Impact on BI system when upgrading form windows NT to Windows 7 ?

HI all ,
very soon , we are upgrading our OS from windows NT to Windows 7 .
what are the precautions we need to take , ?
regards ,
Santhosh
Edited by: santhosh on Sep 9, 2010 12:09 PM

After Upgrade you prepare some test scenarios and execute them in Dev .. below are few checks that you can perform
- Run Process chain for test loads
-Create Infoarea / Info catalog / IO / DSO / Cube / DS flat file / Transformations / MP / Infoset / Write Opt. DSO .. entire flow and load to make sure everything is OK
-Also check the existing flows if they are any Inactive ?
-Execute queries
-Prepare test case for all day to day activities
You can search for check list docs/notes in https://websmp108.sap-ag.de/upgrade
Edited by: Srinivas on Sep 9, 2010 9:51 AM

Similar Messages

Any impact on Discoverer user when upgrade o oracle 8 to 10g

Does it has any impact on Discoverer user when database upgrade from 8 to 10g?

No, there is no impact on your users.
Best wishes
Michael

Installing new HDD after Windows XP to Windows 7 upgrade on my T400

A few weeks ago I did a clean install to upgrade my T400 laptop from Windows XP to Windows 7 Professional, using the upgrade version of Windows 7 (vs. the complete new installation version - saved about $100.00).
Now I want to upgrade my HDD from 250GB to 500GB. I purchased the HDD from Lenovo, expecting the drive to come with some guidance for the upgrade other than how to physically replace the drive. Unfortunately, no such help found.
I have researched this and I think I have a few options. I could 1) clone my current hard drive or 2) do a clean reinstall on the new drive.
While looking over Microsoft's knowledge base I came a cross an article that said that I couldn't use the Windows 7 upgrade disk on a new hard drive. The article said I would first have to recover the original Windows XP OS onto my laptop, and then use the upgrade disk. Is that right? Do I really have to start over (upgrading to Windows 7 was a bear)?
If I clone my hard drive (I have the necessary hardware & software) will the upgraded Windows 7 be operable on the new hard drive?
I'd appreciate any help or suggestions.

You should be fine with cloning the drive. Microsoft normally limits the "upgrade" to only installing over an already existing Windows or a drive with Windows on it. So yes, it is not going to install on a bare drive for you.
As long as the clone aligns the partition properly, if necessary, then the cloned drive should operate fine. I cloned my initial HDD when upgrading to an SSD. Windows might require you to re-verify the machine because of the hardware change. However, changing only one component is not supposed to trigger the verification process. Once you know that it is working properly, you Windows license probably requires you to delete it from the old drive.
When asking for help, post your question in the forum. Remember to include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help others with the same question in the future.
My TPs: Twist 2HU: i5-3317U Win 8 Pro, 4GB RAM 250GB Samsung 840 | T420 4177CTO: i5-2520M, HD+, Win 7 Pro x64, 8GB RAM, Optimus, 160GB Intel 320 SSD, Intel 6300 WiFi, BT 3.0 | T400 2764CTO: P8700, WXGA, Win 7 Ult x64, AMD 3470, 8GB RAM, 64GB Samsung SSD, BT, Intel 5300 WiFi | A20m 14.1" PIII 500 (retired). Monitors: 2x Dell U2211h IPS 100% sRGB calibrated w/ Spyder3.

Error message when displaying a report in a windows form

Hi,
use Cr 2008.SP3 Fixpack 3.5,
Visual Studio 2008 prof. editon version 9.0.30729.1 SP,
:NET Framework 3.5 sp1
vb.net 2008
when displaying a report in a Windows form sometimes the following error message appears
System.NullReferenceException: Object reference not set to an instance of an object
   bei CrystalDecisions.Windows.Forms.PageControl.OnMouseMove(MouseEventArgs e)
   bei System.Windows.Forms.Control.WmMouseMove(Message& m)
   bei System.Windows.Forms.Control.WndProc(Message& m)
   bei System.Windows.Forms.ScrollableControl.WndProc(Message& m)
   bei System.Windows.Forms.ContainerControl.WndProc(Message& m)
   bei System.Windows.Forms.UserControl.WndProc(Message& m)
   bei CrystalDecisions.Windows.Forms.PageControl.WndProc(Message& m)
   bei System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
   bei System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
   bei System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
The rest of the error message is in german:
************** JIT-Debuggen **************
Um das JIT-Debuggen (Just-In-Time) zu aktivieren, muss in der
Konfigurationsdatei der Anwendung oder des Computers
(machine.config) der jitDebugging-Wert im Abschnitt system.windows.forms festgelegt werden.
Die Anwendung muss mit aktiviertem Debuggen kompiliert werden.
Zum Beispiel:
<configuration>
    <system.windows.forms jitDebugging="true" />
</configuration>
Wenn das JIT-Debuggen aktiviert ist, werden alle nicht behandelten
Ausnahmen an den JIT-Debugger gesendet, der auf dem
Computer registriert ist, und nicht in diesem Dialogfeld behandelt.
Thank you
Otto

