Interface Dot11Radio0, failed - cmd busy -Traceback.....
hi everyone,
please help me,
i have a problem with cisco autonomous:
Product/Model Number: AIR-AP1131AG-E-K9 System Software Filename: c1130-k9w7-tar.124-10b.JA System Software Version: 12.4(10b)JA Bootloader Version: 12.3(8)JEA
the problem is that my autonomous cisco AP sometimes crash and the only way to overcome this is to reset the AP...
i found the log --> "Interface Dot11Radio0, failed - cmd busy -Traceback= 0x5DBF8 0x4EDE70 0x4EDDD4 0x797684 0x7978E4 0x79BD64 0x4ECEC8 0x4ED2D0 0x4ED684 0x198850"
any comment on this problem....
please advice....
thanks
In enable mode, can you do a "dir flash:" and post the contents?
Do a "show ip interface brief" and make sure your radios are still up/up.
Similar Messages
-
Aironet 1310 Error Dot11Radio0, failed - cmd busy
Hello Kollegues!
I experience the following error and am courious if the radio has to be replaced? I could not find this error in the error reference so far. Thank you!
Critical Interface Dot11Radio0, failed - cmd busy -Traceback= 0x5DCB8 0x4EEC80 0x4EEBE4 0x793EE0 0x794140 0x7985C4 0x4EDCD8 0x4EE0E0 0x4EE494 0x198C10
Notification Line protocol on Interface Dot11Radio0, changed state to up
Error Interface Dot11Radio0, changed state to up
Warning Interface Dot11Radio0, Associated To AP YXZ-XYZ-BR01 001d.709a.feb0 [None]
Notification Line protocol on Interface Dot11Radio0, changed state to down
Notification Line protocol on Interface BVI1, changed state to up
Notification Line protocol on Interface FastEthernet0, changed state to up
Information Logging to host 10.10.0.10 started - CLI initiated
Notification Interface Dot11Radio0, changed state to reset
Notification SNMP agent on host XYZ-XYZ-BR02 is undergoing a cold start
Notification System restarted --
Attached the support information file.You've got "Traceback" error messages and your IOS version is classified as "Deferred Release". Try upgrading the IOS.
-
WiFi interface Dot11Radio0 fail to take encryption on 877W
Hi
I need to activate WiFi on a Cisco 877W with Advanced IP Services 12.4-15 T1 IOS. The moment I try to configure the encryption it gives me an error message :"No more than 0 encrypted VLANs can be configured for Dot11Radio0"... I removed the SSID config as well and reapplied the encryption on WiFi interface and got same results...Please assist. Different encryption options give the same results.
Site0030(config)#interface Dot11Radio0
Site0030(config-if)# no ip address
Site0030(config-if)#
Site0030(config-if)#encryption mode ciphers aes-ccm
No more than 0 encrypted VLANs can be configured for Dot11Radio0
Site0030(config-if)#Hello,
As per your query i can suggest you the following solution-
router# configure terminal
router(config)# interface dot11radio 0
router(config-if)# encryption vlan 22 key 3 size 128 12345678901234567890123456
transmit-key
router(config-ssid)# end
For more information please refer to the link-
http://www.cisco.com/en/US/docs/routers/access/1800/wireless/configuration/guide/s37wep.html
Hope this will help you. -
Problema Interface Dot11Radio0 is reset
Porfavor pido puedan ayudarme urgente, ya he configurado casí todas laas posibilidades y no encuentro el problema. sobre Dot11Radio0 is reset, line protocol is down
aaa new-model
aaa authentication fail-message ^CCCCCCCC!!!!!!!Fallo en login. Cinco fallas con
s
ecutivas revoca su usuario !!!!!!^C
aaa authentication login default group tacacs+ local
aaa authorization exec default group tacacs+ if-authenticated
aaa session-id common
dot11 ssid vlan9001
vlan 901
authentication open
infrastructure-ssid
username Cisco password 7 123A0C041104
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid vlan9001
antenna gain 10
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0
station-role non-root
infrastructure-client
interface Dot11Radio0.304
encapsulation dot1Q 304
no ip route-cache
no snmp trap link-status
bridge-group 2
bridge-group 2 spanning-disabled
interface Dot11Radio0.901
encapsulation dot1Q 901 native
no ip route-cache
no snmp trap link-status
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.304
encapsulation dot1Q 304
no ip route-cache
no snmp trap link-status
bridge-group 2
bridge-group 2 spanning-disabled
interface FastEthernet0.901
encapsulation dot1Q 901 native
no ip route-cache
no snmp trap link-status
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.41.74.193 255.255.255.0
no ip route-cache
ip default-gateway 10.41.74.254
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieeeConfiguraación del ROOT, pero el problema es el non-root.
