Issues with 3845 Router

I have a 3845 Router that my company just purchased. Once I log in, it says the SDM is installed on it, but I cant enable SSH on it. (2), When I configured it via the console, it did prompt for enable password, but since i took it to a region, it does not prompt for enable password again, it simply takes me to the enable mode, with the username password. I configured the enable password as ********, but it does not prompt for it. Can any one help me with these two issues? Thanks in advance.

RICK,
Thank you very much for your prompt response to my request. Pls find below the reports of the various "shows" that i performed.
Cisco IOS Software, 3800 Software (C3845-IPBASE-M), Version 12.4(3g), RELEASE SOFTWARE (fc
2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 06-Nov-06 05:34 by alnguyen
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
ROUTER uptime is 22 hours, 33 minutes
System returned to ROM by reload at 01:06:07 UTC Wed Mar 17 1993
System restarted at 01:06:57 UTC Wed Mar 17 1993
System image file is "flash:c3845-ipbase-mz.124-3g.bin"
Cisco 3845 (revision 1.0) with 222208K/39936K bytes of memory.
Processor board ID FCZ110471QE
2 Gigabit Ethernet interfaces
4 Serial interfaces
4 Channelized E1/PRI ports
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
62720K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
#show crypto key mypubkey rsa ?
% Unrecognized command
#show crypto key mypubkey rsa
^
% Invalid input detected at '^' marker.
#sh line vty 0 15
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 450 450 VTY - - - - 23 2 0 0/0 -
451 451 VTY - - - - 23 0 0 0/0 -
452 452 VTY - - - - 23 0 0 0/0 -
453 453 VTY - - - - 23 0 0 0/0 -
454 454 VTY - - - - 23 0 0 0/0 -
455 455 VTY - - - - 23 0 0 0/0 -
456 456 VTY - - - - 23 0 0 0/0 -
457 457 VTY - - - - 23 0 0 0/0 -
458 458 VTY - - - - 23 0 0 0/0 -
459 459 VTY - - - - 23 0 0 0/0 -
460 460 VTY - - - - 23 0 0 0/0 -
461 461 VTY - - - - 23 0 0 0/0 -
462 462 VTY - - - - 23 0 0 0/0 -
463 463 VTY - - - - 23 0 0 0/0 -
464 464 VTY - - - - 23 0 0 0/0 -
465 465 VTY - - - - 23 0 0 0/0 -

Similar Messages

Issues with second router disconnecting and reconnecting

My second wireless router keeps disconnecting... it reboots then becomes availble after a minute.
The second wireless router is a Netgear WNDR3400v2 and is connected to a Actiontec MI424WR via an ethernet wire. I changed the settings as noted in a forum post to hook up a second router... the setting changes fixed the issues with IP address conflicts that I was having. The issue is that the Netgear router keeps disconnecting. The Actiontec router never disconnects.
There are 16 devices connected to the internet.
Parts of my house don't get a signal from the Actiontec router.
Please let me know if you have any suggestions on enabling more wireless coverage throughout my house from my Actiontec router and/or how to stop the Netgear router from disconnecting. I can't find any specific information that isn't confusing.
My Actiontec router is on the main floor in a cabinet, which prevents the signal from reaching to parts of the house... there is an ethernet cable that runs from the cabinet to a room upstairs, which is where the Netgear router is located... that signal reaches most of the house.

Hi Clueless777,
Most likely if your Netgear router is randomly disconnecting but the Actiontec is not, it's going to be an issue with your settings in the router. There is a post over at http://www.dslreports.com/faq/12506 that will tell you exactly how the settings should be in both routers for this to work properly.
As to increasing the signal from the Actiontec router, a couple of things come to mind but you may have already did these things. First, make sure to change the wireless channel in the Actiontec to something like 8. Also, make sure that no cordless phones are located nearby the Actiontec router as much as you can. We mention this because many cordless phones operate in the 2.4ghz range which is the range of most WiFi routers and devices. You could also look into getting a range extender but I wouldn't recommend it because your Netgear router is essentially doing the same function without sacrificing service. Other than these suggestions, take a look at the link above and make sure your settings match. That should help you out more so than changing the channel in the Actiontec router and/or relocating cordless phones.
We hope that this helps.
CJ

