HP LaserJet 4200 -- manual feed tray not working after 10.6 install

Hi all...
One of my users pointed this out to me. I'm looking for confirmation (or a solution)?
We have an HP LaserJet 4200 printer added to our mac clients as an IP printer. Under 10.5.8, printing to "Tray 1 (Manual)" goes where you think it would -- to the manual feed tray.
Upgrading to 10.6.1? Manual print jobs are going to the internal "Tray 3".
It's the same behavior if I use the 10.6.1 "5.3.0" printer driver or the HP Printer Update 2.1 updated "5.4.0" version.
Can anybody else confirm/deny the problem with their 4200 printer under 10.6? If you can confirm it, do you know of a fix (short of rolling back to 10.5.8).
A remove and readd of the printer did not help here. Unfortunately.
Thanks!
- Steve

Resolved this two ways:
1) the "gutenprint" driver worked.
2) The larger problem was the manual tray had been set to "A4" size.
I used the web admin interface to set this to "any size" and "any" type and that fixed the problem with the 5.4.0 "LaserJet 4200 Series" default printer driver...
Luckily, somebody else on campus had one of these printers and we were able to compare the printer setting differences to figure this out.
I hope this helps somebody!
- Steve

Similar Messages

HP Photosmart C6300 printer/scanner not working after Snow Leopard install

HP Photosmart C6300 printer/scanner not working after Snow Leopard install
Reinstalling etc does not work - does anyone else have the same problem or a clue as to how to fix this?

Keith,
I got a C6280 and the scanner does not work anymore. I am for 6 days in contact with HP. The last printer driver install form the apple web site does not open the image of HewlettPackardPrinterDrivers.dmg because of an invalid checksum. The skipping of the validation gives and error in the install.

HT3917 My apple wireless keyboard is not working after new batteries installed

My apple wireless keyboard is not working after new batteries installed.

Do you get a steady green light to say there is a connection. If not, are the batteries the right way round. Do you have a monitor to tell the batteries strength. Is there a reading. Are the batteries good quality ones, Duracell, Energiser or Apple rechargeables.

Touchsmart 320-1030 Touchscreen is not working after OS re-install

HDD crashed, and was replaced with new, re-installed system from factory recovery CDs, now touch screen does not work. I have re-installed the drivers to no avail. system Properties says under Pen and Touch: No Pen or Touch Input is available for this Display. It used to work before the hard drive crashed. Is there a setting in the BIOS? or something else I may have missed?
Thanks

Hello @ncmich2,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how the Touchscreen of your desktop computer is not working after replacing the Hard Drive, and I would be happy to assist you in this matter!
To re-enable the touchscreen features on your computer, I recommend re-installing the original software and hardware drivers that first came with your computer. This can be done by following the steps in this document on Using Recovery Manager to Restore Software and Drivers (Windows 7). To update the newly installed software, please follow this resource on Using HP Support Assistant (Windows 7).
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Keyboard and Touch-Pad Not Working After Having to Install New Hard Drive

I had to install a new hard drive in my HP Pavillion DV9700t that has Vista Home Premium 64-bit. After going through the recovery process with backup disk the built in keyboard and touch-pad do not work. During the installation, an error message came up saying something along the lines of "the drivers are not supported by this verison of windows because they are unsigned." The drivers that had that error were "hpqkbfiltr keyboard filter driver," "HP remote control HID Device," and "hpqkdfilter driver." I tried to update the drivers for the keyboard from the hp website, but the keyboard and touch-pad still do not work.
My question is, where do I find the digitally signed drivers for the keyboard and touch-pad that Vista won't flag and disable?
Help please!

Sparkles,
Thanks for the suggestions.
When dealing with MS Fix It, I was choosing run. Upon further investigation on that site, there really isn't a scan that applies to my issue anyways I tried the .NET Framework repair tool, and that seemed to work. It told me to try re-running what I was having issues with, so I tried running the Windows PowerShell again, but again was faced with the following message "windows update standalone installer encountered an error: 0xc8000247." I went back to the .NET screen and hit "Next" because it didn't work, and that responded by saying they were going to submit logs to Microsoft. I won't hold my breath on that one.
I'm to the point where I honestly don't care anymore. I have no idea what to do, because doing a clean install with the discs HP sent me isn't going to help because they are just recovery discs, and not an actual Windows disk. This is the second hard drive I have had to put into my laptop and use those recovery disks on in the last 3-years. The built-in keyboard hasn't worked during that time frame on either hard drive. I don't think the recovery disks I was sent install properly. Not sure where to go from here. I spent way too much money on this laptop years ago having it custom built to handle all of my drafting programs, so I don't want to just kick it to the curb. I was looking into the possibility of just replacing it, but I cannot stand the Windows 8 interface.
I guess I should have fixed the issue with the keyboard on this hard drive before loading all of my programs. Between the recovery disk install, formatting of the hard drive, and installing all of my programs it took well over 12 hours. Not really looking forward ot that again Then there's shockwave and flash and all of the other goodies that my recovery disks won't restore anyways.
Sorry if this seems like a negative post, but I'm just tired of trying to no avail. Maybe I should just take it somewhere to get it looked at, but I can't see them being successful if the recovery disks won't help anyways.
Thanks for you help,
MadBuch

Siri does not work after IOS 7 install

Siri doesent work after I OS 7 install I hear it is a hardware problem. Siri works fine but then you download IOS seven and it stops working. Apple has told a couple people they have to buy a new phone. I hope thats not true. Because I will buy a new phone but it wont be apple if thats the case.