dot11 ssid vlan9001
vlan 901
authentication open
infrastructure-ssid
username Cisco password 7 047802150C2E
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid vlan9001
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel least-congested 2412 2422 2462
station-role root
infrastructure-client
interface Dot11Radio0.304
encapsulation dot1Q 304
no ip route-cache
bridge-group 2
interface Dot11Radio0.901
encapsulation dot1Q 901 native
no ip route-cache
bridge-group 1
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.304
encapsulation dot1Q 304
no ip route-cache
bridge-group 2
interface FastEthernet0.901
encapsulation dot1Q 901 native
no ip route-cache
bridge-group 1
interface BVI1
ip address 10.41.74.194 255.255.255.0
no ip route-cache
ip default-gateway 10.41.74.254 -
Cisco AP1231G failed to flash the interface on failed boot
Hello,
I have an issue with Cisco AIR-AP1231G-E-K9 since I have rebooted it to reload startup conf :
Now, radio is disabled. On web interface, Radio mac address is 0000.0000.0000
I tried a no shut on Dot11radio0 but didn't work.
I tried to upload a new firmware but didn't solve the issue.
Here you can find result of sh log :
POZAPA-0004#sh log
Syslog logging: enabled (0 messages dropped, 3 messages rate-limited,
0 flushes, 0 overruns, xml disabled, filtering disabled)
Console logging: level debugging, 38 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 40 messages logged, xml disabled,
filtering disabled
Logging Exception size (4096 bytes)
Count and timestamp logging messages: disabled
Trap logging: level notifications, 34 message lines logged
Logging to 10.128.2.12, 34 message lines logged, xml disabled,
filtering disabled
Log Buffer (4096 bytes):
101.img)
*Mar 1 00:00:11.895: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:19.202: Failed to flash the interface on failed boot
*Mar 1 00:00:19.205: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:19.264: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:26.574: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:34.181: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:34.241: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-
k9w7-mx.123-7.JA3/5101.img)
*Mar 1 00:00:41.548: Failed to flash the interface on failed boot
*Mar 1 00:00:41.548: Tried to send command 0229 while the MAC not running
*Mar 1 00:00:41.549: Tried to send command 0229 while the MAC not running
*Mar 1 00:00:41.549: Unable to read RID_CHAN_POWER
*Mar 1 00:00:41.549: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available
*Mar 1 00:00:41.549: %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no valid power levels available
*Mar 1 00:00:43.640: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:43.642: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 01:00:43.768 GMT: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:43 UTC Fri Mar 1 2002 t
o 01:00:43 GMT Fri Mar 1 2002, configured from console by console.
