IMac i7 Quad-Core firewire port and video camera
Has anybody tried to detect a video camera connected to the firewire 800 port?
I have already tried with two PRO tape-based DV video cameras: SONY PD170 and PANASONIC AG-HVX200E with no results. The same models do not have any problem with iMac 27" Core Duo 2.
Apple care protection plan has been useful only to know that if my iMac firewire port can handle an external Hard Disk, as it does, the compatibility with the camera is not a problem of Apple, but simply mine.
Any suggestion? Any help to find official pages by Apple with technical specification about firewire port and protocol of the new iMac 27" i7?
Thanks, Carlo
Message was edited by: Carlo G
Today my Mac has finally been fixed. I had to send it to Milano, to SATA srl, where they have replaced the logic board. Now I can import video from my video camera using the FireWire port. Thank SATA!!!
Message was edited by: Carlo G
Similar Messages
-
Capturing Video on New iMac with only 1 FireWire Port
Using one of the new Apple iMacs, what is the best way to capture digital video footage (Mini DV) into Final Cut using an external drive as your scratch disk? The iMac offers only one FireWire 800 port. Is it advisable to connect the camcorder to the FireWire port and use a USB 2.0 to connect the external drive? Or can you connect the drive via FireWire 800 and connect the output of the camcorder to one of the other Fireiwre ports on the drive? In this instance I am using a Lacie Rugged Hard Disk that has one FireWire 800, one FireWire 400, and one USB 2.0 port.
They often do not play well with other firewire devices on the same bus. And since all the firewire ports on a Mac are on the same bus, it can lead to incompatibilities during capture. On some computers they work fine, on others they collide.
Try it and see if it works for you. If it does, be happy. If it doesn't, you'll have to do the external drive/camera shuffle.
It goes like this:
• turn off the computer and all connected devices,
• disconnect the external drive
• connect the camera using a FW800 to FW400 cable
• turn on the camera
• turn on the computer
• launch FCP, set the capture scratch folder to the system drive then capture
• shut down the computer and the camera
• disconnect the camera and connect the external drive
• turn on the drive
• turn on the computer
• launch finder and move the captured files from the system drive to the external
• launch FCP and reset the capture scratch folder to the external drive
• open your project and reconnect the media.
Or, use a different (non-Canon) capture device.
Or, get a computer that has multiple internal drives or has expansion capabilites so you can add a firewire card to create a second independent firewire bus for the camera.
Good luck,
x -
I bought iMac 27 quad core i7 last June. Last month i have noticed lots of dark patches on the screen and now they are growing more. i bought this from US but now i have moved to Kuwait. How much it cost to replace the screen?
Mac and Mac models are picky about the RAM the Mac needs to see and use.
As you have found out, the 1067 speed RAM will not work in your year and model iMac.
You need the 1333 speed RAM.
If, you can return the RAM for a refund, do it!
If not, try online Mac RAM source and seller Crucial memory. They have a table that matches your Mac to the correct and reliable RAM. You may need to contact them to see whether or not they ship to South Africa, though.
If Crucial dpesn't work out, here's the specs for your year and model iMac that you need to seek out and purchase.
Maximum Memory
32 GB (Actual) 16 GB (Apple)
Memory Slots
4 - 204-pin PC3-10600 (1333 MHz) DDR3 SO-DIMM
Good Luck! -
Value of upgraded RAM in imac 27" quad core
Friends,
I have a 27" imac i7 quad core on order. I do a fair amount of editing in FCE and Aperture. Does anyone have any sense of whether there would be a noticeable difference in processing speed if I upgrade the RAM to 12gb, versus 8gb or 4gb? Are there any RAM benchmarks out there?
Thanks!
SteveWell, yes, mixing & matching is fine, your system will run (of course, that assumes you have the correct kind of RAM ).
