Installing 10g rac on Solaris 64-bit Sparc

I ran my preinstallation cluvufy
using ./cluvfy stage -pre crsinst -n racnode3,racnode4 -verbose -r 10gR2
I get failed errors at
1) Node connectivity failed
2) SUNWi15cs and SUNWi1cs- missing
3) Clock synchronization check using Network Time Protocol(NTP) failed
I am so lost as to figure out whats happening. have beenn working on it for two weeks now. Here is the log
Any help would be greatly appreciated
Thanks
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "racnode3"
Destination Node Reachable?
racnode3 yes
racnode4 yes
Result: Node reachability check passed from node "racnode3"
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
racnode4 passed
racnode3 passed
Result: User equivalence check passed for user "oracle"
Version of exectask could not be retrieved from node "racnode3"
Checking node connectivity...
Checking hosts config file...
Node Name Status Comment
racnode4 passed
Verification of the hosts config file successful
Interface information for node "racnode4"
Name IP Address Subnet Gateway Def. Gateway HW Address MTU
vnet0 10.23.11.127 10.23.11.0 10.23.11.127 10.23.11.1 00:14:4F:FB:A4:A5 1500
vnet1 192.168.2.127 192.168.0.0 192.168.2.127 10.23.11.1 00:14:4F:F8:5A:A3 9216
Check: Node connectivity of subnet "10.23.11.0"
Result: Node connectivity passed for subnet "10.23.11.0" with node(s) racnode4
Check: TCP connectivity of subnet "10.23.11.0"
Source Destination Connected?
racnode3:10.23.11.126 racnode4:10.23.11.127 failed
ERROR:
PRVF-7617 : Node connectivity between "racnode3 : 10.23.11.126" and "racnode4 : 10.23.11.127" failed
Result: TCP connectivity check failed for subnet "10.23.11.0"
Check: Node connectivity of subnet "192.168.0.0"
Result: Node connectivity passed for subnet "192.168.0.0" with node(s) racnode4
Check: TCP connectivity of subnet "192.168.0.0"
Source Destination Connected?
racnode3:10.23.11.126 racnode4:192.168.2.127 failed
ERROR:
PRVF-7617 : Node connectivity between "racnode3 : 10.23.11.126" and "racnode4 : 192.168.2.127" failed
Result: TCP connectivity check failed for subnet "192.168.0.0"
Interfaces found on subnet "10.23.11.0" that are likely candidates for VIP are:
racnode4 vnet0:10.23.11.127
WARNING:
Could not find a suitable set of interfaces for the private interconnect
Result: Node connectivity check failed
Check: Total memory
Node Name Available Required Comment
racnode4 5.75GB (6029312.0KB) 1GB (1048576.0KB) passed
Result: Total memory check passed
Check: Swap space
Node Name Available Required Comment
racnode4 8GB (8388600.0KB) 5.75GB (6029312.0KB) passed
Result: Swap space check passed
Check: Free disk space for "racnode4:/var/tmp/"
Path Node Name Mount point Available Required Comment
/var/tmp/ racnode4 / 11.8299GB 400MB passed
Result: Free disk space check passed for "racnode4:/var/tmp/"
Check: User existence for "oracle"
Node Name Status Comment
racnode4 exists(200) passed
Checking for multiple users with UID value 200
Result: Check for multiple users with UID value 200 passed
Result: User existence check passed for "oracle"
Check: User existence for "nobody"
Node Name Status Comment
racnode4 exists(60001) passed
Checking for multiple users with UID value 60001
Result: Check for multiple users with UID value 60001 passed
Result: User existence check passed for "nobody"
Check: Group existence for "oinstall"
Node Name Status Comment
racnode4 exists passed
Result: Group existence check passed for "oinstall"
Check: Group existence for "dba"
Node Name Status Comment
racnode4 exists passed
Result: Group existence check passed for "dba"
Check: Membership of user "oracle" in group "oinstall" [as Primary]
Node Name User Exists Group Exists User in Group Primary Comment
racnode4 yes yes yes yes passed
Result: Membership check for user "oracle" in group "oinstall" [as Primary] passed
Check: Membership of user "oracle" in group "dba"
Node Name User Exists Group Exists User in Group Comment
racnode4 yes yes yes passed
Result: Membership check for user "oracle" in group "dba" passed
Check: Run level
Node Name run level Required Comment
racnode4 3 3 passed
Result: Run level check passed
Check: Hard limits for "maximum open file descriptors"
Node Name Type Available Required Comment
racnode4 hard 65536 65536 passed
Result: Hard limits check passed for "maximum open file descriptors"
Check: Soft limits for "maximum open file descriptors"
Node Name Type Available Required Comment
racnode4 soft 1024 1024 passed
Result: Soft limits check passed for "maximum open file descriptors"
Check: Hard limits for "maximum user processes"
Node Name Type Available Required Comment
racnode4 hard 16384 16384 passed
Result: Hard limits check passed for "maximum user processes"
Check: Soft limits for "maximum user processes"
Node Name Type Available Required Comment
racnode4 soft 16384 2047 passed
Result: Soft limits check passed for "maximum user processes"
Check: System architecture
Node Name Available Required Comment
racnode4 64-bit sparcv9 kernel modules 64-bit sparcv9 kernel modules passed
Result: System architecture check passed
Check: Kernel version
Node Name Available Required Comment
racnode4 5.10-2011.08.23.15.26 5.10-2005.01 passed
Result: Kernel version check passed
Check: Kernel parameter for "project.max-sem-ids"
Node Name Configured Required Comment
racnode4 128 100 passed
Result: Kernel parameter check passed for "project.max-sem-ids"
Check: Kernel parameter for "process.max-sem-nsems"
Node Name Configured Required Comment
racnode4 512 256 passed
