Intel 7260 and Sattelite a665

I just replaced the Intel Advanced 6200 wifi card in my Sattelite A665 with an Intel 7260 2x2 ac wifi card to utilize the ac capability of my new Newgear AC1900 router. I downloaded and installed the newest drivers from Intel and Device manager shows the both the wifi and blue tooth portions of the card working properly and I now have blue tooth connection to my HP printer. I can not see any of my previous wifi connections and Windows 7 trouble shooting says the wifi hardware swith is Off. The "Radio" button does seem to swith the radio on/off, however the orange led light on the front of the laptop doesn't come on like it did with the 6200 card. Is there a compatiblility issue with the A665 and the 7260 card or something else I'm missing. I'm running Win 7 Premium Home Edition with SP1.

I'm still working on this and discovered I was using the wrong Hardware Switch to toggle the wireless mode off and on. there is a shortcut button to the wireless mode above the function keys that is supposed to toggle wireless on/off. I noticed it doesn't work if when the original Intel 6200 wifi card was in. However the true on/off is FN key + F8. That works with the original card. I put the new Intel 7260 in and it installs perfectly with device manager indicating it is working properly and the bluetooth works great too......but no wifi. Then I notice the F8 functionality is now gone so I can not use the hardware switch to turn wifi on.
Has the Toshiba system locked that card out from being funtional on this computer? Any other thoughts? I've tried just about everything discussed on various forums and sites.

Similar Messages

X140e and Intel 7260 (FRU: 04W3814)

Hey! I just got my hands on a X140e thinkpad. I wanted to install Linux on it.
According to https://wiki.archlinux.org/index.php/Lenovo_ThinkPad_X140e#Wireless , an aftermarket intel card with FRU 04W3814 should work. The Intel card is also mentioned in the 2.06 BIOS update: http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/gsuj07uc.txt:
- (New) Added support for the Wireless LAN adapter (Intel 7260).
I assumed I just need to:
Update the BIOS (I updated to 2.06)
Switch the cards
Updating the Bios to 2.06 went fine, after installing the card however I can't seem to see it. It doesn't show up in "lspci" and in Windows, it shows up in the device manager, but just as a generic network card and with a yellow exclamation point.
Am I missing something? Are there any additional steps necessary?
For reference, I bought this card: http://www.ebay.com/itm/261541641863
The sticker does mention the FRU

Hello,
Have you tried installing the drivers for the Intel 7260 card while in Windows?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Intel 7260 compatibility before buying a new Envy laptop

Does anyone know if the new envy 17t or 15t laptops with i7 processors are compatible with the intel 7260 ac wireless card or are the new laptops still whitelisted? Looking for laptop that is able to use this card.

The current Envy 17t and 15t models have no BIOS whitelist so you can add an ac card with no issues.

Will FRU 04W3814 pass whitelist (intel 7260 AC Wifi Card)

Will FRU 04W3814 pass whitelist (intel 7260 AC Wifi Card) in a G580 20157?
Solved!
Go to Solution.

hi johnblaazer,
Thanks for Posting!
With the G580 Whitelist,
Im thinking that this will not work.
Here is the List for the G580
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Tip: Temp work around for Intel 7260 wireless card problems

I am currently having lot of issues with the Intel 7260 wireless card relating to unstable network connections (i.e. limited or no network connections, frequent dropouts). These problems are quite widespread, so it is not limited to Lenovo branded machines, many other brand of laptops are also having similar problem. This workaround is temporary until the laptop company and intel provides an official fix.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Step 1. Go into your control panel -> System Security -> System
Step 2. Click on Device Manager on the left hand side of the window.
Step 3. Click on Network Adapters
Step 4. Right click on Intel Wireless 7260, and click on properties
Step 5. Click on Advanced Tab
Step 6. Click on HT Mode and then select disable as an option.
Disabling the HT mode means you are operating the wireless card in G mode (54 mbps), for some people this is too slow, but it is an acceptable short term solution for preventing frequent network connection dropouts.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Wifi issue on System76 (Intel 7260)

