Is it possible to have a dual screen setup with an iMac (2012) and an iMac (mid 2007)?

Hello Everyone,
I have two iMacs. One is a 2012 model and the other is a mid 2007 model. Would I be able to use the mid 2007 model as an extra monitor?
I was going to purchase a mini dvi to mini display port cable and see what happens but I think it would be a good idea to see what everyone else thinks. Thanks for any suggestions!
- Nolan

The Apple Support Communities are an international user to user technical support forum. As a man from Mexico, Spanish is my native tongue. I do not speak English very well, however, I do write in English with the aid of the Mac OS X spelling and grammar checks. I also live in a culture perhaps very very different from your own. When offering advice in the ASC, my comments are not meant to be anything more than helpful and certainly not to be taken as insults.
I am thinking that won't work. The older iMac's video port only goes on direction - out. It won't take the signal from the newer iMac. You might be able to do something with this software;
http://www.screenrecycler.com/ScreenRecycler.html

Similar Messages

I have a dual-screen setup - Workspace Layout Panels - not functioning properly.

I have a dual-screen setup and since updating to 10.10.2, the panels open on the main screen - and not in the positions as they were saved in a Workspace layout.
Tried trashing the prefs - which works, but when I save a new Workspace layout, it does the exact same thing.
Any help is greatly appreciated. Thanks.

Hi Christopher,
This is a known issue and the product team is working with Apple to address it. Stay tuned.
Thanks,
Preran

[SOLVED] Dual-Screen Setup with ATI Catalyst

I'm having a beast of a time trying to set up X to work on my two screens.
Screen 1 is a 23" screen connected with a DVI cable. My preferred resolution for this one is 1920x1080. Screen 2 is a 17" screen (4:3) connected with a VGA cable. My preferred resolution for this one is 1280x960.
I tried using "aticonfig --initial=dual-head". This does not produce a working xorg.conf file. Specifically, my smaller monitor simply complains about not being able to display the given video mode. Running xrandr (from the main screen) shows only that output as being "connected" - the rest of them (including the CRT outputs which seem to correspond to the VGA port) as "disconnected".
I've spent about 5 hours searching for an answer to this, and the only ones I seem to be able to find are nvidia-specific.
I have an ATI Radeon HD 4850 or 4870 - I honestly forget which, although the drivers should be the same. I'm using the catalyst driver from the AUR, because I'd like to have 3D acceleration.
I've read through the entire xorg.conf man page, and tried a few things from there (including writing my own xorg.conf from scratch). Unfortunately, this seems incredibly useless, as the man page doesn't list any of the options that I seem to need (for example, I've read about and tried the "PairModes" option under "Device").
I can probably eventually figure this out, but it would be nice to have a few pointers. For example:
Should I have one or two "Device" sections in xorg.conf? Should I have one or two "Screen" sections in xorg.conf? Where can I find a full list of possible "Option" keys, at least for the Device section? Should I be using Xinerama (I've tried with and without, to no avail).
EDIT: I solved this by using the aticonfig tool some more, and not by messing around with xorg.conf. Specifically, the command:
aticonfig --initial=dual-head --xinerama=on --resolution=0,1920x1080 --resolution=1,1280x960 --screen-layout=right
I'll leave this here in the hopes that it can help someone else.
Last edited by Tempest (2011-08-06 02:28:41)

If you aren't playing games, it may be worth it to check out xf86-video-ati. Then you can configure your displays the standard way with xrandr.

Strange dual screen issue with HP Folio 1040 and docking station

Hi there,
I have a laptop in a docking station. Two displays are connected using the docking station's DisplayPorts. Instead of showing me two separate displays like I'd have expected, xrandr seems to "see" only one large screen.
Laptop: HP EliteBook Folio 1040 with Intel HD 4400 graphics card
Docking station: HP 2013 UltraSlim Docking Station
$ xrandr
Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 32767 x 32767
eDP1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 309mm x 173mm
1920x1080 60.05*+ 40.03
1400x1050 59.98
1280x1024 60.02
1280x960 60.00
1024x768 60.00
800x600 60.32 56.25
640x480 59.94
DP1 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
DP2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 510mm x 287mm
1920x1080 60.00*+ 59.94
3840x1080 60.00
2560x1024 60.00
1680x1050 59.95
1280x1024 60.02
1280x960 60.00
1280x720 59.97
1024x768 60.00
800x600 60.32
640x480 60.00 59.94
720x400 70.08
HDMI2 disconnected (normal left inverted right x axis y axis)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
eDP1 is the laptop's built-in display, while DP2 seems to represent _both_ displays. When I select 1920x1080, the two displays show the same. When I select 3840x1080, however, the two displays show a side-by-side setup, such that X11 spans over both of them. While I'm happy that I'm now able to make use of the second display, this obviously breaks some software stuff, like fullscreen video in vlc, for example. Any suggestions what I can do about that? Is it possible to software-split the screen such that it looks like a normal dual-head setup again?
Additional info:
$ lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)
$ X -version
X.Org X Server 1.15.1
Release Date: 2014-04-13
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.14.0-4-ARCH x86_64
Current Operating System: Linux elite 3.14.6-1-ARCH #1 SMP PREEMPT Sun Jun 8 10:08:38 CEST 2014 x86_64
Kernel command line: initrd=\initramfs-linux.img root=PARTUUID=88c068f1-bc0b-45b0-8836-182c29fe9b41 rw quiet
Build Date: 14 April 2014 08:39:09AM
Current version of pixman: 0.32.4
$ pacman -Qi intel-dri xf86-video-intel | grep Version
Version : 10.2.1-1
Version : 2.99.911-2

