks up and has the blue screen, I'd love your help on all the settings I need to do to leave my bios over 100% stable.
Thanks in advance for help.

Quote from: HU16E on 04-August-11, 11:28:03
Right click 'Computer', then left click 'Properties', 'Advanced system settings', 'Startup and Recovery' 'Settings', uncheck 'Automatically resart'.
Disabled.
Thanks buddy, now I found.
I'll take and post all the screens of my bios, if possible tell me if you configured everything right or if I need to change something ok.
Every time I try to run prime95 linx or just going to play, does not take long to see this screen.

How to get bandwidth / internet speed in my application ?

Hi,
I am using iPad 3 and ios 5.1
I want to know the bandwidth used by my application (or the internet speed) and display it , as my application deals with downloading of images.
Please guide me ......
Thanks

Thanks for the reply ...
Is there any api or third party library ,we can directly use for finding bandwidth info.
Thanks

Satellite A300 - After Windows 7 installation how to get factory sate back?

I have recently installed windows 7 on my laptop and now I want to remove them and restore my computer to its factory state.
When I enter the "advanced boot menu" I select "repair my computer", then there is a menu from which I select "repair...something". Then it shows up a message which says that there is nothing wrong with my computer and that's where all end.
Any ideas???
Thank you

Hi
Did you not create the Toshiba recovery disk as yet?
I think you didnt read the user manual because there you can also find a lot of informations about this.
The Toshiba recovery disk you can burn using the Toshiba recovery disk creator. This tool is preinstalled on every Toshiba notebook but on another OS like Windows 7 its not possible.
Normally after the first start when you bought the notebook you get the following message (recovery reminder):
+Important INFORMATION+
+your system is equipped with hard disk recovery system. if you need to repair+
+your computer by restoring it to original factory state, you can do it directly+
+from harddisk (press F8 when you boot your computer, choose "Repair your computer"+
+and follow the menue instructions) or create a bootable Recovery Disc Medium for this purpose.+
+Toshiba recommends you to create Recovery Disc Medium using the "Toshiba Recovery Disc Creator" to ensure+
+hat you are able to restore your computer to the original factory installed state, even if your computer+
+gets seriously damaged+
However, now its too late and you have to order a new recovery disk from Toshiba directly:
https://backupmedia.toshiba.eu/landing.aspx
Bye

How to get slow playback speed with video

Hi. Newbie to the forums. hope you can help.
Can I put a control in flash that allows users to alter the
playback speed of a video clip? I am making a tutorial (with sound)
and I want the students to be able to run the video in slow motion
and then gradually increase the speed as they become more
confident.
Any ideas?
Regards
Matthew

Thanks. I checked out the web site, and although it only refers to FCP, I assume "Film Effects" is compatible with FCE HD v3 as well.
I appreciate the info.
Gary

How to get higher clock speeds with OC Genie?

I am 100% new to overclocking and I just built my new pc...
Bios version 1.5
Intel I7 860 Cooled with Corsair H50 Push-Pull
MSI P55 GD65 non USB3
2x2gb Corsair XMS3 DDR3 1600(Running at 1333 for some reason)
Zotac Geforce 9800GTX+ 512mb
Antec Trupower Trio 550w
2x WD Caviar Blue 160gb in Raid0
When I hit the OC Genie button it gives me 3.54GHz. Is there anyway to get to 4.0GHz with my setup.
Have not changed any settings myself all was done with the OC Genie button
My temps are around 42' with fans on lowest settings

Quote from: Bernhard on 01-May-11, 15:25:22
OK, so you are able to set your CPU voltage manually. You need to consider that the auto voltages will compensate only up to a certain OC level, after which the user usually has to do manual adjustments. This auto compensation differs for each hardware combination. As HU16E suggested, try low VDroop and see if it helps. The other alternative is a BIOS flash, or manual voltage settings.
I tried low vdroop but it didn´t make any difference. But it´s ok, i can set the vcore manually but i was just investigating if i could get the best of both worlds with the powersavings auto vcore offers during idle

