Intermittent loss of connection

For about a week now I have been suffering from a intermittent loss of connection to the internet the internet will be fine until it randomly decides to drop out. Usually I'll be surfing the website and go to navigate to another webpage when it times out and tells me it couldn't find the website in question. My games seems to be affected as well though it is more common for me to observe this in my browser the problem occurs in Firefox and I loaded Chrome as well one day and the problem appears there as well. I need some line quality tests with dslreports.com's line quality test and I did four of them they all reported intermittent packet loss the odd thing I noticed is in all four tests I did the same node suffered a varying amount of packet loss (ae-1-60.edge1.SanJose3.Level3.net) I have been trying to get some info on this server but I can't seem to find any info on it whatsoever I have included all four tests in the zip archive attached to this post.
I also did a fifth test which I included as well I did this test after resetting the router and did another test but it was much of the same. Please tell me how to troubleshoot this problem I am losing my mind and patience.
Line Quality Test 1
Line Quality Test 2
Line Quality Test 3
Line Quality Test 4
Line Quality Test 5

I've been having a simliar issue as well for about a month now where my internet drops out every now and then for several seconds and then comes back up. This only started happening after Hurricane Sandy in Staten Island, NY when my ONT had to be replaced after being flooded. Since then, I have already had my ONT replaced twice and was given a new REV I router and told to not send back my old REV D router which never had any problems before. I have even tried putting back the REV D router and I still kept losing internet every now and then. After multiple chats with Verizon, they seem to have pinpointed the problem to be a physical issue in my house. So, I tried connecting the REV I router directly to the ONT, via coax, and I still noticed the internet dropping. Looking at the router logs, I noticed the following entries every now and then (usually multiple times a day):
Jan 10 00:29:15 2013
System Log
WAN ETH
WAN Ethernet Link Up
Jan 10 00:29:14 2013
System Log
WAN Coax
WAN Coax Link Up
Jan 10 00:29:10 2013
System Log
WAN ETH
WAN Ethernet Link Down
Jan 10 00:29:10 2013
System Log
WAN Coax
WAN Coax Link Down
and
Jan 8 04:35:26 2013
System Log
WAN Coax
WAN Coax Link Up
Jan 8 04:35:26 2013
System Log
WAN ETH
WAN Ethernet Link Up
Jan 8 04:33:42 2013
System Log
WAN ETH
WAN Ethernet Link Down
Jan 8 04:33:41 2013
System Log
WAN Coax
WAN Coax Link Down
Looking at the advanced logs I ocassionally find the following entries associated with the link flapping:
2013/01/08 04:33:44.12 M mt_igmp_params_init:223: reconf: new lan interface: br0, ver 3
2013/01/08 04:33:44.12 M mt_igmp_params_init:235: reconf: new wan interface: eth1
2013/01/08 04:33:44.20 M clink1: link down, device will be down
2013/01/08 04:33:44.24 M lan if uninit br0
2013/01/08 04:33:44.24 M removing multicast group 224.0.0.1 from device br0 port 16
2013/01/08 04:33:44.24 M removing multicast group 224.0.0.1 from device br0 port 8
2013/01/08 04:33:44.24 M removing multicast group 224.0.0.1 from device br0 port 4
2013/01/08 04:33:44.24 M removing multicast group 224.0.0.1 from device br0 port 2
2013/01/08 04:33:44.24 M removing multicast group 224.0.0.1 from device br0 port 1
2013/01/08 04:33:44.24 M removing multicast group 224.0.0.1 from device br0 port 0
2013/01/08 04:33:44.24 M uninit igmp proxy module
2013/01/08 04:33:44.24 M init igmp proxy module
2013/01/08 04:33:44.24 M lan if init br0
2013/01/08 04:33:44.24 M adding multicast group 224.0.0.1 to device br0 port 0
2013/01/08 04:33:44.24 M adding multicast group 224.0.0.1 to device br0 port 1