Can you define "sometimes" a bit more?
Is it after a number of runs of a report?
Is it on a particular report?
Is it after you do certain operations on the report (paging, zooming, dill down, print, etc., etc.)?
Can you duplicate the issue if you isolate the report to a new test app?
Did you happen to notice if the issue existed prior to FP 3.5?
Is this on your dev computer or a client computer?
OS?
Ludek
Follow us on Twitter http://twitter.com/SAPCRNetSup
Got Enhancement ideas? Try the [SAP Idea Place|https://ideas.sap.com/community/products_and_solutions/crystalreports]

Crypto failure when upgrading Windows 8.1 Pro install to Windows 10 Tech Preview 10041

Has anybody experienced the following error when trying to upgrade a Windows 8.1 Pro install to Windows 10 Tech Preview 10041
crypto_self_test_failed
The system reboots twice both times with the same error and then reverts back to Windows 8.1 Pro. This occurs during the upgrade process. Windows 10 never installs.
Thoughts? Suggestions?
Thanks
Eric Sten

Hi Eric,
It seems to be the upgrade self-test fails.
For testing Windows 10, you may consider take use of Hyper-V and install a VM of Windows 10:
Step-By-Step: Creating and Running A Windows 10 VM on Windows 8.1
Or try a dual boot:
How to Dual Boot Between Windows 7 (or Windows 8.1) and Windows 10 Technical
Preview (VHDX)
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

HP ProBook 440 G2, Finger print reader not working when I upgraded form Win 7 Pro to Win 8.1 Pro

My HP ProBook 440 G2, Finger print reader not working when I upgraded form Win 7 Pro to Win 8.1 Pro.
In device manager showing that biometric reader is working properly. But actually the finger printer reader is not reading or senseing. It seems like "dummy" part. Please help me to correctly configure step by step for this issue.
thankyou
Hillet
This question was solved.
View Solution.

Have you installed the Validity Sensor Fingerprint driver software for Windows 8.1?
http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=6943811&swItemId=ob_134806_1&swEnvOid=415...
See page 64 in the following Windows 8.1 user manual for Validity Fingerprint setup information
http://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=6943810&docId=emr_na-c04371762&docLocale...
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Windows Installer error when upgrading to Itunes 8.01

I receive the following error when trying to install Itunes 8.01 on my Windows XP Service Pack 3 system:
"There is a problem with the Windows Installer Package - A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor"
The upgrade fails and reverts back to the previous version of Itunes.
I tried re-installing windows installer and it is current. All other programs install without issues but Itunes does not install.

I tried the repair option on Itunes - ran it successfully, turned off Norton AV auto protect temporarily then immediately tried running the setup again on Version 8.01 and get the same error.
I have not yet uninstalled version 7 of Itunes on my system followed by running the Windows Installer Cleanup utility to completely remove Itunes from the system.
This issue to date has not been resolved yet but need to try the cleanup option.

What do I do with F-Secure Freedome when upgrading to Windows 10?

QuestionWhat do I do with F-Secure Freedome when upgrading to Windows 10?
AnswerWhen upgrading your operating system from Windows 7, 8, or 8.1 to Windows 10, you can choose to:
Keep your programs and data through the Windows 10 upgrade (Recommended)
If you choose to upgrade to Windows 10 whilst keeping your programs and data, the Freedome application does not get removed and continues to work normally after the upgrade.
Make a fresh (clean) Windows 10 installation
If you choose to make a fresh (clean) Windows 10 installation, you will need to reinstall Freedome after the Windows 10 upgrade. Do note that this method of upgrade requires you to type in a new subscription code as every installation of Freedome uses one of your available subscriptions.
Note: If you have had an expired trial subscription of Freedome on your computer before the Windows upgrade, it will remain expired after Windows has been upgraded. This applies to both the Windows upgrade methods mentioned above.

Thanks but the tool only works if you have one working windows installation and it's designed for mult-boot systems. I don't have a multi-boot system and when the Windows 10 upgrade fails there is no active working Windows install to turn to. The partition gets corrupted and has a "RAW" status until you run chkdsk with gets it back to "NTFS" status but it won't boot. My only two options at this point is to restore back to an image backup or install Windows 7 all over again. I'm just going to give up on this HP laptop, to me it's just not compatible with running this upgrade, so unless someone else has any other ideas this attempt to upgrade is over. Thanks again

Lost sound when upgraded to Windows

I lost sound when I upgraded my Gateway Solo250 from Windows 98 to Windows XP Home. On Device manager, the systems reports that my sound controls are working but the Multimedia Audio Controller is not installed (Problem 28). I have downloaded drivers from Gateway and from Creative Labs Sound Blaster Li've but can not install them. I get the error message that no sound card is being detected. What happened? How do I fix this without messing up anything else, since the computer is operating smoothly, except without sound. Thanks for your help!