How to Reset the Sata Link Controller for Full Sata 3 speeds on an OCZ Agility 3

So I purchased a new OCZ Agility 3 drive, installed it into the main bay of my 2012 Macbook Pro, and the drive was running at half speed. I called OCZ and spoke to the guys about how to resolve this issue, they were very knowledgeable, but they had no ideas how to make thier Linux Live Tool work on the Mac, which gives us the ability to reset the controller. Here's what I did to get the full speeds out of my OCZ Agility 3.
- You will need a Windows computer, or the ability to create and install Windows on a Bootcamp partition on your Mac.
- Thumb Drive
- Lots of Patience
1. Open Disk Utility and create one partition on your thumb drive under MS-DOS Fat 32. Click the Options tab and select “Master Boot Record.”
2. Go to the OCZ forum and download the older Linux Live Tool version: OCZ_Tools_316-old.zip. From my experience, the newer version doesn’t work on the 2012 Macbook Pro.
3.Download the “Universal USB Installer” for Windows, and follow the steps to install the ISO to your Thumb Drive using the instructions located on the OCZ Forum. http://www.ocztechnologyforum.com/forum/showthread.php?99275-NEW!-Bootable-Linux -based-tools-for-OCZ-SSD-s&p=714047&viewfull=1#post714047
4. Once the ISO is successfully copied to the Thumb Drive, insert the USB stick into your Mac with the OCZ SSD installed in the Main Bay, Power On, and hold down the “Option” key. You should see a yellow hard disk icon that says “Windows,” select it and press enter.
5. Once the OCZ Tool loads up, click the “Green Arrows” to put the drive into Sata II mode. Shutdown the computer, power on, and check the System Profiler. The drive should be running at Sata II speeds.
6. Shutdown the computer and boot into the OCZ Tool, and click on the “Red Arrows.” This will reset the controller to its default mode of Sata III (Sata 6 Mode).
7. Check the speed of the drive using the disk speed test of your choice. The drive should now be running at full speed.
The biggest accomplishment here was actually getting the OCZ Linux Live Tool to load on a 2012 Macbook Pro. The newer version of the tool doesnt support the USB 3.0 drivers, so you loose the funtion of your trackpad and keyboard or bluetooth keyboard and mouse.
**Note: Black Magic Disk Speed Test Version 2.0 may give you lower numbers than expected due to the compression method in testing the drive. I would prefer using XBench or Disk Speed Test Version 1.0**
***Here's a link to a thread that explains how to properly install your OS onto the drive. If not done correctly, this can also cripple the speed of the drive.***
Drive Preparation
https://discussions.apple.com/thread/3381208?start=0&tstart=0

I can almost see a big grin appearing in Bob's avatar...
Hopefully his reply has given you a clue already?
If not, some explanation:
Many settings in the standard "Media" panel (for both video and audio) don't apply for publications that need to go the Folio-way. This panel is mainly concerned with lovely Flash stuff, but apart from the Poster frame and the Markers, it is useless for Folio's.
A quick guide: create a video with the necessary codec (H.264 for video, MP# or AAC for audio) at the required pixel size (exact width/height). Simply Place the file in InDesign, but don't scale it (or recreate and place a properly sized new video afterwards). Choose what to do with the Poster frame (and maybe some Markers), but all other settings are done in the Overlay Creator.
Check Bob Bringhurst's Tutorials and his DPS Tips app for more info. But I guess you get the idea now.

Transferring some files from old hard drive to new mac book pro: How do I do this? I bought a SATA Wire, and can't figure out how to get my files

Hi there, my old mac book recently died and I opted to buy a new macbook pro, instead of pouring lots of money into the old computer. I was able to get my hard drive out, and I bought a 2.5" Sata Nootbook Drive Upgrade Kit. I have also installed superduper!....but I can't really figure out how to get everything to work. I just want to be able to take some of my files from my hard drive, not everything...
Any suggestions?
Thanks!

I don't know what a "2.5" Sata Nootbook Drive Upgrade Kit" is but if you have a internal drive you need to connect all you needed was a $20 IDE/SATA to USB adapter
You don't need Superduper, that's software designed to clone a entire Mac's boot drive to a external drive for bootable backup purposes using the same machine/make/model.
Since the new Mac is different than the old one you can't clone (well you could but it will break the machine) the old drive to the new one.
However you can use the adapter above and software Apple provides in the Utilities folder on the NEW MAC, called Migration Assistant to transfer your User to the new machine.
However this might not be the best course of action as it can transfer unwanted data and cause problems in the Library, old programs that won't run on 10.7, etc.
You can simply create the same named user on the machine (System Preferences > Accounts) log into it and then connect the external drive with the adapter and copy the contents of your users folders over and place into the same.
It's always good to have another Admin level user account on the machine in case the primary one has a User based issue and you need to log into the other and grab files. So if either manually or via using Migration Assistant you wind up with two user accounts on the machine, it's really not that big of a deal.

