Installation not completed - error at step# 10

I was not able to get past step #10 to establish a passcode because it came up with an "error in configuration" and would not let me proceed. Yet, even though I just had to exit without completing installation, now all of my family is able to connect wirelessly with our laptops and all seems fine, but did I miss any important steps after #10 that will cause problems in use later? This router is installed in a vacation rental a long distance from our home so I want to make sure it is correct before we leave.
Product #WRT54G version#8
Cayman

hi...
actually sometimes it does happen.....
but to make sure that the router has properly connected get in to the interface go to the status and check if yOu can get an IPaddress and DNS from there...

Similar Messages

I've been trying to purchase Texas holdem chips, but it comes up as. Purchase not completed error! Plz help me

Need to purchase, but comes up as purchase not completed error. Help me plz!!

If you are also getting a message to contact iTunes Support then you can do so via this link and ask them why the message is appearing (these are user-to-user forums) : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

Could not Complete Error with swatches

Hi, I am running an action that Resets Swatches in PS6 and allows me to paint in Black or White. However everytime it gets to the Reset Swatches the action gived me a "could not complete" error. If I press OK it does reset the swatches.
Likewise I have an axtion that Flips swatches, any action that has a reset swatches part fails.
If I try to manually switch swatches I get the same error
Any ideas what the problem could be please?

Hi,
What operating system are you using?
Did you record the action in photoshop cs6 or is the action from an earlier version of photoshop?
Have you applied the latest updates for photoshop cs6 by going to Help>Updates from within photoshop cs6?
Have you tried resetting the photoshop cs6 preferences?
http://forums.adobe.com/thread/375776?tstart=0

Installation not complete

I am trying to install Solaris 10 on AMD XP processor.
My problem is the installation is not complete. Means, after booting from CD 1 everthing works well, installation program reboots and after rebooting prompts for CD 2. First time it was thorough with CD 2 and in CD 3 after finishing 36% the system hangs. I had to switch of the machine. After rebooting, it prompts for CD 3 again, I say SKIP., then it goes for CD 4 but again it hangs after 55 % of CD 4.
I just don't understand why this happens. I had allocated about 30 GB for solaris partition. I have 1GB RAM.
Kiran

Thanks for letting me know Hkitty .
I don't believe it would be a issue with the PDF, since you can't print from Word either.
You can always restore your computer back to a earlier time when everything was working properly.
System Restore for Windows 7.
Here are a couple more things you can check first, if you like.
Print a configuration page to get the printer's IPv4 address.
Printing a Configuration Report.
If you have a valid IP address for the printer then try and access the Embedded Web Server for the printer.
Type the IP address into your web browser's address bar. (Internet Explorer)
If it loads the printer's network page then the printer is on the network.
Power cycle the router, computer and printer.
Check the port assigned to the printer on the computer.
Go to Start, Devices and Printers, right click the printer and left click Printer Properties, select the Ports tab.
It should be checked on TCP/IP.
Then click on Configure Port to view the IP address.
If the IP address doesn't match the printer's IPv4, then create a new port with the new IPv4 address.
Close the configure port window.
Click Add Port, select Standard TCP/IP Port, then select New Port and follow the wizard.
Type in the proper IP address for the printer.
Make sure the printer is online.
Try printing again.
Please let me know the results.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Checkpoint not complete error

hi,
i am having oracle 11gR1 in windows 2003 server. i got the below mentioned error very frequently. I was having 4 redolog groups with 2 member each. After surfing in internet and discussion i have added 4 new groups of redo log with 2 member each. After adding i dint get the below error till now.
Thread 1 cannot allocate new log, sequence 11813
Checkpoint not complete
Current log# 1 seq# 11812 mem# 0: D:\APP\ADMINISTRATOR\ORADATA\ORCL\REDO01.LOG
Thread 1 advanced to log sequence 11813
Current log# 2 seq# 11813 mem# 0: D:\APP\ADMINISTRATOR\ORADATA\ORCL\REDO02.LOG
Thread 1 cannot allocate new log, sequence 11814
Is that the perfect solution??????????????????????????????
i am also a bit confused on why this error is occuring can any one explain me?????
Is there any other solution for this error?????
Thanks in advance