Mac memory architecture supports dual-channel memory access. Depending on the model (G5, Intel Core/Core2 Duo/Quad Core), it uses 64-bit data paths or 128-bit paths. If the DIMMS are matched, you get the benefit of the maximum speed of dual-channel access. If the DIMMS are not matched the system has to revert to asymmetric mode, which is slower. How much slower depends on all sorts of things.
Understand, that's not a complete technical explanation, but it hopefully makes the essential point. More RAM trumps matched DIMMS. However, you made a significant investment in your Core i7 iMac, if you're going to add RAM, why not buy matched DIMMS? -
Why would the Firewire Port and/or External DVD-RW suddenly not work?
Hi, it's me again. I swear, I must be destined to just use Windows machines...
Anyways, I have a used/refurbished iBook G3 500MHz 320MB RAM Dual USB (1 Firewire)laptop running OS 10.2.8 that I bought a few months ago. I went and purchased an external Firewire/USB 2.0 DVD-RW drive as I only had a CD-ROM drive on my machine and I wanted the option to burn CD's or watch/read data from DVD's (I know that with my slow processor writing DVD's -other than data- would be a stretch and have other machines to do that with anyways so it wasn't a concern really). I received it and installed it, also installed the free version of Toast that came with it, and the drive worked fine. I have not needed to use the drive since then and have not used the laptop much at all since then really, but I do need to say that I did end up adding a new user account, though I can't remember if I changed the original Admin account and then still have the one I created myself when I first started the laptop after I bought it (had a fresh install of Jaguar on it, but I have no disk to re-install with if needed) or if I created a separate (new) account and ended up deleting the Original Admin accout (I know in Windows, you cannot delete the original Admin account but I do not know if that is the same for OSX or not). I did this as I wanted a master Admin account that I just wouldn't really use and then wanted the other as my main account (and use it to connect to my home windows network) and for some reason it would not let me put a check in the box to allow that account to do so (from either Apple or my user accounts) and so I know that my main user account now is set up to allow it (was it the old Apple user account or a new one, I can't remember- sorry).
Ok, so that is the back story to my problem, which happens to be this:
I just bought a new chip of RAM (512MB to make it a machine with 576MB RAM total) and as I had been looking at getting OSX Tiger (but didn't want to do it without the extra ram and had been considering Panther instead as well), I thought it was necessary if I wanted to not bog down my machine. I bought the Install Disks on DVD for Panther, as well as an upgrade disk (DVD again) for Tiger, therefore letting me use the External Firewire DVD-RW to install Panther, and if I liked I could go ahead and upgrade to Tiger (and if I didn't like it too much, or it slowed things down too much etc, then I could always go back to panther and have both available for future options). The extra RAM coming in handy here definitely.
So I was going to install the RAM today, and decided to go ahead and test out the External DVD to make sure it could boot from it (before making any changes to my system) and then go and install the RAM, and after that, install Panther to start... But I plugged all the cords and cables in, used my laptop with AC power even, and I could not get the External to show up at all... (kinda like the very current post right below mine but for the G4- it worked before, but now the firewire External just does not show up).
I only have USB 1.1 on this laptop obviously, and I don't even know if you could do a boot from an external with USB 2.0 if my laptop had it (the DVD player does). I was recommended to boot with an external firewire DVD or firewire to another machine with DVD capabilities to do the install. So my problem right now is getting slightly bigger, as of course, I can't seem to momentarily find the stuff that came with the External (spare USB cable to check and see if the laptop will recognize it at least with that and to show it is the firewire that is not working properly, or the disk that I used to install it -might have been only used to install Toast free version if it didn't need any drivers, but I don't know where that or the instructions for installation sheet currently is -- I am looking for it, but I have switched bedrooms just last week and I also seem to be missing a few other Windows laptop disks as well so there is a good chance that they are all together, I just need to figure out where, heh.)
I am waiting currently before installing the memory, though if I don't get the External working tonight, I may go ahead and do it first as at least I will have more memory on my laptop then, until I can get other stuff functioning and be able to do the Panther install.