*Mar 1 01:00:44.703 GMT: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 01:00:45.270 GMT: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 01:00:45.270 GMT: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(7)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 21-Mar-06 14:18 by ccai
*Mar 1 01:00:45.270 GMT: %SNMP-5-COLDSTART: SNMP agent on host POZAPA-0004 is undergoing a cold start
*Mar 1 01:00:45.286 GMT: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Mar 1 01:00:45.296 GMT: Writing radio coredump to 'flash:/r0_00_0000_E6177677.rcore'
*Mar 1 01:00:46.151 GMT: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
Sep 23 10:05:02.004 GMT: Writing radio coredump to 'flash:/r0_00_0000_BA624BBC.rcore'
Sep 23 10:05:05.015 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:05:06.073 GMT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Sep 23 10:05:38.648 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:05:38.708 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:06:12.048 GMT: Failed to flash the interface on failed boot
Sep 23 10:06:12.050 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:06:12.111 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:06:45.463 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:07:20.311 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:07:20.371 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c12
00-k9w7-mx.123-7.JA3/5101.img)
Sep 23 10:07:54.989 GMT: Failed to flash the interface on failed boot
As you can see , I have multiples line saying that radio is loading firmware but at the end we have "Failed to flash the interface on failed boot"
Did someone had this issue already ?
tanks for your answer.Sep 23 10:06:12.111 GMT: %DOT11-4-LOADING_RADIO: Interface Dot11Radio0, loading the radio firmware (flash:/c1200-k9w7-mx.123-7.JA3/5101.img)
This is the reason why your 802.11b radio won't come up. The radio-specific firmware is either missing or corrupted.
Most effective way is to overwrite and unpack the entire TAR file. So let the AP boot normally. Don't worry about the radio for the time being.
Make sure you have the TAR file located in the correct folder of your TFTP server. Use the command "archive download-sw /over /force tftp://<TFTP IP address>/filename.tar".
Once the process is complete the AP will reboot. -
Interface Dot11Radio0, cannot associate: No matching SSID
Hi all, I have a problem with a P2P Bridge with a couple of Aironet 1242AG.
Sometimes this Bridge goes down, and if I change Channel, it goes up.
When Bridge is down I can see this log in NoRoot:
*Apr 23 04:12:20.002: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP XXXX-Root 0014.1b60.9230 [None WPA PSK]
*Apr 23 04:12:20.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Apr 23 04:12:20.008: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: authenticate response status (12) denied
*Apr 23 04:12:20.069: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP XXXX-Root 0014.1b60.9230 [None WPA PSK]
*Apr 23 04:12:20.079: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not valid
*Apr 23 04:12:20.081: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Apr 23 04:12:31.049: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No matching SSID
*Apr 23 04:13:32.392: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from 0014.1b60.9230 channel 6 3669
*Apr 23 04:18:46.404: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Authenticating
*Apr 23 04:30:18.666: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP XXXX-Root 0014.1b60.9230 [None WPA PSK]
*Apr 23 04:30:18.666: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
I can see this log in Root:
7w4d: %DOT11-7-AUTH_FAILED: Station 001c.f663.1110 Authentication failed
7w4d: %DOT11-4-MAXRETRIES: Packet to client 001c.f663.1110 reached max retries, removing the client
7w4d: Client 001c.f663.1110 failed: reached maximum retries
7w4d: %DOT11-7-AUTH_FAILED: Station 001c.f663.1110 Authentication failed
I don't understand "No matching SSID" and authentication error, the Wpa-psk and Ssid are the same.
Do you have idea? I suppose a RF problem.
RegardsHi,
The "no matching SSID" appears when your non-root bridge tries to associate to a given SSID and does not detect any parent offering that SSID...
This seems to indicate (IMHO) a RF problem... you may want to try to monitor the link quality between your root and non root. If the signal is lots, then you would typically get this no matching SSID message while the non-root tries to reconnect without success.
Which code are you running on these APs?
Jerome -
Interface Dot11Radio0 cannot associate: No Response
Having an issue with a non-root bridge communication with the root device getting the error message -
*Mar 1 12:55:34.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
*Mar 1 12:55:46.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from 6cfa.8918.12e0 channel 3 3240
*Mar 1 12:57:01.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Authenticating
*Mar 1 13:02:59.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
I believe the issue may be down to the SSID but can't see what's wrong with the config any Ideas?
