Is it possible to mix italic and non-italic fonts in an axis label?

Is it possible to mix italic and non-italic fonts in an axis label in diadem reports?

No, there is no chance to do this.
You can only use the "Textobjekt" to mix italic and non-italic fonts.
Thanks
Klaus D

Similar Messages

7600 / SUP720-3BXL - mixing fabric and non-fabric enabled line cards

Dear All,
I am having to mix fabric and non-fabric enabled line cards on a single chassis.
These are my line cards:
WS-X6704-10GE
WS-X6408A-GBIC
WS-X6148-GE-TX
What's the maximum expected throughput in running with mix fabric line cards ?
Also, what will be the optimal and the recommended switching mode to run (truncated vs. bus-mode) ?
Any inputs will be greatly appreciated.
egards,
ZH

hi!
The maximum throughput will depend on the ingress and the egress card for the traffic. i.e. If the traffic is coming on the fabric enabled card and going out on the same, then the throughput is would be equal to the fabric card ( 20 gbps duplex). But if there is a non fabric card either in the ingress or egress path, then the throughput would be limited by the non-fabric card.
As for the mode to run in, I dont think you would have to worry on that as a fabric card would default to truncated mode where-as the non-fabric cards would run in the bus mode. This works fine, as if the ingress to egress is a fabric card, only the header is sent to the superviser for processing using the tuncated mode and the packet is just sent on the fabric directly to the egress port.
If there is a communication between fabric-non-fabric cards, then the fabric card still uses truncated mode to get the packet processed by the L2/L3 engines on Superviser and then if the egress is a non fabric card, then the packet is sent over the fabric to the superviser. From there the packet is sent to the egress over the bus.

Possible to mix SAS and SATA in S10?

The S10 I purchased has the 146GB SAS drive attached to the LSI controller. I see in the hardware reference manual that there are spare SATA ports on the main board. Can I mix SAS and SATA drives on this machine if I am *not* using them in a RAID array? Does the fact that the SAS and SATA are likely to have different rotational speeds mean that I need to be worried about vibration/stability issues?
Solved!
Go to Solution.

SAS and SATA can definitely coexist. rotational speeds won't matter as the drives are harmonically dampened in their trays. in fact, i have three 15,000 RPM SAS drives sandwiching two 7200 RPM SAS drives in my D10 and can't feel any vibration in any of them. i've also hot-plugged SATA hard drives onto the intel controller with no issues.
ThinkStation C20
ThinkPad X1C · X220 · X60T · s30 · 600

Mixing ssl and non ssl jsp pages.

Hi,
I am new to Weblogic 8.1 and I would like to learn how to setup few jsp pages in https:// and few pages to be served in http:// protocol.
I have created a managed server using 7004 for http and 7040 for https. Currently I have 2 jsp pages index.jsp and test.jsp and both the pages can be accessed using http:// or https://
I wanted to make test.jsp work only with https:// and not work with http:// How do I configure this?
In realtime webapplications. How is switching of http and https working? Are the URL's hard coded in the controller servlet?
Some tips would be helpful.
Uma

Hi,
To do this task do the following,
1. Create a property file in your application. for example let us take myapp.properties
2. include the following to the myapp.properties file
#sslport=7002
#nonsslport=7001
#serverip=127.0.0.1
#ctpath=myApp
# In your case
sslport=7004
nonsslport=7040
serverip=127.0.0.1
# ctpath is the web deployment directory
ctpath=yourapp
3. Create a class to read the property file say PropertyReader.java and implement the following
String sslport=Properties.getProperty("sslport");
String nonssl=Properties.getProperty("nonsslport);
String serverip=Properties.getProperty("serverip);
String cpath=Properties.getProperty("ctpath");
4. initialise the propertyReader class and
in the property class keep following variables in admin session data
String sslpath="https://"+serverip+":"+sslport+"/"+cpath
String nonsslpath="http://"+serverip+":"+nonsslport+"/"+cpath
5. use these variables for ssl or nonssl
response.senRedirect(sslpath+"/bank.jsp"); //for ssl
response.sendRedirect(nonsslpath+"/welcome.jsp"); //for non ssl
like the same way
Regards,
Nishant Kulkarni