Hi,
You need to find a proper balance between the number of redo log groups, the redo size and eventually the speed of the storage used to store the redo log files.
By adding more redo log groups, you actually "delay" the moment when the redo log group will need to be re-used (goes round-robin).
At the same time, increasing the size of your redo logs will also increase the "loop back" time, but too large redo logs can / will increase recovery in case of instance crash.
Increasing the number of ARCn processes may also help.
Is that the perfect solution??????????????????????????????If you find one, let it be known!!
But you can of course find a proper balance. Some tests based on knowledge you can gain from documentation is a "perfect" start.
i am also a bit confused on why this error is occuring can any one explain me?????SB's post was more than clear enough
HTH,
Thierry

Installation Of ECC error in step create temp licence:

We are in process of installation of ECC 6.0 on our server with OS: RHEL5 and DB:MaxDB
We are getting an error in step Create Temp Licence. The error reads as follow.
INFO 2008-02-21 04:56:12
Execute step createTempLicense of component |NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|10|0|NW_Postload|ind|ind|ind|ind|10|0|NW_Postload_ADA|ind|ind|ind|ind|1|0.
INFO 2008-02-21 04:56:12
Working directory changed to /tmp/sapinst_exe.8005.1203531194.
ERROR 2008-02-21 04:56:12
FRY-00001 Cannot load library iamodapp.so: iamodapp.so: cannot open shared object file: No such file or directory.
INFO 2008-02-21 04:56:12
Working directory changed to /sapinstd11n.
ERROR 2008-02-21 04:56:12
MUT-03025 Caught ESAPinstException in Modulecall: ESAPinstException: error text undefined.
ERROR 2008-02-21 04:56:12
FCO-00011 The step createTempLicense with step key |NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|10|0|NW_Postload|ind|ind|ind|ind|10|0|NW_Postload_ADA|ind|ind|ind|ind|1|0|createTempLicense was executed with status ERROR .
Please suggest.

Hi,
the installation process aborts in "Create sap license" with error message "library iamodora missing", some libraries needed are missing to work around this, either after it aborts or event before staritng the installation unpack the libraries into the installation directory using:
SAPCAR -xvf /<sapinst-CD>/SAPINST/UNIX/LINUX_32/SAPPROD.SAR
1. Copy the installation media dvd to a directory on a files system
2. change directories into the sub-directory which contains the executable (sapinst)
3. run the command sapinst -extract
4. It will unpack the missing libraries into the same directory where you executed the command..
5. copied these libraries to lib folder
6. Stop and restart the installation
regards,
kaushal

Checkpoint not complete error in alert log

version : 10.2.0.5 , 11.2.0.2
This is what I found about "Checkpoint not complete" from google
"+This message indicates that Oracle wants to reuse a redo log file, but the current checkpoint position is still in that log. In this case, Oracle must+
+wait until the checkpoint position passes that log. Because the incremental checkpoint target never lags the current log tail by more than 90%+
+of the smallest log file size, this situation may be encountered if DBWR writes too slowly, or if a log switch happens before the log is completely full,+
+or if log file sizes are too small.+ "
Question1.
What do they mean by Oracle reusing a redo log file ? When one ORL is full , oracle will switch to the next one ; it won't reuse it. Right ?
Question2.
"the current checkpoint position is still in that log" . What is checkpoint position ?
Question3. How often does a checkpoint occur ? (frequency as per time)

