How to manage projects in TFS for better results in reports ?
Hello,
I have 5 team projects in TFS which is being managed by 5 team members.All the projects have been developed and currently there are up coming small level development task for enhancements or change requests.
I require to know best rules/practices points to manage the projects in such scenario so that I can get better results in reports.
Notes: There are no predefined sprints as we do not have information about upcoming module/task estimations.
Would you please help me to understand the rules/best practicies to follow in order to succefully manage the projects in TFS for betterment of the project growth ?
your help will be much appreciated.
Thanks and Regards,
Dipti Chhatrapati
Hi Dipti,
Thanks for your reply.
If you want create burn down report(or other reports) in team projects, you should configure the Reporting Service for your TFS Server first, then we can create team project using the
TFS default process templates, the default burn down report and other default reports will be generated after team project created successfully:
https://msdn.microsoft.com/en-us/library/dd380714.aspx.
Whether the team project created using which default TFS process templates, we can create work item query in team project filter work items:
https://msdn.microsoft.com/en-us/library/dd286705.aspx.
You can create these 5 team projects using the same process template, and create them in the same one TFS collection.
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.
Similar Messages
-
How to manage the Credit Control for Customer Consignment Process?
Hi All,
Could anyone tell me how to manage the Credit Control for Customer Consignment Process?
ThanksHi, there is not standard solution, we did customized process for consignment credit block , check below
1. defined status profile - with lock/auto/approved/rejected and new t.code for approval or rejected.
2. maintained consignment credit limit in Z table
3. logic for detemining status written in sales order save userexit.
4. while calcualting the values, system need to check open sonsignment order of customer/ open deliveries/ stocks at customer place MSKU table. and calculate value with MBEW/KONV ect.
5. if value is less than Z table then status AUTO, which do not need release, if value is greater than Z table put status LOCK means credit block need to release from new T.code.
Hope you get some idea -
How do I set individual properties for a column in report layout at runtime
How do I set individual properties for a column in report layout at runtime? I need to change this based on a user's input. This is for v10g.
I need to change either the "Read from File" attribute or the "File Format" attribute for one column based on the user's input. IS this possible?
Thanks in advance!Hi,
define 2 columns and use format triggers to show the one or the other column.
Regards
Rainer -
How to restore Project from repository for specific date ?
Hello,
I have Web Dyn Pro Project. Some files were deleted in project and were checked in to repository.
Could you please describe easy steps how to restore project state for specific date ?The only way you could do that was if you used Time Machine on the computer to make backups. You could simply store the mobile backups folder on the day you wanted and then restore the iPhone.
I've done this successfully in the past. -
How to manage IP address assignment for laptops?
Dear All,
I'm looking for an efficient way to manage IP address assignment for laptops.
I have a DHCP server with reservation for all my devices.
Laptops usually have 2 NICs: LAN and WiFi card.
So, how can I manage the IP assignment for these devices?
If I make a DHCP reservetion with two different IP addresses, I can have problems with DNS round-robin.
Should I enable the DNS secure dynamic update for domain members and then reserve two different IP addresses on DHCP?
I don't want that user needs to manually change their NIC configuration.
What you suggest?
ThanksThe best way to manage it would be to "not" manage it. DHCP by definition is supposed to be "dynamic". DHCP Reservations are great for a few devices that live under "special circumstances" but you never want to set Reservations for everything,...if
you do that then just don't have DHCP to start with and statically assign everything.
The combination of DHCP with dynamically updated DNS in AD means you never have to know or ever care what the IP# is. Everything is referred to by it's hostname.
Some things to keep in mind:
Every interfaces has a different MAC,...meaning the Laptops have two MACs. Therefore it is impossible to reserve the same IP# for both. So they end up with a different IP# depending on which Nic they use. Running two laptop nics on the same LAN at
the same time is always bad. Either always use the wireless,...or always turn off the wireless nic when laptops are local within your facility and can use the physical nic. In other words pick one,...or the other,...never allow both to work
at the same time. This is a responsibility and education issue of the user,...you can't do this for them.
User can not change their own network IP Specs unless they are Local Administrators on their machines,...and they should never be allowed to be Local Administrators. -
How to manage the font size for webRfc Reports
Hi All,
How to manage(increasing or decreasing) the font size for webRFC Reports.
Regards
SriHi,
Can you try republishing and see ....
Ideally the font size would be controlled by the <font tag and if you have made changes correctly it should be reflected correctly.
Check whether the HTML code is also correct.
Thanks & Regards,
Vijith -
OTL TIme card: How to make Project as criteria for Expenditure type
Hi,
I need to add project as criteria for Expenditure Type LOV.
Can we pass project information as bind varaiable to Expenditure LOV? I need to customize expenditure LOV such that it picks up expenditures defind at the project level apart from preference level.
