Is dual-layer DVD capability real?

Has aaaaaaanyone been successful in burning a 2 hour movie to a dual-layer disk. I have tried two different Macs (08 laptop and 09 tower), have varied burning speed( from fastest possible to 1x), used 2 different brands of disks and tried playback on two different DVD players. The disks always choke and skip about 2/3 of the way through the movie. If Apple is going to advertise and sell a capability, they should first make sure it works reasonably well in real world conditions. It shouldn't be this difficult.

Is dual-layer DVD capability real?
It works for me. I use iMovie 06 with iDVD 09/08.

Similar Messages

  • Two hour sequence to dual-layer DVD?

    Hi,
    I'm confused.
    I have a two hour 16:9 sequence (actually 1 hour, 56 minute) that I want to put on a dual-layer DVD. I guess I didn't fully think it through when I sent it from FCP to Compressor and selected DVD 16:9 120 minute fastest encode, because it compressed it to 4.04 gigs rather than twice that size at a better quality. Now I'm looking for a setting that tells it my destination is a dual-layer DVD and I don't see it.
    Additionally, the m2v file that came from that process cut off the final minute or so of my sequence. Why in the world would that happen?
    Kenny

    These instructions assume you're using DSP for authoring. I don't know if iDVD has DL capability.
    The 'calculator' in Compressor assumes a single layer DVD. The key is to look at the summary, which is the far left tab in the Inspector. About 1/3 from the top, it will show the estimated file size. Adjust the bit rate selector until you get the file size approaching the capacity of the Dual Layer disk. You have other restrictions to consider as well. Totally data rate of video(s)audio(s)other data cannot exceed the maximum for the DVD spec (nominally 10mb/s).
    Once inside DSP, when you burn the disk, you'll be asked to select a marker to indicate where the burner will change from writing to the first layer to the second layer. This should occur at a convenient location in the video (a fade to black, eg.) near the end of the first layer capacity. If you don't already have a marker near that point, be sure to add one for the switch-over.
    Good luck
    allen

  • Dual Layer DVD...

    I want to burn my movie onto a dual layer DVD. There is a selection in DVDSP4 for dual layer, but how do I prep it for a lower compression/dual layer option in Compressor?

    Not necessarily - passes impact the encode time, the first pass is a test encode, the second one is the real thing (think of it has a rough draft). It has nothing to do with whether you're using single or dual layer media.
    It shouldn't change size in DVDSP - once the file is encoded that's it - it's going to stay that size no matter what. If its coming out at 4.7 GB you may be able to get away with single layer media.
    Message was edited by: wallybarthman

  • Does G5 1.8 GHz write to dual layer DVDs?

    I have large picture library that's more than a normal DVD can hold, but will fit on a dual layer DVD. When I put the DL disk in, my Mac just spits it out. It won't even recognize it. G5, machine model PowerMac9,1, PowerPC g5 (3.0). Pioneer DVD-RW DVR-117D - all from System Profiler.
    Thanks, Josh

    The Pioneer DVR-117D is in reality a DVR-108 that Apple has modified (read: crippled) the firmware on. One of the features that was removed was the ability to burn DVD+R DL discs (it will not write to DVD-R DL discs).
    If you want to bring back the DL write capability, you'll need to force flash the drive with the firmware for a DVR-108. See this post here on Discussions with instructions on how to do the flash. Make sure that you use the links from my post in that thread to the flashing program and to the firmware files. The original article that's linked to in that thread references outdated files.

  • Dual layer dvd burning

    Hi,
    I need some help regarding dual layer dvd burning.
    I never burned a dual layer dvd before and am going to in the next few days for a big movie screening. So I better get this right.
    How do I set the layer break? do I just set it to be automatic or should I set a chapter in the track? if yes, then where do I suppose to put the chapter.
    Is there any advise regarding dual layer burning ? so that I have less possibilities of messing things up.
    Its a 115 mins movie. Im planning to encode it with 6.5 avg 8 max.
    Is it safe to put a lot of chapters in?
    I won't have dvd menu. I will just set it to play straight away.
    thanks.
    Jack

    I'm not an expert in the least but I have worked with duel layers and let me tell you than can be a real s.o.b. I'm not sure what the scoop is on them but they tend to glitch out while your burning. I made three and 1 worked perfect the other two not at all and for some reason the 1 that did work only played on about half of the DVD players they were played on. When I got it into a DVD player that worked the chapter markers were not a problem. I had four seperate segments that were linked up and played fine. We used this for a screening in front of about 400 people.
    Our feature was about the same length as yours so after the screening we decided to just take the quality down a little (which you can't even tell) and put it on a normal DVD R. We saved a ton in duplication.
    Setting the Duel Layer is pretty easy, it's all in the inspector under the disc/volume tab but make sure that in your outline window the main DVD at the top is highlighted. I don't think it matters if you have a chapter in the middle of the footage or anything like that. You can just link up one long stream if needed. Be sure to try out the DVD on the actual player you are going to use. Good luck.