Question1.
What do they mean by Oracle reusing a redo log file ? When one ORL is full , oracle will switch to the next one ; it won't reuse it. Right ?You have some groups of redo log, each redo log has members with same information. Redo log run in a circular way, when a group is full, changes to the next group of redo log and when the last group is written continue overwritten the first group.
http://docs.oracle.com/cd/B28359_01/server.111/b28310/onlineredo001.htm
Question2.
"the current checkpoint position is still in that log" . What is checkpoint position ?copy and paste from:
http://docs.oracle.com/cd/E14072_01/server.112/e10713/startup.htm#BABGDACG
"A data structure that indicates the checkpoint position, which is the SCN in the redo stream where instance recovery must begin"
Question3. How often does a checkpoint occur ? (frequency as per time)Checkpoints occur in diferents situations, not per time, please check:
http://docs.oracle.com/cd/E11882_01/server.112/e16508/startup.htm#CNCPT89045

Installation not completed

Around 6 months ago Verizon came to my apartment building and cut holes in the walls, wired and set up jacks, (over 100 units) I recently received word our area is good for the installation, so I called and set up an appointment, the tech arrived and about 2 hours into the install tells me he cannot finish the job because my apartment is not grounded, he then called Verizon and explained the problem, a few minutes later I received a call from Verizon stating this has to be taken care of by the landlord, when I notified the landlord he told me no way is he going to rewire the building.
Verizon I am a little upset and I think you dropped the ball on this, if before you spent the time and money cutting holes installing jacks you should have mentioned there was specifications that needed to be met first, now you do this work and expect the landlord to meet your specifications to finish the job, that doesn't seem right. You have lost the business, lost time and money, the technician lost the install, I lost a days work. And I still have no fios.
This should not have happened, There must be something that can be done to resolve this. This will be a problem in the future and needs to be addressed.
Thank you for your time.
Dennis Harris
{edited for privacy}

Recently several states have changed the electrical codes with some very strict requirements regarding grounding. Especially NY. And even though Verizon installed all of the phone jacks and such, they dont do electrical, so they may not have even known at the time. If during the ONT installation, there is not the new required ground available, they are not allowed to continue until the building is brought up to code. Now quite honestly, this is a complete guess as we dont know what happened in your specific case but as this has been a fairly common issue since the grounding requirements change in some states, its a fair guess.
====================================================================================
Error exists between keyboard and chair.

Behavior of silent installer not completely specified

On page 3 of the "Adobe AIR 1.5 Runtime Redistribution Instructions" under "Silent installation" states in part:
The AIR application installer installs the correct version of Adobe AIR on the target computer, as required by the AIR application to be installed. For example, if the AIR application to be installed requires the AIR 1.1 runtime, and the end users computer has only AIR 1.0 installed (or no version of AIR installed), the installation process installs the AIR 1.1 runtime along with the AIR application.
and then:
To install or update the runtime only, use the -silent option without specifying a path or any other options.
However, the instruction do not specify what happens in the following case:
+ The -silent option is used to update the runtime only.
+ The user already has a newer version of AIR on his/her computer than what is about to be installed.
What happens in this case? Does the installer:
A) Do nothing and exit successfully?
B) Downgrade the user's installed AIR version?
C) Exit with an error code, message, or dialog?
D) Something else??

When a newer version of the runtime is already installed, the installer (running in silent mode) does nothing and exits.
Note that to install Adobe AIR silently, you must contact Adobe and request an Adobe AIR runtime redistribution license. It sounds like you have already done this, Paul, but I just want others to know. Here are details:
http://www.adobe.com/products/air/runtime_distribution1.html

WT6 PL10 - Synch not completing - Error during Order Synch

Hello everyone,
I have upgraded an environment to WT6 PL10 and the Synch never completes itself and I get the following error during an order synch:
-5002:Internal error (-5002) occurred
   at NetPoint.SynchSBO.SBOObjects.SBODocument.NP_2_SBO(Documents& document, NPOrder order)
   at NetPoint.SynchSBO.SBOObjects.SBOOrder.NetPointToSBO(NPQueueObject qData)
   at NetPoint.SynchSBO.SynchObjectBase.Synch()
Unfortunately the synch was not tested on any previous version of WT so I cannot be sure how to track it down unless I uninstall and go back to PL 8 which I know works. What I mean by the Synch never completes is that the last line it shows is:
Completed SynchNotification.
And then it never finishes, never deletes the rows from the Transaction Queues on either side, and I have to close out of the Synch Manager to get it to run again. If anyone else has had these problems, please let me know.
Thanks so much,
Kristen