But my main question is, is there something that would cause an installed external to suddenly not show up in OSX? Since I hadn't used it since that one day, and it was unplugged from the laptop itself, would that end up doing it, or more likely, the changing of the user accounts (though I have been trying to test it with different types of media and through both of my user account (which are both "admin" ones), though I do still have one of those being an account that was on there when the External DVD was first installed, so it really shouldn't have done this at all (one would think). So how big of a chance is it that the firewire has somehow gone dead and this is the main culprit to my wasting the past 4 hours on this???
I am currently scavenging around for an extra USB cable to try and test the External that way and will post the results when I can... I love the look and idea of macs, now I have a mac and want to upgrade it even, but why is it that whenever I attempt to use it after having not used it for a bit (and try to make the iBook feel better by using it more as I am sure it feels sad and alone sitting on the shelf while my Windows Laptop gets more attention), or try to fix it when it can be made better (and therefore used more often), the mac (all macs really), just seem to get all pissy and cause problems and make me spend hours upon hours trying to get things to work again??? You have to admit it, I am "mac cursed"... sigh I can program in 4 or 5 computer languages and am very advanced at many tech things (the ones I am not as good at I am still usually Average or Medium skilled) so it makes me wonder why I have so many tech problems with Macs when they are supposed to be the "easy" OS to use...Actually, I think I have it all working now. After going back to the Plextor Website, I found out that the switch between the USB and 1394 ports only gets activated (switched over to the other) with you turn the device off first, move the switch and then turn it back on. I was sure that I had done this with the ibook, but maybe not as when I went back and did it with first the USB and then the Firewire cables, it did work. I definitely knew that I had not done this with the Windows laptop, the reason it would not have the USB work for me on it.
but back to the iBook, I was confused as it was only showing up as a DVD-ROM (which I guess is what they do until you actually open up the burning software to then be able to burn to it), and it also had the wrong Model #, which after more research, showed that it was the Internal DVD drive model version (PX-708A) compared to the actual model version (PX-708UF) which is the USB/Firewire (External) model. The firmware was really out of date as well (from June 2004 I think, v1.06) and they had v1.12 from Spet/Oct 2006 available so I went to get that (which was a hassle). They had nice easy Windows self extractor/installer packs, and then the BIN files for use for all systems (Sun OS/ Mac OSX/ Mac OS/ Linux etc as well as usable for Windows), and those needed a special Firmware Updater Application which was OS specific. Only I had the hardest time trying to get the OSX one as it would send me to a FTP site and not give me any clues as to which file(s) I needed to get and the Mac OS version was just for older 9.2 or below versions and didn't want to install under the OS Classic mode.
I ended up using my windows computer which made it easier to view with the FTP stuff as I have FireFTP in Firefox, and downloaded the files I thought I needed (to test out), and then realized my silliness, and just downloaded (as well) the Windows Auto Extractor/Installer as the Firmware is the same for all OS's, just the way to install/update it was different... So I hooked the DVD drive to my PC and updated the firmware, checked it out on here before moving it back to the ibook, where I checked that it still worked and had the new update version showing, which it did, and now I have my fully working and newly updated drive ready for the OSX installations... I had attempted to update my Jaguar system as well while online, but it had no new updates available (I guess those were all mostly Tiger updates that were just recently released).
I am now off to install my additional RAM, and after checking that it all shows up correctly, I will go ahead and do the Panther Install (and test it out and see if I like it or not).
For anyone that currently uses Panther on any mac, are there still any major problems I should know about before hand, or know about things that they have mostly fixed (like the issues with Firewire ports and External Drives that they had around the time Panther was first released for example)???
Thanks to all that helped... I now know to attempt an "eject" of any external HD (which I do have one that I will setup to use after I get Panther on the ibook) or CD/DVD drive instead of just unplugging the USB/Firewire cable. -
Hi,
As the title of the thread says. I have an older iMac with a mini display port and a newer iMac with a thunderbolt port. Would it be possible so that the older iMac is an extension of my new iMac. The reason for this is because logic x can be a abit clustered on one screen.
