HREAP on LAP reboot

Hi,
I've got HREAP working well, in that when an AP loses conenctivity with the WLC the AP continues to push out a LAN over radio and clients are authenticated back onto a radius server that the AP can see when disconnected.
I have one burning question: When an AP in HREAP power-cycles (and still cannot see the WLC), does it lose its HREAP config? I'll be really, really annoyed if it does.
This is what I'm seeing at the moment. A newly rebooted LAP just seems to spend its time saying
*Mar 1 00:22:39.872: capwapHandleDiscoveryTimer Expired
and not doing anything remotely HREAP.
Anyone had any issues with this?
Thanks,

I still think this should work even though Cisco UK have said that it will not. My LAP that has been restarted has a few files in flash. they are as follows:
2 -rwx 40572 Jul 29 2009 15:25:17 +00:00 lwapp_reap.cfg
3 -rwx 0 Mar 1 2002 00:16:57 +00:00 validate.txt
154 drwx 128 Mar 16 2009 11:17:19 +00:00 c1130-rcvk9w8-mx
4 -rwx 296 Jul 29 2009 15:25:13 +00:00 env_vars
5 -rwx 29298 Jul 29 2009 13:42:29 +00:00 event.log
6 -rwx 5 Mar 16 2009 11:17:45 +00:00 private-config
9 drwx 256 Jul 29 2009 12:10:47 +00:00 c1130-k9w8-mx.124-18a.JA1
7 -rwx 7192 Mar 1 2002 00:00:31 +00:00 private-multiple-fs
The top one is a reap.cfg file, which when I do a 'more' command contain some basic information about the WLAN that is supposed to be being pushed out by the radio, but for some reason the LAP is ignoring this and spending time trying to get to a WLC that it can never reach - as i've created a fake WAN failure between the LAP and WLC.
Any ideas?

Similar Messages

HREAP mode AP assigns random 5GHz (802.11a) channel after reboot

The channel and power levels for the 2.4GHz and 5GHz radios have been manually configured on an HREAP mode AP. The 5GHz channel is 149 (non-DFS) with a power level of 2 (14dB). When the HREAP mode AP reboots the 5GHz channel initially displayed is the same manually configured 5GHz channel. If the AP is unable to connect to the WLC and enters HREAP standalone mode, the 5GHz radio channel is then randomly assigned a channel from the UNII-1, UNII-2 or UNII-3 bands. The WLC is on v7.0.116.0. I have seen the same results using 1142, 1262, 3502i and 3502e APs. See example CLI output from AP below.
AP01#show capwap reap status
AP Mode: REAP, Connected
Radar detected on:
AP01#show controllers d1
interface Dot11Radio1
Radio Dortmunder 5, Base Address 68bd.abfd.45a0, BBlock version 0.00, Software version 3.00.81
Serial number: FOC1436A5AW
Spectrum FW version: 1.13.44
Number of supported simultaneous BSSID on Dot11Radio1: 16
Carrier Set: Americas (OFDM) (US) (-A)
Uniform Spreading Required: Yes
Configured Frequency: 5745 MHz Channel 149
Allowed Frequencies: 5180(36) 5200(40) 5220(44) 5240(48) *5260(52) *5280(56) *5300(60) *5320(64) *5500(100) *5520(104) *5540(108) *5560(112) *5580(116) *5660(132) *5680(136) *5700(140) 5745(149) 5765(153) 5785(157) 5805(161) 5825(165)
* = May only be selected by Dynamic Frequency Selection (DFS)
AP01#show capwap reap status
AP Mode: REAP, Standalone
Radar detected on:
AP01#show controllers d1
interface Dot11Radio1
Radio Dortmunder 5, Base Address 68bd.abfd.45a0, BBlock version 0.00, Software version 3.00.81
Serial number: FOC1436A5AW
Spectrum FW version: 1.13.44
Number of supported simultaneous BSSID on Dot11Radio1: 16
Carrier Set: Americas (OFDM) (US) (-A)
Uniform Spreading Required: Yes
Configured Frequency: 5825 MHz Channel 165
Allowed Frequencies: 5180(36) 5200(40) 5220(44) 5240(48) *5260(52) *5280(56) *5300(60) *5320(64) *5500(100) *5520(104) *5540(108) *5560(112) *5580(116) *5660(132) *5680(136) *5700(140) 5745(149) 5765(153) 5785(157) 5805(161) 5825(165)
* = May only be selected by Dynamic Frequency Selection (DFS)
Any thoughts as to why or how to prevent?
Thanks,
Bill Jenkins