Hi Kristen,
That one is tough.
How long have you allowed in to go before restarting? If the queues are large, it might take a while.
I would try opening up a SQL trace and seeing what is going on.
Also, you might run sp_who2 in SQL to see if processes are getting locked.
Do you have a synchplugin on this?

HT1926 Down loaded ITunes latest version,but intallation did not complete.Error message "invalid signature"

Upgraded my iTunes to the latest version(pc),it downloaded the new version but stopped during intallation.error message "invalid signature"

That suggests the installer is getting damaged during the download.
I'd first try downloading an installer from the Apple website using a different web browser:
http://www.apple.com/quicktime/download/
If you use Firefox instead of IE for the download (or vice versa), do you get a working installer?

Lion installer not completing

After downloading the Lion installer from the App Store, I tried to install over 10.6.8. Several attempts have failed. After maybe 3 minutes of running, the installer leaves me in the disk utility screen, with no way out except to choose one of 4 options, none of which are useful. If I quit the disk utility, I wind up booting in 10.6.8. My only guess is that the App Store download is flawed, but I see no way to repeat the download. Any ideas?

Update: I contacted Apple Support through the Express Lane option and was called by a rep. After listening to my problem he bounced me to a senior advisor. I have so far spent over 2 hours on the phone and much more on my own trying everything under the sun. The most recent was to do a clean installation of Snow Leopard on an unused disk partition, upgrade to 10.6.8, and try to install Lion. In every case it fails in exactly the same way. So far the installation log has been no help to the guy. What I was calling Disk Utilities is actually Os X Utilities, with 4 options other than quitting. The only option worth trying is to re-install OS X, which simply loops around to the same failure. I have sent him a dump from Profiler, but so far he sees nothing wrong with anything.

HP Solution Center device installation not complete

I have a PhotoSmart C7280 all-in-one printer running as an Ethernet networked printer. My personal PC is an HP Pavilion Slimline s5280t running Windows 7 Pro 64 bit. I've had the printer for longer than I've had the Pavilion. I use HP Solution Center at least once a month to copy documents to PDF for a volunteer job I have. Yesterday I tried to use it, and got the "device installation not complete" error. Uninstalling and reinstalling HP Solution Center didn't work. I did some research on the forums, and found the discussion of "the folders that start with 7Z."
I ran the Uninstall_L3.bat last night. It uninstalled everything. I then downloaded the drivers from the HP site, again. When I ran the install, it failed because "a file is missing." It didn't say what file. It created a "solution" for me, basically of going through all the steps to make sure that the printer and router were working (they are) and the printer was on the network (it is). I then downloaded the drivers AGAIN and AGAIN got a "file missing" error on the install. And my printer has been uninstalled. And I have a NEW suggestion from HP that I should reinstall after turning off all my startup tasks and rebooting.
If the driver package for the C7280 is defective, and right now I'd bet money that it is, telling me to turn off my startup list, which hasn't changed in months, is not going to help. Because my printer is out of warranty (hey, my PC is out of warranty), I don't expect any help from HP. I'm hoping that some other user will be able to suggest something that will work. I'm about ready to go back to the CD that came with the printer and install from that. Help?
This question was solved.
View Solution.

