I cant connect to my cisco router with a computer using wireless...

When ever i try and connect to my wireless router is says, "This network is marked as Hidden and is either out of range or this computers settings dont match the router".
This is driving me crazy i just want to use my internet...
Please help me, ye i know how to get into my router setting using the default gateway i just need to know what to change...

Log on to your router and go to wireless. Enable ssid. If it is showing Linksys, change it to something else. Now click on Wireless security and write down all the settings. Make sure they match the ones in your computer under wireless connections.
Greetings from Northern Ontario, Canada

Similar Messages

Multiple WAN connections all through one router with load balancing?

I am setting up a network in my dormatory for myself and about 20 friends. about half of us have DSL connections at the moment. Is there a way to have all the DSL connections (possibly run through cheap home DSL routers) all connect into a cisco router that then acts as the gateway for our entire network? woudl it be possible for each internet request to go out over the connection that has the least load AND also be able to use some sort of load balancing, so one user cant use all of the outgoing/incoming bandwidth?
If you have any ideas please let me know

Hi Ian,
To get this working, you would either need to use something like PPP to bundle your links together or use a dynamic protocol.
In bundling the links, you could make them appear as one link, with a single IP address each end and the router takes care of distributing the load. To implement this though, you would need control of both sides of the link, or be terminating with one carrier who is happy to implement this for you.
The second is to use a dynamic protocol (such as eigrp, ospf, etc), which can build up a map of the network to router from point a to point b. For this you also need control of the link.
I can't think of another method, unless you can control the link from both sides. Your other option it to pool your money and buy a larger link or a leased line. If you bought a leased line or two, your carrier would be more than happy to talk to you about routing over that, but generally you're looking at mega bucks for that.
HTH,
Mark

Connecting Apple TV to router with ethernet cable

help connecting Apple TV to router with ethernet cable

The process is transparent. I have done it before.
Now, it gives me an error message when I try Wi-Fi:
"There was a problem connecting to the network. Check your settings and try again.(5)"
When I try the ethernet cable connection it won't let me do automatic or custom.
I unplugged and replugged the Apple TV box but don't know how else to trouble shoot the lack of connectivity.

Connect more than 3 router with WDS

hi,can i connect more than 3 router with WDS,in need to connect 8 wifi router with wireless, plz help me,Tnx

Its not possible you can try the same with access points.

Help to connect Microoft Remote Dextop (win7) with Iphone 5 using RD client

Help to connect Microoft Remote Dextop (win7) with Iphone 5 using RD client Hello, I can connect my iphone 5 to my laptop(windows7 OS) with RD client while My iphone is also connected with my laptop's wifi hotspot. And i can remotely control my laptop with the iphone nicely while I am in the laptop's wifi range. Is it possible to control my laptop from iphone while my phone is not connected to laptop's wifi hotspot???? I use 3G internet in my phone while I go out of home.

I have no issue using cellular data when I remote in from my iphone with the RD client.
Have you tried using cellular data to remote in?

I can not get my Ipod to connect with my computer using a usb cord

I can not get my Ipod to connect with my computer using my usb cord ?

Hi starhalcomb,
I'm sorry to hear you are having issues with your iPod touch. I also apologize, I'm a bit unclear on your exact configuration. If you are having issues with your iPod touch not being recognized in iTunes when you connect via USB, you may find the information and troubleshooting steps outlined in one of the following articles helpful:
iPhone, iPad, or iPod not recognized in iTunes for Windows - Apple Support
If you don't see your connected device in iTunes for Mac - Apple Support
Regards,
- Brenden

I cant connect to my itunes account on my computer or my iphone.

cant connect to itunes on my phone or computer please help

What do you think you could accomplish if you could do this...?
You can sign into your iCloud account by going to www.icloud.com from a web browser on any computer.

I have problem to connect the I-pad 2 with my computer. I-tunes does not synocronize my IPad

I have problem to connect the I-pad 2 with my computer. I-tunes does not synocronize my IPad

lewis137 wrote:
it dossent matter now ill just reformat my computer
If you like

Can I communicate single PXI chassis with multiple computer using MXI

Can I communicate single PXI chassis with multiple computer using multiple MXI cards
we are using cvi with MXI we want to share channels for other computers Can we do with mxi

Yes this is possible when you use a PXI controller. Attached is a screenshot showing a possible configuration.
Jacob K || Applications Engineer || National Instruments
Attachments:
PXIMaster.png ‏20 KB

Can I interface a normal DC motor with a computer using LabView?

I am trying to find a DC motor that can be interfaced with the computer using LabView. Is that possible? If so, HOW?

There are many ways to control DC motors from LabVIEW. National Instruments provides plugin motion control boards like the PCI-7342 that are capable of controlling 2 to 8 stepper or servo motor (DC) axes. Additionally you need a drive for power amplification.
You find lots of very good information about controlling motors from LabVIEW with NI motion control hardware under this link:
http://www.ni.com/motion/
The NI motion control boards have lots of high level features like position control, interpolation modes, contouring, onboard programming and so on. Your request is very brief so I can't tell if this level of control is oversized for your application or not. If you simply want to turn a DC motor on or off there will be cheaper methods to accomplish that.
Best regards,
Jochen Klier
National Instruments Germany

HT203311 I am use homesharing, but cannot sync the main library from the secondary computer to an iphone. It shows the entire libaray on the computer, but only shows a few songs when I try to sync iphone with the computer using homesharing.

