Inventory scanning is successful, but performance gathering is not.
I am running the MAP tool in my environment. I am able to successfully connect to all of my Windows servers and see the WMI information about their processors, memory, OS version, IP address, etc. When I run a 30 minute performance gathering test on them,
only 12 of the 28 or so servers I'm scanning are reporting information. The rest of the servers aren't even appearing in the list of clients in the "CollectionStatistics" tab of the results spreadsheet.
The 16 failing servers are successful in reporting their inventories, though, so I know WMI is enabled and the credentials I provided are correct.
Troubleshooting procedures I've done:
- pinged the server by name and IP successfully
- Opened computer management (compmgmt.msc) and used the "connect to remote computer" option. While connected I verified that Remote Registry is started and running.
- Successfully established Telnet connections to the servers failing to report performance metrics on port 445 and 139.
- used wbemtest to successfully establish a connection to the remote servers. I was able to run the query "select * from win32_useraccount" and observe results returned.
At this stage I'm not sure what other tests to perform for troubleshooting. Has anyone else encountered this problem or have any advice as to how I can get these non reporting servers to start dumping performance data?
The performance data collector requires remote registry to be enabled. See this TechNet Wiki article for more information:
http://social.technet.microsoft.com/wiki/contents/articles/12163.map-prepare-the-environment-remote-registry-service.aspx
Please remember to click "Mark as Answer" on the post that helps you, and to click
"Unmark as Answer" if a marked post does not actually answer your question. Please
VOTE as HELPFUL if the post helps you. This can be beneficial to other community members reading the thread.
Similar Messages
-
I’ve tried to update my i-Tunes version after the site suggested I should following my i-Pad Air being plugged into it for the first time. The update seemed successful but the program would not open at all despite switching off the PC and re-starting several times. I then tried wiping the original software from the computer and re-downloading from scratch. Each time I tried the download failed with a message saying “Service “Apple Mobile Device” failed to start. Verify that you have sufficient privileges to start system services” At this stage, the only way forward was to “abort” the download. This I have done now four times and the same thing happens. When I did finally manage to get an i-Tunes shortcut on my desktop, the program wouldn’t open saying: “i-Tunes was not installed correctly. Please re-install i-Tunes. Error 7 (Windows error 193)” Any ideas to resolve this?
Try the following user tip:
Troubleshooting issues with iTunes for Windows updates -
Root device mounted successfully, but /sbin/init does not exist ???
I'm having the issue where when I boot after doing a fresh install, it gives me:
ERROR: Root device mounted successfully, but /sbin/init does not exist
Bailing out, you are on your own. Good luck
sh: can't access tty; job control turned off
[rootfs /]#
My fstab:
# /etc/fstab
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda1 LABEL=homerroot
UUID=877deab9-624d-4e1d-90a1-ccc1d6ebc0c6 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda2 LABEL=homerboot
UUID=77835da5-8a38-44c1-bf27-bb657df4484b /boot ext4 rw,relatime,data=ordered 0 2
# /dev/sda3 LABEL=homeretc
UUID=8a1b5bd8-b147-41e0-87df-70a4a9e12df2 /etc ext4 rw,relatime,data=ordered 0 2
# /dev/sda4 LABEL=homervar
UUID=8eb2e7b1-cdf1-46ce-9dc1-439d002bfae4 /var ext4 rw,relatime,data=ordered 0 2
# /dev/sda5 LABEL=homerusr
UUID=bce162b4-d27f-450c-a0e6-4d3ebc6242dc /usr ext4 rw,relatime,data=ordered 0 2
# /dev/sda6 LABEL=home
UUID=62de76ab-b6d4-4e3d-a423-c287b81813a9 /home ext4 rw,relatime,data=ordered 0 2
# /dev/sda7 LABEL=public
UUID=d98a9c8e-2301-4e66-8c7f-26167633a4b0 /public ext4 rw,relatime,data=ordered 0 2
This looks fine to me, but when /dev/sda1 is mounted at /new_root, none of the other devices are mounted....
I don't know if this is what's causing the problem since /etc, and /usr are on separate partitions from root, but
this would be the first time I get a problem dividing things this way (on ubuntu, mint, fedora, et cetera).
So I tried:
https://bbs.archlinux.org/viewtopic.php … 3#p1283343
I get "* is owned by filesystem 2013.05-2" for all three dirs from step three.
