Imadmin purge domain command failing, was working !
Hi Folks,
iMS 5.2p1, iDA1.2p1, Solaris 8
Seem to be having problems with purging domains, that I never use to have. I use an input file to the imadmin command.
eg. imadmin domain purge -i filewhatever domain I try and purge, a failure message is returned.
domain.com: purge domain failed:
Failed: the domain (or nested domain) cannot be deleted because it contains Service AdministratorsI only have the one 'serviceadmin' user setup at install time. I've had a good look around in LDAP, but can't find out what's the prob. I do have a 'sizelimit' (ldap search return size) issue in LDAP currently, that needs tweaking, but would this cause the problem.....maybe it does. Can anyone confirm. Or is it another prob entirely. Any pointers would be great.
Cheers,
Thanks Jay, I should have said before I posted I used '-v' to imadmin and went through LDAP access/error logs. No more useful debug info. from imadmin, just the error I get back.
I went back to LDAP and went more finley through the access log. All looks fine, BIND and SRCH and err=0 codes, when looking for the domain. The 'serviceadmin' and 'NDAUser' uid's are called. The domain is found and LDAP filters search on (ObjectClass=inetDomain) and (inetDomainStatus=deleted). Right at the end there is a SRCH using a filter (ou=cn=Service Administrators*) attrs=dn . Where I get a RESULT err=11. This is my problem, err=11 is 'LDAP Admin Limit Exceeded'.
So it appears it could be related to my 'sizelimit' issue problem with LDAP. So I be tweaking that, to see if that helps. Any sugguestions ?
Similar Messages
-
Problems with the imadmin purge user command
I am using iMS 5.2 hot fix 1.05, iDA1.2sp1 and iDS 5.1
When I try to use the imadmin purge user command I get the following errors:
[email protected]: purging user
[email protected]: purge user failed
Failed connection refused.
If I don't use the -g 0 option then it reports success, but the user account is still in LDAP...
I found a reference to the imadmin user purge command not working when you have iDA 1.2patch1 and iMS 5.1 patch 1 unless you make a change to your resource.properties file but i have tried the file both way and I get the same error with the purge user command.
I can use the imadmin delete user or imadmin modify user without any problem. I am just having trouble with the imadmin purge user command.
Any ideas?This problem is documented in bug id 4671472. I have attempted the recommeded fix, but the problem persists. If anyone else has been having a similar problem and has any solution let me know. Thanks.
Peter -
MSI Command center, was working, now crashes
Hi, I've been running Command Center version 1.0.0.50, and it's been working just fine, suddenly since yesterday it's been crashing shortly after loading, also the CPU always reads as max speed(3.7ghz) and doesn't move from there, whereas before, it was reading the correct frequency, I've tried uninstalling, and reinstalling from my driver cd, and it doesn't fix the issue, I've also tried version 1.0.0.68 from the website, and it's doing the same thing.
Also, just to note, other CPU frequency monitoring programs (CPU-Z for instance) are reading the frequency correctly, so I don't think it's a hardware issue.
Additionally, my Avast A/V has suddenly decided that the "msiwmiservice.exe" file from the 1.0.0.50 version is a rootkit(I've verified that it's a false positive), but I can no longer run the 1.0.0.50 version at all without disabling Avast, because every time I install it from the disk, it immediately throws the offending file into the anti-virus chest. This doesn't happen with 1.0.0.68, as it doesn't contain the offending file, but it still crashes the same.
Also, note that Avast and Command Center had been living together just fine for a couple weeks, right up until yesterday..... weird huh?
I'd like to be able to run command center for its hardware monitoring...... can anyone help me sort this out?
My system specs are
MSI H81M-E33 motherboard - BIOS version V6.4B3
Intel I5-4590 CPUTry this one 0.69 Beta 2:
https://dl.dropboxusercontent.com/u/40094917/Command%20Center%201.0.0.69beta2.zip
before install it, deinstall the old one, then manually delete Command Center folder.
Then install the new one 0.69 Beta 2
after install and run it, when the loading error issue hapends,
go to local disk C in MSI folder, ie: C:\MSI
then locate a file named “MSILoading” and send it back. [upload it somewhere and give a link to it]
How to use forum features: https://forum-en.msi.com/index.php?topic=90789.0
Quote
Also, note that Avast and Command Center had been living together just fine for a couple weeks, right up until yesterday..... weird huh?
let us know if the "msiwmiservice.exe" service is still detected by Avast!
in latest Command Center version, if yes provide a screenshot with the issue -
When I try to open my Adobe Acrobat X Pro I get a message that it failed to send a DDE command. It was working fine until yesterday.
