I have AirPort Extreme and cannot connect to the internet with a land line but the WiFi works

I have an AirPort Extreme and have been using for several months successfully, but as of two weeks ago, the line that I have hooked up to my desktop no longer provides internet service, but the WiFi works fine for the I-Pad and I-Pod.
I have checked with my service provider and my modem works successfully hooked up the the AirPort extreme or directly to the PC. When I am hooked in from the modem directly to my PC, I have internet for my desktop, but of course no WiFi.
If I connect the Modem to the Router and the router to my desktop, I have WiFi, but no internet service to my desktop.
I have replaced the network cable but to no avail.
Any suggestions?

It appears that there may be something amiss with the Ethernet switch that is built-in the 802.11n AirPort Extreme Base Station (AEBSn) or its configuration settings may be incorrect. I assume that you also tried using the other LAN ports on the AEBSn and the outcome was the same ... no Internet access via a wired connection.
One thing to try is to change the Ethernet adapter settings on the PC. It is possible that its current settings may be appropriate when connected directly to the Internet modem, but may be off for connecting to the AEBSn. If your PC's Ethernet adapter has options to control Speed, Duplex, & MTU, I would change these to the following respectively: 1000 Mbps, Full duplex, & 1500

Similar Messages

If I have an airport extreme and a time capsule is it possible for seamless switching between the 2 when a signal is weak or drops Main reason is as I move from my first floor to my attic office and would like to place one (airport extreme)downstairs and

If I have an airport extreme and a time capsule is it possible for seamless switching between the 2 when a signal is weak or drops
Main reason is as I move from my first floor to my attic office and would like to place one (airport extreme)downstairs and time capsule upstairs to get complete coverage

In theory, yes. If you configure the two base station into either an extended or roaming network configuration, you should be able to walk a laptop between routers and the laptop should attempt to connect/reconnect to the base station providing the stronger signal ... but, in reality, this is not always 100% true.

I have airport extreme and just purchased a D-Link DCS-932L home network camera. D-Link says I need UpNp but the extreme doesn't support this. Can I use port mapping? if so anyone know how to set that up? thanks

I have airport extreme and just purchased a D-Link DCS-932L home network camera. D-Link says I need UpNp but the extreme doesn't support this. Can I use port mapping? if so anyone know how to set that up? thanks

Since the D-Link DCS-932L is accessible on the local network via a web browser, you should be able to access this camera from the Internet if your router has a publically accessible Public IP address. If your ISP provides you with a dynamic Public IP address, you may want to use a DDNS service to make it easier for you to locate your camera whenever your ISP changes your IP address.
Start the AirPort Utility > Select the 802.11n AirPort Extreme Base Station (AEBSn).
Select Manual Setup.
Verify that Connection Sharing = Share a public IP address is selected on the Internet > Internet Connection tab.
Select Advanced, and then, select the Port Mapping tab.
Click the plus sign to add a new port mapping.
For Service, leave the default; this will change to "Custom" once you start entering port values.
In the Public UDP Port(s) and Public TCP Port(s) boxes, type in a 4-digit port number (e.g., 8888) that you choose. In the Private IP Address box, type the internal IP address of your camera. In the Private UDP Port(s) and Private TCP Port(s) boxes, enter the appropriate port values that should have been provided to you by the camera manufacturer. Click Continue.
In the Description box, type a descriptive name like "Internet Camera Access," and then, click Done.
Click on Update.
To connect to the shared Camera from a remote location using a Mac or PC:
Start your favorite web browser.
Enter either your Public IP address or DDNS-provided Domain Name, followed by a colon and the Public port number that you choose in step 7 of the previous procedure. For example: http://123.123.123.123:8888 or http://www.mydtdnsdomainname.com:8888

I am trying to log onto a Mac Mini I haven't used in awhile and I forgot the password. I am trying to reset the password with my apple ID but the computer keeps saying the Apple ID and the password are incorrect whenever I know they are.

I am trying to log onto a Mac Mini I haven't used in awhile and I forgot the password. I am trying to reset the password with my apple ID but the computer keeps saying the Apple ID and the password are incorrect whenever I know they are, as I am using the exact same ID right now.
I have switched my password in the past, so my theory is my mac mini thinks that my password has not changed and it will not update because The Wi-Fi password has also changed so it cannot connect to any servers...Does that sound like I am on the right track?
Is there a way to update my Wi-Fi password (saved into the computer) without logging on?