  • Dual Layer DVD Support

    Does anyone know if the current iBook G4 14" (Dual USB, 1.42GHz) that comes with a SuperDrive standard, supports dual layer DVD media? I'm trying to find out on my system in System Profiler and in Toast drive features, but I can't seem to find out anywhere.
    DVD Drive: MATSHITA DVD-R UJ-845E, with support for R,-R,RW,-RW

    Theoretically, the UJ-845 is capable of burning dual-layer DVD+Rs, according to Panasonic/Matshita's specs. Apple disabled this feature in the firmware, however, in order to maintain product distinction between the iBooks and the Powerbooks. The dual layer-capable Powerbooks actually use a different model drive entirely, IIRC. As far as I know, there is no way to patch the drive to enable dual layer burning.
    Right now the Macs with dual layer burning capability are the new Powerbooks, the new iMac, and the Power Mac G5.

  • Dual layer DVD-R versus Dual layer DVD+R

    Is there a difference between dual layer DVD-R discs and dual layer DVD+R discs? On a related note, is there a difference between dual layer DVD-RW discs and dual layer DVD+RW discs? Is one )-R vs +R, for example) better than the other?

    OK, after what I've read in the link, the impression I got is that DVD+R is more reliable than the DVD-R . . . and since my alum Intel iMac is capable of reading adn burning to both, I shouldn't have any problems using a DVD+R. Am I correct?

  • Deciding layers on dual layer DVD

    Is it possible to controll what material comes on what layer on a dual layer DVD?
    I can imagin it would be best if the feature movie and all related assets (5.1, stereo and commentators audiostreams) all reside on one layer, while the menues and everything els resides on the other layer.
    Is this possible, and if so, how?
    cordially
    Per

    You can make an estimate of the size of the assets (the audio is all on the same track if you are using alternate audio streams so really no way to move them unless using multiple video tracks with different audio)...you can move items in the outline view up and down to change the VTS is built to, and the first side has to be larger.
    The real benefit is to keep things together so they do not have to cross the break point when playing
    Menus are basically at the beginning of the disc

  • Optical drive won't burn dual layer dvd

    Yes, mine is capable of burning Dual layer dvds. It was the $1299 Core 2 Duo version 1 rev. ago. Got it in October. In the System Profiler it says DVD-Write: +R DL.
    So, I stick a +R DL disk in there, and every time I go to write to it, the disc gets spit out and it says please insert a blank dvd. Now, you might think I'm inserting full DVD+r DL disks, however, that's impossible, because this is my only dvd writer I own and there is no way every disk in my pack came out of the box full of data.
    Is there a brand that is guaranteed to work, does just my optical drive suck, or do all optical drives in macbooks suck and it's just a silly joke? I've seen quite a few threads claiming their dual layer writers don't work.

    Noah Apodaca1 wrote:
    I'm also having difficulties burning DL discs. I'm using Toast Titanium 7.1.2 and I just got done with 30+ minutes of burn time only to receive an error stating "The drive reported an error: Sense Key = MEDIUM ERROR; Sense Code = 0x02; NO SEEK COMPLETE"
    I've been trying to use Windata DVD+R DL discs and I've got a nice collection of coasters so far. Is this something I should use my AppleCare to try to address, or is this a media issue?
    I have experienced the EXACT same problem using Memorex DVD+R DL discs (not my fave), so I do not believe this has anything to do with the brand of discs.

  • Firmware upgrade for Matshita DVD-R UJ-845E to burn dual layer DVD?