2013/01/08 04:33:44.24 M adding multicast group 224.0.0.1 to device br0 port 2
2013/01/08 04:33:44.24 M adding multicast group 224.0.0.1 to device br0 port 4
2013/01/08 04:33:44.24 M adding multicast group 224.0.0.1 to device br0 port 8
2013/01/08 04:33:44.24 M adding multicast group 224.0.0.1 to device br0 port 16
2013/01/08 04:33:44.31 M jan  8 04:33:43 syslog: check_exit: exiting
2013/01/08 04:33:45.10 M igmprx_lan_port_add_single: ifname=br0  ifindex=9
2013/01/08 04:33:45.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:45.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:45.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:45.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:45.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:45.10 M @@ setting new value completed, it should show new value in proc/proxy
2013/01/08 04:33:45.12 M mt_igmp_params_init:223: reconf: new lan interface: br0, ver 3
2013/01/08 04:33:45.20 M eth1: link down, device will be down
2013/01/08 04:33:45.26 M lan if uninit br0
2013/01/08 04:33:45.28 M removing multicast group 224.0.0.1 from device br0 port 16
2013/01/08 04:33:45.28 M removing multicast group 224.0.0.1 from device br0 port 8
2013/01/08 04:33:45.28 M removing multicast group 224.0.0.1 from device br0 port 4
2013/01/08 04:33:45.28 M removing multicast group 224.0.0.1 from device br0 port 2
2013/01/08 04:33:45.28 M removing multicast group 224.0.0.1 from device br0 port 1
2013/01/08 04:33:45.28 M removing multicast group 224.0.0.1 from device br0 port 0
2013/01/08 04:33:45.28 M uninit igmp proxy module
2013/01/08 04:33:45.28 M init igmp proxy module
2013/01/08 04:33:45.28 M lan if init br0
2013/01/08 04:33:45.28 M adding multicast group 224.0.0.1 to device br0 port 0
2013/01/08 04:33:45.28 M adding multicast group 224.0.0.1 to device br0 port 1
2013/01/08 04:33:45.28 M adding multicast group 224.0.0.1 to device br0 port 2
2013/01/08 04:33:45.28 M adding multicast group 224.0.0.1 to device br0 port 4
2013/01/08 04:33:45.28 M adding multicast group 224.0.0.1 to device br0 port 8
2013/01/08 04:33:45.28 M adding multicast group 224.0.0.1 to device br0 port 16
2013/01/08 04:33:46.10 M igmprx_lan_port_add_single: ifname=br0  ifindex=9
2013/01/08 04:33:46.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:46.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:46.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:46.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:46.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:33:46.10 M eth1: stopped
2013/01/08 04:33:46.10 M eth1: mac address changed
2013/01/08 04:33:46.10 M port 0: setting mac to 0x1, status: 0x2c3d
2013/01/08 04:33:46.10 M eth1: link up
2013/01/08 04:33:46.10 M eth1: started
2013/01/08 04:35:27.24 M eth1: link up, device will be up
2013/01/08 04:35:27.54 M clink1: lof 1000mhz
2013/01/08 04:35:27.55 M mt_igmp_params_init:223: reconf: new lan interface: br0, ver 3
2013/01/08 04:35:27.63 M clink1: link up, device will be up
2013/01/08 04:35:27.63 M lan if uninit br0
2013/01/08 04:35:27.63 M removing multicast group 224.0.0.1 from device br0 port 16
2013/01/08 04:35:27.63 M removing multicast group 224.0.0.1 from device br0 port 8
2013/01/08 04:35:27.63 M removing multicast group 224.0.0.1 from device br0 port 4
2013/01/08 04:35:27.63 M removing multicast group 224.0.0.1 from device br0 port 2
2013/01/08 04:35:27.63 M removing multicast group 224.0.0.1 from device br0 port 1
2013/01/08 04:35:27.63 M removing multicast group 224.0.0.1 from device br0 port 0
2013/01/08 04:35:27.63 M uninit igmp proxy module
2013/01/08 04:35:27.63 M init igmp proxy module
2013/01/08 04:35:27.63 M lan if init br0
2013/01/08 04:35:27.63 M adding multicast group 224.0.0.1 to device br0 port 0
2013/01/08 04:35:27.63 M adding multicast group 224.0.0.1 to device br0 port 1
2013/01/08 04:35:27.63 M adding multicast group 224.0.0.1 to device br0 port 2