Hello, Dan.
Thank you for visiting Apple Support Communities.
I would recommend going through the troubleshooting steps in the article below when experiencing issues with Siri.
iOS: Troubleshooting Siri
http://support.apple.com/kb/TS4079
Cheers,
Jason H.

Secondary monitor does not work after OS X install

My secondary monitor does not work well after OS X install. The image on my secondary monitor is different even the screen svaer image is different and the mouse can not be seen.

Try the easy thing first - NVRAM reset:
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
If that does not work, post back with more info, including the version of Mac OS you are running. How is the external monitor connected, did it ever work, and from what OS X to what was the "OS X install" in your title?

Iphoto not working after time machine install

I have a first gen intel iMac and the hard drive had a sudden failure I was not overly concerned about my Data as I use time machine. I had a new Hard Drive installed and I used time machine to install back to snow leopard. all seems fine for a few days and every thing (software and hard ware (scanner)) was working fine. then I opened iPhoto to add a few new photos and all I get is the spining beach ball the library is 26 gig in size and was working fine before. I am at a loss as I still have all 9745 original photos on back up drive but not in order like in iPhoto and really don't want to recreate my library all over again. I've done disk permissions and only seem to have a problem with Java any body got any ideas?

Hi there Guys
I don't know if this is a true fix but my iPhoto 11 is now working iPhoto had an update and I did it to both my iPhoto programs (mac book and iMac) I then opened the not working librery on the laptop and it said the library need to be updated it did this and opened okay and all was working fine (I copied library on to a portable FireWire HD) when I copied it back to my iMac it said the same and went through the update and is now working fine.

Safari will not work after Snow Leopard Install

Safari does not work. It opens briefly, then closes. I get a message to "click reopen to open application again," but the same thing happens. Please advise.

Janice,
Quit Safari if it's open.
Locate this file. com.apple.safari.plist
/Users/YourName/Library/Preferences. Drag that file from the Preferences folder to the Desktop.
Launch Safari. If it launches without crashing, then that .plist file is corrupted. Drag it to the Trash, empty the Trash and restart your Mac.
If Safari still crashes...
Go to ~/Library/Caches/Safari and delete all the sub-folders within that one.
Go to /Users/YourName/Library/Safari and delete Home/Library/Safari and delete any of these files you have there:
Downloads.plist
History.plist
LastSession.plist
Carolyn
Message was edited by: Carolyn Samit

TS3479 quick time not working after snow leopard install?

Made video's on my iphone and loaded them to my imac. Video did not work in iphoto. No Quick time pop up. what happened? Snow leopard install.

You need to re-install iPhoto because it's missing bits of itself:
Library not loaded...
Reason: no suitable image found.
Looking at the missing files it's possible that it's missing from the OS. But start with re-installing iPhoto, and if that fails you'll ned to re-install the OS.
To re-install iPhoto
1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
2. Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name
3. Re-install.
If you purchased an iLife Disk, then iPhoto is on it.
If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only...’
Regards
TD

Thunderbolt is not working after Mountain Lion installed

I'm putting this discussion again because the problem didn't solve like I thought !
As you can see from the title that I have a problem already after I installed the new OS X Mountain Lion. I got my thunderbolt to Hdmi adabtor connected to an LCD TV and it was working great with snow lepord. But after the I installed Mountain Lion. it won't even recognize that there is something connected and I don't see the options in my System Prefrences> Diplays like before.
I already run software update and it's all up to date and also done a PRAM reset and nothing changed.
It only ok for a couple of min. if I restarted it and without the sound working from the LCD TV.
Please I need help here.

Well I would have hit repair. This might be stemming from a deeper issue with the installation. I've never seen that dialogue box before, and if ignoring it and booting normally worked for you then I say you did the right thing.
however
I would, go to disk utility and then select your boot drive and verify and repair disks and permissions.
if anything else WEIRD should occur, you may want to go to the recovery partition of ML (cmd+R while hearing the boot chime) and reinstalling ML. That dialogue box you mentioned is strange and should be noted. A reinstall will probably fix whatever issue comes up.

Printing 4x6 photos on HP Laserjet 4630. photo paper tray not working?

I am trying to print 4x6 photos on glossy paper. My printer has a photo paper tray in addition to a standard letter tray. When I specify 4x6 borderless glossy paper in the print parameters, the printer keeps pulling from the standard paper tray instead of the photo tray on top of the printer. This has worked for me in the past, but I haven't used it in a long time. What must I be doing wrong?