Result: Kernel parameter check passed for "process.max-sem-nsems"
Check: Kernel parameter for "project.max-shm-memory"
Node Name Configured Required Comment
racnode4 4294967296 4294967295 passed
Result: Kernel parameter check passed for "project.max-shm-memory"
Check: Kernel parameter for "project.max-shm-ids"
Node Name Configured Required Comment
racnode4 128 100 passed
Result: Kernel parameter check passed for "project.max-shm-ids"
Check: Package existence for "SUNWarc-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWarc-11.10.0-2005.01.21.15.53 SUNWarc-...( sparc) passed
Result: Package existence check passed for "SUNWarc-...( sparc)"
Check: Package existence for "SUNWbtool-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWbtool-11.10.0-2005.01.21.15.53 SUNWbtool-...( sparc) passed
Result: Package existence check passed for "SUNWbtool-...( sparc)"
Check: Package existence for "SUNWhea-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWhea-11.10.0-2005.01.21.15.53 SUNWhea-...( sparc) passed
Result: Package existence check passed for "SUNWhea-...( sparc)"
Check: Package existence for "SUNWlibC-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWlibC-5.10-2004.12.22 SUNWlibC-...( sparc) passed
Result: Package existence check passed for "SUNWlibC-...( sparc)"
Check: Package existence for "SUNWlibm-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWlibm-5.10-2004.12.18 SUNWlibm-...( sparc) passed
Result: Package existence check passed for "SUNWlibm-...( sparc)"
Check: Package existence for "SUNWlibms-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWlibms-5.10-2004.11.23 SUNWlibms-...( sparc) passed
Result: Package existence check passed for "SUNWlibms-...( sparc)"
Check: Package existence for "SUNWsprot-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWsprot-5.10-2004.11.23 SUNWsprot-...( sparc) passed
Result: Package existence check passed for "SUNWsprot-...( sparc)"
Check: Package existence for "SUNWtoo-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWtoo-11.10.0-2005.01.21.15.53 SUNWtoo-...( sparc) passed
Result: Package existence check passed for "SUNWtoo-...( sparc)"
Check: Package existence for "SUNWi1of-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWi1of-6.6.2.7400-0.2004.12.15 SUNWi1of-...( sparc) passed
Result: Package existence check passed for "SUNWi1of-...( sparc)"
Check: Package existence for "SUNWi1cs-...( sparc)"
Node Name Available Required Comment
racnode4 missing SUNWi1cs-...( sparc) failed
Result: Package existence check failed for "SUNWi1cs-...( sparc)"
Check: Package existence for "SUNWi15cs-...( sparc)"
Node Name Available Required Comment
racnode4 missing SUNWi15cs-...( sparc) failed
Result: Package existence check failed for "SUNWi15cs-...( sparc)"
Check: Package existence for "SUNWxwfnt-...( sparc)"
Node Name Available Required Comment
racnode4 SUNWxwfnt-6.6.2.7400-0.2004.12.15 SUNWxwfnt-...( sparc) passed
Result: Package existence check passed for "SUNWxwfnt-...( sparc)"
Checking for multiple users with UID value 0
Result: Check for multiple users with UID value 0 passed
Check: Current group ID
ERROR:
PRVF-5502 : Current group ID check cannot be performed
Result: Current group ID check failed
Starting Clock synchronization checks using Network Time Protocol(NTP)...
NTP Configuration file check started...
The NTP configuration file "/etc/inet/ntp.conf" is available on all nodes
NTP Configuration file check passed
Checking daemon liveness...
Check: Liveness for "xntpd"
Node Name Running?
racnode4 yes
Result: Liveness check passed for "xntpd"
Check for NTP daemon or service alive passed on all nodes
Checking NTP daemon command line for slewing option "'slewalways yes' & 'disable pll'"
Check: NTP daemon command line
Node Name Slewing Option Set?
racnode4 no
Result:
NTP daemon slewing option check failed on some nodes
PRVF-5436 : The NTP daemon running on one or more nodes lacks the slewing option "'slewalways yes' & 'disable pll'"
Result: Clock synchronization check using Network Time Protocol(NTP) failed
Checking Core file name pattern consistency...
Core file name pattern consistency check passed.
Checking to make sure user "oracle" is not in "root" group
Node Name Status Comment
racnode4 does not exist passed
Result: User "oracle" is not part of "root" group. Check passed
Check default user file creation mask
Node Name Available Required Comment
racnode4 0022 0022 passed
Result: Default user file creation mask check passed
Checking consistency of file "/etc/resolv.conf" across nodes
Checking the file "/etc/resolv.conf" to make sure only one of domain and search entries is defined
File "/etc/resolv.conf" does not have both domain and search entries defined
Checking if domain entry in file "/etc/resolv.conf" is consistent across the nodes...
domain entry in file "/etc/resolv.conf" is consistent across nodes
Checking if search entry in file "/etc/resolv.conf" is consistent across the nodes...
search entry in file "/etc/resolv.conf" is consistent across nodes
Checking file "/etc/resolv.conf" to make sure that only one search entry is defined
All nodes have one search entry defined in file "/etc/resolv.conf"
Checking DNS response time for an unreachable node
Node Name Status
racnode4 passed
The DNS response time for an unreachable node is within acceptable limit on all nodes
File "/etc/resolv.conf" is consistent across nodes
Check: Time zone consistency
Result: Time zone consistency check passed
Pre-check for cluster services setup was unsuccessful on all the nodes.
Edited by: Aj05 on Feb 2, 2012 8:26 AM