2013/01/08 04:35:27.63 M adding multicast group 224.0.0.1 to device br0 port 4
2013/01/08 04:35:27.63 M adding multicast group 224.0.0.1 to device br0 port 8
2013/01/08 04:35:27.63 M adding multicast group 224.0.0.1 to device br0 port 16
2013/01/08 04:35:28.10 M igmprx_lan_port_add_single: ifname=br0  ifindex=9
2013/01/08 04:35:28.10 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:28.12 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:28.12 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:28.12 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:28.12 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:36.79 M mt_igmp_params_init:223: reconf: new lan interface: br0, ver 3
2013/01/08 04:35:36.79 M mt_igmp_params_init:235: reconf: new wan interface: eth1
2013/01/08 04:35:36.85 M dhcp client: wan ethernet renew ip address: 173.56.37.223
2013/01/08 04:35:36.85 M dhcp client: wan ethernet renew netmask: 255.255.255.0
2013/01/08 04:35:36.85 M dhcp client: wan ethernet renew gateway: 173.56.37.1
2013/01/08 04:35:36.85 M dhcp client: wan ethernet renew dns server: 208.67.222.222 208.67.220.220
2013/01/08 04:35:36.90 M lan if uninit br0
2013/01/08 04:35:36.90 M removing multicast group 224.0.0.1 from device br0 port 16
2013/01/08 04:35:36.90 M removing multicast group 224.0.0.1 from device br0 port 8
2013/01/08 04:35:36.90 M removing multicast group 224.0.0.1 from device br0 port 4
2013/01/08 04:35:36.90 M removing multicast group 224.0.0.1 from device br0 port 2
2013/01/08 04:35:36.90 M removing multicast group 224.0.0.1 from device br0 port 1
2013/01/08 04:35:36.90 M removing multicast group 224.0.0.1 from device br0 port 0
2013/01/08 04:35:36.90 M uninit igmp proxy module
2013/01/08 04:35:36.90 M init igmp proxy module
2013/01/08 04:35:36.90 M lan if init br0
2013/01/08 04:35:36.90 M adding multicast group 224.0.0.1 to device br0 port 0
2013/01/08 04:35:36.90 M adding multicast group 224.0.0.1 to device br0 port 1
2013/01/08 04:35:36.90 M adding multicast group 224.0.0.1 to device br0 port 2
2013/01/08 04:35:36.91 M adding multicast group 224.0.0.1 to device br0 port 4
2013/01/08 04:35:36.91 M adding multicast group 224.0.0.1 to device br0 port 8
2013/01/08 04:35:36.91 M adding multicast group 224.0.0.1 to device br0 port 16
2013/01/08 04:35:36.91 M out: [62] nat error: no free nat ip ([62] nat error: no free nat ip: )
2013/01/08 04:35:37.19 M igmprx_lan_port_add_single: ifname=br0  ifindex=9
2013/01/08 04:35:37.19 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:37.19 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:37.19 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:37.19 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:37.19 M igmprx_lan_port_add_single: ifname=eth0  ifindex=2
2013/01/08 04:35:37.19 M @@ setting new value completed, it should show new value in proc/proxy
2013/01/08 04:35:47.83 M acs ack: event = 4 value change
I setup syslog on the router which feeds it to the WallWatcher application and this is all the details I get duing the flap. I'm really stumped by this and can't figure out what the problem is. Could it be a bad PON card? I noticed that the logs show only the WAN Coax going down without the LAN Coax which leads me to believe in a faulty connection between the router and the ONT. I've already tried connecting both routers directly to the ONT to no avail. The only changes that I can think of since Sandy are the electrical outlets that were replaced. Could they be causing some kind of interference? I've tried running the coax with and without the ground block, but that didn't help either. The only thing that was not replaced since the first post-Sandy installation is the ONT battery system, only the battery itself was replaced once. Could that be it? Just to be clear, I have always been connected via coax and I have tried testing with different cables.