I am use homesharing, but cannot sync the main library from the secondary computer to an iphone. It shows the entire libaray on the computer, but only shows a few songs when I try to sync iphone with the computer using homesharing.

See Recover your iTunes library from your iPod or iOS device.
tt2

HT5569 Yesterday, my ability to receive gmail, facebook, safari,etc.ceased on my ipad2. The wifi shows it is connected and the cisco router works ok with another computer connection. Can anyone tell me what I need to do with ipad in order to get it worki

Yesterday, my ability to receive gmail,facebook,safari,etc. ceased to perform The wifi connections shows that it is connected but I cannot get through the internet . I use a Cisco router and it is working fine with another computer and also a printer. I contacted the internet provider and they show the ipad at the router but not out through the internet. Also, yesterday my wife eliminated some programs(games,etc) from the ipad. Anway, I am thinking I am missing some setting that is not turned on as everything seems to be working fine.
Any suggestions?

Settings > General > Reset > Reset Network Settings

Trouble connecting Cisco router with cable modem for Internet purposes

So I am requesting help from the Cisco community on this issue as the cable company states there equipment is working fine. At all my facilities I have a guest Internet service setup through a local Internet provide to provide Internet services to the residents and guests. I have the cable modem usually a Motorola SBG6580 or a SMC 8014 (both provided by cable company) connected to my router on a FE or GE interface. I am using static IPs and using the cable modem just as a modem (bridge mode). Over the past several months these connections have just stopped working. I have not made any drastic changes to my router configs; however, the cable company has updated the firmware on these modems. I am wondering if that could affected how the modem and router talk. I was told by the cable company that the modem sees the Cisco router but that the port is inactive. My router shows the port is active and traffic passing. Does anyone have any ideas that could point where the problem lies? I will post a basic config to one that currently does not work. I am using a VRF to route a certain group out, using NAT. Please let me know if I need to post additional info. Any help would be greatly appreciated.
Cisco CISCO2911/K9
Version 15.2(3)T1
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname 1204RTR01
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.152-3.T1.bin
boot system flash0:c2900-universalk9-mz.SPA.151-3.T.bin
boot-end-marker
card type t1 0 0
logging buffered 64000
aaa new-model
aaa session-id common
clock timezone cst -6 0
clock summer-time CDT recurring
no ipv6 cef
no ip source-route
ip vrf 5
rd 5:1
ip multicast-routing
1
ip dhcp pool Guest
vrf 5
network 10.51.XXX.0 255.255.255.0
default-router 10.51.XXX.XXX
dns-server 209.18.47.61 209.18.47.62
ip flow-cache timeout active 1
no ip bootp server
no ip domain lookup
ip cef
multilink bundle-name authenticated
application
global
service alternate default
license udi pid CISCO2911/K9 sn FTX1508AHTM
hw-module pvdm 0/0
redundancy
ip tcp synwait-time 10
interface GigabitEthernet0/0.5
description Guest VLAN
encapsulation dot1Q 5
ip vrf forwarding 5
ip address 10.51.xx.xxx 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/2
description Guest Intenet access
ip vrf forwarding 5
ip address 24.242.182.182 255.255.255.252   <--Cable company IP, Modem IP is 24.242.182.181
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
ip forward-protocol nd
no ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 9 interface GigabitEthernet0/2 vrf 5 overload
ip route vrf 5 0.0.0.0 0.0.0.0 24.242.182.181
access-list 9 permit 10.51.204.0 0.0.0.255