Issue with Linksys Router and Modem with Vonage Device

Hello,
I have a Linksys Router and Cable Modem. Plus I have Vonage for my home phone. I have been having several problems and now, my Vonage phone will not work at all. I have cable internet and my ISP is Cox Commuication. I do not know how to connect my Vonage device with my Router and Modem. People have been giving me advice, but nothing has worked.
Does anyone know how to intergrate all three of these items together? Basically which plug goes where. Currently my phone is not working. The only thing that is in use right now is my linksys cable modem. I have the power cord plugged in, the blue cord from the modem plugged into my laptop, and the cable from the modem to the wall jack. Please help. Thank-You!
Linksys Router: WRT54G version 6
Linksys Cable Modem: BEFCMU10
Vonage (Motorola): VT2143-VD
Message Edited by preshe79 on 03-16-2008 03:56 PM
Message Edited by preshe79 on 03-16-2008 03:58 PM

The router should be online first. Can you get into the router's configuration page?
The box said windows xp or better... So I installed Linux!

How can I resolve a NAT config issues with Arris router & AE

I'm having NAT conflict issues. None of the existing threads on the forum match my configuration. I have an Arris Cable Router/Modem (Time Warner) with 4 ports. Port 1 feeds an unmanaged switch for ethernet connected devices, and port 2 on the Arris router feeds and Airport Express. Getting "Double NAT Status" on airport utility for the AE. How can I resolve this while not effecting my wired devices ? Thanks so much !

To resolve the NAT conflict you simply need to reconfigure the AirPort Express as a bridge.
You would do so using the AirPort Utility, as follows:
Run the AirPort Utility, and then, select the AirPort Express.
Select Edit.
Select the Network tab.
Change Router Mode to: Off (Bridge Mode)
Select Update and allow the Express to restart.

Xbox WiFi Connection Issue with Xfinity Router DPC3941T

Hello, I am unable to connect my Xbox 360 (slim) to our Xfinity modelm/router model DPC3941T. The SSID for each band (2.5ghz and 5.0ghz) is enabled, however, the xbox console is unable to detect. I have tried the following:-resetting network settings on the xbox console-restart modem-configure manual wifi network (trying each band) but get an error unable to connect to network I have spent some time scanning through these forums and others via Google search, but I only see many older posts related to different model routers. Is anyone familiar with this wi-fi connection issue using an xbox 360 and DPC3941T? Please assist thank you!

Hello, I am unable to connect my Xbox 360 (slim) to our Xfinity modelm/router model DPC3941T. The SSID for each band (2.5ghz and 5.0ghz) is enabled, however, the xbox console is unable to detect. I have tried the following:-resetting network settings on the xbox console-restart modem-configure manual wifi network (trying each band) but get an error unable to connect to network I have spent some time scanning through these forums and others via Google search, but I only see many older posts related to different model routers. Is anyone familiar with this wi-fi connection issue using an xbox 360 and DPC3941T? Please assist thank you!

Solution for loss of DHCP with Win7 Home Group issues with FIOS Router

Apparently the FIOS Router (Westell 9100 in my case) doesn't like the IPv6 that Homegroup uses. I lost DHCP service on all three computers that have Win7 installed. I could manually set the IPv4 addresses in the Network Connector options on my computer and every thing worked fine. If I tried to use DHCP for IPv4 I wound up with a private network address (169.xxx.xxx.xxx).
DHCP for IPv4 worked fine adfter I disable IPv6 and the associated topology services. I also removed the HomeGroup option from our network setup.
If you want to use home group be prepared to manually set the IPv4 addresses in your network devices.
Good luck

Interesting, thanks for posting.
Are these Windows 7 PCs that you installed 7 onto yourself, or ones that came with it? I have an HP laptop that came with Windows 7 already installed, no issues at all about IPv6 that I know of. IPv6 is still activated, works just fine on my FiOS Actiontec router, but maybe the Westell is just enough different to be sensitive to that.
Strange.
Justin
Verizon FiOS TV, Internet, and phone
QIP6416-P1, IMG 1.7C, Build 09.83
Keller, TX 76248

Having terrible issues with WRT54G Router

For a long time our router worked just fine, but in the last few months its really deteriorated, and as of today, it won't work at all.
I thought that perhaps updating the software would make it run better, so I came to this site, and saw a download for the firmware for the latest version (Mine is only running a 6.0) but when I try to download the upgrade, it says that it's a BIT or BIN file (I think BIN) that my computer can't open, would I want to search the web for a program that will run that file. I try that - nada. Nothing will work becaues of the type of file, and I have no choice in types of files to begin with.
I've unplugged everything and replugged in the correct order countless times. When I don't use the router at all, my computer just conncted to my modem works just fine. But add the router, and neither computer works.
Please oh please help me....I don't really know too much about what I'm doing, but I'm a quick learner!