Hi all,
I've been having this issue on certain wireless networks where the wireless just stops working but stays connected and the only indication anything is wrong is when you go to load a page.
All I have to go in is the dmesg:
[ 3904.597032] ------------[ cut here ]------------
[ 3904.597061] WARNING: CPU: 4 PID: 2271 at net/wireless/reg.c:1806 reg_process_hint+0x2d1/0x460 [cfg80211]()
[ 3904.597063] Modules linked in: fuse ctr ccm snd_hda_codec_hdmi joydev mousedev ec_sys bnep ecb btusb i915 bluetooth snd_hda_codec_via snd_hda_codec_generic 6lowpan_iphc drm_kms_helper snd_hda_intel snd_hda_controller vboxdrv(O) drm snd_hda_codec intel_gtt snd_hwdep tpm_infineon arc4 btrfs xor snd_pcm mac_hid i2c_algo_bit tpm_tis mei_me raid6_pq iwlmvm led_class mac80211 iTCO_wdt iTCO_vendor_support evdev iwlwifi cfg80211 rfkill rtsx_pci_ms memstick psmouse i2c_i801 pcspkr mei serio_raw tpm shpchp lpc_ich nfs coretemp hwmon x86_pkg_temp_thermal intel_powerclamp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd microcode snd_timer i2c_core thermal snd soundcore e1000e ptp pps_core video lockd ac processor
[ 3904.597125] battery wmi button sunrpc fscache ext4 crc16 mbcache jbd2 sd_mod crc_t10dif crct10dif_common rtsx_pci_sdmmc mmc_core atkbd libps2 ahci libahci libata ehci_pci xhci_hcd ehci_hcd scsi_mod usbcore rtsx_pci usb_common i8042 serio
[ 3904.597151] CPU: 4 PID: 2271 Comm: kworker/4:1 Tainted: G W O 3.16.2-1-ck #1
[ 3904.597154] Hardware name: System76, Inc. Galago UltraPro/W740SU , BIOS 4.6.5 12/12/2013
[ 3904.597162] Workqueue: events reg_todo [cfg80211]
[ 3904.597165] 0000000000000000 000000000c67a316 ffff88036aaa7d50 ffffffff81508c6b
[ 3904.597169] 0000000000000000 ffff88036aaa7d88 ffffffff8106cffd ffff8803c2c6c300
[ 3904.597173] ffff880408690260 ffff8803c2c6c31c ffff88041fb17600 0ffff88041fb1760
[ 3904.597177] Call Trace:
[ 3904.597185] [<ffffffff81508c6b>] dump_stack+0x4d/0x6f
[ 3904.597191] [<ffffffff8106cffd>] warn_slowpath_common+0x7d/0xa0
[ 3904.597195] [<ffffffff8106d12a>] warn_slowpath_null+0x1a/0x20
[ 3904.597203] [<ffffffffa04b1311>] reg_process_hint+0x2d1/0x460 [cfg80211]
[ 3904.597211] [<ffffffffa04b1519>] reg_todo+0x79/0x1a0 [cfg80211]
[ 3904.597218] [<ffffffff8108989b>] process_one_work+0x16b/0x460
[ 3904.597222] [<ffffffff81089edb>] worker_thread+0x6b/0x550
[ 3904.597227] [<ffffffff81089e70>] ? init_pwq.part.25+0x10/0x10
[ 3904.597232] [<ffffffff8109019a>] kthread+0xea/0x100
[ 3904.597236] [<ffffffff810900b0>] ? kthread_create_on_node+0x1b0/0x1b0
[ 3904.597240] [<ffffffff8150eefc>] ret_from_fork+0x7c/0xb0
[ 3904.597244] [<ffffffff810900b0>] ? kthread_create_on_node+0x1b0/0x1b0
[ 3904.597246] ---[ end trace 280abc5ce5b473e3 ]---
[ 3904.597249] cfg80211: Calling CRDA for country: US
[ 4145.061302] wlp3s0: authenticate with c8:f9:f9:a0:32:0f
[ 4145.063818] wlp3s0: send auth to c8:f9:f9:a0:32:0f (try 1/3)
[ 4145.064093] cfg80211: Calling CRDA to update world regulatory domain
[ 4145.064516] wlp3s0: authenticated
[ 4145.065486] wlp3s0: associate with c8:f9:f9:a0:32:0f (try 1/3)
[ 4145.067271] wlp3s0: RX AssocResp from c8:f9:f9:a0:32:0f (capab=0x11 status=0 aid=2)
[ 4145.068136] wlp3s0: associated
[ 4145.068185] cfg80211: Calling CRDA to update world regulatory domain
[ 4145.372574] cfg80211: Calling CRDA to update world regulatory domain
Everything I have found on the issue seems to be older and people solve it by updating firmware, I have check my firmware and I have the newest ones that others have said solved their issue:
[andrew@Andrew-Ultrapro ~]$ ls -al /lib/firmware/ | grep 7260
-rw-r--r-- 1 root root 683236 Aug 28 12:08 iwlwifi-7260-7.ucode
-rw-r--r-- 1 root root 679780 Aug 28 12:08 iwlwifi-7260-8.ucode
-rw-r--r-- 1 root root 679380 Aug 28 12:08 iwlwifi-7260-9.ucode
Any help at all resolving this would be greatly appreciated.