ThanksIf you'll be using the 2010 iMac as the display, a Mini DisplayPort to Mini DisplayPort cable.
It's not possible to use the 2011 iMac as the display through Target Display mode in that configuration.
(126322) -
Does 2 firewire audio and video interface can work together on FCP ?
hello,
My audio interface is a TC Electronic Konnekt 24D
my video interface is a Canopus ADVC 110
my hard drives are plugged in firewire too
and I use Final Cut Pro 5.0.4
So, the konnekt is recognized by FCP only when the Canopus is not plugged. And even then, the audio sometimes drop out and sometimes causes the app to crash, so that I have to trash the preferences
When I plug the Canopus, the Konnekt 24D is recognised by OS X but not FCP
I want to use the voice over tool with the konnekt 24D, so what should I do ?
Does 2 firewire audio and video interface can work together ?
If so, maybe I only have a driver problem from TC Electronic.
But if not, I have to change this interface. Let me know if only RME, MOTU, Presonus and Edirol work, as it is said on apple's webpage for hardware compatibility
thanks
eMac G4 1,25 Ghz Mac OS X (10.3.9)
eMac G4 1,25 Ghz 1 Go RAM DDR Mac OS X (10.3.9)The 1082 does show up as a possible input when I open
the VO tool.
Ok. So an audio interface can be plugged to FCP without crashing the app. Because of the Konnekt driver problem, I wasn't shure of this.
I use my Aja box for export & external monitoring.
All my audio sources run back into the Tascam and I
use the analog mixer in the 1082 to monitor different
sources.
When I view external video, the audio follows it to
keep sync.
that's exactly what I want with other I/O interfaces. I'd like to monitor video with the canopus ADVC 110, and monitor audio with the Konnekt 24D (or another interface if this one is not compatible)
I also imput dailies with a deck or a camera (DV or HDV) but that's not the point here.
I want to imput audio with the Konnekt 24D because of its audio quality. Not audio sync to video dailies. But voice over, in sync with FCP video playback (for me, tha ADVC 110) -
I have just upgraded from a Macbook to a Macbook Air. I have been using a iomega external hard drive for Time Machine, which use a Firewire. However, Macbook Air's do not have a Firewire port and i cannot find an adaptor anywhere. Can anyone help?? Thanks
There has never been a reliable firewire ---> USB adapter suitable for external high speed storage. This was a major issue when the MacBooks lost the firewire port a number of years ago (Apple subsequently brought it back).
The only high speed port on the Air is the ThunderBolt port. There are external ThunderBolt drive options out there, but they're somewhat more expensive than traditional USB/FireWire options. -
Intel iMac: 1 or 2 FireWire Ports?
The icons on the back of my Intel-based iMac clearly identify 2 FireWire ports. Only one of them, however, accepts my FireWire cable (for WD MyBook). The other port appears designed to accept a totally different cable that I cannot identify!
Are there 2 different levels of FireWire that require individual port configurations?
Message was edited by: nkhThe 24 in. 2.8 GHz iMac has two firewire ports as previously stated: one is Firewire 400, the other is Firewire 800.
You can check the specs here (click on Compare Specs/Complete Specs)...
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?nnmm=br owse&mco=7B723680&node=home/shop_mac/family/imac -
I have hp laptop dv9009us one day all the USB ports and webcam camera stopped working
I have hp laptop dv9009us one day all the USB ports and webcam camera stopped working, I had windows XP and tried all solutions posted on online forums didn’t work, I upgraded to windows 7 and still not working, please note that the USB is detected in device manger and it says working properly but he webcam is not detected at all, also when I connect any device to USB it gives it power and I even can charge my cell phone but it doesn’t detect any device. Is there any genius out there that can help me?