W520: How to get full speed and turbo on battery power

Here is how you get around the on battery max frequency limitation (of 1.2 GHz, at least for my i7-2620M) and no turbo (well, almost, read on):
0. Assuming you have max performance enabled everywhere possible (BIOS/PowerManager/Windows Power Scheme)
1. Load ThrottleStop.
2. Set the multiplier manually to your maximum multiplier (e.g., 27x for i7-2620M, 23x for i7-2820QM, etc...) or Turbo (which is the setting after your max multiplier).
3a. Enable ThrottleStop
3b. (optional) Check in CPU-Z and make sure that your highest multiplier is being used when the CPU is utilized. If you selected Turbo, you should have turbo enabled at this point.
4. Disable ThrottleStop
5. Exit ThrottleStop, so that it doesn't waste any battery power, since it is no longer needed
This will change the max frequency (and max multiplier) available from whatever Lenovo decided to arbitrarily fix it at (e.g., 1.2GHz) to the correct max frequency (which in my case is 2.7 GHz / 3.2 GHz for turbo). Now your laptop will be able to correctly go from 800MHz to whatever is the max frequency of your CPU, using both EIST and C1E. Turbo will also kick in, if you enabled it in ThrottleStop and the Lenovo PowerManager app will even show it as enabled.
Thanks Unclewebb for letting us get around this stupid max CPU frequency limitation that Lenovo has imposed on us.
Disclaimer:
Do this at your own risk, since Lenovo does not officially support it.
Turn on active cooling, if you do CPU intensive stuff for any prolonged period of time. This will take away some on battery time, but if battery time is of ultimate concern to you, then this change is probably not for you to begin with.
If you go through prolonged periods of CPU intensive activity, you will lower your battery life and produce a lot of battery heat, because you will have a relatively high discharge rate. A high discharge rate reduces both the number of charge cycles and the maximum charge capacity of a Li-Ion battery. I don't know how safe all of this is, so do this at your own risk and probably monitor temperatures along the way. Other laptops can do Turbo and full speed on battery power (e.g., the slim 3 lb Sony Z, with the i7-2620M), but then other laptops have different designs and cooling systems, so who knows how the Lenovo W520 hardware will react to this.

Hi,
I have the opposite problem - my i7-2720QM is fixed at 2.2GHz no matter how hard I spank 1, 2 or all cores, and no matter what System Performance settings I apply. It even runs at this speed, and gives the same bench marks when on battery with the "system performance" set to Low.
No one even knows what the various System Performance settings actuall mean. E.g. Neither Lenvo support nor these forums could tell me what the difference between "Maximum Turbo","Turbo" or even "Low" under "System Performance" in the Lenovo power manager Advanced settings.
I have been trying go get turbo boost to work for 2 months. I have wasted so much time with this machine, I could have bought 2 Macbook pros for the cost of the time lost.
I dont know why Lenovo have disabled the turbo boost (and the opposite, turbo drop?) feature for this CPU - is it deliberate, or incompetence? Its certainly false marketing and extremely annoying that I have to use my ancient PC to do single threaded type work which I know the Laptop can manage if it were not crippled.
So people whos clock speed drops when on battery are the lucky ones. Mone doesnt even if I want it to.

HT1414 My iPod touch got stuck on fast forward on the sound and I can't get it back to normal. How do I restore normal speed sound?

My iPod touch got stuck on fast forward on the sound and I can't get it back to normal. How do I restore normal speed sound?

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

How can I get rid of speed download without the uninstaller?

Having trouble downloading, and reading that speed download could be the problem, I trashed it. The trouble is, I trashed the uninstaller along with everything else. Is there anyway to get rid of speed download? Safari quits when I try to download something, like a widget.
iMac G5 Mac OS X (10.4.8)

You're welcome. Glad to have helped.
Mahalo for the and Aloha from Big Island.

How to get 6bg Sata speeds on Big Bang MSI

Similar Messages

Maybe you are looking for