I am only familiar with the Intel 7260/7265. They have a setting called U-APSD.
If this is enabled you will see this behaviour.
If you find this setting on your card, you can try to disable it.

D20 Blue Screen loading Windows 7-64bit using Intel controller and Marvell enabled

Hi, Help,
Hardware:
D20, 4158, Four 500GB Seagate SATA drives configured as a RAID10 1TB virtual disk (partitioned into five logical drives).
Goal:
Recover or repair a degraded RAID array.
I want to be able to launch Windows 7-64bit using the Intel controller and have it access the virtual disk of the degraded RAID array attached to the Marvell controller. Subsequently, I want to use the Marvell MRU utility to repair/recover the situation.
Situation/Issue:
Things ran well for two years and two months until yesterday. Now, when booting I see:
1962: No operating system found. Press F1 to repeat boot sequence.
If I use the Windows 7 installation CD and load the Marvell driver, the attempt to recover the operating system reports that the MBR is corrupt and cannot be repaired.
If I boot with the Marvell controller disabled in the D20 BIOS, using a Windows 7 installation (with Marvell drivers) attached to the Intel controller, everything works except (of course) I cannot access the RAID drives.
If I reboot with the Marvell controller enabled, using the same Windows 7 installation via Intel controller, I see a "Starting Windows" announcement followed by a flash of the blue screen of death.
The BSOD message is unspecific, no error code, just...
"A problem has been detected and Windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen,
restart your computer..."
Additional information:
If I access the Marvell BIOS (ctrl-M) and look at Devices, one of the four Seagate drives has status FREE instead of status ASSIGNED. If I run the Marvell BIOS verify disk utility diagnosic on that FREE status disk, I get a fault error after about 30 minutes of scanning. So, one Seagate disk is sour and somehow the MBR was corrupted at the same time.
History:
Two years ago, during the intial configuration, I could access the Marvell RAID disks from this Intel-controller-booted Windows 7 installation, but my fuzzy memory is that I had to change something in the D20 BIOS, such as the AHCI setting or similar.
Status:
Today, using the Intel controller to boot Windows 7 with the Marvell controller enabled is just BSOD. What am I missing or failing to do or set?
Thank you in advance for any help and ideas.
-John
Solved!
Go to Solution.