Daniel,
Again ... my initial response was that I was insulted by the implications: Still am.
Perhaps you are hoping someone else will steal that copywrited material and send it to you? Is that what you are asking?I think your initial response is little bit excessive (IMO). OP didn't say that "Somebody steal the content from metalink and send it to me please". He might requesting specific note id for appropriate document which describes installation in "instant" form.
But do you really think, for even one minute, that anyone who has invested many hundreds of hours into creating a training class is going to send you their materials for free?Somebody called "Linus" and many others invested many hundreds of hours to create OS which you are using for free (and you are recommending it in your posts)... ;-)
What if there is some altruist which could provide the such complex paper for RAC?
Your third post is correct and I absolutely agree with you (except last sentence).
Salman,
you can look to get inspired at "DBA" articles on OTN website (http://www.oracle.com/technology/pub/articles/tech_dba.html#linux) or RAC SIG site and compare it with official documentation or metalink notes. Only documentation and metalink notes are 100% assurance that your installation/configuration will be supported. And in case of doubts you still can contact Oracle support and consult planned steps/implementation.
Message was edited by:
Ivan Kartik
s/second post/third post/

Similar Messages

De-installing 10g RAC on Solaris 10

Hi,
Does anyone knows how to manually de-installing 10g rac on solairs 10?
I did not following the correct steps to de-install RAC from the RAC installation Guide.
I need to reuse this host for non-rac 10gr2 on different ORACLE_HOME.
./localconfig reset $ORACLE_HOME
Oracle CSS service would not start as installed
Automatic Storage Management(ASM) cannot be used until Oracle CSS service is started
cat ./log/wchost/alertwchost.log
[client(9029)]CRS-1006:The OCR location /oracle/product/10.2.0/cdata/localhost/local.ocr is inaccessible. Details in /oracle/product/10.2.0/log/wchost/client/clscfg_9029.log.
Thanks!
R