You could define two screens in xorg.conf similar to last post here. You would have to select the screen using the -display switch or the DISPLAY variable when using xrandr.

TS2570 I have the gray screen problem with the white apple and spinning wheel

I have the gray screen problem when it boots to the white apple and spinning wheel, but when I tried safe booting and doing the fsck thing I think I only made it worse, because it now starts, the safe mode progress bar comes on, (no matter if I press any keys or not) and after a minute shuts down again by itself. I also tried the command option, p, r thing and that did not work either, only brought me to the gray screen with the white apple, spinning wheel, and bar, and it promptly shut down. I am thinking more and more that I need the disk, but im not sure I have it. is it possible to order a new one online or is there another thing I can try? there is not an apple store nearby, and ereasing my data is not an option.
Also Im not sure what my exact opporating system is, but I did buy and download mountainlion in August so It is pretty new

Welcome to the Apple Support Communities
The hard disk is damaged. Take the Mac to an Apple Store

Is it possible to have a dual boot system with Windows that can ALSO be booted into a virtual machine optionally?

I have been looking for a solution to this for some time now. I want the convenience of a virtual Windows environment that can run simultaneously with OS X Lion--something I have right now using Virtualbox. But at the same time, there are graphics and processor-intensive Windows applications (for me, games and engineering applications) that don't run well at all in a virtual machine. So, here is what I am looking for:
A dual boot (i.e. bootcamp) system running Windows 7 and OS X Lion in which the Windows 7 machine can EITHER be booted as a virtual machine while running OS X OR booted physically so as to utitlize all system resources. The real trick however, is that I I want the virtual machine and the physical machine to be the exact same system. Meaning, if I boot physically into Windows and change something... rename a file, run a program and create a file, etc... those changes will all appear in the virtual machine.
Now, what are my options? I have read about Virtualbox and VMWare Fusion's "Raw Disk access" function but I can't tell if that's what I'm looking for or not... I half-thought that they were talking about converting a physical OS into a virtual machine, but without the intention of booting the physical OS again...
Also, I'm open to any software, free or otherwise. Thanks!

both VMWare Fusion & Parallels Desktop for Mac can use a bootcamp Windows installation as VM exactly like you want.

Dual Screen setup with laptop

I have the ideapad u400.. is it possitble to connect 2 external monitors to this machine to have 3 displays if not.. can i use the 2 external monitors and just close the lid to the laptop to use just 2 monitors?
let me know
Thanks.

As you need to connect two external monitor with your IdeaPad U400. You can connect the external Monitor via HDMI port, if it is available in your system.
Alternatively, you will need to create a two monitor connection via the USB input with a VGA to USB conversion cable, you can purchase these cables at any local computer store. And able this feature in your system.
Thanks & Regards,
Sameer
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Is it possible to have the "lock screen" stay lit up while I am charging my iPhone 4S?

Is is possible to have the "lock screen" stay lit up, and not go dark, while I am charging my iPhone 4S? I would like to turn off the sounds and vibrate but still be able to see the clock and see if any new messages come in.
Also, is there a setting or an app that will turn off all my sounds and vibrate at a given time, say 10pm and then turn it back on at 7am?

No and no.