THanks
PRasadHi,
You can do it by OAF personalization.
Enable the link 'Personalize page' on the given OTL page and then for that column set the rendered property as 'True' and then the column will become mandatory,
Regards,
Anshum -
How install Oracle Developer Suite 10g for Linux (Including Forms & Reports
hi
i want to install Forms & Reports Developer Suite in Linux OS So i have downloaded From OTN Site
"Oracle Developer Suite 10g for Linux (Including Forms & Reports)"
These are the File's i have Downloaded:
as_linux_x86_ids_101202_disk1.cpio
as_linux_x86_ids_101202_disk2.cpio
so in the Oracle Documentation Site they have given Guide as Follows:
$cpio -idmv < as_linux_x86_ids_101202_disk1.cpio
$cpio -idmv < as_linux_x86_ids_101202_disk2.cpio
after that what should i do ...
How to Install Oracle Developer Suite 10g for Linux (Including Forms & Reports)
Kindly Reply ASAPPl follow the steps in the Install Guide - http://download.oracle.com/docs/cd/B19375_02/doc/frs/install/B19314_02/toc.htm
Srini -
I am working with several others and we share some number of directories and at the same time own different directories for each projects. Problem rises when there are duplicated VI names are created by two users working on two different projects. Search path has to be manually changed to avoid loading a wrong VI. Sometimes user forgets to change and load a duplicated VI name. Is there a better way to manage th search paths?
LegalEngineer -
Matt's comments above regarding the SearchDirectories object only apply to TestStand 3.0.
Under TestStand 2.0.1, you have to manage the settings in the config file Testexec.ini. You can also have read access to the search directories by accessing the .Data.SearchDirectories array property that is returned from Engine.ConfigFile().
Scott Richardson (NI)
Scott Richardson
National Instruments
Attachments:
temp.jpg 15 KB -
How to manage different supply parameters for the same item based on demand quantity?
We are using unconstrained ASCP. We have some products that can be produced in a 'small' machine or can be produced in a large tank. If ASCP has created a planned order for a quantity less than 1000 it will be made on the small machine with the supply quantity = demand quantity. For example, we have a demand of 250, we will make exactly 250 on the small machine. But if the demand quantity is greater than 1000 we will make the supply in the tank with a fixed order quantity of 1590. Financially it will cost us less to do this and scrap the difference because the small machine is very expensive to run compared to the tank.
The challenge is, say we need 1200. ASCP generates a planned order for 1200 and all the dependent demands support 1200. Now we want to make 1590 and we are short of materials. This assumes we have set the item with no supply parameters. On the other hand, if we set a fixed order quantity of 1590 but only need 100 then we we have to scrap the materials for the balance due to a short shelf life.
Any ideas how to set a supply quantity using different parameters based on the demand quantity?
Mark MadalHi Mark,
I personally don’t see any standard solution for this requirement especially with an unconstrained plan.
However, if it is feasible, you can try below solution with a 'constrained plan with decision rules enabled' and check if it works,
1. 1. Define two different items – Item A and Item B
2. 2. Item A uses small machine in its routing and can have any demand that is below 999. So, Max order quantity = 999.
3. 3. Item B uses Large Tank in its routing and is a substitute of item A. Also, fixed order quantity = 1590.
4. 4. Define component substitution relationship between A and B. A and B will have identical BOM.
In a constrained plan with decision rules enabled, optimization logic will ensure that planned orders are generated for Item A whenever there is demand below 999. And for Item A, supply will always be equal to demand quantity. When the demand is more than 999, optimization engine will select substitute item B and will generated fixed supply of 1590 for it.
Check if this satisfies your requirement.
Regards,
Durgesh P
(Please mark this post helpful or correct, if answered) -
How can we rewrite this query for better performance
Hi All,
The below query is taking more time to run. Any ideas how to improve the performance by rewriting the query using NOT EXITS or any other way...
Help Appreciated.
/* Formatted on 2012/04/25 18:00 (Formatter Plus v4.8.8) */
SELECT vendor_id
FROM po_vendors
WHERE end_date_active IS NULL
AND enabled_flag = 'Y'
and vendor_id NOT IN ( /* Formatted on 2012/04/25 18:25 (Formatter Plus v4.8.8) */
SELECT vendor_id
FROM po_headers_all
WHERE TO_DATE (creation_date) BETWEEN TO_DATE (SYSDATE - 365)
AND TO_DATE (SYSDATE))
ThanksTry this one :
This will help you for partial fetching of data
SELECT /*+ first_rows(50) no_cpu_costing */
vendor_id
FROM po_vendors
WHERE end_date_active IS NULL
AND enabled_flag = 'Y'
AND vendor_id NOT IN (
SELECT vendor_id
FROM po_headers_all
WHERE TO_DATE (creation_date) BETWEEN TO_DATE (SYSDATE - 365)
AND TO_DATE (SYSDATE))
overall your query is also fine, because, the in this query the subquery always contain less data compare to main query. -
HT4865 how to manage space on icloud for non us resident ?
how to add more space on icloud for non us resident or non visa or mastercard availible ?