Mix Sync and Non-Synced

I have looked and looked, and I cannot find a way to have my music automatically synced to my iPod while manually copying videos.
The main reason for this is that the videos take up way too much space on my hard drive and I'd prefer them on my iPod.
If this is not possible, it would be a GREAT feature to implement in the future.

ok, here's a solution for anyone that's interested:
. create your own lightweight scrollpane class, directly extending java.awt.Container.
. create your own lightweight canvas classm directly extending java.awt.Component.
add the MyCanvas to the MyScrollpane and override the paint method of MyScrollPane to do something like this: (where offscreen is a member variable of type java.awt.Image)
public void paint(Graphics g) {
    if(offscreen == null) {
        offscreen = createImage(getSize().width, getSize().height);
    Graphics og = offscreen.getGraphics();
    og.setClip(0,0,getSize().width, getSize().height);
    //make sure lightweight children of the scrollpane are rendered
    super.paint(og);
    //now draw any overlayed detail over the top
    paintDetail(og);
    g.drawImage(offscreen, 0, 0, null);
    og.dispose();
}took a bit of hunting around to find out how to do it. what i was doing wrong was trying to paint over a heavyweight component (i.e. a java.awt.Canvas), which you can't do, apparently. here's a useful link that I used:
http://java.sun.com/j2se/1.3/docs/guide/awt/designspec/lightweights.html
cheers,
dunc

Possible to mix renderers and editors?

Currently, I have an Accordion with a number of data grids
that contain different information. Items can be dragged from any
of the grids to a common grid outside the accordion, whereby the
drag/drop handler populates the target grid with appropriate data
that represents where it came from.
Here's what I need to do now:
This common grid contains a "quantity" column. Depending on
the type of data that was dropped into the grid, this value may or
may not be editable. When it is editable, it may be limited to a
upper limit that is determined from a data item that was dragged
with it, or it may not have an upper limit at all. I want to render
the current value as a normal number. For quantities that cannot be
edited, clicking on the value should not open it to edit (I have
that much). For values that have a defined limit, I want a numeric
stepper to appear with the defined limits. For values that have no
upper limit, I want a text input field to appear.
How do I approach this?

You'll have to make use of the itemEditBegin event and
manually create your item editor depending on the data. There's
some info here:
http://livedocs.macromedia.com/labs/1/flex20beta3/00000880.html

Some Java 6 quirks (JTable and non-proportional fonts)

Hi,
I just downloaded JDK 6 to check how hard it will be to replace Java 5 on our project. I realized it won't be painless =/
So far, the problems I found were:
1. one of our JTables simply stopped showing its content. It's a two-column table, with plain text cells. Weird thing is that we have much more complicated tables on the application, and they are all fine (detailed investigation still pending, I am just posting first impressions)
2. one of our "reports" is simply a JTextArea with fixed-width font (Courier), so that we can align text at specific positions just by inserting the right amount of spaces. Java 6 antialiased fonts somehow broke this, text can't be aligned anymore. Now, that's weird, antialiasing shouldn't mess with fixed-width fonts, just improve their rendering AFAIK.
Anyone else seeing similar behavior? Any tips?
Regards,
Andre

Create your GUI and start your app on the EDT. Also only do row manipulation on the EDT. Most Swing operations are not threadsafe and must be done on the EDT. If this app worked prior to Java 6, it was only by chance.
In other words:
1. Wrap your main() method's contents in a SwingUtilities.invokeLater().
2. Wrap your addRow(), removeRow(), JScrollBar.setValue() and any other GUI-related calls in a SwingUtilities.invokeLater().
Note that your Thread is so simple that it might be better to use a javax.swing.Timer instead of a Thread. Then your addRow() and removeRow() calls wouldn't need to be in SwingUtilities.invokeLater() since the Timer would only be called on the EDT.