X crashes on startup with AMD dual screen setup

Ever since I bought my AMD Kaveri A10-7850K at the end of January last year I've been having trouble getting a dual screen setup to work properly. Initially I put this down to poor beta drivers, and as I had far too much going on to investigate the issue further beyond some fiddling with xorg.conf, I bought an AMD A4-4000 as a temporary solution while waiting for the Catalyst drivers to catch up.
In June last year I decided to give my A10-7850K another go, assuming that the Catalyst driver would have matured enough in the meantime to cater for the Kaveri processors. Unfortunately the situation was still the same, and I I didn't have the time nor want to be swapping processors all constantly to I decided to just give up on a dual monitor setup for the time being.
After many years of using two screens, however, it is very hard to get used to a single monitor again, and as January is a quiet month for me I decided today to have another at getting it to work properly.
My setup is as follows:
an LG LG 23EA63V connected via HDMI as my main monitor at 1920x1080
a Viewsonic VP-171b connected via DVI as my secondary monitor at 1280x1024
AMD A10-7850K APU
Catalyst 14.12-1 drivers installed from Vi0l0's repo
Xorg 1.15 installed from Vi0l0's repo
KDE 4.14.3 using kwin
KDM is launched using kdm.service
KMS disabled via nomodeset
fglrx module loaded on boot via cat /etc/modules-load.d/catalyst.conf
Tear free rendering enabled
After plugging in my secondary monitor configuring it in amdcccle to be to the right of my primary moniotor in multi-display desktop mode, everything works correctly. This even works in my preferred setup where the secondary monitor is rotated into portrait mode, although I currently have not configured rotation so as to not overcomplicate the troubleshooting.
Upon rebooting, however, X hangs with a static white cursor in the top left hand of both screens, which after a while disappears completely. I then have to unplug the secondary (DVI) monitor and hard reset the PC before I can boot into my desktop again. The bizarre thing is though that when I plug in my secondary monitor again and configure it as desired, either through amdcccle or krandr, everything works perfectly again.
This is, of course, an incredibly cumbersome way of working, especially when most of the time I forget to disconnect my DVI monitor prior to turning on my PC, hence me just making do with a single monitor for the past 7 months.
I did a complete fresh install of Catalyst yesterday (uninstall drivers, delete remaining config files, reinstall drivers from repo), to no avail.
Output from xrandr after rebooting with the secondary monitor disconnected:
$ xrandr
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 16384 x 16384
DFP1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 510mm x 290mm
1920x1080 60.00*+ 50.00 59.94 60.00 50.00 59.94
1776x1000 50.00 59.94 50.00 59.94
1680x1050 50.00 59.95
1400x1050 50.00 59.98
1600x900 50.00 60.00
1280x1024 50.00 60.02
1440x900 50.00 59.89
1280x960 50.00 60.02
1280x800 50.00 59.81
1152x864 50.00 59.96
1280x768 50.00 59.81
1280x720 60.00 50.00 59.94
1024x768 50.00 60.00
1152x648 50.00 59.94
800x600 50.00 60.32
720x480 50.00 60.00 59.94
640x480 50.00 60.00 59.94
DFP2 disconnected (normal left inverted right x axis y axis)
CRT1 disconnected (normal left inverted right x axis y axis)
Output from xrandr after reconnecting the secondary monitor:
$ xrandr
Screen 0: minimum 320 x 200, current 3200 x 1080, maximum 16384 x 16384
DFP1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 510mm x 290mm
1920x1080 60.00*+ 50.00 59.94 60.00 50.00 59.94
1776x1000 50.00 59.94 50.00 59.94
1680x1050 50.00 59.95
1400x1050 50.00 59.98
1600x900 50.00 60.00
1280x1024 50.00 60.02
1440x900 50.00 59.89
1280x960 50.00 60.02
1280x800 50.00 59.81
1152x864 50.00 59.96
1280x768 50.00 59.81
1280x720 60.00 50.00 59.94
1024x768 50.00 60.00
1152x648 50.00 59.94
800x600 50.00 60.32
720x480 50.00 60.00 59.94
640x480 50.00 60.00 59.94
DFP2 connected 1280x1024+1920+0 (normal left inverted right x axis y axis) 338mm x 270mm
1280x1024 60.02*+ 75.02
1280x960 75.02 60.02
1152x864 75.00 60.02
1280x768 75.02 60.02
1280x720 75.02 60.02
1024x768 85.00 75.03 70.07 60.00
800x600 85.06 72.19 75.00 60.32 56.25
640x480 85.01 75.00 72.81 66.61 59.94
CRT1 disconnected (normal left inverted right x axis y axis)
my xorg.conf file:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-1"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Monitor"
Identifier "0-DFP1"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
Option "Position" "0 0"
Option "Rotate" "normal"
Option "Disable" "false"
EndSection
Section "Monitor"
Identifier "0-DFP2"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
Option "PreferredMode" "1280x1024"
Option "TargetRefresh" "60"
Option "Position" "1920 0"
Option "Rotate" "normal"
Option "Disable" "false"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
Option "Monitor-DFP1" "0-DFP1"
Option "Monitor-DFP2" "0-DFP2"
BusID "PCI:0:1:0"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-1"
Driver "fglrx"
Option "Monitor-DFP1" "0-DFP1"
BusID "PCI:0:1:0"
Screen 1
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Virtual 3200 3200
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-1"
Device "aticonfig-Device[0]-1"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
My Xorg.0.log:
http://pastebin.com/ki5A0T7R
I'm quite desperate to get this working, almost a year after buying my new setup, so any pointers are welcome!
Thanks in advance!