config of the WAP is -
Current configuration : 2074 bytes
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname UKPA
logging rate-limit console 9
enable secret 5 $1$y65O$Duk6tL2w8VxpeSkH9WIWu/
no aaa new-model
no ip cef
dot11 syslog
dot11 ssid BRIDGE
vlan 182
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 c942cc494622b70e126618c19eb768ee6fc8ded892204e7367b42384168f15c1
dot11 guest
username Cisco password 7 047802150C2E
bridge irb
interface Dot11Radio0
no ip address
encryption vlan 182 mode ciphers aes-ccm tkip
ssid BRIDGE
antenna gain 0
packet retries 64 drop-packet
station-role non-root
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0.182
encapsulation dot1Q 182
bridge-group 182
bridge-group 182 subscriber-loop-control
bridge-group 182 spanning-disabled
interface Dot11Radio1
no ip address
shutdown
antenna gain 0
peakdetect
no dfs band block
packet retries 64 drop-packet
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0.182
encapsulation dot1Q 182
bridge-group 182
bridge-group 182 spanning-disabled
no bridge-group 182 source-learning
interface GigabitEthernet1
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.182.22.11 255.255.128.0
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
ip default-gateway 10.182.1.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
endHi Paul,
Info: Point to remember is Non-Root Bridge to be connected to Root Bridge via native vlan SSID in order to carry multiple WLAN(or vlans) through this wireless bridge.
Try this:
interface Dot11Radio0.182
encapsulation dot1Q 182 native
bridge-group 1
interface GigabitEthernet0.182
encapsulation dot1Q 182 native
bridge-group 1
To know more, please check this:
https://rscciew.wordpress.com/2014/10/26/autonomous-ap-as-wireless-bridge/
Regards
Don't forget to rate helpful posts -
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
Hello,
On a 4402 wireless controller (7.0.220.0) with LAP1242AG-E-K9 and LAP1252AG-E-K9 access points I receive lots of messages like this:
Dec 9 12:55:16 ap-a1 1466: AP:001a.2f58.d4d6: *Dec 9 11:55:16.174: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
Dec 9 12:55:17 ap-a1 1467: AP:001a.2f58.d4d6: *Dec 9 11:55:16.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
what is a little bit annoying, in particular for voice communications.
Is there a way to get more information from any logs or is there a similar problem discussion anywhere on this forum?
Thanks.Hi Konstantin,
Unfortunately I do not think we have the radio status codes published, but I'll comment on them here:
Status 51: Reset on transmit completion. I'm not 100%, but I think this means the radio was supposed to reset (due to another reason) but had data to transmit, so it completed TX and then reset.
Status 52: Reset on completion of multicast packets. Similar to above, just with multicast traffic being queued up.
Status 37: Generic interface reset (up/down), often seen during bootup or on configuration changes.
Status 54: Radio interface was shutdown -- either configured by the user or perhaps part of the boot process.
Status 67: Reset after changing hostname on the AP. This also would occur on bootup once the config is loaded.
Status 71: Reset to update radio status on WLC. Also usually done upon AP joining the WLC after bootup.
-Pat -
Event Log: Interface Dot11Radio0, parent lost: Had to lower data rate
Hi,
AIR-AP1242
Firmware: 12.3(8)JEB
AP -> WGB mobil station
The event log from WGB have often this warning:
%DOT!!-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Had to lower data rate
Way?...
It is the first installation with this description.Is the client able to associate to the AP and transfer data. This error message genrally indicate a weak signal strength or a bad link. Move the client to a different location and check if that works.
-
VCS Connection Failed - 486 Busy Here
We create a conference in TMS - it adds the appropriate infrastructure, creates a conference ID, etc.
The first 2 people can dial into the conference without issue. Every additional person receives a busy tone.
When checking VCS - I see Conneciton Failed 486 Busy Here.
Has anyone seen this before?What do you have for bridge? Did you look at logs on the bridge to figure out why its doing - do you have more than 2 ports on your bridge?
-
PropertyNode: Interface Information: Interface Description fails on second call
Hello all,
I´m new here and I have a problem.
As the subject already tells the property node: Interface Information: Interface Description fails on second call.
I have written a SubVI to get the virtual COM Port of a specified Device, which is connected via USB to my computer.