Hello Brooke,
First, version 6.0 is actually a hardware version for a WRT54G.
The firmware refers to the software driving the router to run.
You can find your router's firmware version in your router's setup page.
Click HERE on how to open your router's setup page.
Second, a firmware file is not executable.
Meaning, you do not have to open it or run it.
Leave it saved on your computer after downloading it.
And then, click HERE for steps on upgrading the firmware on your router.
Hope this helps!

Multiple vlans configuration issue with RV016 router and SG 300-10MP witch

Hi,
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
Router (RV016 10/100 16-Port VPN Router) as gateway mode:
IP : 172.16.0.1/24
DHCP Server :
IP : 172.16.0.2/24 GW: 172.16.0.1
2 subnets :
172.16.1.0/24 GW: 172.16.1.1 to serve vlan 1
172.16.2.0/24 GW:172.16.2.1 to serve vlan 2
Switch (SG 300-10MP 10-Port Gigabit PoE Managed Switch) as layer 3 mode:
IP 172.16.0.254 (vlan 8 default)
Vlan 1 : 172.16.1.1
Vlan 2 : 172.16.2.1
1 device connected on each vlan
a workstation on the vlan 1
a laptop on the vlan 2
In this scenario (see the attached pdf file) the DHCP server is connected on a router, hosts on vlans dont receive any IP address.
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.
I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration ?
I hope the explanations are clear enough and my English too
Any help will be highly appreciated,
Zoubeir

Hi Eric, the small business group doesn't support the ASA config, but I can help with the switch.
A couple things I notice in your description-
48 port (192.168.1.254) and the other 24P (192.168.1.253) we have a second vlan 20 set up on the 24P switch (192.168.2.253) we have ports 1-12 set for vlan20 (untagged and trunk), the remaining ports on on the default vlan 1.
The connection between the switches, is it 1u, 2t?
The link between the switches should be 1u, 2t, the switches support the trunking and vlan tagging, meaning all communication will work fine.
We have the 24p and 48p switches connect using GE1 and GE1. We are unable to ping a device on vlan 20 ( on the 24p switch
The 24p switch should be in layer 2 mode, if you have the 48 port l3 switch upstream. Additionally, you need to have the default gateway set on the 24p switch.
We have a static route set on the 24p switch (0.0.0.0 192.168.1.0).
Between the switches, it shouldn't require any static routes, assuming you correctly trunk / tag your ge1 ports, with both switches operating in l3, the ip route table dynamically builds the connected routes, therefore a static route is redundant.
-Tom
Please rate helpful posts

Having issues with WRT54GS router acquiring network address after wireless connection.

I've been experiencing problems acquiring a network address after making a wireless connection with the WRT54GS wireless router. I have a Comcast cable modem connected to the internet port of the router and after configuring the SSID and the 64 bit WEP key, I can connect to my router's SSID, but since I can't get an IP address, never connect to the Internet. I've already cloned the laptop's mac address to no avail. Even after configuring a static IP address, subnet mask and default gateway, still cannot connect. I can Ping and Traceroute from the router but not the PC. I can ping localhost and host IP address from the laptop but not the default gateway. Any suggestions would be appreciated. Thanks, SJ

Connect the computer to the router with the Ethernet cable.
Try to access the internet when you connect the computer to the router with the Ethernet cable.
Open the setup page of the router and go to Status page. Check the Internet IP address on the status page of the router.
If you are able to access the Internet with the Wired connection to the router then try to create a new wireless network on your router.
Open the setup page of the router and go to Wireless tab. Change the wireless network name SSID and change the channel to 11. Save the settings. Go to Wireless security sub tab and check the wireless security settings. Click on Wireless MAC filter sub tab and make sure that it is disabled. Click on Advanced wireless settings sub tab. Change the Beacon Interval to 75, RTS and fragmentation threshold to 2304. Save the settings.
Try to connect to the new wireless network and see if that works.
How many wired and wireless computers do you have in the network?