Similar Messages

  • WLC 5508 intermittent loss of connectivity

    Hi.
    I have a WLC 5508 connecting directly to a distribution switch (3850) via a layer 2 etherchannel trunk fibre link with LAG enabled on the WLC.
    Whenever there is a loss of power to the server room where both devices are hosted & power later gets restored, the distribution switch & WLC lose Layer 2 & 3 connectivity. Connectivity only gets restored when the WLC is power cycled or the fibre cables connecting to its SFP ports are removed & plugged back in. When this is done connectivity is restored between them, APs associate etc. Once there is a loss of power to the room for whatsoever reason again, the loss of connectivity issue re-occurs.
    Disabled the etherchannel at some point, using only a single fibre trunk link between them, but the issue persists.
    Also check for interface errors, CRCs, etc on both ends but there are none.
    Can anyone please advice me on what the issue is & what can be done to permanently resolve this?
    Thanks in anticipation.
    Ope.

    Software version is 7.4.100.0
    int gig1/0/5
      switchport mode trunk
      switchport trunk encapsulation dot1q
      channel-group 1 mode on
    int gig1/0/6
    switchport mode trunk
    switchport trunk encapsulation dot1q
    channel-group 1 mode on
    Port setting on the switch is set to auto-negotiate. Port setting on the controller is "auto". The link has been negotiated (& always negotiates) to 1000Mbps full duplex on both ends.
    Presently in transit with no way of connecting to the device, but I checked the duplex & speed settings on both devices which was appropriately negotiated. Also checked for interface error counters on the switch, there was none. Checked the WLC logs too, there were no logs on issues with the interfaces or auto-negotiation.

  • V04 and intermittent loss of connection whilst usi...

    In 3+ years with BT Vision I have had perhaps two V04 errors which were fixed with suggested re-boot.
    In the last week I have had more than 10 and reboots don't fix the errors permanently. I get connection back but then get errors later or find the Vision services are not available. Watching film last week, the connection dropped about 10 times during the film.
    I have run the Speedtest but have found the instructions and posted results to be totally inconsistent with the results I was getting.
    For example, after performing Speedtest it asks what Connection Rate & IP Profile results I get - Speedtest doesn't give you these results, it gives download speed (Mbps), Upload speed (Mbps) & Ping Latency.
    By clicking other options it then takes me to api.home site. This shows Bandwidth rate differently.
    Mine was:
    Bandwidth
    448 / 8,128
    However it then asks you to select if you are getting 'Connection Rate of more than 2016' or 'Connection Rate of less than 2016'. Which ever option you chose, it states: "It looks like your broadband connection is causing problems with your BT Vision On Demand service".
    Then it asks you questions about microfilters and then finishes, so was of no use to me.
    As my error is intermittent (but frequent) I am unclear how to progress this.

    I suggest a phone call to the Vision Team. it may indeed be a problem with your BB speed.
    Life | 1967 Plus Radio | 1000 Classical Hits | Kafka's World
    Someone Solved Your Question?
    Please let other members know by clicking on ’Mark as Accepted Solution’
    Helpful Post?
    If a post has been helpful, say thanks by clicking the ratings star.

  • Intermittent loss of internet connection on Homehu...

    Hi Everyone
    I have recently taken out a new contract with BT and connected my new Homehub 4 on the 14th February.  Seemly it was okay for at least 5 days then I started to experience some intermittent loss of internet on all of the devices, i.e PC, laptop, xbox, it effected both wired and wireless.  The hub was showing orange light, which then prompt me to press the reset/restart button on top of the hub.
    I have try out my old Homehub 1 for 3 days to see if it effected that one too, but the hub 1 was perfect in term of no loss of connection for 3 day.
    Then I connect homehub 4 again on Fri 28th February it was okay for a day, except on 1st march in the morning hub seem to disconnect/reconnect itself. Then around 2310 pm I have loss all connection to the internet through all of my devices again.
    Does anyone know what this problem is?  It is to do with BT-Wifi Fon, or is the hub 4 faulty and need replacing?
    Many Thanks

    It was orange central broadband light, there were no other light showing on the silver part.
    I have not tried test socket yet, however, I did have a new master socket and line replaced couple year ago, so it would have the new faceplate on there. Plus, the external line etc must be working since hub 1 was working perfectly.
    Here the information from speed test
    Download  Speed:        1.98 Mbps
    0 Mbps 2 Mbps
    Max Achievable Speed
     Download speed achieved during the test was - 1.98 Mbps
     For your connection, the acceptable range of speeds  is 0.4 Mbps-2 Mbps.
     Additional Information:
     Your DSL Connection Rate :2.3 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 2 Mbps
    23:17:22, 01 Mar.           ( 86.310000) DSL noise margin: 17.00 dB upstream, 10.20 dB downstream
    23:17:22, 01 Mar.           ( 86.130000) DSL line rate: 448 Kbps upstream, 2304 Kbps downstream
    Any idea what this mean on the event log? I seem to keep getting PPP LCP send conf request.
    23:17:26, 01 Mar.           ( 89.940000) PPP LCP Send Configuration Request
    23:17:15, 01 Mar.           ( 78.760000) CWMP: session closed due to error: Could not resolve host