Metalink Note 239998.1 tells you how to tidy things up after installation and deinstallation problems

10g RAC on SOLARIS 10

Hi,
What is the best CLUSTER I can use for my 10g RAC on SOLARIS 10.
Regards
MMU

I am going to install Oracle 10g RAC (standard Edition) on Solaris 10 (sparc 64bit).I am using Oracle Clustware only.I need step by step document for this installation.I have gone through Oracle documents and many others.I have failed many times in this installation so I need some good document.
Plz tell me what directories I need to create and permission for this directories.
I am creating these directories before starting CRS installation.
mkdir -p /opt/oracle/product/10.2.0/crs
chown -R root:oinstall /opt/oracle/product/10.2.0/crs
chmod -R 775 /opt/oracle/product/10.2.0/crs
mkdir -p /opt/oracle/product/10.2.0/db_1
chown -R root:oinstall /opt/oracle/product/10.2.0/db_1
chmod -R 775 /opt/oracle/product/10.2.0/db_1
mkdir -p /opt/oracle/admin
chown -R root:oinstall /opt/oracle/admin
chmod -R 775 /opt/oracle/admin
mkdir -p /var/tmp/.oracle
mkdir -p /tmp/.oracle
mkdir -p /var/opt/oracle
chown -R oracle:oinstall /var/tmp/.oracle
chown -R oracle:oinstall /tmp/.oracle
chown -R oracle:oinstall /var/opt/oracle

Configring and instaling 10g RAC on two Nods win 2003 Local Area

All Experts
I want to configure and instal 10g RAC using three database server on difirent network groups (Head office , processing, stitching). i am unable to configure ip etc. ip address is as:
work group ip address computer name
HO 192.168.0.29 maindb
processing 192.168.1.92 procdb
stitching 192.168.1.92 stichdb
Please guide how i can configure and user hosts file in windows\system32\drivers\etc\hosts
Thanks in advance

Thanks
i have three server with same subnet mask. save os and db versiong windows server 2003 and 10g on all servers.
server-1
ip address : 192.168.0.29
ubnet mask : 255.255.254.0
computer name : maindb
server-2
ip address : 192.168.0.92
ubnet mask : 255.255.254.0
computer name : procdb
server-3
ip address : 192.168.0.93
ubnet mask : 255.255.254.0
computer name : stitchdb
Please guide me how i can configure system32\dirvers\etc\hosts file.
Thanks in advance.

10g rac on solaris

Dear all,
We are in the process of installtion of 10g RAC on solaris.
As far as i studied,
OCFS cannot be used in Solaris
Only 3rd party cluster file system can be used
if no 3 party cluster file system can be used,we have to use ASM
Is there any other options for this ?
Please guide
Kai

pls, i need an help urgently with installation of RAC on Solaris Using VMware.
i recieved the following error: PRIF-12:failed to initialize cluster support services
Pls, can u mail([email protected]) or make available the content in this location...someone in the forum
refer someone having almost the same difficulties to this location :
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=395697.1
thanks a zillon for your assistance.

10g RAC on Solaris 10 containers - Question on Approach

Hi All
To introduce a little, I am trying to set-up 10g RAC (active-active) on Solaris 10 Containers. For the disaster recovery site, I was considering an option for storage replication across datacenters. As I look at the situation where the database could be highly transactional, I wanted to go for this option hoping I might be better able to recover db on dr site if a failure happens and also alleviate some load from the prod servers. In this regard I have a set of questions for which if you could share your experiences, thoughts .. I am sure will help my preperation.
1 Is Oracle Supported on Solaris 10 containers? I believe it is not supported and ofcourse am getting into the certification matrix for this with oracle. Anyways, any work around tried out by anyone ?
2 Which product is better in terms of performance while co-existing and co-functioning with Oracle? Sun Cluster!!! Vertas Cluster!!! any other? I am unable to link to any recommendations from Oracle and hence trying to understand the generic or say standard approach to this.
3 I understand on Prod site, Oracle remains active-active on two node cluster while I will mirror my SAN between Prod site and DR site on a timely basis, while DB is up and running. This mirroring has to be only an asynchronous mirroring for some limitations. I am unsure about my recoverability if we need to switch over to DR. Will I be able to recover the Database to a point when my last mirroring has been completed successfully when I say the mirroring happened while the Prod db is up and running (hot backup type on disk level). Until now I used a cold backup for Storage replication and I was sure to bring it up there. This hot backup kind of attempt is raising unrest and questions about the abilities.. :-(
4 I also have come across a term called federated databases? Is it similar to what I am trying to achieve here? Storage level replocation across data centres?
I know it takes some time to get to the end of it and finally implement it, but your inputs will certainly help me get things straight before I hit this first click. Thanks for all your inputs, advices, suggestions. :-)
Regards!
Sarat