Mixing ECC and NECC (Non-ECC) RAM Modules

Hi,
I have a G5 Dual Core 2.0 with a pair of 512Mb Non-ECC (NECC) RAM installed and I want to upgrade to 3Gb. I'm thinking of getting 2Gb ECC modules and discarding the 1Mb NECC installed. But I came across a phrase in the Apple Manual of my G5 that states "DO NOT MIX ECC and NON-ECC Memory Modules WITHIN A PAIR." Does that mean I can mix ECC and NECC within Memory Banks and NOT within a PAIR? Because in that case I won't have to discard my NECC 1Gb and have a mixed 3Gb Memory!? I'm afraid to actually try it so I would appreciate your insights. Thanks much.
G5 Dual Core 2.0 Mac OS X (10.4.7)

Yes. You can mix ECC and nonECC as long as you don't pair the ECC with the nonECC. The computer will just treat all RAM as nonECC.
You can keep the original memory as long as the two 512MB DIMMs are always paired with each other.

Both blocking and non-blocking io

I'm wondering if this scenario is possible with the new nio classes:
I have a caching server. Clients connect to the server and occasionally send requests for objects. I'd like to use the nio non-blocking APIs to detect that there is a read pending on a socket. However, once I detect this, I'd like to go into a blocking loop to process the request. After this done, I'd like to go back into non-blocking mode and wait for another request.
It seems like this should be possible but the (woefully lacking) documentation isn't clear. Neither is the source code, apparently.
I've got a test case working but I was hoping someone could validate for me that this is support behavior. It's done by waiting for the isReadable() key then calling socket.keyFor(selector).cancel(); and then socket.configureBlocking(true); The reads are then done in blocking mode until the request is done and then the socket is registered with the selector again.
Thanks for any help on this.

I have to ask why you would want to mix blocking and non-blocking I/O.
The only reason you would (IMHO) want to use non-blocking I/O is in a highly concurrent system, to increase the maximum load a system can handle.
The main reason you would want to use blocking I/O rather than non-blocking I/O would be to minimise the latency for a single request.
Unfortunately, the two don't seem to mix together very well... by switching a thread to blocking, you decrease the latency for a single request, but increase latency for the other requests due to reduced resources available. Similarly, by switching to blocking, you are requiring a dedicated thread for that request, so limiting the number of concurrent requests that can be serviced.
That is, it seems to me that using both blocking and non-blocking I/O introduces the weaknesses of both into the system, without gaining much of the benefits of either.
The above aside, the method you gave looks like it would work as you expect, depending on what you are doing with thread creation/delegation. Did your test case work as expected?

Solaris 10 u11 : Is it possible to mix IPMP with vertual network interface

Hi
I have a system with 4 Ethernet interfaces , I'd like to try to have virtual network interface on two of them . then configure IPMP between each two.
- Is it possible to mix IPMP and VNIC ?
- online , I found posts about having vnic on solaris by creating additional interface file (ex, /etc/hostname.bge0:1 ) and also the IPMP create such interface?
- How can I know which IPMP version installed on the system ? and how to know I'm reading the right configuration guide?
- on what basis should i choose the type of IPMP for my system (Link-based or Probe-based)
Thanks in advance
HEBA

Hi.
IPMP can coexist with VNIC.
IPMP - part of Solaris. So you not need check version of IPMP. Just read Docs for Solaris.
http://docs.oracle.com/cd/E23823_01/html/816-4554/ipmptm-1.html#scrolltoc
It's not clear what Vnic you plan use. Is it VLAN or just additional IP on interface ?
For test address of IPMP you should configure interface like bge0:1 with additional options.
Regards.

Can we have xl and non-xl card in one chassis?

Hello,
In cisco document it is mentioned that to work as XL, all card in chassis must be XL (apart from scalable license requirement). Is it a chassis or vdc specific requirement?
In below case we have create two vdcs in one n7k switch and installed the scalable license. Vdc 2 have both mixed ( XL and non-XL) module interfaces whereas VDC 3 have only XL module interfaces
VDC 2-
xl + non xl M-series module interfaces
vdc 3 -
only XL M-series module interfaces
Can anyone please confirm if my below understanding is correct ?
1. VDC 2 will work in Non-mode
2. VDC 3 will work in XL mode.