When I try to open my Adobe Acrobat X Pro I get a message that it failed to send a DDE command. It was working fine until yesterday.
-
Hi I installed a new hard drive in my Mac mini osx lion an when I turn it on I get a flashing file with a question mark. I tried holding command and R keys when turning it on but the recovery fails to work. I can hold the option key at start up and choose my network, then Internet recovery shows up with an arrow pointing up. When I click on the arrow Internet recovery fails and all I get is a globe with a triangle on it with an exclamation mark on it, and under that it says
apple.com/support
-6002F
Does any one know how I can fix this without a recovery disc? ThanksI just want to add to this, in case someone else searches for this error on Apple Support (google doesnt cover apple support.. how clever is that?)
I had the same error. And i had a Computer that had worked, with a SSD drive and 16GB upgrade done by the owner himself.
I tried swapping with a Mechinal Harddrive, no luck.
Kept the Mechanical drive in, and tried with some other Ram, it worked..
So for me this error and after reading the other responses can be boiled down to a Harddrive problem or Ram issue.
It was Ram for me.. -
M475 Scan to folder/email. Was working now fails
Hi,
We have an M475 set up in an office that was behaving perfectly with regards to scanning but now fails 49 times out of 50.
All staff in the office have a 'scan to folder' profile set up which scans to a 'Scans' folder in their domain home folder.
This was working 100%.
If I get someone to powercycle the printer I can get one scan out of it. After that, if you physically try to scan, you can enter your pin, it scans the document, then hangs for a very long time.
From the web interface, if I test one of the profiles it comes up with a box with a 'Cancel' button in it & sits there until I click it.
The account being used for the profiles has full rights over the 'Scans' folders.
I have tried with the domain administrator account - Still hangs.
In the domain server logs I can see the successful validation of the account being used by the printer.
I tried creating a new profile using the same credentials. It worked first time, then never again until I disabled Bonjour & WS, then it worked once.
I don't get it - Nothing's changed in the domain. It works very occasionally. It definitely gets a green light on the folder access.
UPDATE:
Hmm... While I've been writing this it's decided to work (after 'several weeks' of refusing to (why do staff moan to each other about something not working but ALL fail to let IT know?).
The immediately obvious difference is that when I test a scan profile, instead of the box just having a 'Cancel' button in it, it also has an animated 'working' graphic, and the words 'Testing [profile name]'
Does anyone have any ideas as to what the problem was (& may well be again...) please?
Many thanksHello.
I can see you are having some issues with scan to folder/email, I would like to see if I can help you on this issue.
First, let me ask you, what is the operative system of the computer that you shared the folder for scan to folder?
Now, one experiment you might want to try, is check if the computer that you shared the folder for "scan to folder" has any kind of antivirus, and if so, check your firewall settings. If you don't have any antivirus installed, check if you host operative system has any firewall installed and check the rights.
Some times a firewall has some sort of policy to reject incoming connections from ports that are not port 80., and your printer is not using that port 80, which might be the root cause.
The experiment is simple, try to disable your firewall and then reboot your printer and let them to connect again and try.
This is not the solutions, but just an experiment to get to the root cause.
Thanks.
I work at HP.
Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may select the "Kudos" button on any helpful post to give that person a quick thanks. -
while in Lightroom, i press command e to edit in cs5, however my picture won't open in cs5. It was working just fine, then just stopped.
Please do not post questions more than once. It makes it difficult for you as well as those who will try to answer. I don't have an answer for you. However:
What operating system?
What version of Lightroom?
How much RAM?
Did you install anything new?
What version of Camera Raw are using in Photoshop CS5?
If you can provide more details, it might make it easier for someone to provide you with an answer. -
Hi, I have a freecom 1TB hard drive which was working fine until it froze. I pulled it out (mistake I now know) and now it doesn't mount. It shows up in Disk Utility but won't manually mount. When I try to repair it gives message 'failed on exit'. Some people have said to try Disk Warrior, but at $100 it's quite expensive maybe fix. help!
You likely need to reformat the drive which will destroy all data and you need a backup to restore it. If no backup is present then a data retrieval service can be more expensive than DiskWarrior. There is software that can rescue the data but I can not vouch for it's effectiveness as I have always maintained backups. .
http://www.prosofteng.com/
http://www.wondershare.net/ad/data-recovery-mac.html?gclid=CLTp3Mj07rkCFevm7AodL lUAHw
http://diskdoctors.com/software/mac-data-recovery/utility.asp?gclid=CMyf_MH17rkC Fcvm7AodSE0A8A
http://www.cleverfiles.com/ -
FaceTime was working fine then stopped. Wants me to sign in but fails to activate. I rebooted my IPad but that didn't help.