Welcome to the forums.
One thing you can try is re-check, if you get better results with different wireless-n settings: http://wireless.kernel.org/en/users/Doc … figuration
The driver might need a+n mode for 5Mhz AP operation according to other posts.
Another thing to follow up: The openwrt 12.09 (out last week) implemented patches for _experimental_ ath5k/9k support for 5Mhz. I have no experience with it on ath9k myself, but if it is new to openwrt and they call the new feature experimental - the vanilla driver very probably is the key to your problem.

Cisco AIR-LAP 1131 reboot in loop

Hi Everyone
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00CD9790 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000C3
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00CDB580 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x0184C8AA R17 = 0x0184C71B R18 = 0x00CDB760 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00CD9790
Frame 00: SP = 0x00CD97D0    PC = 0x0048A6A8
Frame 01: SP = 0x00CDB728    PC = 0x004361FC
Frame 02: SP = 0x00CDB740    PC = 0x0042E078
Frame 03: SP = 0x00CDB758    PC = 0x0044880C
Frame 04: SP = 0x00CDB798    PC = 0x0042A280
Frame 05: SP = 0x00CDB7C0    PC = 0x0042AA68
Frame 06: SP = 0x00000000    PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute,
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
Thanks for any help and consideration .
Regards

Hi Scott
Thanks for replying
here is the full output between loops :
Press RETURN to get started!
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048 , LR = 0x48A8A0
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
CPU Register Context:
MSR = 0x00029230 CR = 0x53000035 CTR = 0x00000072 XER   = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3    = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7    = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11   = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15   = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19   = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23   = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27   = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31   = 0x00003D80
Writing crashinfo to flash:/crashinfo_20130301-155213
=== Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
Buffered messages:
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
*Mar 1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Queued messages:
*Mar 1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Nested exception_rom_monitor call (2 times)
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00D1EC18
Frame 00: SP = 0x00D1EC58    PC = 0x0048A6A8
Frame 01: SP = 0x00D20BB0    PC = 0x004361FC
Frame 02: SP = 0x00D20BC8    PC = 0x0042E078
Frame 03: SP = 0x00D20BE0    PC = 0x0044880C
Frame 04: SP = 0x00D20C20    PC = 0x0042A280
Frame 05: SP = 0x00D20C48    PC = 0x0042AA68
Frame 06: SP = 0x00000000    PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute, 7 seconds
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
flashfs[0]: 40 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 15129600
flashfs[0]: Bytes available: 869376
flashfs[0]: flashfs fsck took 41 seconds.
Base ethernet MAC Address: d8:67:d9:ba:9f:2e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
Image text-base: 0x00003000, data-base: 0x005AEE20
Initializing flashfs...
flashfs[1]: 40 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 15129600
flashfs[1]: Bytes available: 869376
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio 1 A506 7100 E8000000 A0000000 80000000 3
Radio 0 0 0 0 0 0 2
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
LWAPP image version 4.1.192.35
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D8:67:D9:BA:9F:2E
Part Number                          : 73-13304-02
PCA Assembly Number                  : 800-36409-01
PCA Revision Number                  : B0
PCB Serial Number                    : FOC16304BZJ
Top Assembly Part Number             : 800-29582-03
Top Assembly Serial Number           : FTX1632N00D
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131G-A-K9
Press RETURN to get started!
Also , the switchport is a trunk port, i can definitely try it an access port .

LAP 1142 Reboots

Have 1142 LAP AP's installed in each floor, All AP in One specific Floor are rebooting. After reboot most AP are joining WLC but few are unable to Join WLC. Logs in WLC shows AP has Crashed due to
"Unexpected exception to CPUvector 2000, PC = 0x49DFE8 , LR = 0x49DFFC : Unexpected exception to CPUvector 2000, PC = 0x49DFE8 , LR = 0x49DFFC"
and
"Last AP disconnect details
- Reason for last AP connection failure.................... Data transfer message received from an unsupported AP
Would like to i) debug further for reason of AP reload ii) Reason for AP not joining WLC after reload /crash.
Is there way to collect AP debugs from WLC ? Any suggestion to prevent reloads from happening.