None of the other steps have any effect....
I also tried:
https://bbs.archlinux.org/viewtopic.php?id=172943
My /dev/sda1 mounts to new_root, so I don't think I'm having his problem.
And:
https://bbs.archlinux.org/viewtopic.php?id=166423
I reinstalled systemd-sysvcompat, and I'm sure that's not my problem.
Interestingly enough, /usr/lib/systemd/systemd is an elf file on my target hard disk.
Is this an outdated issue or something? Or should /usr/lib/systemd/systemd be a text file?
Thanks in advance for your help guys!WorMzy wrote:Oh, and /usr/lib/systemd/systemd is supposed to be an ELF binary. Not sure why you think it should be a text file.
I saw another thread saying that adding an entry there would help. I think it was "init=<something>".
WonderWoofy wrote:A separate /etc is not supported whatsoever. There needs to be initial access to a few things there. I'm sure it could be made to work with some initramfs hackery. But it is neither supported or wise to do so IMO.
I'll not do the separate partitions then. Thanks. I'll check back if it works/doesn't-works. -
I have this odd issue that I can't seem to figure out. I have an MDT Task Sequence that I created runs scanstate and loadstate without any issues using hard link. Unfortunately, the user profiles are not loaded/restored after loadstate runs. I can go to
the StateStore folder and manually run the loadstate again or use the Windows Easy transfer to restore the users, but I want this to occur when loadstate runs.
Here is the loadstate log:
2014-03-30 18:01:10, Info [0x000000] USMT Started at 2014/03/30:18:01:10.787
2014-03-30 18:01:10, Info [0x000000] Command line: C:\_SMSTaskSequence\Packages\CMP0010E\x86\loadstate.exe C:\StateStore /c /v:5 /l:C:\WINDOWS\system32\CCM\Logs\SMSTSLog\loadstate.log /progress:C:\WINDOWS\system32\CCM\Logs\SMSTSLog\loadstateprogress.log
/i:C:\_SMSTaskSequence\Packages\CMP0010E\x86\MigApp.xml /i:C:\_SMSTaskSequence\Packages\CMP0010E\x86\MigUser.xml /ue:*\* /ui:company.local\*
2014-03-30 18:01:10, Status [0x000000] Activity: 'MIGACTIVITY_COMMAND_LINE_PROCESSING'
2014-03-30 18:01:10, Info [0x000000] Script file specified: C:\_SMSTaskSequence\Packages\CMP0010E\x86\MigApp.xml[gle=0x000000cb]
2014-03-30 18:01:10, Info [0x000000] Script file specified: C:\_SMSTaskSequence\Packages\CMP0010E\x86\MigUser.xml[gle=0x000000cb]
2014-03-30 18:01:10, Info [0x000000] Replacement Manifests are processed because this OS version has built-in component manifests
2014-03-30 18:01:10, Info [0x000000] The ReplacementManifests folder used to service system component manifests is not present. OS settings migration will be done with system component manifests
installed onto the system.
2014-03-30 18:01:10, Info [0x000000] Starting the migration process[gle=0x00000006]
2014-03-30 18:01:10, Status [0x000000] Activity: 'MIGACTIVITY_MIGRATION_START'
2014-03-30 18:01:10, Info [0x000000] Excluding path: C:\_SMSTaskSequence\Packages\CMP0010E\x86
2014-03-30 18:01:10, Info [0x000000] Excluding path: C:\StateStore
2014-03-30 18:01:10, Info [0x000000] Excluding path: C:\WINDOWS\system32\CCM\Logs\SMSTSLog\loadstate.log
2014-03-30 18:01:10, Info [0x000000] Excluding path: C:\WINDOWS\system32\CCM\Logs\SMSTSLog\loadstateprogress.log
2014-03-30 18:01:10, Info [0x000000] Excluding path: C:\_SMSTaskSequence\Packages\CMP0010E\x86\MigApp.xml
2014-03-30 18:01:10, Info [0x000000] Excluding path: C:\_SMSTaskSequence\Packages\CMP0010E\x86\MigUser.xml
2014-03-30 18:02:55, Info [0x000000] Leaving MigCloseCurrentStore method
2014-03-30 18:02:55, Status [0x000000] Activity: 'MIGACTIVITY_SUCCESS'
2014-03-30 18:02:55, Info [0x000000] Success.[gle=0x00000006]
2014-03-30 18:02:55, Info [0x000000] USMT Completed at 2014/03/30:18:02:55.116[gle=0x00000006]
2014-03-30 18:02:55, Info [0x000000] Entering MigShutdown method
2014-03-30 18:02:55, Info [0x080000] COutOfProcPluginFactory::FreeSurrogateHost: Shutdown in progress.