According to Oracle "Both Oracle 9i R2 and 10g R2 databases have been certified to run in a Solaris Container."
There are references here :- http://forums.sun.com/thread.jspa?threadID=5397695
"Oracle databases (RAC and non-RAC) have been certified to run in a global Solaris 10 Container"
What storage are you using ? (filesystem, ASM ?) Personally I prefer ASM now, but it does depend on the storage platform and backup strategy.
What backup infrastructure do you have ? RMAN backup directly to tape is better than file copy.
For DR standby purposes I would use Dataguard instead of disk mirroring / storage replication. It is much more flexible (e.g can switch direction of replication, do incremental backups from the standby etc).
I would use CRS instead of VCS. CRS is built for the job, and integrates with netca, dbca, etc for service management, and also integrates with Dataguard Broker for standby switchover.

Installing 10g client on windows7 64 bit. ( 11g r2 already installed)

I am a fiscal auditor auditing data on databases with hundreds of millions rows. So not a professional database expert.
I have Oracle 11.2.0.1.0 installed on Windows 7 64 bit ultimate
I want to import data from warehouse which has Oracle 10.2.0.4.0 installed.
When I try to import
impdp usr/pass@WAREHOUSE TABLES=TABLE DIRECTORY=DATA_PUMP_DIR NETWORK_LINK=D_W VERSION=10.2
It gives :
UDI-00018: Data Pump client is incompatible with database version 10.2.0.4.0
To overcome version incompatibility, I think I need to install 10g client on my computer.
But I already have 11gr2 database installed, so I wanted to learn about potential problems.
Especially about having two Oracle Homes, tnsnames.ora files, which 10g client version, etc..
Step by step explanation is highly appreciated.
Thanks.

orafad wrote:
Are you connected to the target or source database with impdp? Db link for source db to be used in NETWORK_LINK argument, in which database does it exist?
Again, show impdp command session (copy-paste)
orafad thanks, I understand my mistake but I encountered a new one.
I was using source username/pass for impdp, it was wrong I should use target username.
Here is the result now:
SQLPlus: Release 11.2.0.1.0 Production on Pzt Ara 26 13:52:58 2011*
Copyright (c) 1982, 2010, Oracle. All rights reserved.
Enter user-name: target_usr
Enter password:
Connected to:
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
*> $*
*Microsoft Windows [Sürüm 6.1.7600]*
Telif Hakkı (c) 2009 Microsoft Corporation. Tüm hakları saklıdır.
D:\app\direct\product\11.2.0\dbhome_1\BIN>impdp target_usr/target_pass network_link=ambar
Import: Release 11.2.0.1.0 - Production on Pzt Ara 26 13:53:23 2011
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
Connected to: Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
ORA-31631: privileges are required
ORA-39149: cannot link privileged user to non-privileged user
Source schema has the exp_full_database privilege, so I don't understand why this happens.
select privilege from user_sys_privs minus select privilege from user_sys_privs@ambar;
     PRIVILEGE
1     ALTER TABLESPACE
2     CREATE TABLESPACE
3     DROP TABLESPACE
select privilege from user_sys_privs@ambar minus select privilege from user_sys_privs;
     PRIVILEGE
1     CREATE ANY VIEW
2     ENQUEUE ANY QUEUE
3     EXECUTE ANY CLASS
4     EXECUTE ANY EVALUATION CONTEXT
5     EXECUTE ANY INDEXTYPE
6     EXECUTE ANY LIBRARY
7     EXECUTE ANY OPERATOR
8     EXECUTE ANY PROCEDURE
9     EXECUTE ANY PROGRAM
10     EXECUTE ANY RULE
11     EXECUTE ANY RULE SET
12     EXECUTE ANY TYPE
13     EXEMPT ACCESS POLICY
14     EXEMPT IDENTITY POLICY
15     EXPORT FULL DATABASE
16     FLASHBACK ANY TABLE
17     FORCE ANY TRANSACTION
18     FORCE TRANSACTION
19     SELECT ANY TABLE
select granted_role from user_role_privs minus select granted_role from user_role_privs@ambar;
     GRANTED_ROLE
1     IMP_FULL_DATABASE

How to Install OBIEE in Sun Solaris 64 Bit OS?