This is bug CSCtx92385, No workaround yet
Saurav,
Whoever created updated the bug needs to review the accuracy of the content. Under the Details > Product it states AP is a 2700. Under Details > Known Affected Release it states "7.0(116.0)".

I Am Using Photoshop CS5 - I Used To Be Able To Open Multiple SINGLE Files - Now They Over Lap - What Do I Do ¿ - How Can I Reboot My App To My Original Settings ¿

I Am Using Photoshop CS5 - I Used To Be Able To Open Multiple Single Files - Now They Just Overlap As One File ! - How Can I Fix This Or Reboot My App To My Original Settings ?

In Preferences UNcheck Open Documents as Tabs

LAP 1131 Rebooting Every 5 Hrs

Hi All,
We have 5508 WLC with 7.4.100.60 Ios. and we have multiple Ap's in our network (3600,1131,1242) and integrated with 5508.
We found on eissue recently i.e. all 1131 access points are rebooting every 5 to 6 hrs.
Let me know waht is the issue and solution.
Regards,
Satish.

For 1142 & 1040 series there was a bug (CSCud97983) in 7.4.100.0 code, but it was fixed in 7.4.100.60. If you having specific issue to 1131 after WLC code upgrade, it could be a bug.
As Scott suggested open a TAC case & Cisco may give you an engineering release which could fix your issue (if you do not want to downgrade). We were using 7.4.100.60 & had few critical bugs.. so now we are running on 7.4.100.107 given by TAC.
You can find certain bugs impacted us with this 7.4.x code from here.
http://mrncciew.com/2013/02/10/day-0-with-wlc-7-4-code/
HTH
Rasika

Notepad- Lap-Top, Pavilion, Wiped [D:] Drive in error, lost emergency reboot files?

HI: Recently, I uninstalled all data on my data [D:] drive, in attempt to create more space, as I was save my backups there, wasn't a notice create more physical space, I do not know HOW.    Remain so a problem.
                   Then I compounded that, realizing I removed all HP original emergency files, so in thos 4 categories, I more or less have no files/folders, nor ID bytes.
                           That being in order.. $recycle bin; Scotty-PC, System Vol. Info., Medial ID.BIN,   Altho in #1..I have 1 File - 129 bytes.    The recent date of change was..25/11/2014....of my indeed dirty deed.
                           I now better realize HP original message/warning not to uninstall any of these 4 files, all required for emergency recovery, known in some order as:::: Recovery, $Recycle Bin, boot, p, PC-Dr., ?, pcdr, or Preload.
                           Without these files there is no system recovery, no I didn't make an original recovery boot, at least I don't recall, I can check my elsewhere filing plc. to confirm that.
                           Are there any reasonable suggestions to this matter.
                            I am   NOT   in any immediate state of emergency,   my HP Notepad is more or less working ok, a little slow, but I'm uninstalling programs, that I do not need.   I have a upgrade   Vista, to Win. 7, H. Premium, OEM, RAM at 2G's, some 5-6 yrs. vintage, never a prev. problem.   On a wireless set up, for stationary home pc usage, by one person.
                        From:   Kannu or Kannutipper, of Canada.    Thank You...   I wish to recover these files, maybe utilize   'Recuva', or new HP-D/l, can't seem to access that.   The D dr. is starting to d/l over the empty files space all lost, so be it.
                                                                 k   +      1/3/15