Hey. I'm a photographer with the C4280.
This printer takes care of 8.5 x 11's pretty much perfectly. But 4 x 6 not for me on iPhoto or Photoshop.
So what I did was I set up a pages document with a blank template, set at 4 x 6 inches.
I dragged rulers about .25inches in and threw in the photo set at 4 x 6 ratio. So... most photos are 4 x 6, just resize it to fit in the rulers.
I've noticed in most occasions it cuts off the top of the photo document when laid out in portrait.
What I do is a hit command p, select the printer but choose under the drop box that says "layout" i hit borderless printing, and a selectable box will show up saying "print borderless" and i just clicked it.
on the document though you might want to make the opacity 10% to save ink. you have to trouble shoot the exact place to set and drag up or down the photo. but once you get it, its reliable the duration the document is open and the printer is on.
i know its kind of pointless for one, but i had a shoot with live printing on the spot with this printer and its great. you can add texts boxes and put those perfectly where you want (once you set the picture so its set) and throw in another picture and really customize the 4 x 6.
i printed a postcard with the writing already in it. just had to mail it no writing involved.
you also need iwork 08 or 09. i have 08 but im sure 09 works. so if you save the pages doc as a template you can just drag in the image file into where the old image is and print that way.
command p, choose borderless printing in the drop box and click print borderless. it should work.
email me for a copy of my pages document. [email protected]
i promise though, with canon or epson 4 x 6 print paper, its pretty amazing. almost comparable to my prints from my printer.
or you can fit 12 3.5 x 2inch (business card sized) pics on an 8.5 x 11.

Console not working after CF 10 install

I have installed CF 10 and the console in CF Builder 2 no longer seems to work? Both products are fully up to date and I have the same issue on 3 separate dev machines. All else, works fine. Did somethin change with CF 10? A complete frsh re-install of CF Builder does not help either... I am on Win7 Pro, 64b and 32b... same issue.
Upon starting CF Builder, the localhost Server console will say this:
[localhost]:(12/10 at 01:53:40) Server is available. Getting server settings.
but that's it. Nothing after that. Stopping and restarting CF from within Builder does not fix this?
Also, I read on a blog re: CF 10 "beta" that you no longer need to set the CF service to manual in order to get the full effect of the console, etc. in CF Builder. Is this the case and the proper way to handle this now?
Andy

Andy, here’s a thought: you don’t make it clear in your original post, but have you edited the “server” definition (for that being shown in the console message you’re observing) to change it to indicate that the server is CF10?
When you right-click a server (in the Servers view), and choose “edit server”, the “application server” drop-down has a new value (only in CFBuilder 2.0.1, mind you) to point to “CF+Tomcat Bundle”. You’ll want to make sure the server, port and username/passwords are all correct for the new CF10 instance as well. Similarly, click the “next” button to configure the server home and docroot.
Sometimes people are stumped by this server configuration (either they miss it, or don’t feel there’s enough info on the screens). For more, see either the docs:
http://help.adobe.com/en_US/ColdFusionBuilder/2.0/Using/WS0ef8c004658c1089-38317734121cdfd 5fd3-8000.html
Or these older blog entries, which while focused on remote config, may still interest some regarding server setup:
http://blogs.adobe.com/cfbuilder/2009/07/remote_server_setup_is_it_real.html
http://blogs.adobe.com/cfbuilder/2009/07/remote_server_setup_-_multiser.html
Let us know if these help.
/charlie

Satelite Pro L20 - LAN Not working after OS re-install

I have just recently replaced my hard drive and I used the product recovery disk etc.
WXP loaded perfectly and now my wired LAN does not seem to want to work. All it is giving me a limited or no connectivity.
I have tried to uninstall and re-install the drivers, manually enter the IP settings and still nothing will work.
I wondered if anyone else has had this issue before and could offer me any advice.
Many thanks in advance
M8KWR

Maybe you should check your settings at your router. Maybe some wrong DNS,Subnetmask, etc.
Did you already checked the cable?? Perhaps the cable is malfunctioning. Just cross-check it with another cable.
Would appreciate to get some feedback from you.
By the way, which operating system do you use?
Greetings

Microsoft apps (outlook/Excel etc) do not work after SAPGUI 720 install

Hello,
We use a tool called MARIMBA to package and deploy SAPGUI and other apps to our users. Recently, we packaged SAPGUI 720 and deployed to some end-users (Win XP 32-bit SP3, Win 7 enterprise) via Marimba. However, after SAPGUI gets pushed to the end-user computers, users complain that their Microsoft apps don't work or are missing! Few users report Symantec Anti-virus does not launch.
I am not sure if this is unique to our environment. Please report here if you have encountered similar situation.
Thanks for your time.
Edited by: Gokul Ramaswamy on Apr 9, 2011 12:48 AM

You software is too old. You need to move to Office 2008, 2011 or use iWork or use Open Office (or Libre Office, or NeoOffice, etc.)

HP LaserJet 4200 -- manual feed tray not working after 10.6 install

Similar Messages

Maybe you are looking for