J5750 Continuous "Remove and re-insert left cartridge" message

Installed a new HP black 74 cartridge on right side and the printer printed out the "align cartridge" sheet. But then a "Cartridge error: Remove and re-install left cartridge" message came up. The error message just continues, even though I have removed and re-installed the left cartridge repeatedly, I have cleaned the electrical contacts per manual instructions, and I have rebooted the whole printer.

If the printer model with the issue is the PSC 2170 you mentioned in a previous post the document here may help resolve the issue. Clean the cartridge and printer contacts as shown in step five and six.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

I frequently have to remove and re-insert the SIM in order to access the internet. Has anyone else experienced this problem? Is the issue with the IPAD or the SIM card?

I frequently have to remove and re-insert the SIM card in order to access the internet. Has anyone else experienced this? Is it a problem with the IPAD2 or with the SIM card?

Could be the SIM card, the iPad, or both.
Start with replacing the SIM card.

Poor print quality until I remove and replace each toner cartridge

I have an interesting situation that seems to have manifested itself recently. This is pretty reproducible.
The printer is in sleep mode
A color job is sent to the printer and the resulting print has no color and faded black and white
If I open the front panel and remove each cartridge, not even fully remove, and replace with itself, the color and quality is perfect.
Calibrating, diagnostics, etc. have not helped. Printing of the diagnostic page, or color bands, etc. yield the same results.
The paper comes out warm as it always has. The toner doors all open.
So, any ideas? Next steps to try?
Thanks,
Paul

Hi justviewing911,
Try doing a Hard Reset as described in the following link. Click Here Does that help?
Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
Please select the "Accept as Solution" button on the post that best answers your question.
I appreciate your input ! ___________________________________ _____
Thank You,
Rich
Expert

Treloaded. Getting a message "iTunes not installed correctly" Error 7 Windows Error 998. Removed and retried install got same message??????

Trying to install iTunes on my XP machine after the operating system was reloaded. Getting a message "iTunes not installed correctly" Error 7 Windoes Error 998. Removed and retried installgot same message??????

This can sometimes indicate that one of the other itunes-related software components is damaged. (Usually Apple Application Support, but there are other possibilities beyond that.)
Perhaps first try a complete uninstall/reinstall as per the following document:
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
Does that get you past the 7?

HT1926 i had itunes on my pc for a number of years. worked fine last night even. today, nothing, screen gave error 7, windows error 126, tried removing and re-installing, still same message. says I am missing MSVCR80.dll

I have had Itunes on my pc for years. Worked fine last night. Today it gave me a message missing MSVCR80.dll, tried reinstalling, didn't work. Removed Itunes completely, reinstalled. Didn't work. Same message. Any fix ideas?

Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99196)

Officejet 7410 shows "Remove and check color cartridge" on display.

I have removed and checked the Color Cartridge and replaced it. No change.
I carefully cleaned the cartridge contacts with distilled water. Still no change.
I went and bought both a new Color Cartridge (#97) and a new Black Cartridge (#96).
Installed the new Color Cartridge. Still no change.
Tried changing the Black Cartridge as well. Still no change.
I carefully cleaned the cartridge contacts and printer contacts for both of the cartridges with distilled water. STILL no change.
So, after spending close to $100, I still can't use the printer.
Does anyone have a solution to this problem?

I know this thread has been around a while, but I figured out a solution last night when I had the exact same "Check color cartridge" error message stuck on my HP7410. I found someone else online with a different problem on a different HP printer, who used a very similar repair procedure as listed here, but with one extra step. I figured I had nothing to lose, so I tried it and it worked, though you have to reenter the current date/time and your network info, because it wiped out the memory and went back to factory settings. So...
1) Unplug printer power cord from printer.
2) Hold down the # and 6 key while plugging printer cord back in. Continue to hold those keys down until printer says SEMI FULL RESET (it doesn't give you any other choices, and it does NOT say SEMI-NVM (non-volative memory RESET - I don't know how to get that) so just wait til SEMI FULL RESET comes up).
3) The printer will then turn off by itself.
4) Turn the printer on.
5) The printer will want you to set language, but don't do it yet.
6) Press the * and # key at same time.
7) Press 124. You will see "UNDERWARE: and a series of letters and numbers."
8) Press the right arrow to scroll through all the possible system setting categories once, and hit OK.
9) Scroll through them again to set the language, change the day/time and re-enter your network settings (network name/ID and password) and I suppose anything else you need to do, like set fax settings.
It's possible you may need to power off and power on again between steps 8 and 9 - sorry, can't remember if I tried that but I don't want to do this again and risk messing anything up.