kannutipper
Welcome to the HP Community Forum.
From what I can gather:
You have accidentally removed your Recovery Drive Partition,
You are not in any immediate danger of losing the rest of your data,
You are continuing to remove chunks of data from some other part of your computer -- presumably the C drive at this point
You have never made any Recovery Disks
You have apparently not used a third party software to make a Disk Image of your data
You would like to have a Recovery Disk set
There are a number of dv9500 systems, none of which have Recovery Kits available from HP any longer.
What to do?
=======================================================================
Recovery Kits
You might depend on these folks to provide a Recovery Kit -- they specialise in Recovery Kits for vintage HP computers. The cost is only a bit higher than you might have paid for the Kit from HP had it been available.
I cannot check the specifics for you without the Product Number -- you can check for yourself to see if they have what you seek:
Recovery Kits for Vintage HP Computers
Computer Surgeons HP Recovery Center
The company provides an 800 number you can call with any questions.
=======================================================================
Disk Image Software
Barring a purchased Recovery Kit, or in ADDITION to it, you might try using some Third Party software to make a Disk Image of what you have now before you lose it. That way you can at least get back to where you are at the moment. That you have some extra bits of software on the computer does not matter as much as the fact that the computer does, in fact, RUN and operate.
There are a LOT of companies that specialise in this sort of software.
One such:
Redo software is NOT Windows dependent and can be used with Both Windows and Linux Operating Systems.
Redo Backup – Recovery – Bare Metal Restore
Edits 04-Jan-2015
I suggest that you provide for the following stop-gaps to protect your data and access to your computer:
Prior to making changes to your computer, for example remove programs or make other changes:
Create a Restore Point:   Create a Restore Point – Win7 OR Create a restore point Win8
As a matter of protecting your data&colon;   You might consider that having an extra copy (or two) of your most critical files is a good idea. Placing those files on a USB drive -- or two -- and then placing that Drive into a Safe location (locally and away from your primary residence) might be a very good idea. Why do this? Computers have a habit of failing when you least expect it -- and at the worst possible time.
HP PCs - Backing Up Your Files (Windows 7)
Do not be the one locked out of your computer because you lost your password. Do not be the one locked out of your computer because your account becomes unusable due to corruption. The following was written for Windows 8.1 -- the logic applies to Windows 7 and the methods are similar.
Create a User Account with Administrative Privileges – Windows 8-8.1
=======================================================================
Click the Kudos Thumbs-Up to show you appreciate the help.
I am pleased to provide assistance on behalf of HP. I do not work for HP.
Click Accept as Solution when the Answer provides a Fix or Workaround!
Kind Regards,
Dragon-Fur