Hi jrthomus,
Welcome to the Support Communities! The article below will help you troubleshoot the issue you are having with Facetime on your iPad:
iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
Your iPhone telephone number is linked to your Apple ID when you sign in to FaceTime or iMessage. This allows you to use your iPhone number with FaceTime and iMessage on other iOS devices.
This feature isn't available on iPod touch (3rd generation) and iPad (1st generation).
This feature is available with OS X Mountain Lion v10.8.2 or later.
You can sign in to your Apple ID on an iPhone by tapping Settings > FaceTimeand Settings > Messages > Send & Receive.On iOS devices, find out which addresses are enabled with FaceTime and iMessage by tapping:
Settings > Messages > Send & Receive > You can be reached by iMessage at:
Settings > FaceTime > You can be reached by FaceTime at:
iOS: Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
iPhone automatically registers your phone number for use with FaceTime and iMessage during activation.
To use FaceTime with your Apple ID, navigate to Settings > FaceTime and tap "Use your Apple ID for FaceTime."
To use iMessage with your Apple ID, navigate to Settings > Messages > Receive At and tap "Use your Apple ID for iMessage."
When you enable FaceTime or iMessage with an iPad or iPod touch, you will need to enter a valid Apple ID and password. Other users will be able to contact you on FaceTime and iMessage using this email address.
iOS: Troubleshooting FaceTime
http://support.apple.com/kb/ts3367
I hope this information helps ....
- Judy -
Yesterday the upload to web function was working fine, this is my first attempt to up load a video to you-tube. It failed yesterday as the library closed and I lost my internet connection. I reworked the video some, rendered it and when I pushed the upload to web button, nothing happens. I am connected to the internet, what is up ?
Homefree223
I have just finished two successful uploads to YouTube at the YouTube web site, both were 1080p60 video (H.264.mp4 produced in Premiere Elements 11 with a target bitrate of about 32 Mbps (megabits per second) and maximum bitrate of about 40 Mbps (megabits per second). The uploads at the YouTube web site went without problems and the quality of the video displayed on YouTube was good. The point of all this was to demonstrate that at this time YouTube was not experiencing problems with a 1080p60 upload at its web site and that the quality of the finished upload was good. Depending on file size requirement, bitrate rates higher than the above can be looked at.
But let us recap to make sure that we have not mis-communicated on any of the details. Please correct me if any of my assumptions were incorrect:
1. You have a 1080p60 Premiere Elements 11 Windows Timeline (Expert view) and you export that to file and then upload that file at the YouTube web site. We have not gone into the specifics of the properties of the Premiere Elements 11 generated file being uploaded, but probably are:
Publish+Share
Computer
AVCHD
MP4- H.264 1920 x 1080p30 (p30 converted to p60 in the settings under Advanced Button/Video Tab...bitrate used Target 32 Mbps and Maximum 40 Mbps)
or
2, Instead, you have been trying to upload your 1080p60 Timeline direct to YouTube from within Premiere Elements 11, via Publish+Share/Online/YouTube where you might be setting Presets = "High Definition Video for YouTube - 1920 x 1080"? You realize that the frame rate for the preset in this case is 30 frames per second, not 60.
If "2" is the focus of the problem, then try approach "1" to determine if that works for you. The disadvantage of the direct upload from within Premiere Elements 11 is that there are no adjustments available for the preset used. It is, what it is.
2. Also, what did you mean by:
"It failed yesterday as the library closed and I lost my internet connection."
Please review the above. I am heading to my Premiere Elements 11 Windows to try approach "2" which I have not yet.
Thanks.
ATR -
Hi! I brought an iPhone 4 off my friend at work. The day I brought it, it was working fine but now I can't seem to send any messages or make phone calls. The network is showing up fine but each time I try to make a call it says "call failed" I can't seem to send any messages either? I can use the Internet fine and everything else on the phone. Can anyone help?
Hi chelsinator,
You can reset the phone and it won't cause any problems or cause you to lose any data - Hold down the Home and Power buttons at the same time and continue to hold them down until the Silver Apple appears.
The other thing you should do is to reset your network settings: Settings>General>Reset>Reset Network Settings. You will have to set up your Wifi again, but that oftentimes clears things up.