Also after I installed windows 7 I went o system information----software environment--- system drivers, and I found all USB drivers stopped by the way this was the case in windows XP as well
usbccgp Microsoft USB Generic Parent Driver c:\windows\system32\drivers\usbccgp.sys Kernel Driver No Manual Stopped OK Normal No No
usbcir eHome Infrared Receiver (USBCIR) c:\windows\system32\drivers\usbcir.sys Kernel Driver No Manual Stopped OK Normal No No
usbehci Microsoft USB 2.0 Enhanced Host Controller Miniport Driver c:\windows\system32\drivers\usbehci.sys Kernel Driver No Manual Stopped OK Normal No No
usbfilter AMD USB Filter Driver c:\windows\system32\drivers\usbfilter.sys Kernel Driver No Manual Stopped OK Normal No No
usbfltr Razer Copperhead Driver c:\windows\system32\drivers\copperhd.sys Kernel Driver No Manual Stopped OK Ignore No No
usbhub Microsoft USB Standard Hub Driver c:\windows\system32\drivers\usbhub.sys Kernel Driver No Manual Stopped OK Normal No No
usbohci Microsoft USB Open Host Controller Miniport Driver c:\windows\system32\drivers\usbohci.sys Kernel Driver No Manual Stopped OK Normal No No
usbprint Microsoft USB PRINTER Class c:\windows\system32\drivers\usbprint.sys Kernel Driver No Manual Stopped OK Normal No No
usbstor USB Mass Storage Driver c:\windows\system32\drivers\usbstor.sys Kernel Driver No Manual Stopped OK Normal No No
usbuhci Microsoft USB Universal Host Controller Miniport Driver c:\windows\system32\drivers\usbuhci.sys Kernel Driver No Manual Stopped OK Normal No No
uwbusb UWB Bus Control USB-Miniport Driver c:\windows\system32\drivers\usbuwbmini.sys Kernel Driver No Manual Stopped OK Normal No NoDid you ever get this resolved? I am having the same problem and have tried just about everything for my dv9000.
-
Problem with IOS 6 on iPhone 4S photos and video camera.
After the upgrade IOS 6 on iPhone 4S - no longer take photos and video camera. What to do? Reinstall ios6 again - nothing has changed. Help please.
Since iOS 6, I can't get any barcode scanners to focus on my 4s. This includes the stock scanner from Apple. Tap to focus does nothing.
-
how can I operate multi displays on my Imac 21.5 quad core 2.5 using Lion and have each display function independently?
Below are some converters/adapters to look at. If these look like they may work:
USB 2.0 to HDMI Audio Video 1080P Adapter for Windows and Macbook
Matrox DualHead2Go D2G-A2D-IF (or look here)
These should allow you to run multiple displays in extended display mode. Note that these use HDMI as an output so you would need some additional adapter to conver HDMI to whatever your displays require. Of course these suggestions are all academic if such an adapter doesn't exist.
Update:
I just reread your last post and I am confused. Is it only your TV that you are trying to run in extended display mode? I thought you wanted more than two displays. If only the TV it should just work if you are not using mirrored displays. Your Displays Arrangement tab should show both your main screen (one with the little whith menu bar) and the TV. Set the proper resolution and refresh rate for the TV using it's Displays preference window. That is all you need to basically do (ignoring overscan/underscan problems).
Note, if you are using Lion then I have heard that when using full screen mode in Lion additional screens show nothing. -
Will It Work on Leopard: iMac Late 2009 with Quad Core i7, 8GB and 4850 Mobility GPU
Hi. I'm doing an experiment if the garbled screen (unreadable but the OS and files are not being corrupted at all) I'm experiencing since I upgraded to Lion (up to Yosemite) is a software bug (specifically when it's running it's 3D drivers) or a hardware bug (possibly the GPU is failing). I would rule it as a hardware, that the iMac's GPU is failing but when I used Ubuntu 14.04 Live CD which does not use any of the 3D drivers (it doesn't use OpenGL) for its 3D acceleration, it's perfect there which is why I feel it may be a software bug- no problems with 3D acceleration.