  • Intermittent Loss of Audio

    I rented Micheal Clayton on HD a couple of days ago (my second HD rental), noticed that the movie playback had intermittent loss of audio whether I set it to DD5.1 or not it made no difference.
    The audio loss don't seem to happen at the same scene everytime I rewind and play it back all over again. It seems to happen at random scenes during the movie playback and several times there was no audio for nearly 5 to 10 seconds before it reappears and when I rewind and playback the same scene again, the audio seems to be alright for most parts?
    I am wondering if any other users have had similar audio issues with rented movies from iTunes?
    This is like my first rental movie which had issues with audio, the previous 3 or 4 rentals did not have any audio nor video issues. It's not my ATV unit either because movies and music videos which I already own, playback on it just fine in DD5.1 via Optical and HDMI. So the issue was just with that one movie which I rented then.
    I am wondering how could one demand for a refund from Apple when faced with such problems or issues after the rented movie dissappears from your ATV 24 hours later??
    Now I am feeling cautious to rent another movie, what if I have another issue with which ruins the movie experience?
    I think I will stick with my PS3 and Blu-Ray for now.

    Not sure but I thought I read in another issue that if you connect a TB cable from your Mini into the TB port on the display and the audio/video is OK then that would mean the built-in cable is bad.  I have never tried this so not sure it would work.  Hate to buy a TB cable just to  test because of cost.  The other way would be to take to Apple store and have them check the cable.  It contains miniture IC boards and one could be bad.

  • Intermittent Loss of Communications with Solaris 10

    With a 32 port Terminal Server, if greater than 28 ports are connected to
    active hardwired patient monitoring devices, our application on
    Solaris 10 experiences intermittent Loss of Comms one port (which a patient device is connect to) at a time. This happens whether or not other terminal servers are attached and has nothing to do with total device load load. We have been able to sustain device loads greater than 60 patients with NO comms loss as long as the 32 port Terminal Server(s) has 28 ACTIVE PORTS OR LESS.
    The Loss of Comms ONLY occurs for devices connected to the 32 port
    Terminal Server with greater than 28 ports connected to active devices.
    This does not occur with Solaris 8. It only occurs with Solaris 10
    11//06.
    Is this a TCP/IP configuration issue?
    I've begun trying to use DTRACE with Provider "mib", but need to narrow
    down the "filtering" to only trace on exactly what is needed to get to the root of this issue.
    Anyone have any ideas?

    I had the same problem. I tried all the obvious stuff (reset etc) and tried some of the random fixes suggested on here.
    Have you tried cleaning all the gunk from the charger port? Mine was clogged with pocket fluff so I got in about it with a tooth pick - problem solved!
    Good luck  :)

  • MacBook Air intermittently has issues connecting to websites when wireless shows connected to the internet. The pages show that I am offline, but I can ping Google DNS. Windows PC, iPhone and Android phone have no issue displaying the same web pages.

    MacBook Air intermittently has issues connecting to websites when wireless shows connected to the internet. The pages show that I am offline, but I can ping Google DNS. Windows PC, iPhone and Android phone have no issue displaying the same web pages.How do I solve this issue?

    Go step by step and test.
    1. Power off the router. Unplug it from the wall. Wait a while.
        Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
        Restart the computer.
        Start up in Safe Mode.
        http://support.apple.com/kb/PH14204
    2. Empty Caches
        Safari > Preference > Advanced
        Checkmark the box for "Show Develop menu in menu bar".
        Develop menu will appear in the Safari menu bar.
        Click Develop and select "Empty Caches" from the dropdown.
    3. Deselect Proxies if selected.
        System Preference > Network > Advanced  > Proxies Tab
        Under "Select Protocol", uncheck any box if selected.
        Click "OK" then  "Apply”.

  • HT1222 Ipad2 losses cell connection now that iOS 8 was installed.  Ios 8.0.2 did NOT correct the issue. Come on and fix this issue!

    Ipad2 losses cell connection now that iOS 8 was installed.  Ios 8.0.2 did NOT correct the issue. Come on and fix this issue!