2014-03-30 18:02:55, Info [0x0803e6] Removing mapping for HKLM
2014-03-30 18:02:55, Info [0x0803e7] Successfully unmapped HKLM
2014-03-30 18:02:55, Info [0x0803e6] Removing mapping for HKU
2014-03-30 18:02:55, Info [0x0803e7] Successfully unmapped HKU
2014-03-30 18:02:55, Info [0x080487] Destroying OS analysis service
2014-03-30 18:02:55, Info [0x080488] Destroyed OS analysis service
2014-03-30 18:02:55, Info [0x000000] Leaving MigShutdown methodI've got this to work although I haven't figured out the root cause.
My initial OSDMigrateAdditionalCaptureOptions were: /Hardlink /nocompress /uel:30 /config:%_SMSTSMDataPath%\Packages\%_OSDMigrateUsmtPackageID%\%Processor_Architecture%\config.xml"
My OSDMigrateRestoreCaptureOptions were: /Hardlink /nocompress /ue:*\* /ui:domain.local\*
Since the restore was failing, I removed the domain name from the ui switch which magically caused the restore process to load the user profiles to the computer.
My final OSDMigrateRestoreCapptureOptions which worked: /Hardlink /nocompress /ue:%computername%.
Just to note /hardlink commands are not necessary when you are using MDT task sequence, but I put it in anyway and it seems ensure that I get consistent results. -
Query Transported Successfully : But transported query is not available in PRD system
Hi Gurus,
I have transported one query yesterday. And transport got successful with out any errors.
Now i am checking the same query in PRD system, but i am not able to find the query.
Checked in RSRT and Query Designer in PRD System.
Table RSZCOMPDIR is showing only M version of the query in PRD.
Please help to fix this issue.
Regards,
PRKHi,
have you cheeked the STMS there showing return code - 0,4,8,15 means success or warning or red?
have you transported successfully form dev to qav?
are you seeing same query in qas?
if not available same query on PRD please re import the one more time.
check the RSRT giving the technical name of query and check the multi provider.
Thanks,
Phani. -
Inventory record is deleted but quant is in 'Not counted' status within Bin
Hi Gurus,
I have a problem which is related to Inventory count in warehouse. The Bins are showing certain Inventory number is as not counted ( against the quant in Inventory tab of Bin) . But when I go to the Inventory record, I find it's deleted. For an ideal situation when an Inventory record is deleted, the bin should update the quant as Cancelled aginst the Inventory number, in the Invent. tab on Bin. But instead this is updated as 'Not counted'.
This is causing me a problem regarding any transfer transfer of those stocks since in the LQUA table the Inventory Active is checked.
Can you please help me.
Thanks in advance
Amithi pavan,
whats happening is just to give u an idea about my tables, i have
SELECT prod_code, prod_name, prod_qty_in_hand from product_MASTER
PROD_C PROD_NAME PROD_QTY_IN_HAND
2002 PROD2 10.000
2003 PROD3 20.000
2004 PROD4 30.000i have a master-detail Form for PURCHASE_ORDER_HEADER & PURCHASE_ORDER_DETAIL
(with Delete Record Behavior property set as Cascading),
for example lets say if i have record like
SQL> SELECT POH_CODE,POH_NO, POH_PARTY_CODE FROM purchase_ORDER_HEADER;
POH_CO POH_NO POH_PA
PUR 1.000 1001
SQL> SELECT POD_POH_CODE,POD_POH_NO,POD_PROD_CODE,POD_QTY FROM purchase_ORDER_DETAIL;
POD_PO POD_POH_NO POD_PR POD_QTY
PUR 1.000 2002 5.000
PUR 1.000 2003 8.000
PUR 1.000 2004 10.000whats happening is, on form when i am querying record, lets say i want to delete the PO_header record no.1,
it should obviously delete the 3 records of PO_Detail (due to cascade property), and also, reduce the prod_qty_in_hand field for the 3 items 2002,2003 & 2004 (deleted from the PO_detail above), from the PRODUCT_MASTER Table, to 5,12 & 20 respectively.