Dear All,
Is any one can help me with screen shot on Installation of OBIEE in Sun Solaris 64 Bit (version 10) OS. OBIEE Version 10.1.3.4
Also required a check list of Pre-Installation mandate requirements.
Thanks & Regards
OBIEE Functional Consultant

OBIEE documentation: http://download.oracle.com/docs/cd/E10415_01/doc/nav/portal_1.htm where you can find the System Requirements and Supported Platforms guide and the installation guide.
Regarding screen shots: http://catb.org/esr/faqs/smart-questions.html#homework
PS: I wouldn't call myself an "OBIEE Consultant" if I couldn't find the OBIEE documentation or needed screen shots to install OBIEE.

10g RAC on RHEL4 64 Bit

Hi,
Can any one please help me finding out a step by step installation guide (other than 10g documentation) of ORacle 10g RAC on Red Har Enterprise Linux 4 (64 bit) either available on oracle web site, metalink OR from any other web site.
Thanks

Daniel,
Again ... my initial response was that I was insulted by the implications: Still am.
Perhaps you are hoping someone else will steal that copywrited material and send it to you? Is that what you are asking?I think your initial response is little bit excessive (IMO). OP didn't say that "Somebody steal the content from metalink and send it to me please". He might requesting specific note id for appropriate document which describes installation in "instant" form.
But do you really think, for even one minute, that anyone who has invested many hundreds of hours into creating a training class is going to send you their materials for free?Somebody called "Linus" and many others invested many hundreds of hours to create OS which you are using for free (and you are recommending it in your posts)... ;-)
What if there is some altruist which could provide the such complex paper for RAC?
Your third post is correct and I absolutely agree with you (except last sentence).
Salman,
you can look to get inspired at "DBA" articles on OTN website (http://www.oracle.com/technology/pub/articles/tech_dba.html#linux) or RAC SIG site and compare it with official documentation or metalink notes. Only documentation and metalink notes are 100% assurance that your installation/configuration will be supported. And in case of doubts you still can contact Oracle support and consult planned steps/implementation.
Message was edited by:
Ivan Kartik
s/second post/third post/

Installing 10g RAC on laptop

Hi,
Has anybody got a note or a good link of how-to for the installation of 10g RAC on laptop using redhat or suse?
Please provide it as I am looking to start my hands on RAC.
Thanks

Here:
http://www.oracle.com/pls/db102/portal.portal_db?selected=16
http://www.oracle-base.com/articles/10g/OracleDB10gR2RACInstallationOnCentos4UsingVMware.php

Patch RAC 10.2.0.1 Solaris 64 bit SPARC

I am trying to upgrade CRS to the most recent version. But could not find the patch number.
Patch 5337014 looks like a database patch, not CRS. Can someone confirm this.
Thanks
-Prasad

After i install the patch, instance on Node 1 does not come back. It looks like diskgroup1 is dis-mounted. How do i mount it back ?
Patch Details
cd /opt/app/oracle/product/10.2.0/db_1/bin/
bash-3.00# ./crsctl stop crs
cd /opt/app/oracle/product/10.2.0/db_1/install
bash-3.00# ./root102.sh
I had applied the patch on node1 only and the patch took the node down. 2nd node is fine.
$ srvctl start instance -d STAG -i STAG1
PRKP-1001 : Error starting instance STAG1 on node ora-v240-s01
CRS-0215: Could not start resource 'ora.STAG.STAG1.inst'.
SQL> select group_number, name, STATE from v$asm_diskgroup;
GROUP_NUMBER NAME STATE
0 STAGRAC_DATA DISMOUNTED
2 STAGRAC_FLASH MOUNTED
SQL> alter diskgroup stagrac_data mount;
alter diskgroup stagrac_data mount
ERROR at line 1:
ORA-15032: not all alterations performed
ORA-15024: discovered duplicately numbered ASM disk 1
Thanks
-Prasad

Error ORA-12546 installing 10g on Windows XP 64 bit

when installing ora 10g on my windows xp 64 bit professional
I get an ORA-12546 error. this happens while setup is creating the default database.
I get this error also when creating a database instance manually.
is there a workarounnd for this problem?
thanks a lot.
florian

Has the listener service started successfully in the services applet? Check the event log on the windows to see if there is anything additional for these messages.