    Dear All
    I have a PowerBookG4 with a Matshita DVD-R UJ-845E which it seems apple has disabled from burning dual layer DVD. I've read around that there are firware upgrades that can enable actions again. I can't find any for Matshita DVD-R UJ-845E, though. Any ideas?
    Thank you!
    Angie
    PowerBookG4   Mac OS X (10.4.8)  

    angie1976 you have me directly.
    As stated in previous posts there have been several issues with the Matshita Optical drives that Apple has installed in there computers. Over time the problem has been discussed and it would appear that there are several things that come into play here.
    Apple has made it so that many of the drives they intall are in fact not capable of there full potential.
    It in fact boils down to an issue of Copywrite Infringment. Apple doesn't want to put itself in a position to be open to Lawsuits from the Motion Picture Industry.
    Many of the drives that do not work up to there full potential have FIRMWARE updates that are offered by the manufacture to remedy this problem and some do not.
    It has also been found that the casual user that burns DVD's isn't aware of the huige difference in the Format's available for DVD Burning. and the many limitations of these different drives as far as Media and Speed of Media is concerned. Many of the DL burners that were installed will not burn DL. Apple has had such a huge amount of dissatisfied customers that many that will take the time and if they still have AppleCare these drives will be replaced free of charge.
    Here are a collection of links that will help you to understand the problem as it exists.
    I will also say that upwards of 85% of the problems user expieriance is with POOR QUALITY MEDIA.
    http://www.digitalfaq.com/media/dvdmedia.htm
    http://www.videohelp.com/dvd
    I also noticed that some others have chimed in as to the fact that Media was not the issue. This is not entirely true.
    Here is another post that I answered that will also cover this subject that may help you understand the problem a little better.
    Let me see if I can shed some light on this issue, for you.
    Maybe some others as well can.
    There are several Applications that are standard programs that come with OSX.
    Of these, several have the ability to burn a project.
    iTunes....iMovie.....Disk Utility.
    Each of the above mentioned applications were developed for a specific purpose. However, they are capable of doing more than the original developers intended.
    The problem in my eyes is the lack of information for a new user to Mac.
    In what one would consider the perfect world, you simply choose a project, drag it in to one or more of the applications mentioned above and simply click burn and you are finished.
    This is not always the case.
    Often users are left with the issue of no clear cut direction on how to use these different burning softwares, and the ability to have a clear cut step by step user interface.
    All of the furnished OSX burning software is in fact usable and works well.
    The problem is HOW TO USE THEM.
    The more experienced users find this either to be a non issue or will take the time to work with these different applications until they figure out how to use them.
    There are of course different Advertisements and FAQ's that cover these to some degree that leave users more confused than when they started.
    One of the major issues that accompany this problem is this.
    Not all Burners that Apple uses in there machines are the same.
    Not all Burners will accept all the different Media's that are available on the market.
    Thus leaving many users confused. Not having a clear cut understanding of what the difference is between these different Media's and there use.
    http://www.videohelp.com/dvd.htm
    The above link offers an overview of this subject.
    Apple has found itself in a delima with the Motion Picture Industry, as well as The Music Industry over the issue of offering there users with the capability of copying Copyrighted material. Thus leaving them open for Law Suits.
    There was an in-depth article in one of the recent issues of Macworld Magazine, that went in-depth covering this issue.
    It is almost impossible to cover all aspects of this issue on these forums.
    There are of course different softwares available that make the burning experience much easier and user friendly.
    Roxio is one of the industry leaders in the development of Mac compatible Burning Software. They offer 2 of the industry leaders in this area.
    Toast-7 and Popcorn.
    This solves only one portion of the problem. Both of these software offering give the user the ability to copy about anything.
    However, there is so much controversy over the issue of Movie and Music copying, the manufactures of the Computers, and the Burners try to limit the users ability to copy these, and thus be clear of any Legal Issue.
    Here again rises the problem of computer users being mad because the industry has placed limitations on there ability to use there product in a fast easy to use method.
    Again there are work around to all of these issues.
    The problem then becomes who out there is willing to tell us what is the easiest most trouble free method of using these computers, burners, software,and media.
    The burner manufactures offer there burners.
    To get them to work to there full potential the users then must search out the 3rd party Firmware updates that will enable them to work properly. This is not an issue with all burners but quite a few.
    Most readers on these forums have read about the MEDIA compatibility and poor quality issues these are covered in a prior link.
    To sum this up, the resources are available to do just about anything one wants to do in the copy area.
    Not every copy problem is the same because of all the different elements that come into the equation, Burner, Media, Software, Firmware.
    So if a user has a problem and needs the information and the resources to copy there projects whatever they may be.
    Be through, give as much information as you can.
    Keep it simple, No need for the use of exotic terms that most people don't understand anyway.
    In-depth. Tell all aspects of the issue and what you have what you are using and what you want to accomplish.
    If there is an answer out there.
    Someone will Chime in.
    The users on these forums for the most part are more than willing to share in there knowledge, free of charge.
    One last thing,
    When a user gives you an answer for you problem, for the most part they believe it to be a fact. Sometimes this isn't the case, we have all been guilty of, this is not done with malicious intent. It is done trying to help.
    I personally have been misinformed, or tried a fix, that will work in one instance but not another. So tell all you can about your problem.
    Cheers Don

  • Burn Dual layer DVD+R 8.5 GB on OSx 10.5.8----Possible?