If the user account is associated with an Apple ID, and you know the Apple ID password, then maybe the Apple ID can be used to reset your user account password.
Otherwise, boot into Recovery by holding down the key combination command-R at startup. Release the keys when you see a gray screen with a spinning dial.
When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar.
In the Terminal window, type this:
resetpassword
That's one word with no spaces. Then press return. A Reset Password window opens.
Select your boot volume if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
You should now be able to log in with the new password, but your Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as your login password), there's no way to recover it.

Issue with Airport Extreme and 100mbps connection

Hi,
I have just upgraded my connection to 100mbps. Using a ARRIS TM 502G cable modem and the Airport Extreme I am able to get the 100mbps connection via either ethernet or wifi on my main MacBook Pro. However, the Mac Mini in the loungeroom (10 metres away from the Airport Extreme) is only getting speeds of around 25mbps.
Does anyone know why this might be or what I can do to resolve it?
Thanks,
Matt

The Mini was connecting at 20 - 25mbps via wifi.
The Macbook Pro was connecting at 80 - 90mbps via wifi (when in same room as Airport Extreme) and getting anywhere from 80 to 140mbps via a wired connection.
I've moved the Airport Extreme so it has the best "line of sight" to the Mini, and also disconnected a cordless phone I had in the room which was interfering with the signal.
After these changes I'm able to get speeds of 30 - 45mbps on the mini and similar speeds on my macbook if I move it next to the mini. It looks as though that's the best I'm going to be able to get without hard wiring the mini - which is disappointing ... unless of course you clever people have any other ideas?

TS1253 i have airport extreme, and printer works with my imac, but not with my mac book pro??

i tried setting up the printer under my wireless network only, and using the printer information, tried both and nothing works, my imac's same settings for the printer, and just cant get it to work.
i am ussing airport extreme, and it shows printer conecting etc. but then it says not programed correctly and it fails.
i dont know what else to try, i have followed every step on the manual, and nothing works..
someone help me

Could you open System Profiler on the iMac and the MBPro and select the Printers entry. Then in the top right pane you can select the printers entry and the bottom right pane will show information about your setup. Can you copy this information from both Mac's and paste back here.

I have airport extreme and have windows 2003 what program do i down load for airport utility

can any one help i tried one but was for windows 2007 no good need it for windows 2003 i have airport extreme just bought it today

Ok thanks for the info - I am only familiar with Windows so I am going to suggest a typical setup using your Toshiba laptop - you can then use the network with any device - tell me if this works for you.
Determine which version of Windows that your Toshiba uses.
Go to http://support.apple.com/downloads/#peripherals
You will be downloading Airport Utility
Download version 5.6.1 for Windows 7 or
Download version 5.5.3 for Windows XP or Vista
Once you have done this let me know if you will be using this Extreme as your primary router after your modem or is your modem also acting as a router or do you have another router anywhere in your network

I have a new Macbook Air 2012, Apple TV 2 and I have tried wired and wireless connections both result in stuttering during video airplay to the ATV2.

I have a new Macbook Air 2012, Apple TV 2 and I have tried wired and wireless connections both still result in stuttering during video airplay to the ATV2.
I have even bought a new Airport Extreme Router just to confirm it is not the router and it still didn't help.
I have brought all items in the same room with wired connections and still same issue.
I was thinking maybe ATV 3 might help since it has 2 wifi antennas and faster processor.
Have tried everything I could think of.
This was one of the main reasons I bought a Macbook Air for this airplay feature. Very frustrated.
Any thoughts; any other suggestions would be greatly appreciated.
Thanks

Thanks for the suggestion.
I also disabled Norton Firewall and restarted the Air and Now I'm able to use Air Play.
I know that the Apple remedy said that to do that in the support article, but I totally forgot I had that enabled..
It actually works. I can even stream to the Apple TV now through my MacBook Air.
BTW, Go into setting under the ATV, and click on update...you'll see that there was another update avaialble for the last gen of ATV...
It does have to restart twice..I guess once to download and and nother to apply.

My Ipad 3rd gen kept shutting off and we would have to restart and log back on to internet with password. So backed up to icloud and did a restore. It could not complete the restore. No luck at Genius bar. Can trade for a new one for 299. any ideas to fix

Ipad 3rd gen kept shutting off. Had to restart and log back on to internet with password. backed up and did restore.
could not complete. Took to Genius bar and they could not either. Said we trade with $299 for another one.is there
someplace to get these things repaired. It was 4 months out of warranty.