If Leopard would work on the late 2009 iMac with i7 quad core, that'd be great.
Thank you in advance.
God bless, Rev. 21:4The only issue I have found is that the there are no additonal display resolution settings to adjust.
So the iMac is stuck with its native resolution in OS X 10.5.8 Leopard (I hate the iMac's 2550 x 1900 resolution. Everything is just too small for my 50 year old eyes.)
You can adjust the size of icons and icon text size in the Finder Prefs and View Options, you can adjust the Dock size, but that is pretty much it.
No way to adjust the size of the text in the top main menu bar or make the text in the title bar on Finder windows larger, either.
But everything else works.
I can access all of my other external drives, most of the applications, that are mostly updated to work just with OS X 10.5.8 Leopard, launch and work fine. My Wacom Intuous3 tablet seems to work fine add I can adjust the preferences and controls of all of by pens and airbrush tool.
My older IR Microsoft and Logitech mice work fine.
I can't believe how much faster OS X 10.5.8 runs on this iMac.
If I hadn't updated all of my Apple apps on OS X 10.6.8 Snow Leopard and all my updated iTunes, iPhoto and Aperture Libraries, long ago, needed more up to date web browsers (TenFourFox wasn't available back in 2011) and Mail clients, more up to date Flash and security updates, I might have just stayed using OS X 10.5 Leopard on this iMac.
It is quite a bit faster than Snow Leopard. Even that much faster considering I am running OS X 10.5.8 from my external FW800 drive. -
Will It Work on Tiger: iMac Late 2009 with Quad Core i7, 8GB and 4850 Mobility GPU
Hi. I'm doing an experiment if the garbled screen (unreadable but the OS and files are not being corrupted at all) I'm experiencing since I upgraded to Lion (up to Yosemite) is a software bug (specifically when it's running it's 3D drivers) or a hardware bug (possibly the GPU is failing). I would rule it as a hardware, that the iMac's GPU is failing but when I used Ubuntu 14.04 Live CD which does not use any of the 3D drivers (it doesn't use OpenGL) for its 3D acceleration, it's perfect there which is why I feel it may be a software bug- no problems with 3D acceleration.
If Tiger would work on the late 2009 iMac with i7 quad core, that'd be great.
Thank you in advance.
God bless, Rev. 21:4Tiger won't work.
Install OSX Restrictions -
I am about to get a 27" iMac 3.4 Ghz i7 Quad Core with Lion installed.
I want to run one or two old applications that will not run under Lion.
Is it possible to partition the iMac to run Snow Lepoard from there when I need it ?I have tried to partition my Macbook Air (running Lion) using Bootcamp but all it will let me do is install Windows (which I do nor want to do.) Otherwise it will not partition the HD.
It gives three options. 1. Create a Windows 7 install disc. 2. Download the Windows support software. 3. Install Windows 7.
For interest I ran Bootcamp on my iMac (running Snow Leopard) and that would allow me just to partition the drive
(with no need to install Windows) by checking "I have the Mac OS X installation diec... or I have the support software.." (which I don't) and then goes to the partitioning page.
If you can put me wise I wouldbe grateful.
Cheers
Roger.
Maybe you are looking for
-
Payment terms different between sales docs
Hi Gurus. Why do I have payment terms different between sales doc and billing doc for the same customer? Detail: the sd and company code vision has the same value in customer master data (xd03, vd03). Thanks in advance! Renato
-
I need to be able to give my client access to a few pages with links. These links will change often and they want to make the changes. What is the best solution if you can insert a Wordpress page into Muse?
-
Apple TV movies are slow to download
my movies are downloading extremely slow. Does anyone have information that can help?
-
Does anybody know what this is about? I've tried looking it up on google, but with no success. Thanks.
-
How can i know report_server value
hi all i installed IDS 10g but i dont know what is the report_server name how can i know it ? thanks