i am able to update the prod_qty_in_hand , if after query, i go in the detail section & delete a particular record, but can't do it at header level with given the pre-delete code that i posted in my first post.
hope i am -
Adobe flash player has downloaded successfully, but it's still not working
hello all, I have a new week old laptop, that has windows 7, I'm trying to view videos online, like on youtube, but it keeps saying download flash player, so I download it, then it says it again when i try to watch the videos. I've downloaded it about 10 times now! with the same result, I followed the instructions on the help pages about changing my settings and it still doesn't work. Please help.
You write that you "downloaded" Flash Player, but did you also install it?
What is your web browser? If Internet Explorer, check
http://forums.adobe.com/thread/885448
http://forums.adobe.com/thread/867968 -
Dear all:
I use BSP_WINCE_ARM_A8_01_02_00_Source.exe( EVM_3530.sln ) to build wince 6.0(bin) for beagleboard xm rev C,
the visual studio build success, but the beagleboard can not into win ce, I log the message by uart, my log show as
below:
Texas Instruments Windows CE SD X-Loader for EVM 3730
Built Apr 28 2015 at 13:44:21
Version BSP_WINCE_ARM_A8 1.02.00.02
open ebootsd.nb0 file
Init HW: controller RST
SDCARD: reqested speed 1000000, actual speed 1000000
SDCARD: reqested speed 25000000, actual speed 19200000
jumping to ebootsd image
Microsoft Windows CE Bootloader Common Library Version 1.4 Built Apr 28 2015 13:
41:17
Texas Instruments Windows CE EBOOT for OMAP35xx/37xx, Built Apr 28 2015 at 13:44
:09
EBOOT Version 0.0, BSP BSP_WINCE_ARM_A8 1.02.00.02
TI OMAP3730 Version 0x00000012 (ES1.2)
TPS659XX Version 0x30 (ES1.3)
System ready!
Preparing for download...
INFO: Predownload....
NAND manufacturer 0 device 0 : no matching device found
ERROR: FMD_Init call failed!
NAND manufacturer 0 device 0 : no matching device found
ERROR: FMD_Init call failed!
WARN: Boot config wasn't found, using defaults
INFO: SW4 boot setting: 0x12
NAND manufacturer 0 device 0 : no matching device found
>>> Forcing cold boot (non-persistent registry and other data will be wiped) <<<
Hit space to enter configuration menu 5...
Hit space to enter configuration menu 4...
Hit space to enter configuration menu 3...
Hit space to enter configuration menu 2...
Hit space to enter configuration menu 1...
Init HW: controller RST
SDCARD: reqested speed 1000000, actual speed 1000000
SDCARD: reqested speed 25000000, actual speed 19200000
BLSDCardReadLogo: cannot open Logo.bmp
BL_IMAGE_TYPE_BIN
Download file information:
[0]: Address=0x80002000 Length=0x023a78cc Save=0x80002000
Download file type: 1
.............rom_offset=0x0.
..ImageStart = 0x80002000, ImageLength = 0x23A78CC, LaunchAddr = 0x800122F8
Completed file(s):
[0]: Address=0x80002000 Length=0x23A78CC Name="" Target=RAM
ROMHDR at Address 80002044h
Launch Windows CE image by jumping to 0x800122f8...
Windows CE Kernel for ARM (Thumb Enabled) Built on May 7 2012 at 12:47:43
OAL: CPU revision 0x12:DM3730
OAL: CPU L2 Aux register 0x400042
****Profiler Build****
---High Performance Frequency is 26000914 hz---
Does anyone know what happen?
Thank for your help, VictorThere is an option in boot loader menu to enable debug messages "Enable/Disable OAL Retail Messages". Looks like you haven't enabled it. check it.
Please mark as answer, if it is correct.
Please vote,if it is helpful post.
Vinoth.R
http://vinoth-vinothblog.blogspot.com
http://www.e-consystems.com/windowsce.asp -
Advertisment Report says successful but program did not install...help?
I created the package and package works outside of sccm. Here is the execmgr.log info which says the program installs successfully but the progam is not on the machine. It is in the cache but does not seem to install... what's happening?