Issues with new router

Had to change modem/router unit due to Comcast upgrade. My HP p1102w is not recognized on the new network.
I tried the instructions from my original package - smart install. Smart install did not start up as described when I plugged printer into PC. Following backup instructions (which always suck), I used the original CD to attempt a setup. No such program as ssis.exe for setup included. Also no EXEs that would start without error "invalid string". Love those informative errors.
So I decided to uninstall and reinstall the software.
Got partway through, was informed there is a print job pending on the printer, so cannot uninstall the printer. However, the printer no longer shows in Control panel, so I can' access the print queue to clear the jobs
OS is windows 7. I am fairly savvy and have tried the usual suspects. Anybody got the magic decoder ring to remove the install and re-install, hoping to detect the new network?
Ready to dump HP products and find something that actually works.

Hi @gwandsh ,
I see by your post that you are having issues setting up the printer over the new network upgrade. When trying to uninstall the software, it shows a job stuck in the queue and won't let you uninstall the software. I would like to help you out today.
If the Print Spooler isn't running the printer icon won't show in the Devices and Printers. If that isn't the issue we can delete the spool folder to resolve that issue.
How to Clear Current Print Queue In Windows Vista & Windows 7.
You shouldn't have to reinstall the software though to configure the printer over the new network.
Just reset the printer to clear out any previous network settings.
Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
Print out a configuration report and make sure the SSID and IP address are cleared.
Printing a Configuration Page.
Verify your Encryption and Password for your network.
How to find your wireless network password.
Connect the USB cable from the printer to the computer, if it isn't already.
Then run the Wireless configuration to setup the printer on the network again.
Go to Start, All Programs, HP, HP Laserjet P1102w, then select Wireless Configuration.
(if the software isn't listed, run the CD for the printer to install the printer software as a USB connection)
Run through the steps to configure the wireless.
Then disconnect the USB cable.
Test the printer over the wireless network.
If you need further assistance, just let me know.
Have a great day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Outlook send issues with Linksys router

I am on my brother's Linksys router with my own laptop. I can't send email from Outlook 2007, but I can receive it. Any ideas?

Make sure that under Outlook send receive settings ..... the Outgoing Mail Server ... should be in the form of .... mail.Domainname.xyz .... the same as in Incoming Mail Server ....
Click on More Settings and select the Outgoing Server Tab....
Check My outgoing server (SMTP) requires authentication......
Use same settings as my incoming mail server.....
Click Ok. Click Next. Click Finish
See if the Outgoing Mail is working or not ....

Issue with 2wire dsl router when connecting power pc g4 via ethernet

Issue with 2wire dsl router when connecting power pc g4 via ethernet. The 2wire will keep resetting. When I connect my macbook pro via ethernet to the 2wire all is ok, but as soon as i connect the power pc. . . .reset. I have emailed 2wire support. They recommended using a different patch cable. Tried that.. .. anyone else having this issue???? Any help would be appreciated. . .

Search the discussions for issues with 2wire dsl routers. This has come up before in a discussion I've been involved with, but probably not to do with the MDD. I do remember it being a design issue with the router, something that was done to it before dispatch.
Let us know if you can't find it and we'll have a look.
If you afford it, bin the 2wire and go buy something decent like a Netgear.

IChat issue with Siemens SE567 Router

I have just signed up with a new ISP and they insist I have to use the Siemens SE567 router. It works fine for the internet most of the time, but I can not do screen sharing or video chat. The strangest thing is I could do both with my last ISP the only difference now is the router and ISP. I have tried all different configurations and been on tech support with both Apple and my ISP to not avail. Anyone else having any issues with this router?
Thanks,
Pam