Sorry you have had such a difficult time getting Solution Center to work. You have certainly done all the basic and advanced steps to get this to work. I always keep a forum post stored on my computer that takes troubleshooting Solution Center to a different level of advanced.
--Problems Installing HP Solution Center - SOLUTION FOUND!--
I recommend reading this post thoroughly to review the comments and see how the steps play out and how certain problems are exposed. It certainly discusses the missing files you referenced.
I usually just scan using Paint or Windows Fax and Scan once I can print as it is just a little easier than working in the registry of an HP computer. So please do be careful if you choose to go into the registry.
First thing's first, I recommend creating another User Account in the Control panel with admin rights, then running the installation disk in the second user account before attempting anything in the above forum post. This will eliminate any conflicts from previous attempts on the main User Account.
I really hope this works for you! Let me know of any error messages you may get during the installation with the disk.
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!

At what point oracle write "Checkpoint not complete" in alert log ?

DB version: 10.2.0.4/RHEL 5.8
During a batch run, we encountered lots of 'Checkpoint not complete' errors in alert log.
Later we discovered that ORLs were sized only 50mb and this DB had only 3 redo log group. Since this is the potential cause, we are going create at least 10 Redo log groups and increase Redo log size to 500MB.
But , I want to know what exactly causes oracle to write "Checkpoint not complete" in alert log ?
For the purpose of this discussion, I am assuming we have only 1 ORL per redo log group. Is my below assumption correct ?
ORL1
|----------------> ORL1 file got full, so, LGWR starts writing to ORL2 file. Checkpoint occurs at log switch
|                    DBWR writes modified blocks associated with the redo entries in ORL1 to datafiles
|
V
ORL2
|----------------> ORL2 file got full, LGWR wants to start writing to ORL3 file. Checkpoint is initiated at log switch.
|                    But checkpoint can't be finished due to unknowN reasons
|
V
ORL3
|---------------->

Your assumption is only partly right.
I would illustrate it like
ORL1
|
|----------------> ORL1 file got full, so, LGWR starts writing to ORL2 file. Checkpoint occurs at log switch
|                    DBWR starts writing modified blocks associated with the redo entries in ORL1 to datafiles
|
V
ORL2
|----------------> ORL2 file got full, LGWR starts writing to ORL3 file.
|                    Checkpoint for ORL2 is initiated at log switch.
|
V
ORL3
|
|----------------> ORL3 file (the last member) also got full very quickly . LGWR wants to start the 'new cycle' by
                    writing (Reusing) to ORL1. But the checkpoint intiated by the log switch of ORL1 from the previous cycle is
                    not complete yet !! .
Basically you get this error when LGWR attempts to reuse an online redo log file (ORL1 in the above example) and finds that it cannot.
This is because the remaining ORL files (ORL2 and ORL3) got fully written before DB writer finished checkpointing the modified blocks associated with ORL1 yet.
Until the checkpoint of ORL1 is complete, the DB effectively hangs and user sessions have to wait until LGWR can safely reuse ORL1
Yes a larger redo log size of 10 groups can help. But make sure the I/O subsytem where ORLs are stored has no latency issues.

User Account keeps returning Transaction not complete - any ideas?

I configured TACACS+ and logged in with an account before creating the account and assigning it a role in the WAAS CM. I then figured out that I needed to create the account and assign it a role before I could actually do anything with the account. Now when I go into AAA users and try to create the account TACACS+ account that I had logged in with I keep getting the Transaction not complete error message. However, I am able to create other accounts with no issues.
From what I can tell it cached or added the TACACS+ account I first tried to login with and now will not allow me to create the account within WAAS CM. I can also go into my devices and click on the configuration icon for the CM WAAS, then select CM users and can see the account I'm trying to create.
Basically, I'm pretty sure it created the account when I logged in the first time and now it won't let me create it again. Since I can't modify or really even see the account it created in AAA users I can't assign it a role making it useless.
Any ideas?

You probably encountered CSCtj49204. Please go to the CM GUI -> My WAN -> Configure -> System Properties and set cdm.remoteuser.deletionDaysLimit to 1. Wait 24 hours after making that change and try again.
Sent from Cisco Technical Support iPhone App

Installation not completed - error at step# 10

Similar Messages

Maybe you are looking for