Policy is updated for Program: Lego Mindstorms, Package: NP1003A8, Advert: NP120365 execmgr 1/28/2010 3:51:35 PM 2820 (0x0B04)
Policy is updated for Program: Lego Mindstorms, Package: NP1003A8, Advert: NP120365 execmgr 1/28/2010 4:01:18 PM 3900 (0x0F3C)
Mandatory execution requested for program Lego Mindstorms and advertisement NP120365 execmgr 1/28/2010 4:04:34 PM 3848 (0x0F08)
Creating mandatory request for advert NP120365, program Lego Mindstorms, package NP1003A8 execmgr 1/28/2010 4:04:34 PM 3848 (0x0F08)
Requesting content from CAS for package NP1003A8 version 2 execmgr 1/28/2010 4:04:34 PM 3848 (0x0F08)
Successfully created a content request handle {68625778-FDE1-4EEF-BA7A-4276FCDFFB7D} for the package NP1003A8 version 2 execmgr 1/28/2010 4:04:34 PM 3848 (0x0F08)
Raising event:
[SMS_CodePage(437), SMS_LocaleID(1033)]
instance of SoftDistWaitingContentEvent
AdvertisementId = "NP120365";
ClientID = "GUID:1340803F-10E6-4EF4-8CDA-5CB17EB24979";
DateTime = "20100128210435.308000+000";
MachineName = "PD-224-10";
PackageName = "NP1003A8";
PackageVersion = "2";
ProcessID = 1996;
ProgramName = "Lego Mindstorms";
SiteCode = "NP1";
ThreadID = 3848;
execmgr 1/28/2010 4:04:35 PM 3848 (0x0F08)
Successfully raised SoftDistWaitingContentEvent event for program Lego Mindstorms execmgr 1/28/2010 4:04:35 PM 3848 (0x0F08)
Execution Request for package NP1003A8 program Lego Mindstorms state change from NotExist to WaitingContent execmgr 1/28/2010 4:04:35 PM 3848 (0x0F08)
Content is available for program Lego Mindstorms. execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
CExecutionRequest::Overriding Service Windows as per policy. execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Execution Manager timer has been fired. execmgr 1/28/2010 5:06:49 PM 820 (0x0334)
Executing program LegoMindstorms.exe in Admin context execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Execution Request for package NP1003A8 program Lego Mindstorms state change from WaitingContent to NotifyExecution execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Checking content location C:\WINDOWS\system32\CCM\Cache\NP1003A8.2.System for use execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Successfully selected content location C:\WINDOWS\system32\CCM\Cache\NP1003A8.2.System execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
GetFileVersionInfoSize failed for file C:\WINDOWS\system32\CCM\Cache\NP1003A8.2.System\LegoMindstorms.exe, error 1812 execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Executing program as a script execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Successfully prepared command line "C:\WINDOWS\system32\CCM\Cache\NP1003A8.2.System\LegoMindstorms.exe" execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Command line = "C:\WINDOWS\system32\CCM\Cache\NP1003A8.2.System\LegoMindstorms.exe", Working Directory = C:\WINDOWS\system32\CCM\Cache\NP1003A8.2.System\ execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Created Process for the passed command line execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Raising event:
[SMS_CodePage(437), SMS_LocaleID(1033)]
instance of SoftDistProgramStartedEvent
AdvertisementId = "NP120365";
ClientID = "GUID:1340803F-10E6-4EF4-8CDA-5CB17EB24979";
CommandLine = "\"C:\\WINDOWS\\system32\\CCM\\Cache\\NP1003A8.2.System\\LegoMindstorms.exe\"";
DateTime = "20100128220649.886000+000";
MachineName = "PD-224-10";
PackageName = "NP1003A8";
ProcessID = 1996;
ProgramName = "Lego Mindstorms";
SiteCode = "NP1";
ThreadID = 3212;
UserContext = "NT AUTHORITY\\SYSTEM";
WorkingDirectory = "C:\\WINDOWS\\system32\\CCM\\Cache\\NP1003A8.2.System\\";
execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Raised Program Started Event for Ad:NP120365, Package:NP1003A8, Program: Lego Mindstorms execmgr 1/28/2010 5:06:49 PM 3212 (0x0C8C)
Program exit code 0 execmgr 1/28/2010 5:07:10 PM 3212 (0x0C8C)
Looking for MIF file to get program status execmgr 1/28/2010 5:07:10 PM 3212 (0x0C8C)
Script for Package:NP1003A8, Program: Lego Mindstorms succeeded with exit code 0 execmgr 1/28/2010 5:07:10 PM 3212 (0x0C8C)
I am having exact same issues on Lego Mindstorm 2.0 - usig sccm 2012R2
Fatal Error. Required MSI directory property PersonalFolder is in an invalid location. "C:\doucments and
setting\local service]My doucments" which does not exist the target machines
what was the resolution for this?