Hi,
I am not sure if this was you I was Texting to yesterday (20th).
I linked the person to the Port Forward site
Their Set up pages were blue and white as opposed to this grey and Orange.
They were set to UPnP and NAPT as it is called on this device had no ports set.
The Computer was using Tiger with the Firewall Off.
Stealth (Ping Blocking) was also Off
We tried calling from both ends.
The result was an Error 7 at the Siemens end until we made sure the Quicktime Setting was done.
A second computer that had no camera had iChat turned Off to prevent any confusion about IP addresses.
The User did not think the ISP Offered VoIP and had no Vonage device (an issue with ichat 2 and 3)
My Error 8 log did not identify that the far end was using Tiger and iChat 3
(Should list port 5060 as SIP port)
Firewall in the Siemens was set to Low.
DMZ was Off.
There seem to be no Ping Blocking (Not that the log got that far) or DoS or SPI settings.
File Sharing in System Preferences > Sharing is not an issue in Tiger so not checked.
From reviewing the Chat I can see I did not check if System Preferences > Quicktime > Streaming was at 1.5Mbps
If you have to change this and iChat is Open restart iChat.
Also in the Firewall on the Mac in the Advanced Button is Block UDP Connection Active ?
IF so it will need deselecting as most of iChat's A/V Stuff is on UDP.
The Port Forward set of Pic suggest that the one they had was Branded for Telus as an ISP so it could be that this has slightly different software/firmware.
I suggested posting here as I had run out of iDeas on this device.
8:09 PM Thursday; January 21, 2010
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

Internet connectivity issues with SA 520W router

Hi,
We have configured Cisco Small Business Pro (SA 520W) in a small office and all computers are connected with wifi. We are facing following problems:
1. Computer is connected with network and 100% signals available but there is no internet. After repairing network from computer or sometimes rebooting computer fix the this problem. What cause internet connectivity problem?
2. Sometimes computer is connected with internet and everything work fine but suddenly there is no internet. May be internet come back again after 2 minutes etc. Strange behavior.
3. Sometime there is no internet connection even after trying all possible tuneing but internet connection become alive again if we reboot router.
All these problems appear randomly on different computers. Can anyone tell what's the reason of all these problems and how can fix it?
Thanks.
Sajjad

I have the just similar problem since few days , for long time I have no issues with wireless router
I have five static IP addresses I am using 1 static IP for the Router and other for the internal use
I though it was my inter provider technical issue,
The internet is working through provider gateway router but not through a Cisco SA520W
some times it works some time it wont resolve host name, internal LAN works perfect ,but internet drops packets and it is very slow
If we dynamically setup the router, it works but not for the static IP address
my old configuration is not saved , reset to factory defaults even then it did not work
I do have 24 port cisco switch when I login there is no gui console just blank blue screen with text boxes
I appreciate some can guide.
I believe we need the update firmware on both devices .I appreciate for the help
Thanks
Ravi

More issues with 7.4.1 & 7.4.2 - help needed : tried the usual fixes.....

I have the dual band 2.4 or 5GHz model AEBS, Belkin powered 4 port hub, Canon IP1600 printer, 40GB & 120 GB HFS+ USB drives. Win 7 64bit & XP machines.
I only 2 weeks ago did the FW upgrade.
With prior to these 2 FW's, i had issues with my printer not printing the whole page, it would always cut mid last line and then freeze. Had to cycle the printer to get the page out. It would not necessarily print the 2nd time either. The HDD's going through a hub worked fine. I updated to 7.4.1 hoping that would fix the printer issue, it did not. I then began getting "disk repair needed" on both HDD's over the next week; culminating upon both HD's going corrupt.
I reformatted both and moved all my music/movies back, and all was good for a week. Then today, turned both drives on at different times, and both need disc repair again.
So i unplugged them and hooked them up to my Linux Mint rig, and there was no apparent corruption, and all the files were playable.
SO I updated to 7.4.2 tonight, and the printer issue is still happening. BUT the 2 HDD are just fine now, after the update....so this leads me to think there was/is an issue with the router? Oh, i tried to directly plug the HDD into the router as well b4 the most recent update but still disc needs repair....of course they have been working fine for the last 2 hours...
Anyone have any ideas? Im ready to pull my hair out...Thanks in advance.
Message was edited by: user2009

Hey Chris, thanks for responding, in my above post I mentioned my troubleshooting:
Since updating my iPhone 5S (T-Mobile) to both 8.0.1 and then 8.0.2 I've had more issues than I've ever had with any iOS in the past (with the exception of iPhone 4 running iOS 7, but clearly that is an older phone, not a 1 year old model like the 5S). Have tried resetting, powering off, etc too by the way.

Issues with 3845 Router

Similar Messages

Maybe you are looking for