    I have 5.6GB of photos I want to burn to a DVD.  I bought memorex dual layer DVD+R 8.5 GB today. Burning failed. I have OSx 10.5.8. Can my computer burn a dual layer DVD?  How do I do it? 

    Would it be possible to buy and external dvd drive that would have the capability to burn dual layer?
    Yes.
    I know they have cd/dvd drives for the macbook air. But I'm wondering if I could buy it, hook it up, and it work with idvd.
    That model of drive will only work on a MacBook Air. You need a third-party model; iDVD 6 and newer can burn to external drives.
    (45871)

  • Problems burning dual layer DVD's

    we have had lots of problems trying to burn dual layer dvd's. Single layer has been fine but is there some secret trick for getting dual layer to work? we have tried both the internal dvd burner and an external one and both are supposed to be dual layer capable.

    about half of the ones we try get about half way through and then say media sense error (or similar wording) some of the others look like they have burned fine and then when it is writing the last little bit it just stops, this results in discs which are unreadable. The others look like they've burned fine and then don't play one of the items on the DVD once it is put in the machine.
    Those that do play appear to stop about the level of the switch of layers.

  • Leopard Dual Layer DVD, Macbook drive

    Well i'm planning upon purchasing leopard but i was wondering, does the 13inch macbook 1.8ghz model have a DVD reader capable of reading dual layer DVDs? I was wondering because i've noticed its called a Combo drive. Also when i bought my macbook, it came with tiger install DVDs, single layer, two of them. Anyone whos been able to install leopard on their macbook 13inch 1.8ghz proccessor, it would be great if you could just post a reply saying it works. I cant wait to order

    Thanks for the reply, but the only thing that makes me think now is, my drive cant burn DVDs, however it can read them, i suppose i only have to find one of my old windows DL DVDs and just try mounting them,
    Thanks

  • Can you copy onto dual layer dvds

    Have just purchased a 17" 1.67 ghz powerbook and was wondering if the dvd burner can burn onto dual layer dvds
    Many Thanks

    No currently shipping PowerBook is advertised as having the capability to burn dual layer DVDs, and they can't be burned in a single layer drive. To check what types of disks your optical drive can burn to in Tiger, choose About this Mac from the Apple menu and click on More Info. Once the System Profiler has opened, check the information for your burner; all the types of disks you can burn will be listed here.
    (9186)

  • Dual Layer DVD player or not?

    Maybe I should know it, but can anyone tell me if I have a Dual Layer or DVD-9 player on my iMac ?
    Model iMac7.1 - 2 Ghz Intel Core 2 Duo, bought in november 2007.
    I like to know if I can run the Adobe CS5 DVD before I buy it ...
    Thanks!

    I did check 'About my Mac' , but can not find anything about DVD Dual or 9...
    To confirm, you did click on More Info to get to System Profiler, then in the Hardware section, Disk Burning, what does it say under "Disk Write"? For example, mine says:
    DVD-Write: -R, -R DL, -RW, +R, +R DL, +RW
    which indicates a Superdrive that can write to both DVD-R DL & DVD+R DL disks.
    In the product information on the web there was a specific warning: DVD player must be able to run Dual Layer DVD (DVD-9). This is the reason for my question ...
    You may want to ask Adobe what they mean by that. If it's just to read dual layer disks, then like I said, any DVD drive can read a dual layer disk. But if one of the apps in CS5 needs to write to dual layer disks, then the recording capabilities become important. To me the wording "...player must be able to run..." infers that it's read, not write.
    However, I believe you are in luck. Everymac's website reports that your Mac should have a dual layer capable Superdrive. (Limited to writing to DVD+R DL only. But again, should be able to read any dual layer disk.)
    [http://www.everymac.com/ultimate-mac-lookup/?searchkeywords=iMac7,1|http://www.everymac.com/ultimate-mac-lookup/?searchkeywords=iMac7,1]

Maybe you are looking for