Hello ALI2106,
Thanks for using Apple Support Communities.
In the support article linked to below you can see the price required for your country in order to upgrade your iCloud storage.
iCloud storage upgrade pricing
Take care,
Alex H. -
How to manage 3 cinema displays for 2014 mac mini
Is it possible using the the two thunderbolt ports to: attach 2 monitors using daisy chain for one thunderbolt port, and the third monitor using the second thunderbolt port?
would like not to use the hdmi port as i would like all three resolutions to be high
thanks in advanceIt may not support three monitors. Apple says for the late 2014 Mini:
Video Support
Support for up to two displays at 2560 by 1600 pixels, both at millions of colors
Thunderbolt digital video output
Native Mini DisplayPort output
DVI output using Mini DisplayPort to DVI Adapter (sold separately)
VGA output using Mini DisplayPort to VGA Adapter (sold separately)
Dual-link DVI output using Mini DisplayPort to Dual-Link DVI Adapter (sold separately)
HDMI video output
Support for 1080p resolution at up to 60Hz
Support for 3840-by-2160 resolution at 30Hz
Support for 4096-by-2160 resolution at 24Hz
DVI output using HDMI to DVI Adapter (sold separately) -
How to manage Database connections in ADF better
Hi,
We have got our DB connection configured as a JNDI service in weblogic server and in used in many functionalities where we rely upon EO / VO concept totally.
Now we have requirement from customer that every connection borrowed from the pool must call a DB procedure first as below before executing the app related SQL or anything:
DBMS_SESSION.setIndentifier('<app_user_id>');
When firing custom SQL, I guess it is fairly simple to do this but when it comes to EO/VO where ADF takes care of DB calls, We do not know how to achieve it effectively ...
Can anyone help how to achieve this ?
-Thanks a lot
- RamCode like this belongs in the AM - you can override the prepareSession() method of your AM implementation class to do this. Have a look at [url http://download.oracle.com/docs/cd/E21764_01/web.1111/b31974/bcservices.htm#sthref929]the docs
John -
How to manage accents in filenames for ZIP compression?
Hi!
Using java.util.zip package to zip files, I have problems when there are accentued letters (such as �, �, �, �, �, �, etc...) in compressed file names. When I open the resulting ZIP file under WinZIP (I use Windows 2000), I see strange caracters instead of accentued ones. It must be something like an ANSI/ASCII conversion problem, but I couldn't find a way to solve this.
Any idea?
Thanks!
Reihtul.. I tried to convert file names using things like:
return new String(accentuedString.getBytes(),"Cp437");
or:
StringOutputStream sos=new StringOutputStream();
try {
PrintWriter sout = new PrintWriter(new OutputStreamWriter(sos, "Cp437"));
sout.print(accentuedString);
sout.flush();
sout.close();
return sos.toString();
} catch (Exception e) {
return accentuedString;
... with different format names (Cp436, ISO8859_1, etc...)
But nothing worked. I also searched the web for a solution but I couldn't find any. It seems there is no reply to this question!
Any idea?
Thanks!
Reithul
Maybe you are looking for
-
My hard drive removed from a laptop no photograph files left can I recover them?
Please HELP with advice someone if you can. I had a white unibody laptop which was snow leopard but upgraded to Lion. A couple months ago my daughter splashed a small amount of water on it whilst it was unplugged when I was working on it. No apparent
-
Why i can't open my iphoto app?
Process: iPhoto [954] Path: /Applications/iPhoto.app/Contents/MacOS/iPhoto Identifier: com.apple.iPhoto Version: ??? (???) Build Info: iPhotoProject-628000000000000~3 Code Type: X86 (Native) Parent Process:
-
Rank in QaaWS not working correctly?
Hi, I am trying to integrate a simple Top 10 customers query in XCelsius using QaaWS: I've built a simple universe on MS AdventureWorksDW Sample Database. Using this universe, I've built a QaaWS using dimension Name, measure Sales amount (sorting on
-
Newbie : JSP session problem after reload with IE refresh button.
Hi, I had an issue with JSP reloading using tomcat 4.* and IE. I have a jsp1.jsp is opened in two different IE windows(one by one). Once i refreshed using IE refresh button from the first window, its loaded with second windows session details. Its ch
-
All of the other tabs work fine. Only Yahoo has disappeared after several years of sending me directly to my email account. Help is appreciated.