Developer walkthrough fails on Continuous MEasurment and Logging

I am having problems watching these two videos:
Developer Walkthrough of the Continuous Measurement and Logging Sample Project
http://www.ni.com/video/2741/en/
Developer Walkthrough of the Continuous Measurement and Logging Sample Project
Queued Message Handler Template Documentation
http://www.ni.com/video/2728/en/
It gets stuck at the start saying Slide 1/1: Buffering.
I have downloaded the latest Adobe flash. A guy from NI support rang in response to my question to them and said that it worked on Chrome for him. I tried that and they don't work for me.
Can anyone help?

OK, one update from my side:
On my machine (Win7, 64bit) it is working when running Firefox 29.
Using IE9, the link to the video seems to lead back to its page, no popup, nothing.
Point is, that my IE (since IE8) is obviously not 100% compatibel with Adobe Flash player. For instance, i have issues to play videos from YouTube on the machine using IE (error messages like Flash not installed or simply a blank screen instead of the video) but not for all videos there. With Firefox, i can view all videos from YouTube except the ones which are prohibited from YouTube due to national restrictions ("This video is forbidden in your country" or something like that).
So all in all, it seems to me that the issues you all observe are issues between the browsers and Flash, invalid settings for popup-blockers and specific "error handling" of specific browsers (which create the "loop-link-behavior").
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Incompatible cartridge message

incompatible cartridge message started on HP 4500, relaced both HP cartridges, couldn't clear. Bought a new 4630 with fresh HP cartridges, and when I powered it up before running setup, incompatible message reappeared. Uninstalled 4500 from control panel, ran 4630 setup and still getting incompatible cartridge message.Help!

Hi @soie,
Welcome to the HP Forums!
I noticed that you are getting the incompatible ink cartridge error with your HP Photosmart c4780. I am happy to help!
Most likely by the description of your post, this printer is setup for the European Market, instead of the U.S. Market, hence getting this error message. You can try going through this guide, HP Photosmart C4600 and C4700 All-in-One Printer Series - A 'Cartridge Problem,' 'Cartridge Failed,'....
If the guide does not solve your problem, please call our phone support at 800-474-6836 for further assistance. If you live outside the US/Canada Region, please click the link below to get the support number for your region. Country-language selector.
Hope this helps!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

My hp psc 2210 gives message remove and check cartridge, i did, there is nothing that looks wrong,

I look inside around wehre the cartriges go and didn't see any loose springs etc. If i remove the left cartridge, it still gives the same message, if i remove the right catridge, it tells me to insert the right cartridge.
The only function that I am able to do is scan using the comptuer. (not able to copy or fax, or print)
When this message first occured, the printer made a clunking noise, That noise, does not always repeat when attaching the power cord, but the message always is present.
Appreciate any help you can provide.
the ink cartridges are farily new and full and hp.
the id's on the printer are:
MY310F75DX
C8654A
IC 4660-Pl5MO201
C8654-00019
the id's on the cartridges are:
22 Tri Color
2011/09/05 S
L10 2 14:45:14
21 Black
2011/09/08 Y
L05 1 06:59:20
Thanks
Ashwin1980

Remove the right cartridge and clean the contacts on the cartrdige and printer as shown in this page. If that does not correct the issue you will need a new cartridge, check the warranty for your current cartridge as shown here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

"Remove and check cartridge" error message

My Dell Latitude died. It was hooked up to my hp psc 2110 all in one printer.
After completing the set-up basics on new laptop, I downloaded the drivers for the printer successfully. A test was successful.
Next day, I tried to print. The printer told my laptop that the ink was low. Installed new cartridge; hit enter to align. It went all the way through alignment, but would not print. Instead it posted the scrolling message “Remove and check cartridge”.
I removed and reinserted the cartridge and nothing changed. Same message.
Expensively (I really needed to print), I inserted a new cartridge. The printer started to align the cartridge. At the second bar it froze. I watched the two unchanging bars for twenty minutes.
Since then (in this order) I have:
Turned off the printer for ten minutes and turned it back on. It started scrolling (?) “Remove and check
          cartridge”
Uninstalled then downloaded the drivers and tried all again.
Left everything off for forty-eight hours.
The troubleshooter from the computer couldn’t identify the problem, but said the toner was fine.
I could not print a self-test report because no matter what button I push nothing changes.
Opening and closing the top section (in order to replace cartridge) makes the cartridge move, but does
               nothing to the message.
http://h20000.www2.hp.com/bizsupport/TechSupport/SupportTaskIndex.jsp?lang=en&cc=us&taskId=1
               10&prodSeriesId=295848&prodTypeId=18972&supportTaskId=42089 does not have this error
               message
Looked at and tried all suggestions on HP forums.
The three little green lights (best, normal, fast) flash together.
It still only scrolls “Remove and check cartridge”.
I have not hit it.       I am out of ideas.           I cannot afford a new printer.
PLEASE HELP.   (Please keep it clear and simple.)
hp psc 2110 all-in-one printer · printer · scanner · copier MY342F5744    C8644A   Made in Malaysia
        (inside:   MY342F5744    C8644-60002)
Windows 7
Toshiba Satellite L770
Thank you.