Cheers,
GB -
My ipad2 was working fine last night, but this morning when I woke it up... it no longer was connected to my network. While it can detect networks, it cannot connect to any (have tried at home and at work). I have tried: resetting router, resetting ipad, forgetting network, renewing lease on network, ensuring airplane mode is off, resetting network settings, turning wifi on/off. None of the typical solutions I can find online seem to work. HELP!
You've gone through all of the basics. You might look at this document regarding potential issues with wi-fi environments.
http://support.apple.com/kb/HT4199
If none of that works, and if a device restore doesn't work, it's time for a trip to the Genius Bar. -
How the PURGE INDEX command works
Hi all,<br><br>
PURGE INDEX command purges the specified index from the recyclebin.<br>
My question is: I noticed that the dropped index doesn't appear in the recyclebin, so from where it could be purged?<br><br>
SQL> CREATE INDEX Z_IND ON Z (Z);
Index created.
SQL> DROP INDEX Z_IND ;
Index dropped.
SQL> SELECT OBJECT_NAME , ORIGINAL_NAME FROM USER_RECYCLEBIN ;
OBJECT_NAME ORIGINAL_NAME
BIN$TNgWa0sgR8qFY7JXGVT3yQ==$0 T <<-- the dropped index doesn't appear here
SQL>CREATE INDEX Z_IND ON Z (Z);
Index created.
SQL> PURGE INDEX Z_IND ;
PURGE INDEX Z_IND
ERROR at line 1:
ORA-38307: object not in RECYCLE BIN
SQL> DROP INDEX Z_IND PURGE ;
DROP INDEX Z_IND PURGE
ERROR at line 1:
ORA-00933: SQL command not properly ended
SQL> DROP INDEX Z_IND;
Index dropped.I found out that the index doesn't go to the recyclebin when it is dropped. It goes there, when its underlying table is dropped.
SQL> CREATE TABLE Z ( Z NUMBER );
Table created.
SQL> CREATE INDEX Z_IND ON Z(Z);
Index created.
SQL> DROP TABLE Z ;
Table dropped.
SQL> SELECT ORIGINAL_NAME FROM RECYCLEBIN ;
ORIGINAL_NAME
Z
Z_IND -
My mail keeps coming up with "connection to server available". Was working fine then suddenly stopped. I performed the ISO 6.0.1 update afterwards hoping it wild fix it but it didn't. Have followed all the instructions on other forums ie turning phone off, deleting account and reactivating, even logged out of hotmail at home . Nothing has worked. Please help, I need my emails for work.
iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
Cheers, Tom -
Hi folks,
The Fax_Printer fails to work after running "pacman -Syu".
On;
File --> Print --> Fax_Printer --> Print
No response. The dialer does not popup for typing phone number
On browser
localhost:631/printers
Fax_Printer
Warning:
"recoverable: Network host 'locahost' is busy; wiill retry in 25 seconds...."
However no further response popup.
$ cat /etc/cups/cupsd.conf
DefaultEncryption IfRequested
LogLevel info
SystemGroup sys root
# Only listen for connections from the local machine.
Listen localhost:631
# Show shared printers on the local network.
Browsing On
BrowseOrder allow,deny
BrowseAllow all
DefaultAuthType Basic
<Location />
Allow localhost
# Restrict access to the server...
Order allow,deny
</Location>
<Location /admin>
Allow localhost
# Restrict access to the admin pages...
Order allow,deny
</Location>
<Location /admin/conf>
AuthType Basic
Require user @SYSTEM
Allow localhost
# Restrict access to the configuration files...
Order allow,deny
</Location>
<Policy default>
<Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscriptio
Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume
Job CUPS-Move-Job>
Require user @OWNER @SYSTEM
Order deny,allow
</Limit>
<Limit Pause-Printer Resume-Printer Set-Printer-Attributes Enable-Printer Disable-Printer Pause-Printer-After-Curre
t-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startu
-Printer Promote-Job Schedule-Job-After CUPS-Add-Printer CUPS-Delete-Printer CUPS-Add-Class CUPS-Delete-Class CUPS-Ac
ept-Jobs CUPS-Reject-Jobs CUPS-Set-Default>
AuthType Basic
Require user @SYSTEM
Order deny,allow
</Limit>
<Limit CUPS-Authenticate-Job>
Require user @OWNER @SYSTEM
Order deny,allow
</Limit>
<Limit All>
Order deny,allow
</Limit>
</Policy>
$ cat /etc/hosts
# /etc/hosts: static lookup table for host names
#<ip-address> <hostname.domain.org> <hostname>
127.0.0.1 localhost.localdomain localhost arch.satimis.com
192.168.0.52 arch.satimis.com
# End of file
The modem is on.