WLC5508-LAP1131 HREAP connectivity Problems

Hi group,
I have a problem with Hreap Ap in remote sites.
Sometimes, WAN connectivity is loss, and when the WAN access going UP some LAP stay in standalone mode.
I must reboot all the ap in standalone mode to recover all my AP in connected mode.
I can't understand why some ap in the same remote site stay in standalone mode and others go back to connected mode.
I'have more than 50 sites and ~15 LAP per sites. I saw this probleme in all my remote sites.
I have four 5508 in 7.0.196.
When i saw this problem, i can open telnet or SSH connexion in the remote standalone AP and I can ping the WLC with ~60ms response time.
With Debug on remote standalone AP:
DTLS:
DTLS ERROR debugging is on
LWAPP:
LWAPP Client ERROR display debugging is on
UDP:
UDP packet debugging is on
CAPWAP:
CAPWAP Client config display debugging is on
CAPWAP Client ERROR display debugging is on
CAPWAP Client DETAIL display debugging is on
CAPWAP Client Packet display debugging is on
CAPWAP Client Reassembly display debugging is on
CAPWAP REAP debugging is on
CAPWAP console CLI allow/disallow debugging is on
I saw :
*Jul 18 09:51:56.149: UDP: sent src=X.X.X.156(41188), dst=255.255.255.255(5246), length=154
*Jul 18 09:51:57.146: UDP: rcvd src= X.X.X.158(67), dst=255.255.255.255(68), length=313
*Jul 18 09:51:57.147: UDP: rcvd src= X.X.X.158(67), dst=255.255.255.255(68), length=313
*Jul 18 09:51:57.172: UDP: rcvd src= X.X.X.158(67), dst=255.255.255.255(68), length=313
*Jul 18 09:51:57.192: UDP: rcvd src= X.X.X.158(67), dst=255.255.255.255(68), length=313
*Jul 18 09:52:00.194: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface FastEthernet0.1 obtained IP from DHCP...
*Jul 18 09:52:00.195: CAPWAP_DETAIL: Dtls Event = 38 Capwap State = 2.
*Jul 18 09:52:00.195: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Jul 18 09:52:00.277: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0.1 assigned DHCP address X.X.X.156, mask 255.255.255.224, hostname AP2
*Jul 18 09:52:00.278: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface FastEthernet0.1 obtained IP from DHCP...
*Jul 18 09:52:06.149: UDP: Random local port generated 54254, network 1
*Jul 18 09:52:06.149: Reserved port 54254 in Transport Port Agent for UDP IP type 1
*Jul 18 09:52:06.149: UDP: sent src= X.X.X.156(54254), dst=X.X.X.X(53), length=73
*Jul 18 09:52:06.150: UDP: rcvd src=X.X.X.X(53), dst= X.X.X.156(54254), length=161
*Jul 18 09:52:06.151: UDP: sent src= X.X.X.156(54254), dst=X.X.X.X(53), length=97
*Jul 18 09:52:06.152: UDP: rcvd src=X.X.X.X(53), dst= X.X.X.156(54254), length=185
*Jul 18 09:52:06.152: Released port 54254 in Transport Port Agent for IP type 1
*Jul 18 09:52:06.153: UDP: Random local port generated 55980, network 1
*Jul 18 09:52:06.153: Reserved port 55980 in Transport Port Agent for UDP IP type 1
*Jul 18 09:52:06.153: UDP: sent src= X.X.X.156(55980), dst=X.X.X.X(53), length=72
*Jul 18 09:52:06.154: UDP: rcvd src=X.X.X.X(53), dst= X.X.X.156(55980), length=160
*Jul 18 09:52:06.154: UDP: sent src= X.X.X.156(55980), dst=X.X.X.X(53), length=96
*Jul 18 09:52:06.155: UDP: rcvd src=X.X.X.X(53), dst= X.X.X.156(55980), length=184
*Jul 18 09:52:06.155: Released port 55980 in Transport Port Agent for IP type 1
*Jul 18 09:52:06.156: CAPWAP Control mesg Sent to X.X.X.100, Port 5246
*Jul 18 09:52:06.156:           Msg Type   : CAPWAP_DISCOVERY_REQUEST
*Jul 18 09:52:06.156:           Msg Length : 102
*Jul 18 09:52:06.156:           Msg SeqNum : 0
*Jul 18 09:52:06.156: UDP: sent src=X.X.X.156(41188), dst= X.X.X.100(5246), length=154
*Jul 18 09:52:06.157: UDP: sent src= X.X.X.156(41187), dst= X.X.X.100(12223), length=128
*Jul 18 09:52:06.157: CAPWAP Control mesg Sent to X.X.X..172, Port 5246
*Jul 18 09:52:06.157:           Msg Type   : CAPWAP_DISCOVERY_REQUEST
*Jul 18 09:52:06.157:           Msg Length : 102
*Jul 18 09:52:06.158:           Msg SeqNum : 0
*Jul 18 09:52:06.158: UDP: sent src= X.X.X.156(41188), dst= X.X.X.172(5246), length=154
*Jul 18 09:52:06.158: UDP: sent src= X.X.X.156(41187), dst= X.X.X.172(12223), length=128
*Jul 18 09:52:06.159: CAPWAP Control mesg Sent to X.X.X.99, Port 5246
*Jul 18 09:52:06.159:           Msg Type   : CAPWAP_DISCOVERY_REQUEST
*Jul 18 09:52:06.159:           Msg Length : 102
*Jul 18 09:52:06.159:           Msg SeqNum : 0
*Jul 18 09:52:06.159: UDP: sent src= X.X.X.156(41188), dst= X.X.X.99(5246), length=154
*Jul 18 09:52:06.160: UDP: sent src= X.X.X.156(41187), dst= X.X.X.99(12223), length=128
*Jul 18 09:52:06.160: CAPWAP Control mesg Sent to X.X.X.101, Port 5246
*Jul 18 09:52:06.160:          Msg Type   : CAPWAP_DISCOVERY_REQUEST
*Jul 18 09:52:06.160:           Msg Length : 102
*Jul 18 09:52:06.160:           Msg SeqNum : 0
*Jul 18 09:52:06.160: UDP: sent src= X.X.X.156(41188), dst= X.X.X.101(5246), length=154
*Jul 18 09:52:06.161: UDP: sent src= X.X.X.156(41187), dst= X.X.X.101(12223), length=128
*Jul 18 09:52:06.161: CAPWAP Control mesg Sent to 255.255.255.255, Port 5246
*Jul 18 09:52:06.161:           Msg Type   : CAPWAP_DISCOVERY_REQUEST
*Jul 18 09:52:06.162:          Msg Length : 102
*Jul 18 09:52:06.162:           Msg SeqNum : 0
*Jul 18 09:52:06.162: UDP: sent src= X.X.X.156(41188), dst=255.255.255.255(5246), length=154
*Jul 18 09:52:07.194: Released port 68 in Transport Port Agent for IP type 1
I don't understand the reds lines messages
Excuse me for my english and thank you for help