Hi babu,
You can do this in one view it self.
create a one attribute of type wdy_boolean.. in view context.
Bind these attribute to read only property of table.. and initially set the value to abap_true in wddoinit method.
Then create one button say "EDIT" in view and create action for edit button.. in that action set the above attribute value to
abap_false.
so now, initially table will be in display mode, when you click on edit mode...it will become editable mode...
Hope you got some idea.
Regards
Srinvias

Https site with no mixed content and EV cert is shown as mixed and not identifiying itself

My site https:orderform page contains only https images and website has an EV cert that is valid and current. With history cleared and visiting page for first time Firefox reports that page contains mixed content and that site does not identify iteself.
Hitting F5 to refresh the page address bar correctly shows green with no mixed content popup and that side idenfies itself.
SSLCertificateChainFile has been added and this makes no difference.
Problem does not occur in other browsers (IE, Safari, Chrome).
A new FF profile has been tried but same problem occurs.
Why would refeshing the page work?
Problem affects all firefox browsers 3.5 to 14.01. I dont know about those <3.5.
I have read and tried most suggestions in forum and elsewhere but cant find a solution.
I have not provided the url as this is my order page and its important for me to see genuine visitors.

First a reply to Jsher2000
Thank you for your suggestions. Yes and Yes did this ages ago but no non-https content.
I have found a workaround for what appears to be a bug in Firefox:-(
Here is the non-perfect workaround. First Detect firefox
xUA=navigator.userAgent.toLowerCase()
xFf=xUA.indexOf('firefox')!=-1
if(xFf) top.location.href='https://ord.html'
else top.location.replace( 'https://ord.html' )
The current non-secure page is being replaced with a secure one.
Internet Quote:
"The difference between location.href and location.replace is that the former creates a new history entry on the visitor's browser meaning that if they hit the back button, they can get in a 'redirection loop' which is usually undesirable and may have unwanted side effects."
It appears that FF is using some content (cached) from the previous non-secure page when replacing - leading to the mixed content and non-identified site. An F5 refresh or reload of current page will show that site identifies iteself and there is no mixed content.
In summary its a Firefox Bug.

Mixing anamorphic and letterboxed footage

Is it possible to mix anamorphic and letterboxed DV footage in Final Cut?
I have a project that was shot on both formats.
How should I proceed?
Thanks.

And, if I need to, can I convert the final video to true 16x9 anamorphic, so it'll play full screen on a 16x9 monitor or theater screen?
Yes, but it will look like crud. This question gets asked a bunch so there are lots of responses out there explaining why this will be the case.
Oh, and if I need to convert the whole video to 4x3 full screen for intranet distribution, is it possible too? Thanks.
Yes, cropping and/or reducing the size for internet or intranet distribution can be accomplished using Compressor or QTPro.
Good luck.
x

Mix formCalc and javascript in same event?

Hi Folks,
I have a bunch of formCalc and Javasript I'm trying to merge (two different forms, different programmers). Is it possible to mix javascript with formCalc in the same field event? If so, how?
thanks!

No, it is not possible to mix FormCalc and JavaScript in the same event. You will get run-time errors.
Steve

Mixing music and audio books

Is it possible to mix music and audio books on the same iPod and yet shuffle the music but not include the audio books when playing? If so how do I do it?
New long battery life NANO
Windows XP

You can right-click on an audiobook, choose Get Info,
and checkmark "Skip when shuffling" on the Options
tab. This is not necessary on true audiobook files
(.aa, .m4b), as those are skipped automatically, but
it's useful for mp3 files.
As my 4 year old dog used to say, "Well, I knew that!"
Thanks Craig!

Is it possible to mix italic and non-italic fonts in an axis label?

Similar Messages

Maybe you are looking for