Therefore I use the "VISA Find Resource" VI to get a list of all active COM Ports and then use the mentioned property Node to get the device information.
I search for a specific string in this device information and if this string is found, I have my needed COM Port.
This is all working. Except for the case I start this SubVI a second time.
I always get an error from this property node saying: Error: -1073807246 in Property Node, VISA: (Hex 0xBFFF0072) The resource is valid, but VISA can not currently access it.
I don`t understand why I´m getting this error. I don`t even open the VISA Resource. I just check the name of it and make a VISA Close.
Maybe the problem is in my device?! I don`t know.
If I switch my device off and on again. My VI is again working once.
I hope someone has an idea, where this problem comes from and how to fix it.
I have the part of my SubVI, which is relevant to see the issue.
Thanks in advice
Best regards
TDO
Attachments:
FindCOMPort .vi 20 KBHi TDO,
please indicate cross posts! (Even when this was 'just' the German forum…)
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome -
Interface getting failed after changing the Business system to that service
Hello All,
Our Env... is XI 3.0 and this is related to produciton env.
Based on our client requirment to change the business system from client 871 to 100 for one of the R3 system which is reciever type(rfc).
After doing all the necessary changes , that particular service is getting failed and in the CC monitoring for that service I can see the log as "RFC_ERROR_LOGIN_FAILURE" mandate 871 (earlier client) does not exist in the system.
The steps which I have followed to change the Business system.
1>I loged into the SLD of PRD system and clicked on businsess landscape .then i have clicked on the specified system to be changed (RY1 ) and then clicked on change mode and selected the required client (100) and saved the settings.
2>I have logged into ID(Integration Directory) and selected the service (RY1) which need to be changed .Under service -->Adaper specific -->compare sld configurations and then clicked on apply changes.
3>Now selected that communication channel of service (RY1) RFCRecieverR3 and changed the client 871 to 100 and the password of user XIRFCUSER ...
Then i saved the changes and after that i have activated that interface.
After that when i logged into CC monitoring and viewed that service channels and see the following errors:
Receiver channel 'RFCReceiverR3' for party '', service 'RY1'
Error can not instantiate RfcPool caused by:
com.sap.aii.af.rfc.RfcAdapterException: error initializing RfcClientPool:com.sap.aii.af.rfc.core.repository.RfcRepositoryException: can not connect to destination system due to: com.sap.mw.jco.JCO$Exception: (103) RFC_ERROR_LOGON_FAILURE: Mandante 871 não existente no sistema (selecionar mandante existente)
Can any one help me out of this situation , and i need to fix this ASAP as this is production system.
Awaiting for your reply.
Best Regards
Rakesh ReddyHello Nisar
Thanks for the update,
Let me say few points about this particular problem:
1>The interface "XX" from XI sends data to two systems( R3 -->RP1 & RY1), some thing like branched (same data is passed to both the reciever systems).
And the second RY1 is copy of First system RP1 (Production sys) which is used for data loading purpose and every week there will be a refresh from First sys (RP1) to Second(RY1).
2>Now the first sys(RP1) is recieving the data successfully from XI , and the second one (RY1) is getting failed .And this started after changing the Business system 871 to 100 .
3>As mentioned by you , I have checked all the points mentioned
i)In SM59 for XI (ABAP part) two rfc's are maintained (LCRSAPRFC & SAPSLDAPI) and the test connection is also fine...But I did not find these two connections in reciever systems(RP1 & RY1 too).
ii)In reciever system RY1 ,when i went to RZ70 , i did not noticed any special settings and SLD Bridge :Gateway Information is not maitained over there .and the same thing in other reciever system(RP1) , with this can we confirm that there is nothing wrong in RZ70 settings.
iii)In SLDAPICUST at recievers end for both systems nothing is mantained , where as in XI system all the details are maintained(Host name,port, user & password).
I have translated the error log into english from the CC monitoring for this interface which is in portuguese language .