Actually of the above listed commands only xclock is in xorg-apps .
pacman -S xorg-apps xorg-twm xterm
is needed.

HT204291 Is it possibly to have iTunes music play out of both the computer and AppleTV while using Airplay Mirroring for the TV?

Is it possibly to have iTunes music play out of both the computer and Apple TV while simultaneously using Airplay Mirroring to view the computer screen on the TV? Whenever I try, by clicking on 'computer' radial button for volume in iTunes Airplay, the TV automatically reverts to the Apple TV screen. I usually end up using preferences to 'bring back' the audio to the computert while leaving the picture on the tv, but this means i have to suffer from the inferior sound quality of my Macbook internal speakers.

See:
iOS: Troubleshooting applications purchased from the App Store
Contact the developer/go to their support site
Restore from backup. See:
iOS: How to back up
Restore to factory settings/new iPod
BTW this is the iPOd touch forum

How to darken only one screen in a dual screen setup ??

Hi All,
I have a dual screen set-up probably like many of you and sometimes I prefer to use LR only on 1 screen. That allows me to work on Photoshop or read my emails or whatever else I'd prefer to do on the other screen. My dilemma is when in Lightroom & I press the letter L to darken the screen around my image, for better viewing, it also darkens the other screen that I'm working with. Is there a way to prevent both screens from darkening?? Thanks Ron
PS: Apologies if this has been addressed previously as I could not locate it

Thank you digitaldog, I didn't think so either

Dual-Screen Sessions with Oracle Desktop Client

Dear All,
I have read that the new version of the SRSS and SRWC support dual-screen separation with Windows 2008 R2 sessions, i.e. Windows sessions are able to determine that they are running on a dual-screen device and allow separation as you'd expect on a fat client. Does anyone know if this functionality is available via the Sun Ray software client or if I'll have to invest in Sun Ray 3 Plus devices? Has anyone actually got this working at all?
Many thanks.
Chris

OK. I've applied patch -05 to the SRSS (which is odd because I thought I'd downloaded 5.1.1) which installed without complaint and have upgraded my copy of the Mac OVDC to 2.1.9.
I've run the command (see previous post) and now I can't seem to connect to the SRSS with or without a card - it's not even connecting to the server to get a pseudo session.
What version of the SRSS patching comes with the 5.1.2 download? It's very confusing with the version numbers not correlating. 5.1.1 seems to come with patch -06 but it refuses to install...
Many thanks.
Chris

Is it possible to have multiple different texts conversations with the same two people?

In iOS 8.1.3 is it possible to have multiple different text conversations with the same person? I'm looking for a way to set an old conversation aside to talk about something new.
Is this possible?

speculation is agaisnt the ToS here, but you never know (I was shocked when we got 8 track recording in GB2)
best thing to do is to send Apple some Feedback and let them know what features you want (they really do read what's sent):
http://www.bulletsandbones.com/GB/GBFAQ.html#sendfeedback
(Let the page FULLY load. The link to your answer is at the top of your screen)

ITunes startup reinitializes dual screen setup

Dear all,
as a dual screen setup, I have a MacbookPro7,1 (late 2010 Core2Duo 2,4GHz 13" model, OSX 10.6.6) attached to a NEC MultiSync LCD2690WUXi via DVI-I, using the digital signal flow. I am not using display mirroring. The resolution of the external LCD2690WUXi is 1920x1200@60Hz.
Everything works fine and "as expected" until I start iTunes.
Doing this, both the MacBookPro and the external NEC monitor blank for a short time, as if the MacBook would reinitialize the displays. After doing so, I get the correct resolution on both screens back again, but all windows have now moved to the main screen and decreased in their size, so the dual screen arrangements are lost during this phase. I have to manually put everything back in place, which is highly annoying.
I suspect this behavior might also relate to QuickTime being part of iTunes?
If you have any ideas, please share your knowledge or experience with me.
Kind regards,
Jens

The only solution (well, it's not really a solution, it's a miserable workaround) was to exchange the assingment of the primary and the scondary display, including all the negative side effects you can imagine.
Hopefully Firefox will gain a higher grade of intelligence one day.

I have an older Macbook pro with a dvi output and I want to watch movies on my tv. I have a dvi to hdmi cable but the only image I get on my TV is my desktop background. None of my movie players with appear on the TV screen. What am I doing wrong?

I have an older Macbook pro with a dvi output and I want to watch movies on my tv. I have a dvi to hdmi cable but the only image I get on my TV is my desktop background. None of my movie players with appear on the TV screen. What am I doing wrong?

Hi Maryan,
Open System Preferences > Displays > select the window for you external monitor > click on the Arrangement tab and check the box next to Mirror Displays. It may be slightly different in Lion, but the idea is the same.

Is it possible to have a dual screen setup with an iMac (2012) and an iMac (mid 2007)?

Similar Messages

Maybe you are looking for