I have the exact same problem. I got numbers off of the creative chip on the motherboard, if that helps to get a solution. Gateway lists that XP is not supported on solo250. Creative is the only source that can solve this, since all of these companies laid off all of the developers. Did you find any help at all? I would hate to go back to win98...

Would PKI Infrastructure be affected when upgrading schema from Windows 2003

Hi
I am planning my schema upgrade from either Windows 2003 to Windows 2008 or from Windows 2003 to Windows 2012.
I would like to know if in any of these scenarios would my PKI Infrastructure be affected?
Thanks.
Regards
Andre Thompson
Regards Andre Thompson

Hi,
If currently you are using a Windows Server 2003 as a DC, and you are going to add a new Windows Server 2008 or 2012 to your environment, you will need to demote it first - if CA is installed on that 2003 DC, you will need to uninstall it for demotion.
http://social.technet.microsoft.com/Forums/windowsserver/en-US/94fa88e6-b299-436c-bca1-e88b45ea86b8/impacts-when-upgrading-only-ca-servers-to-2008-r2-in-a-2003-domain?forum=winserversecurity
If you have any feedback on our support, please send to [email protected]

Just upgraded to latest iTunes for Windows. Rebooted the PC as required. When I bring up iTunes I get a pop message saying "An unknown error occured (-42110)". What does that mean?

Just upgraded to latest iTunes for Windows. Rebooted the PC as required after the update. When I start iTunes I get a popup message saying "An unknown error occured (-42110)."
What does it mean?
How do I fix it?
Thanks!

Removing the SC Info folder as per the "Error 3001," "-42110," or "5103" section in the Specific Conditions and Alert Messages: (Mac OS X / Windows) section of the following document seems to help most folks reporting the iTunes launch 42110s:
iTunes: Advanced iTunes Store troubleshooting

On Windows 7 Enterprise OS, Firefox failed to start when upgrading to any higher versions after 6.0.2

Hi
Please can you help me with this?
Currently I am running Firefox version 6.0.2 on my Windows 7 Enterprise OS Desktop.
When I try to update Firefox, installations completes successfully. However when trying to launch Firefox, browser window is not opened. It was showing a 'Firefox failed to start' error message for versions before 11. For the latest version i.e 11, no error messages are displayed. When trying to launch application, no browser window is opened, but I can see Firefox process running in Task Manager. I tried to do a clean install by removing all add-ins and also deleting Firefox folder under program files. It did not solve the problem.
Thanks
Chandra

Ok, well let's try going straight to what the problem probably is, a corrupted profile.
Can you please read [https://support.mozilla.org/en-US/kb/Managing-profiles https://support.mozilla.org/en-US/kb/Managing-profiles], and create a new testing profile? Start Firefox 6 up using the new profile, then close it. After you've done that, upgrade to Firefox 11, and try starting, again using the new profile. If everything works, then you just had a corrupted profile, and you can read [[Recovering important data from an old profile|Recovering important data from an old profile]], which explains how to transfer your data from your old one to your new profile.
Let me know if this helps!

Adobe Creative Suite 5 / Upgrade System Windows Vista to Windows 7

Dear customer service,
I am a customer of Adobe as I bought two years ago the Adobe Creative Suite 5.
My system is still Windows Vista. Now I wanna buy the Microsoft Home Office 2013 and now I have to upgrade from
Windows Vista to Windows 7.
My question is if there will be any problem with the Adobe Creative Suite 5? Or can I only put in the upgrade CD,
leave the Creative Suite on my pc and have nothing else to do than just installing?
Thank you for your reply.
With best regards,
Nicole

Correct. You only need to run the CS5 installer and have to provide the pertinent serial numbers in the process. Just make sure you run Help --> Deactivate bevor nuking your Vista install and reformatting your drive. If there are issues during the install, ask in the Download, Install & Setup forum.
Mylenium

My computer is in Windows 8.1 system, when I play on exe on the CreativeCloudSet-Up.exe, appears thar this version is to Windows 7.0, what I have to do?

My computer is in Windows 8.1 system, when I play on exe on the CreativeCloudSet-Up.exe, appears thar this version is to Windows 7.0, what I have to do?

uninstall anything cc that's installed, clean (Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6).
download the cc desktop app and install it, Download Adobe Creative Cloud apps | Free Adobe CC trial

Just upgraded my iPad to IOS5 and when the download was completed, a window said that there was an error and it could not restore. Now I have a black screen with the Apple logo and the circle lines. None of the buttons respond. Help, please!!

Just upgraded my iPad to IOS5 and when the download was completed, a window said that there was an error and it could not restore. Now I have a black screen with the Apple logo and the circle lines. None of the buttons respond. Help, please!!

Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. Maybe this will let the iPad reboot and then you may need to restore again but see if this helps to start the iPad first.

Impact on BI system when upgrading form windows NT to Windows 7 ?

Similar Messages

Maybe you are looking for