Ok, mysteriously this location just started working yesterday, but I still am dealing with seven others and I really would like to know what is going on. I will give you everything you may need and let me know.
Config:
version 15.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname 1112RTR01
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.152-3.T1.bin
boot system flash0:c2900-universalk9-mz.SPA.151-1.T.bin
boot-end-marker
aaa new-model
aaa session-id common
clock timezone CDT -6 0
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
no ipv6 cef
no ip source-route
ip vrf GuestVRF
rd 5:1
ip multicast-routing
ip dhcp pool Guest
vrf GuestVRF
network 10.51.112.0 255.255.255.0
default-router 10.51.112.1
dns-server 209.18.47.61 209.18.47.62
ip flow-cache timeout active 1
no ip bootp server
no ip domain lookup
ip cef
application
global
service alternate default
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0.5
description Guest VLAN
encapsulation dot1Q 5
ip vrf forwarding GuestVRF
ip address 10.51.112.1 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface GigabitEthernet0/1
description Guest Internet (Time Warner Connection)
ip vrf forwarding GuestVRF
ip address 97.77.116.234 255.255.255.252
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
ip forward-protocol nd
ip nat inside source list 5 interface GigabitEthernet0/1 vrf GuestVRF overload
ip route vrf GuestVRF 0.0.0.0 0.0.0.0 97.77.116.233
access-list 5 permit 10.51.112.0 0.0.0.255
control-plane
end
router#sh ip arp vrf GuestVRF
router#Internet 97.77.116.233           2   f80b.bee7.e09f ARPA   GigabitEthernet0/1
Protocol Address          Age (min) Hardware Addr   Type   Interface
Internet 97.77.116.234           -   8843.e13c.8d99 ARPA   GigabitEthernet0/1
router#ping vrf GuestVRF 97.77.116.233
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 97.77.116.233, timeout is 2 seconds:
Success rate is 0 percent (0/5)
router#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 8843.e13c.8d99 (bia 8843.e13c.8d99)
Description: Guest Internet (Time Warner Connection)
Internet address is 97.77.116.234/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:10
Input queue: 76/75/15/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 3000 bits/sec, 7 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
     81 packets input, 4860 bytes, 0 no buffer
     Received 81 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 12 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     16 packets output, 1193 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out
router#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 8843.e13c.8d99 (bia 8843.e13c.8d99)
Description: Guest Internet (Time Warner Connection)
Internet address is 97.77.116.234/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:42
Input queue: 76/75/67/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 3000 bits/sec, 7 packets/sec
30 second output rate 1000 bits/sec, 2 packets/sec
     408 packets input, 24480 bytes, 0 no buffer
     Received 408 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 61 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     72 packets output, 5669 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out
I am receiving packets in and out of the interface but I cannot ping the modem through the VRF.
router#sh ip nat translations
Pro Inside global      Inside local       Outside local      Outside global
udp 97.77.116.234:3169 10.51.112.39:3169 209.18.47.62:53    209.18.47.62:53
udp 97.77.116.234:8534 10.51.112.39:8534 209.18.47.61:53    209.18.47.61:53
udp 97.77.116.234:12244 10.51.112.39:12244 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:14002 10.51.112.39:14002 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:23623 10.51.112.39:23623 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:24489 10.51.112.39:24489 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:24550 10.51.112.39:24550 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:27458 10.51.112.39:27458 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:28603 10.51.112.39:28603 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:37404 10.51.112.39:37404 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:53942 10.51.112.39:53942 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:58125 10.51.112.39:58125 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:64797 10.51.112.39:64797 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:56925 10.51.112.52:56925 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:56925 10.51.112.52:56925 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:62342 10.51.112.52:62342 209.18.47.62:53   209.18.47.62:53
tcp 97.77.116.234:36559 10.51.112.69:36559 199.167.177.46:1227 199.167.177.46:1227
tcp 97.77.116.234:48895 10.51.112.69:48895 54.195.253.126:5223 54.195.253.126:5223
tcp 97.77.116.234:58385 10.51.112.69:58385 54.195.243.137:5223 54.195.243.137:5223
Pro Inside global      Inside local       Outside local      Outside global
tcp 97.77.116.234:58658 10.51.112.71:58658 31.13.66.165:443 31.13.66.165:443
udp 97.77.116.234:3066 10.51.112.72:3066 209.18.47.62:53    209.18.47.62:53
udp 97.77.116.234:3884 10.51.112.72:3884 209.18.47.61:53    209.18.47.61:53
udp 97.77.116.234:6656 10.51.112.72:6656 209.18.47.61:53    209.18.47.61:53
udp 97.77.116.234:11194 10.51.112.72:11194 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:11774 10.51.112.72:11774 209.18.47.62:53   209.18.47.62:53
Let me know if you need anything else. I need to figure this out and I just don't get it because the other site wasn't working a few days ago and all of a sudden it is working again but others are still not.

Wireless non-cisco router with aironet 1242 repeater.

Hello everyone. I'm a newbie here. I just started learning about cisco devices. Sorry if my question seems stupid.
I have a problem. A friend gave me an AP aironet 1242 and he wants to use it as a repeater for his wireless non cisco router.
Is this possible? And if it is how can i do it with simple steps.
Thanks in advance!

Thanks for the quick response Scott. I 've read this quide before i post.
The problem is that i can't connect with serial to the ap. So i can't use commands.
I can connect with ethernet and see the ap interface. When i go and make the radio0 work as a repeater it shows interface down. What i want is simple steps of how to configure it from the interface.
Sorry again.

Cant connect on xbox 360 chat with my friend

i cant connect with just one of my friends on xbox 360 is there like a gaming mode i change to make so i can?

Ok we have done everything we can think of on our WRT54G router including
Set static IP address on the xBox
Enabled DMZ with xBox static IP address
Port forwarding NOT enabled
MTU at 1364
QoS "Highest" for Mac address of Xbox 360
Security , "Filter IDENT (Port 113)" is the only one checked
Upgraded firmware
and either hard wired or wireless connected get "Can't connect to the Xbox LIVE Party."
every thing else works fine.
Only way it works is to connect the xBox directly to the DSL Modem
Any help?

I cant connect to my cisco router with a computer using wireless...

Similar Messages

Maybe you are looking for