I would really appreciate any help regarding this.
Have you looked at creating an MST yet? that would be my first step. My second step is to call Lego and get their support to tell you how to deploy their application to an enterprise environment.
Garth Jones | My blogs: Enhansoft and
Old Blog site | Twitter:
@GarthMJ -
Job finished successfully but Spool not generated(no spool icon)
I am generating a report which . When the program in scheduled, the job completed successfully but spool icon is not available. Could any one suggest us the reason why spool has not generated. Thanks in advance!
Hi,
When executing report, Spool gets generated only when an Output is generated. Please check if output exits for the selection criteria.
Also check any special mechanisms are used that diverse the ouput when executed in background. -
hi everyone, i am using a bat file to package an air file ,
this application runs on windows 7 32 bit,
it need to call another windows application , so i google and then find i need to add -target native when package , so i added.
the bat file is like below:
========================================
@echo off
:: AIR application packaging
:: More information:
:: http://livedocs.adobe.com/flex/3/html/help.html?content=CommandLineTools_5.html#1035959
:: Path to Flex SDK binaries
set PATH=%PATH%;C:\AdobeAIRSDK\bin
:: Signature (see 'CreateCertificate.bat')
set CERTIFICATE=yeahCert.pfx
set SIGNING_OPTIONS=-storetype pkcs12 -keystore %CERTIFICATE% -tsa none
if not exist %CERTIFICATE% goto certificate
:: Output
if not exist air md air
set AIR_FILE=air/jonnson.air
:: Input
set APP_XML=application.xml
set FILE_OR_DIR=-C bin .
echo Signing AIR setup using certificate %CERTIFICATE%.
call adt -package %SIGNING_OPTIONS% -target native %AIR_FILE% %APP_XML% %FILE_OR_DIR%
if errorlevel 1 goto failed
echo.
echo AIR setup created: %AIR_FILE%
echo.
goto end
:certificate
echo Certificate not found: %CERTIFICATE%
echo.
echo Troubleshotting:
echo A certificate is required, generate one using 'CreateCertificate.bat'
echo.
goto end
:failed
echo AIR setup creation FAILED.
echo.
echo Troubleshotting:
echo did you configure the Flex SDK path in this Batch file?
echo.
:end
pause
======================================================
after run this bat , the air file is successfully built , but when i want to install this air , it says "sorry ,an error has occured ..... bla bla installer file is damaged....bla bla "
but when i remove the red part -target native in the command above then run it again , the new packaged air file can install successfully, but the application can not call other windows apllication anymore, nativeprocess.issupported always returns false when running
so seems like the problem is all about -target native , deos anyone know whats wrong ?
this problem really bothers me long time , any help will be appreciated. thanks in advance!Nice! I swear I tried that URL (substituting "mac" for "win" and "MAC" for "WIN" in the one relaxatraja posted), but I guess I missed something.
Ironically, it doesn't include a binary either, but a simple alias works:
alias pfi='java -jar /path/to/PFI/lib/pfi.jar'
And it did indeed produce an ipa without error. I don't have my hardware with me, but I'll be able to test it tonight. Meanwhile, I think I'm in business. Thank you all! -
HT1414 I restored my phone successfully but the Wi-Fi is still grey and is off?
I restored my phone successfully, but I still can not turn my wifi on. It is grey and OFF. I need assistance. I believe without this On, I can not upload my icloud....
http://support.apple.com/kb/TS1559
Additional Information
If you are still unable to turn Wi-Fi on, please contact Apple for support and service options. -
Win98 not getting inventory scan
Our XP systems are getting the inventory scan and importing it into
the
database, but our Win98 systems are not.
Recently I deleted all the workstation objects, then ran a sync to the
database to clear it out. I then ran unreg32 at each workstation and
let
them reimport themselves and rerun the inventory scan.