On the wlc cli you can issue: debug client
If the client shows up in the wlc and under the monitor client ,the policy state of the client is in run, that means the client has successfully authenticated and is on the wireless. This means it must be a network issue. SO go to the monitor tab and click on clients and click on the client mac address. You will see the policy manager state and look to see if its in RUN.
Sent from Cisco Technical Support iPad App

My iphone 4s and ipad 2 both with 7.0.4 update will no longer connect to wifi but non-mac lap top has no issues

my iphone 4s and ipad2 both with 7.0.4 update will no longer connect to wifi.
About three days ago the ability to connect came and went and the connection never lasted more than 10-15 minutes; it has not been able to connect since last night. I do not think it's my wifi router as non-mac lap top has no issues. I have seem many similar questions posted.

Reboot your router by removing all power from it for about 15 seconds. Also, if your router still has its default SSID (such as LINKSYS, DLINK, NETGEAR, etc) change the SSID to something unique. Note that all other devices on your network will have to be reconnected if you change the name, but if the name is still the default that is most likely your problem.
If the SSID is not the default then the reboot should fix it.

My IPad cannot download live Tv from skygo. I have no problem with my lap top so I assume the broad band is okay. Can anybody suggest why the live streaming will not work on my iPad one.

My IPad cannot download live Tv from skygo. I have no problem with my lap top so I assume the broad band is okay. Can anybody suggest why the live streaming will not work on my iPad .

Are you using the Sky Go app to try and watch it ? If so are you logged in with your Sky account ?
If you are using the app then you could try closing the app completely and see if it works when you re-open it : from the home screen (i.e. not with Sky Go 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Sky Go app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work then you could try a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

HT4906 My ipad 4 is stuck. Icloud says it cannot access my account. It says go to settings. I went to the settings on my lap top but I can't access the settings on ipad. I pad gives me a choice of ignoring or going to settings. None work. frozen.

It tells me to review my account in settings. I tap on settings and nothing happens. My ipad is frozen. I can even shut it off. This icloud message stays on the screen and nothing works. I've looked at my settings on my lap top and everythings is okay. I bought the ipad in Palm Springs area. I can't remember if he set up I cloud for me there. Now I am in Canada. I updated my lap top to Lion so I would get I cloud, too. Should't the passwords be the same on both units when I access icloud. Something is not right. Do I throw my ipad 4 away! It won't do anything with this icloud message on the screen. Can't even cancel it. Can anyone help?

See if this helps you.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

The touch screen on my nearly brand new Pavillion lap top running windows 8 no longer works.

The touch screen on my nearly brand new Pavillion lap top running windows 8 no longer works. Cant use calibration tools as there's no response to touch. No option in control panal to turn on or off touch capability. I have no computer background so cant really get to technical. Is something simple turned on or off located in some mysterious place? F key or something? Bad machine? Thanks for any input. Sarah

http://www8.hp.com/au/en/drivers.html
I found the driver at the above link. I installed the driver, disabled my graphics card and rebooted. The touchscreen worked. Then I enabled the graphics card. So far so good. Hope I dont have to do this routine too often.
Good luck with it.