It says that:
RFC_ERROR_LOGON_FAILURE: 871 Mandante not in the system (select principal existing)
Kindly advise me what to do ..for fixing this problem(this is pretty urgent and it is production env...)..
If any information required , I can provide that.
Best Regards
Rakesh Reddy -
Payables Open Interface Pgm fails without any error(Very urgent)
All,
I'm into an integration project where in I'm pushing Invoice doc from a third party appln to Oracle apps (11.5.10.2) thru payables open interface. The integration is smooth till today. We pushed a record today, but the concurrent neither picks up the data but failed with 'completed error' status. When I delete the same record from the interface, the concurrent runs fine. So we are sure there is some issue with the data in my record. Since concurrent is failed without any reason, from where I can get the log to know what is the actual problem with that record? Pls help me with your inputs.
Thanks,
SenSen,
To enable trace, please refer to this document (skip the part about generating TKPROF, just check the concurrent request output file if more details about the error are logged after enabling trace and setting the profile option).
Note: 453527.1 - How To Trace a Concurrent Request And Generate TKPROF File
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=453527.1
The database log file can be usually found under $ORACLE_HOME/admin/<SID>_<hostname>/bdump directory (or from SQL*Plus, issue "show parameter background_dump_dest").
Regards,
Hussein -
Index creation failed in Business Objects Explorer
Hi,
I installed the Business Objects Explorer ...
But I can not index anything.
When I try to index the following message appears:
"Server, DRWBI001.PolestarIndexing, generated messages The Following:
Index creation failed. File system Polestar exceptions occurred on the server. Search for Polestar ERROR Within the servers log file for more details. (Can not create directory C: \ Program Files \ Business Objects \ BusinessObjects Enterprise 12.0 \ win32_x86 \ \ Index \ DRWBI001.PolestarIndexing \ InProgress \ ExplorationIndexes \ 35e98114-4831-A254-8dad-497fd3d4bb26 \-30_10.09.41 2010-06. 564) "
What should I do? help me pleaseI do not have UNIVERSE.
I'm trying to index files like Microsoft excel.
I have to do some configuration in the CMC to be able to crawl in Business Objects Explorer?
What should I do to crawl in Business Objects Explorer? -
Service interface not listed in business system in ID.
Hi Experts,
In my QA system service interfaces are not listed in business system in ID, i have added product and SWCV in SLD and i am still unable to see the service interfaces of SWCV that i have added. i have done SLD and CPA cache refresh, restarted the QA system but still unable to resolve the issue.
Please suggest how to resolve this issue.Hi Venu,
i have done SLD and CPA cache refresh, restarted the QA system but still unable to resolve the issue.
Try if "Compare from SLD" works? This can be accessed by going to ID -> double-click business system -> communication component -> adapter specific identifiers
Regards,
Mark
Maybe you are looking for
-
JS: Using CS2 Scripts with CS3
We're getting ready to (finally) upgrade from InDesign CS2 to CS3. We use several scripts (Javascript) regularly. I know quite a bit changed with the object model in CS3. I've seen a couple of threads here where Olav mentions "script versioning" that
-
Movement Type & Excise Register
Hi Experts ! Is there any configuration between movement type & Excise Register, where do we define Excise Register's receipt / issue indicator for movement type I want to define movement type 161 in RG23A Part I Issue side, at present with the exist
-
Unable to access or view data with no authorization error
Hi Experts, Appreciate your guys help. I am ID administrator where by some of our user ID unable to view data/ display report for the some of data even the appropriate authorization already assigned to the user. However when we check in the transacti
-
Question about database structure - best practice
I want to create, display, and maintain a data table of loan rates. These rates will be for two loan categories - Conforming and Jumbo. They will be for two loan terms - 15year and 30year. Within each term, there will be a display of - points (0, 1,
-
ICE edit, in context editor not working?
I can't seem to activate the in context editor for the site newmovers.businesscatalyst.com. The 'Edit' button is there, and when I click it the link changes to /icecube but nothing else happens. I contacted BC's support team and was told "I suspect t