$ sudo /etc/rc.d/cups restart
:: Stopping CUPS Daemon [DONE]
:: Starting CUPS Daemon [DONE]
Please advise where I have to check? TIA
However both HP_Printer and PDF_Printer are working w/o problem.
Edit:
Performed further test as follows;
$ lsmod|grep lp
lp 11972 0
parport 38156 3 parport_pc,ppdev,lp
$ dmesg|grep lp
On node 0 totalpages: 261983
Calibrating delay using timer specific routine.. 3620.49 BogoMIPS (lpj=6031192)
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
lp: driver loaded but no devices found
lp0: using parport0 (interrupt-driven).
lp: driver loaded but no devices found
$ ls -l /dev/lp0
crw-rw---- 1 root lp 6, 0 2008-04-16 21:43 /dev/lp0
$ sudo pacman -Syu
Password:
:: Synchronizing package databases...
core 24.5K 33.5K/s 00:00:01 [#####################] 100%
extra is up to date
community 331.3K 198.1K/s 00:00:02 [#####################] 100%
archlinuxfr is up to date
:: Starting full system upgrade...
resolving dependencies...
looking for inter-conflicts...
Targets: rsync-3.0.2-1 abs-2.0-3
Total Download Size: 0.27 MB
Proceed with installation? [Y/n] Y
:: Retrieving packages from core...
abs-2.0-3-x86_64 7.4K 27.8K/s 00:00:00 [#####################] 100%
:: Retrieving packages from extra...
rsync-3.0.2-1-x86_64 266.2K 120.3K/s 00:00:02 [#####################] 100%
checking package integrity...
(2/2) checking for file conflicts [#####################] 100%
(1/2) installing rsync [#####################] 100%
==> ABS now uses rsync, instead of cvsup, to synchronize your tree.
==> Please note the new configuration in /etc/abs.conf
warning: /etc/abs/supfile.unstable saved as /etc/abs/supfile.unstable.pacsave
warning: /etc/abs/supfile.testing saved as /etc/abs/supfile.testing.pacsave
warning: /etc/abs/supfile.extra saved as /etc/abs/supfile.extra.pacsave
warning: /etc/abs/supfile.core saved as /etc/abs/supfile.core.pacsave
warning: /etc/abs/supfile.community saved as /etc/abs/supfile.community.pacsave
warning: /etc/abs/abs.conf saved as /etc/abs/abs.conf.pacsave
(2/2) upgrading abs [#####################] 100%
Reboot Archlinux. No warning in connection with udev was found on text scrolling. Problem remains
I found "FS#9867 - /dev/lp0 not created by udev"
http://bugs.archlinux.org/task/9867
The case is similar to mine. Problem happens after running update/upgrade. Previously the Fax_Printer worked w/o problem.
Remark: I have WindowsXP running on this box (on another HD). Sending and receiving faxes are w/o problem.
I think I have to downgrade "udev" if w/o a solution. Please advise how to do it? TIA
B.R.
satimis
Last edited by satimis (2008-04-16 14:58:13)Please provide the following relevant information so someone can help including:
Printer Model -
Detailed Problem Description -
Operating System of computer (including service pack revision) - Done
Connection Method - USB, Hardwired LAN, Wireless? -
Make and model of router and modem? -
Error messages - on printer screen and/or computer, any blinking light patterns?
If wireless, when the problem occurs, what is status of Blue Wireless light on printer, on, off or blinking? -
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!
Maybe you are looking for
-
Basically, I've set up my home sharing between my macbook air, and our mac mini at home. The home sharing option shows up on both computars, and the music is visable and available to listen to when I bring it up on home sharing from the mac mini, but
-
Chinese char. in PDF file
Hi, Chinese char. in PDF no problem to printer, but when spool to file, chinese char. is "###" What to be set in order to solve this issue. Thank you. Best Regards Shese
-
How can I insert a Pages, Doc, or PDF file into a Keynote presentation?
I need to insert a document (.pages, .doc, or .pdf anyone) into a Keynote for a portfolio that I must present. How can I do this? It doesn't give me that option under hyperlink in inspector.
-
Breakdown analysis report MCI7
Dear Experts, I created a break down notification for an equipment installed under a functional location and completed the notification after entering the breakdown hours with breakdown indicator checked. Now if i run the MCI7 report with the functi
-
Hello We have a unique use case. Say we have two roles A and B in a single workflow request. We want to create a workflow in CUP, that will auto provision A and not auto provision B (just capture the approval). Is this possible in CUP workflow? Thank