    Hey everyone-
    Im in the same boat, started a thread . My hands free system worked fine with iOS 8 out of the box new iphone 6. Did the update this morning and i can stream music perfectly fine however i cannot make or receive calls through hands free system.
    I have not tried resetting the settings like most people indicate is working. I feel like I shouldn't have to reset anything, even less mess with settings with an update coming from apple. it should "Just Work"
    Some people who reset said it works for a few hours, other say it don't work, and I don't know what I should do.
    Car: Hyundai Sonata 2014
    NOTE: I was able to replicate the issue in my wifes Hyunday Elentra 2013.
    This is how I know its not a defect with the BT in my car.

  • Sensing a loss of connection without explicitly sending a message

    First I need to know if I am even on the right forum since I don't have a clue whether the Sun Java System Message Queue and the Sun ONE Message Queue, v3.0.1 are the same animal. Since there was no forum for the Sun ONE Message Queue I'm assuming they are one and the same. If not let me know.
    We are attempting to sense a loss of connection to the JMQ broker by attempting to create a session against an already established Connection object. The theory is that createSession will fail if the connection is down but it doesn't seem to be working. We don't want to have to explicitly send a message on the down connection to trigger an exception but if we absolutely have to we will. We are periodically checking the status of many connections and would prefer to not spend too much time at it. I also considered using Connection.start() to see if perhaps "re-starting" an established connection would generate an exception if the connection is down. If anyone knows how the pros at SUN do this, I would appreciate the knowledge very much.

    Hi, did you get a proper answer to your question? We're also trying to detect loss of connection on the client side: shall we have to use the session creation or is there a way to sense the loss of the connection as soon as it happens? We've tried setting an exception listener on the connection, but that didn't help.
    Thanks.

  • InDesign CC keeps crashing after reporting loss of connection

    Hi Everyone,
    I am working over a local network and when i create an indesign file (or work on an existing one), InDesign reports a loss of connection (or an other process changing the file) and crashes. This happens after a very short time, between 1-5 minutes after opening a file.
    It makes me unable to finish any job! Please do not tell me to work local, because thats not the solution for me.
    The internet connection is stable and has no delay. I work in Windows 7, InDesign CC.
    I reset the preferences already, changed the location for automatic saves... nothing
    Thanks,
    Nora

    Hi Yeonala,
    As mentioned by Peter correctly, your LAN connection maybe one of the reasons for this behavior.
    Beacuse when InDesign try to Edit Or Save remote document in disconnected state, it shutdowns as protective measure.
    However, can you please provide more detail about "changed the location of automatic saves" ?
    Thanks
    -Sumit

  • Intermittant loss of sound

    since i updated the software on my iphone 4 i have intermittant loss of sound i have researched and this is a common problem trouble is no one has an easy fix answer the best suggestion is to revert the phone back to the old software but i have no idea how to do this and apple dont seem to be acknowleging that they messed up with the update so if anyone can help i would be very gratefull
    many thanks

    I have been there and done that.....makes no difference. Why do you think that the all of a sudden it would change the output in the first place? Things don't change by themselves for no apparent reason. It was still on the bose speakers when I went into sys pref. Amazing that you think that it would change itself everyday....did you really read my post or were you distracted?

  • HT4199 this still didn't fix iPad connectivity after updating to iOS 6.0.1 !!! intermittent wi-fi connection, even with a direct line-of-sight to the router.

    "HT4199: iOS and OS X: Recommended settings for Wi-Fi routers and access points"
    this still didn't fix iPad connectivity after updating to iOS 6.0.1 !!! intermittent wi-fi connection, even with a direct line-of-sight to the router.

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • TS3048 my magic mouse losses the connection and then reconnects, battery level is ok. Can anyone help? thanks

    Hi,
    My magic mouse has started to intermittently loose the connection to my Imac. can anyone advise what the problem may be. Thanks

    Hi,
    I have also changed the mouse, but had read that the problem was the batteries not connecting properly. I think I have now solved it. The new mouse was fine until I changed the batteries. I put Duracell in, but it seems they are a fraction shorter than those supplied (Energizer). I got some Energizer batteries and hey presto - problem gone.
    David.