Update:
I replaced the 500GB Seagate disk with a new 500GB Seagate. I ran the Marvell BIOS verify disk utility on the new disk drive and it passed with no errors. Following the steps given in the Marvell MRU online help, I rebuilt the virtual disk. Upon completion (which took a little more than an hour to complete), I rebooted. Before the Seagate disk went south yesterday, the Marvell virtual disk contained one primary partition (C, and four NTFS drives (D:, E:, F:, and Z. Now it contains three primary NTFS drives (C:, F:, and Z. An extended partition contains D: (an unformatted volume of size 199.30MB) and an unused space of 199.30GB.
Event log:
Looking at the event log, Windows reports that the disk in question raised a warning yesterday. Three messages share the same timestamp (all from mv64xx (a Marvell process):
"Physical disk 16 is plugged out."
"Virtual disk 0 is degraded."
"Physical disk 16 is plugged in."
Eight seconds later, UserPnp logs:
"Driver Management has concluded the process to add Service disk for Device Instance ID SCSI\DISK&VEN_SEAGATE&PROD_ST3500418AS&REV_CC38\5&248BBE23&0&000100 with the following status: 0"
One second later, UserPnp logs:
"Driver Management concluded the process to install driver FileRepository\disk.inf_amd64_neutral_10ce25bbc5a9cc43\disk.inf for Device Instance ID SCSI\DISK&VEN_SEAGATE&PROD_ST3500418AS&REV_CC38\5&248BBE23&0&000100 with the following status: 0x0."
Questions:
Is it possible that UserPnp corrupted the Marvell virtual disk after an intermittent physical disk unplugged/plugged-in event that happened when the Seagate hardware went failed. It looks to me like my D: and E: are toast despite RAID 10.
Any ideas? Is there anyway to recover the Marvell virtual disk configuration to the state prior to the hardware failure? If not, what good is RAID 10?
My apologies for the long posting, but I am an old software guy who does not understand the intricacies of RAID and disk management.
Thank you in advance for any leads toward a solution,
-John

HI, I HAVE A MacBook Pro 2.3GHz dual-core Intel i5 AND I WAN'T TO UPGRADE THE HARD DRIVE UP TO 750GB AND ALSO THE RAM MEMORY TO 8GB. WHAT SPECIFIC MODEL OF HARD DRIVE AND RAM MEMORY SHOULD I BUY??? THANKS

HI, I HAVE A MacBook Pro 2.3GHz dual-core Intel i5 AND I WAN'T TO UPGRADE THE HARD DRIVE UP TO 750GB AND ALSO THE RAM MEMORY TO 8GB. WHAT SPECIFIC MODEL OF HARD DRIVE AND RAM MEMORY SHOULD I BUY??? THANKS

No need to type in all caps - we HEAR you!
I would take a look at the internal drives offered by both Crucial (click the link "Internal Hard Drives Now Available") and OWC. I would stay away from Western Digital drives as they seem to have problems on a number of Mac models.
You can also shop for RAM at Crucial and OWC - just select the System Scanner tab at the Crucial website to find out which memory is right for your machine.
Good luck,
Clinton

My itunes opens after 2-3 hrs after doubleclicking it to open;it happened once or twice with itunes 11.x , but its a constant problem after updating itunes to 12.x ....my operating system win7;processor i5 intel haswell and 4gb ram...i hav no issue

My itunes opens 2-3 hrs after doubleclicking it to open;it happened once or twice with itunes 11.x , but its a constant problem after updating itunes to the latest 12.0.1....my operating system windows7;processor i5 intel haswell and 4gb ram...i have no issue with opening other big programs....i tried uninstalling completely the itunes and reinstalling it as i thought at first it is not opening (because it takes really long time) and i followed the following support pages
1)iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
2)iTunes for Windows doesn't open after upgrading in Windows Vista, Windows 7, or Windows 8
but my problem doesnot get solved even after trying all the methods in the above pages...
now i realized,it opens after 2-3 hrs and at will...after opening it keeps hanging.finally it doesnot again open immediately after closing...kindly help me out as soon as possible

My itunes opens 2-3 hrs after doubleclicking it to open;it happened once or twice with itunes 11.x , but its a constant problem after updating itunes to the latest 12.0.1....my operating system windows7;processor i5 intel haswell and 4gb ram...i have no issue with opening other big programs....i tried uninstalling completely the itunes and reinstalling it as i thought at first it is not opening (because it takes really long time) and i followed the following support pages
1)iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
2)iTunes for Windows doesn't open after upgrading in Windows Vista, Windows 7, or Windows 8
but my problem doesnot get solved even after trying all the methods in the above pages...
now i realized,it opens after 2-3 hrs and at will...after opening it keeps hanging.finally it doesnot again open immediately after closing...kindly help me out as soon as possible

Intel WiDi and Miracast

I have an HP Pavillion g6-2010nr Notebook PC . It's came with Windows 7. I want to use a wireless display adapter to wirelessly display (mirror) my laptop screen on TV. It requires that my laptop be "Intel WiDi and Miracast" enabled. Is my laptop Intel WiDi and Miracast enabled? Do I have to install something? or can Windows 7 not do it? If Windows 7 can do it, how do I get it to connect? I know on Windows 8 there is a project option that allows you to connect to a TV, but I'm not sure where to find that option on Windows 7. I am a newbie, so the more details... the better.
Thanks
This question was solved.
View Solution.