I, too, gave up, and purchased a new cartrige. At least for me it did the trick.

Need to bypass "Remove and check color cartridge" error message

I have an old HP printer giving me the error message "Remove and check color cartridge." I remove it, it's good, I put it back, same message. I try leaving it out, I get an error message asking me to install a color ink cartridge.
I DON'T EVEN WANT TO PRINT WITH THIS PRINTER. I have a new HP printer connected to my wireless network that I use for all my printing. I am using the old printer for its scanning capabilities in my crafting area. I am JUST wanting to scan old pictures to an external hard drive for storage, so that I don't have thousands of print photos sitting around in boxes and files.
Please help.

I had the very same problem with my HP Officejet 7410 so cleaned the ink cartridge and carriage contacts per the directions listed on this link:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01423559&tmp_task=solveCategory&cc=us&dlc=en&la...
After my first attempt at cleaning these contacts, i reinserted the cartridge and tried printing again but I got the same error message. Next I removed both cartridges (color & black) from their slots and after pointing a flashlight at the carriage I discovered the bottom of the carriage was covered with ink, so....using over a dozen cotton swabs I cleaned the bottom of the carriage as best i could. Also, thinking that perhaps the ink cartridge was not manufactured exactly to its proper size and shape, when i inserted the cartridges back into their slots I slightly pressed them in to be sure the contacts would touch.
I was happy to see that now the error message is gone and my printer is printing again....well, at least for now.

1600 all-in-one series printer error message to remove and check color cartridge will not go away

Error message, remove and check color cartridge will not go away even after replacing cartridge (same refilled). Any help would be appreciated.

I had the very same problem with my HP Officejet 7410 so cleaned the ink cartridge and carriage contacts per the directions listed on this link:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01423559&tmp_task=solveCategory&cc=us&dlc=en&la...
After my first attempt at cleaning these contacts, i reinserted the cartridge and tried printing again but I got the same error message. Next I removed both cartridges (color & black) from their slots and after pointing a flashlight at the carriage I discovered the bottom of the carriage was covered with ink, so....using over a dozen cotton swabs I cleaned the bottom of the carriage as best i could. Also, thinking that perhaps the ink cartridge was not manufactured exactly to its proper size and shape, when i inserted the cartridges back into their slots I slightly pressed them in to be sure the contacts would touch.
I was happy to see that now the error message is gone and my printer is printing again....well, at least for now.

Error message: "remove and check cartridge on right." photosmart 2610

I installed two brand new HP cartridges (color and black) in my Photosmart 2610 all-in-one about 1 month ago and they were working fine but now I get an error message asking me to "remove and check cartridge on right." When I check the cartridge (black), it looks fine but the error message won't go away and the printer won't print. Suggestions?

I had the same problem, I have tried resetting with #6 or #3, cleaning.
What worked for me:
1 - While printer is on, go to the "Mfg Commands"
(on my printer I had to press "*" and "#", others would need to press both left and right arrows, etc.)
2 - You will get the following message "Enter special key combo", then enter "123".
3 - Press the right arrow until you find "Special Reports", click OK
4 - Press the right arrow until you find "Print Cartridges", click OK
What was my surprise when at number 3, it started printing !
And then, everything came back to normal !
Super cool !
Hope this works for you !

My photosmart 2610 has an error message "Remove and check cartridge on right"

I have replaced both the black and color cartridge and still have the error message. Also have restarted computer and turned printer off and on several times. Need help!

Hi ruf,
Check this article and see if this can fix your printer - Remove and Check Cartridge
Hope this works for you!
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Cheers!
* If this post has helped you, the White Kudos star on the left is a great way to say thanks!
* Please mark Accept As Solution if it solves your problem so other users can benefit as well.

G85 printer says "remove and check color cartridge"'

My G 85 all in one inkjet printer was working fine until it suddenly displayed "remove and check color cartridge". Now it won't print. I removed both the color and B/W cartridges and cleaned contacts on printer and on cartridges. After re-insertion same message. Removed color cartridge and installed a new color cartridge. Same message is displayed. Any help would be greatly appreciated.
Phil

Hi saratogaphil,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I see that you are having some issues with an error on printer to Remove and check Cartridges. I have a few different document for you to try. Please click on the following links for Print Cartridge Errors.
You can also attempt to clean the product with the use of the following link on Cleaning the All-in-One as well as Maintenance and Cleaning.
Once last step you can try is Resetting the Printer.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thank you for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

J5750 Continuous "Remove and re-insert left cartridge" message

Similar Messages

Maybe you are looking for