The XP systems worked fine. The win98 systems imported into the NDS
with
the minimal workstation info. But none of the info got into the
database. When you look in nds and ask for more workstation info,
almost
everything comes up with "NO INFORMATION FOUND".
It looked like it was just scanning for delta info, so yesterday I
went
into ConsoleOne and checked start full scan for every win98
workstation.
Now when I look at the java interpereter on the console, Win98 systems
aren't showing up as getting scanned at all.
If I look at the Scan status, I get the following messages:
Scanner(Warning) : 027: Unable to read the sequence number from the
Workstation Object.
Scanner(Information) : 024: Initiated scan successfully.
Scanner(Information) : 009: Software Scan done using Microsoft
Installer
(MSI).
Before I asked for the full workstation scan, I would also get this
message, but I don't get it anymore.
Storer(Information) : 200: The Storer has updated the database.
Thanks,
Pam[email protected]
> I suppose I could try upgrading the clients & see if the upgrade
> resets whatever is stuck?
For zen 3.0 you really are at the newest client you can be, or maybe
even too new.
I would try this next, although I don't know if it will fix it.
1. Make Sure the "Enable Software Scan" box is checked.
2. Create a new Workstation Package and reconfigure the inventory
policies.
3. Restart the server, unless you have already done that.
Let me know if that helps.
Jared L Jennings
Novell Support Forums SysOp
Geek by Nature, NetWare by Choice. -
ZCM Inventory Scan of a NetWare 6.5 Server
I was able to install the ZCM Adaptive Agent for NetWare servers on all of my NetWare servers, and I can see these servers in Devices/Servers after performing a discovery.
How can I run an inventory scan for these NetWare servers so I can get more detailed information about these servers?
Thank You,
Ray BarryOn Thu, 28 Feb 2008 20:44:31 GMT, Raymond Barry wrote:
> How can I run an inventory scan for these NetWare servers so I can get more detailed information about these servers?
probably better posted in the ZCM inventory forum...
but.. if you go to configuration of your zone and than device management (I
think) you will find inventory only schedules
Marcus Breiden
If you are asked to email me information please remove the - in my e-mail
address.
The content of this mail is my private and personal opinion.
http://www.didas.de -
Workstation inventory scanning
hi
I am not able to perform workstations inventory scan in consoleone. But if
i run ZfdInvscanner.exe from c:\program files\novell\inventory, it worked.
When I right click the workstation object in consoleone, under properties,
Zenworks inventory, workstation scan configuration, I click on "Start Full
Scan", and It doesn't work for me. Can you please tell me what goes wrong
and how to make it work ... ThanksIn article <[email protected]>, [email protected] says...
> performing that action through ConsoleOne tells the inventory service
> "next time this workstation does an inventory scan, make it a full
> scan" - it doesn't tell it to go and scan that minute. control of when
> a scan takes place is via the inventory policy in the workstation
> policy package.
Check with wmsched.exe, you can force a run via that if you wish.
/Fribse
Barry (Sysop): "Then again, I'm a single CPU fan..."
Bob (Trafficshaper): "You can get a job cooling CPUs? Does it pay
well?"
Maybe you are looking for
-
Workarounds in Numbers 3.0?
Dear Fellow Numbers 3.0 Users, In Numbers 3.0, some features have been lost that were in Numbers 2.3. However, I have seen some creative ideas in this forum for ways to work around the loss of features yet maintaining the functionality. Example 1: h
-
Ability to turn headings into graphics when creating PDFs
I would like the ability to convert the text headings and footers into graphical images whenever I create PDFs. My reason for this wish is that when you search for a text string in a PDF, it is very annoying when you keep getting hits that occur in h
-
Xcode "fails with exit code 1"
I'm new to xcode, 13 years old, and it stopped compiling my code! I'm working in C++ command line. My first project worked fine, but when I tried to run a new project, the build failed (not from syntax errors or anything) and gave me this notificatio
-
Security questions and account disabled and no recovery email
i have forgotten my security questions and the email for recovering it has been disabled, how do i get acces to my account fully again
-
Nokia 6300 pc suite isnt setting up on my pc help ...
ive just brought a 6300, and im trying to get the pc suite set up on my pc and it just wont load it on to my pc, it comes up with a critical error and something a bout a HKEY ??? help me please !!