How to go in GUI mode of AIR-LAP 1131AG-A-K9 standlone

i am using above model of access point without controller.For that we tried to convert LAP to autonomous mode but didnt get success.Here is log viewer of tftp server.
Connection received from 10.0.0.1 on port 1024 [29/01 19:19:29.156]
Read request for file <c1130-k9w7-tar.default>. Mode octet [29/01 19:19:29.171]
Using local port 1112 [29/01 19:19:29.171]
TIMEOUT waiting for Ack block #1 [29/01 19:19:44.171]

What i understand you want to convert from Lightweight mode to autonomous mode .. without controller
Link to download tftp server
http://tftpd32.jounin.net
Link to download AP image you to upload:
http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875243
Here is the step that you can try :-
LWAPP to autonomus AP converstion steps
Here is a example steps for you:
Step 1 The PC you intend to use must be configured with a static IP address in the range of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1100-k9w7-tar.122-15.JA.tar for an 1100 series access point or c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1100-k9w7-tar.default for an 1100 series access point or c1200-k9w7-tar.default for a 1200 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, you must reconfigure the access point by using the Web-browser interface or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a0080209250.html#wp1040300
Hope this helps! ..
Pls rate if it resolve ur issue so that others can also benefit from these steps.
Thanks,
Manjeet Singh

WLC 5508 with LAP-1142n - Several Errors

Hello all,
I had installed a WLC 5508 with 7 LAP 1142n and 2 converted AP 1131abg.
I am seeing some errors relating 2 issues.
1st- One particular AP 1142 is disassociating and reseting the radios.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:1(802.11a) Operation   State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init.   Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:0(802.11b)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to   Init. Status:NA
Thu Oct 28 11:50:46 2010
AP 'AP3', MAC:   e8:04:62:23:ac:e0 disassociated previously due to AP Reset. Uptime: 1 days,   10 h 24 m 23 s . Last reset reason: operator changed 11g mode.
Thu Oct 28 11:50:35 2010
AP Disassociated. Base Radio   MAC:e8:04:62:23:ac:e0
Thu Oct 28 11:50:35 2010
AP's Interface:1(802.11a)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
Thu Oct 28 11:50:35 2010
AP's Interface:0(802.11b) Operation   State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
I had some search, and the new discovery cause, might be that the AP didnt know what WLC do associate, in a multi-controller environment. This is not the case. I only have one WLC in the same management vlan.
2st-The Radius server is beeing related in the logs as been deactivated. I raise the server time-out on Radius configuration option, but it still continues to do it.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 deactivated in global list
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 failed to respond to request (ID 172)   for client e8:06:88:51:c0:2b / user 'unknown'
Is this meaning the WLC stop sending request to the Radius Server ? We dont have BackUp Radius.
As far as i know, its always the same mac-address client that is associated to that error, maybe a iphone.
I had so many clients in that SSID and they are all working good.
The Radius server is a NPS from windows Server 2008
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
, and the client says that the medium response time is 0,02 sec, so im wondering why the controller is not getting response from Radius for a particular client?! My client also says, that didnt found any log related to that mac-address client ... what is weird...
WLC with last software available 7.0.164
Hope some one help me here.
Best Regards,
Bruno Petrónio

Thanks Scott,
I understand what you are mentioning, and i really didnt do it yet.
I realize that the primary controller was not configured on the
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
Is this mandatory for a 1 controller only ?
No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
Next step ... i will change it to another one's place/pathing cable.
Regarding the Radius messages... any ideas ?
I'm already on 30 sec's of server timeout.
Best Regards,
Bruno Petrónio

Cisco AIR -LAP-1142 status led continuosly blinking green

hello all,
I have implemented around 46 access points (AIR-LAP-1142) in a customer site and i can see that the led of some of the access points are continously blinking green and no clients are associated to these access points. I have a WISM which has two controllers in it. I can see the particular aps to be joined in the controller. But my question is that why its not giving me any signal. Please help me as this is very urgent!!.. even if am under the access point the signal is not there. I checked the radio status of the aps and its up. The WLANs are activated from the controller also. Please help mee....!!

continously blinking green
This could mean that the AP hasn't joined the WiSM yet.
Can you console into the AP? If you can, reboot the AP and post the entire power up and bootup process and include the "sh logs".

HREAP on LAP reboot

Similar Messages

Maybe you are looking for