  • Loss of connection

    Today i lost connection to the internet, the broadband light was flashing orange. I reset the Modem and the Hub and the Hub broadband light returned to blue. But my desktop pc had a big red cross in the bottom right hand corner over the network icon. I had disconnected the ethernet cables in the back of the hub, but they were all connected properly. When i looked at the back of my pc the end on the connection end did seem a little dodgy. So i recrimped a new end on and that did appear to sort it. But on the desktop i cannot open hardly any web pages they are so slow, i can't do any speed tests as i get timed out out. 
    I have hooked up my laptop using the same ethernet cable and everything is perfect, speeds test are all as they should be.
    It seems the issue lies with my desktop pc, but everything was working perfectly ok before the loss of connection, i have tried severeal browsers and none of them seem to want to respond very well at all.  
    Has anybody got any suggestions or solutions please???

    Hi Damian99,
    Thanks for posting. It sounds like the problem could be with your PC as it’s connecting via the laptop. Has anything changed since the connection dropped? Have you checked the Ethernet socket as opposed to the cable? Let us know how you get on.
    Cheers
    David
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • Mail app intermittently fails to connect - internet accounts preferences cannot connect, then unable to verify name or password. Why?

    Running 10.10.2 on early 2011 MBP, 8 GB RAM.
    Mail app intermittently fails to connect - message: internet accounts preferences cannot connect, then unable to verify name or password.  No problem with iPhone to connect same 3 accounts. Have run Disk Utility and rebooted. What is happening?

    Same issue, too.  But I have nothing better to do than try to fix Apple problems that appear mysteriously and randomly; I'm sure you're the same way.
    The REAL REASON, which can no longer be overlooked, is that Apple's (probably underpaid sweatshop Chinese) employees build toys for grown-ups and do little more than that.  I wish I had never bought my Mac (2009) since few things about Apples are "intuitive" unless you've been an Apple cultist since Jobs introduced the first Mac.  Oh, and because things mysteriously stop working, something I don't recall happening with any of the PCs I've owned. 
    Apple's version of Excel is a total joke and on an update that I did not ask for, the "Save As" feature, a convention that was 30 years old and worked well, was removed in favor of "Duplicate, Rename, Save."  What 22 year-old Apple product manager was allowed to make this change? 
    I foolishly compounded my Mac purchase error by buying an iPhone 4S.  On that lovely ($200 Verizon-subsidized) product, I can no longer discover my home network, rendering my ($100) Airplay for outdoor music useless.  (But I probably can post a picture directly to Facebook or something!  More toyish behavior in which Apple specializes.)  Can I get support on these POS with a phone call?  No, I need to rely on a Aapl cultist to devise some esoteric key combo or a "jailbreak" on a Support board or blog site.
    I'm eligible for a phone upgrade on 8/13 and I'm counting the days.  Will upgrade to a good large-screen laptop asap as well and then throw the Mac out my office window.  Junk, just junk.  Apple's stock is at $433 from $700 and it's still overpriced.  How long will this rant last before it's sanitized by the Cupertino Big Brother? Maybe what the children who design product ought to do instead is BUILD BETTER STUFF.

Maybe you are looking for

  • Need to Disable a link when a condition is failed in Web dynpro ABAP

    HI Gurus,   I have an requirement, I am displaying one form, above the form I am displaying the link as  Overview. if some conditions failed and the form is not displayed, I want to disable that link ' OVERVIEW" should be in disable mode. Please prov

  • Error to PACKAGE BODY WWSSO_AUTH_EXTERNAL

    hi to all, i followed the paper 'Configuring Oracle9iAS Portal for LDAP Authentication' in order to redirect authentication Login Server to OID. After all steps i have to run ssoldap.sql from sqlplus. Firstly, i got this errors (when the sql file cal

  • ADF Faces & BC: Best pratices for project layout

    Season greetings my fellow JDevelopers! Our software group has been working with ADF for around 5 years and through the years we have accumulated a good amount of knowledge working with JDeveloper and ADF. Much of our current application structure ha

  • HT1212 im getting a 3194 errror code. what do i need to do?

    How do i set up a meeting with apple to fix my ipod. it is locked out and my itunes wont work on my computer.

  • Validation in input template

    I need a validation message that when user send the invalid charectore as value to database invalid charectors thru send function a warning message is given that invalid values such as 'ABCD' charecter cannot be send. Currently when invalid charecter