Hi,
No. The following specs shows it does not meet WiDi requirements:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03377517
BUT if you wish, please use the following tool to confirm:
http://supportkb.intel.com/wireless/wireless-display/templates/selfservice/intelwidi/#portal/1026/ar...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Can I transfer docs between a MacBook with a Intel processor and a iMac with a PowerPC processor by using a usb cord?

Can I transfer docs/folders between a MacBook with a Intel processor and a iMAC with a PowerPC processor using a usb cord? Or by loading from the MacBook to a external drive and then to the Imac.

You need to use an external drive, FireWire cable, Ethernet cable, or wireless connection.
(73713)

Intel/PowerPC and Sharing ...

I just added an Intel Mac to my collection and I hooked my iMac to it to migrate and it didn't work.
When I came here to do research everywhere I click on Tiger Info including the top of this forum - Leopard comes up on screen.
Is Tiger Information still on the Apple Web Site? Everywhere I click to try and get it, Leopard Information comes up.
I'm trying to find Tiger Information as I just got an Intel Mac and need to find out how it will play with my PowerPC Macs. I also need to re-read sharing as I forgot how I set it up the 1st time to share files, printers aps etc ...
Can anyone point me to Tiger Overview etc ...?
Thanks

You don't use migration assistant to migrate files from a ppc to an intel. Check out this info:
http://discussions.apple.com/thread.jspa?threadID=435350&tstart=10

Intel 975x and E6600 overclocking?

I've attempted overclocking but I'm not sure if I'm doing it right.
E6600. 1GB RAM.
I've got my FSB @ 300 and set FSB & RAM at a 1:1 ratio. The RAM is now running at 533mhz as opposed to 667mhz.
My mobo is an Intel 975x and the RAM is DDR2 5300.
The only reason I'm asking is because I'm with stock cooling at 2.71Ghz and the test usually fails around 30 seconds with Orthos. So I'm stuck, Windows seems stable.
Anything you can guys can suggest?
Cheers.

Oh, in that case I think it's:
2x512MB Memory Speed 667 PC5400 timings manually set to 5,5,5,15
EDIT: Are the voltages and speeds I'm using safe? The memory voltage option at '2.0' was yellow so I was just wondering, I'm quite skeptical.
I've been running Orthos for about 20 minutes now and it seems to be running fine, of course it's not conclusive but the results are better than before.
I'm also wondering, If I were to upgrade my RAM what would be the best option for my setup? Like what timings and what speed RAM should I be looking for? Can I fit any speed DDR2 into this board?
EDIT2: Running Orthos, the cores are at 56C-55C respectively, is that an ok temperature?

Intel Galileo and Bluetooth(Master)

Hello Everyone,
How would you go about bluetooth usage on the Galileo? I bought an Intel 6235 and I also bought and arudino bluetooth shield. For the bluetooth shield It seems though if you want to use it as a master it does not work. Whenever I read from Serial or
Serial1 no data is returned but I should so something like "+OK" according to the HC05 documentation. I have the same code on arduino and it works fine but for the galileo it does not seem to work. Also is it possible to use the
windows bluetooth api with an ardunio bluetooth shield or it can only work with the Intel 6235.

Hi there,
The Bluetooth stack is not available in the Windows Developer Program for IoT Galileo image, so the traditional bluetooth APIs won't function.
Which Arduino shield are you using? There are many implementations of Bluetooth shields - some may not be compatible with the Galileo Hardware.
Thanks,
Lou

Intel Management and Security Status Icon started appearing 3 days ago

We didn't install anything new, and this "Intel Management and Security" icon (which you can't close) started appearing in the start menu on the bottom of the screen. What made this start appearing, and how can we get rid of it?

Hello aoppen,
please also refer to this guide how to use AMT.
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

Intel 7260 and Sattelite a665

Similar Messages

Maybe you are looking for