How to install 3c905c NIC in Solaris 8 in SPARC platform

i bought a 3c905c NIC. I want to install it into SUN Blade 100 (SPARC platform) Solaris 8. I do need help how can I configure this NIC?tks.

From what I have seen the SPARC based systems don't have drivers for anything other than Sun hardware. I am presently working on a 3C90x and Intel Pro/100 driver for the Ultra Sparc series.
James

Will Instant Client 10.2.0.1 be available for Solaris 32-bit (SPARC)?

The latest Instant Client release is currently not available for Solaris Sparc 32-bit.
Does anyone know when it will be available?
Thank you.

It is available now.

Install 10g RAC on solaris10(x86) in VMware,but failed on crs's root.sh

VMware server 1.0.4 build-56528
bash-3.00# uname -a
SunOS rac02 5.10 Generic_118855-33 i86pc i386 i86pc
disk information:
format->partition->print,this is the result
Current partition table (original):
Total disk cylinders available: 3580 + 2 (reserved cylinders)
Part Tag Flag Cylinders Size Blocks
0 usr wm 3 - 5 6.00MB (3/0/0) 12288
1 usr wm 76 - 95 40.00MB (20/0/0) 81920
2 backup wu 0 - 3579 6.99GB (3580/0/0) 14663680
3 usr wm 96 - 2000 3.72GB (1905/0/0) 7802880
4 usr wm 2001 - 3579 3.08GB (1579/0/0) 6467584
5 usr wm 6 - 75 140.00MB (70/0/0) 286720
6 unassigned wm 0 0 (0/0/0) 0
7 unassigned wm 0 0 (0/0/0) 0
8 boot wu 0 - 0 2.00MB (1/0/0) 4096
9 unassigned wm 0 0 (0/0/0) 0
i want to save ocr and voting on raw partition,ocr on 5(140m) and vot on 1(40m)
then,i do as this,
bash-3.00# ln -s /dev/rdsk/c2t0d0s5 /orac/ora_ocr
bash-3.00# ln -s /dev/rdsk/c2t0d0s1 /orac/ora_vot
bash-3.00# chown -RL root:oinstall /orac/ora_ocr
bash-3.00# chown -RL oracle:oinstall /orac/ora_vot
bash-3.00# chmod 777 /orac/ora_ocr
bash-3.00# chmod 777 /orac/ora_vot
this is the error message:
bash-3.00# /orac/crs/product/10.2.0/root.sh
WARNING: directory '/orac/crs/product' is not owned by root
Checking to see if Oracle CRS stack is already configured
Setting the permissions on OCR backup directory
Setting up NS directories
Oracle Cluster Registry configuration upgraded successfully
WARNING: directory '/orac/crs/product' is not owned by root
Successfully accumulated necessary OCR keys.
Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
node <nodenumber>: <nodename> <private interconnect name> <hostname>
node 1: rac01 node1 rac01
node 2: rac02 node2 rac02
Creating OCR keys for user 'root', privgrp 'root'..
Operation successful.
Now formatting voting device: /orac/ora_vot
CLSFMT returned with error [4].
Failed to initialize Oracle Cluster Registry for cluster
0
What is wrong?
I have other questions,
A.Before install CRS,do i need some packages?SUNWarc SUNWbtool SUNWhea SUNWlibm SUNWlibms SUNWsprot SUNWtoo SUNWi1of SUNWi1cs SUNWi15cs SUNWxwfnt,install guide told me these packages is necessary,but someone told me it wrote for solaris 9
B.How can i use the raw device?
C.Do i need the sun cluster?

These machines are in vmware server,and I use "vmware-vdiskmanager -c -s 250Mb -a lsilogic -t 2 "D:\10gRAC\votedisk.vmdk"" to create the shared storage.
-thanks

Installing 10g rac on Solaris 64-bit Sparc

Similar Messages

Maybe you are looking for