Yet another quick follow up to something I have stumbled upon with this issue. If I connect to my Airport Extreme on the 5Ghz channel, Dictation continues to have issues. However, when I switched to the 2.4Ghz channel dictation has been working great now for a while.
The dictation option is still missing under General>Settings>Keyboard however.
Not sure at all what one would have to do with the other? but hey, if it's working then I'm going with it for now. :-)

Need help with Airport Extreme and my new Verizon Fios Internet connection

I just got the Fios install, and the tech and I couldn't figure out how to use my Airport Extreme as my wireless connection. I'm not real tech savvy (and I've only been a Mac guy for about 18 months). My current arrangement is the basic Verizon setup with the Airport out of the loop. How can I go about moving from here back to using my Airport Extreme? I need the range! Thanks in advance for your help.

Have you tried resetting and reconfiguring the AirPort Extreme base station (AEBS)?
Are you using OS 10.5 or OS 10.4 or earlier?
Are you using the round 802.11b/g AEBS or the square 802.11b/g/n AEBS?
If you are using OS10.5 OR the square 802.11b/g/n AEBS you should refer to "Designing AirPort Networks Using AirPort Utility" (direct PDF link).
Otherwise you should refer to "Designing AirPort Extreme Networks" (direct PDF link).

Airport Extreme and Express - connecting both via Powerline?

Hi
Recently moved to Virgin and now have a Superhub 2 Modem/Router. However, still want to use my existing Airport Extreme (4th Gen) and recently purchased Airport Express (2nd Gen).
I can put the Superhub 2 into Modem only mode so the Airport Extreme is only router. I currently extend the network around the house with the Airport Express.
Is there anyway I can connect the Extreme to the Express via a Netgear Powerline? If so, will this work with both 2.4 and 5.0 networks.
Thanks in advance.
Matt

Is there anyway I can connect the Extreme to the Express via a Netgear Powerline? If so, will this work with both 2.4 and 5.0 networks.
Yes on both. Note however, when interconnected by Powerline adapters, it would be the same as though they were connected by Ethernet. The type of extended network would not be an "extended" network but a "roaming" one. Both basically do the same thing.

I have a MacBook and cannot connect to App Store. I have no problem with the internet connection. I want to be able to buy the apps that are available for my computer. The date, time and location are all correct - all the suggestions have failed

I have a MacBook - I am unable to connect to App Store - I have no problems using the internet to connect to anything else. I have checked out all the suggestions - Apple Preference and time, date, location etc. they are all correct. I cannot think what else I should do. Any suggestions please Cynthiafromgrayshott.

If you don't see any messages, not have anti-malware running or the Firewall on, try installing the Mac OS X 10.6.8 Update Combo
It's ok to do this even though you are already running v10.6.8 (according to your profile).
Restart your Mac after the combo in installed, try the App Store.
Also... if you have an app called Little Snitch installed, that can prevent a connection to the App Store.

Using airport extreme card to connect iPhone to internet of mac ?

Is it possible to use a mac as wireless"base-station" for a iPhone by using an airport extreme card , if the mac is connected only by wire?
I created a network on my mac and my iPhone is connected to it, but it says the network is not connected to internet.
So can I connect the airport extreme card on my mac to the ethernet of my mac by changing the network settings on my mac?

Read here:
http://computers.tutsplus.com/tutorials/how-to-share-your-macs-internet-connecti on--mac-60309

I bought my Iphone 4 2 days ago and I cannot recharge the battery..I tried all the night (with Iphon4 swict on) but the battery levels show alwasy 24%??????

How to recharge the battery for I-phone4????????????

Hello Marynoemi
Have you tried reset all settings
settings > general> reset > reset all settings
if that doesn't work try following this http://support.apple.com/kb/HT4137?viewlocale=en_US&locale=en_AU
you should probably also try another cable and charger if you have one and if that doesn't work call apple.

Airport Extreme card cannot connect in the 10.4.2 G5

We have installed the extreme card and it sees the network, and others, but simply will not connect " There was an error etc" anybody any ideas.....

IMac G5, or PowerMac G5?
For either model, make sure the internal antenna connector is FULLY seated into its socket on the Airport card - this takes a fair bit of force.
If a PowerMac G5, make sure the external T-shaped antenna is connected to its socket on the rear panel.

I have AirPort Extreme and cannot connect to the internet with a land line but the WiFi works

Similar Messages

Maybe you are looking for