Jabber for Windows 9.0.1 phone control of Cius?

Can the Jabber for Windows client control a Cius like it can a 79XX phone?

Jabber for Windows 9.0(1) will not be posted automatically for all customers.
An internal communication will be issued to all internal CSM's and PSM's in the next couple of days explaining the exact procedure for requesting access to the client and how to raise the ops request to make it available for the customer org in question ... so reach out to the your Partner manager to understand that procedure and to enable access for your customers.
Regards,
John

Similar Messages

Jabber 10.5 for Windows + App Dial Rules + Phone Control Mode

I am using all 10.5.
I have Jabber for Windows integrated with Outlook. I have Application Dial Rules set up to handle converting numbers to what I need by stripping, adding 9s, adding 1s, etc. It all works great when I'm using Jabber as a soft phone.
My problem is that almost nobody in the company has a PC camera/mic/speakers. So all of the Jabber clients will be in phone control mode. Because the call originates from the phone and not from an application, the Application Dial Rules get bypassed. I understand why this is happening but I'm hoping there is a way around it. Is there some setting that tells CUCM to notice that there was a CTI call to the phone from an application requesting that it make the call or something like that where CUCM realizes that the request "initially" came from a Jabber client?
OR is there some way for me to put in route patterns similar to the App Dial Rules but specify that those patterns are only available when the number is sent enblock so they don't mess with regular dialing?

Why dont you apply called party transformation rules and modify the called number as per your need.

Jabber for Windows cannot control 8841 desk phone

Hello Team,
We have a problem with desktop phone control in case of 8841 phone.
When the user try to switch to the 8841 phone in Jabber then we got the following error message in the log:
2014-11-07 09:39:53,855 ERROR [0x00000298] [ice\TelephonyAdapterPhoneDevice.cpp(178)] [TelephonyAdapter] [TelephonyAdapter::selectDeviceImpl] - switchMode to device [SEP84802D7698D6] failed with error [eDeviceRegCouldNotOpenDevice]
We get the red X on the phone icon, and the desktop phone control is not working.
If the same user try to control 7940 phone, then it's working fine.
The environment: UCM 9.1.2.12901-3, CUPS 9.1.1.51900-5, Jabber for Windows 10-5.2
Edited:
Same issue with UCM 10.5.1, CUPS 10.5.1, and Jabber for Windows 10.5.2.
Regards,
Zsolt

Hi Zolt,
The RT phones need below end user permissions also in order to control deakphones:
Standard CTI Allow Control of Phones supporting Connected Xfer and conf
Standard CTI Allow Control of Phones supporting Rollover Mode
If they are not added, please add these permission.
Regards

Jabber for Windows 9.2 Deskphone Control

Hi,
I have a deployment with:
CUCM 9.1(1a) (9.1.1.20000-5)
IM and Presence 9.1(1a) 9.1.1.20000-5
Jabber for Windows 9.2.3(4417)
I have got most features working but Deskphone Control is not working. I can see the devices associated with my user from within Jabber when I select "Use my phone for calls" but cannot control them.
The connection status page shows the correct IP address for the CTI server.
I have spent hours reading through various documents and forums which seem to contain contradictory advice.
To clarify theserver versions that I have deployed support the new UC Services which are referenced from a Service Profile which is assigned to the user.
I am not making any progress resolving this issue. Does anyone have any advice on how to move forward with this?
Thanks
James

Hi Daniel,
we have a Problem with AD-User and DeskPhone ...
The "Active Local User" can control a DeskPhone
The "Active LDAP Synchronized User" can't control a DeskPhone from same PC, but he can controll a Softphone.
Cisco UCM - 9.1.2.10000-28 with LDAP Sync/Auth via 3269 (success)
Cisco UCMIMP - 9.1.1.31900-1
Cisco Jabber - 9.6.0 Build 17088
564 INFO [0x0000226c] [src\common\thread\WorkerThread.cpp(94)] [csf.ecc] [run] - Started thread: CtiConnection
564 DEBUG [0x0000226c] [utilities\socket\TcpSocketHelper.cpp(82)] [csf.ecc] [connect] - About to connect to 172.20.1.11
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(957)] [csf.ecc] [SendRequest] - CDPProvider::SendRequest, msg.sequenceNumber=1, pObject=0477A214, pdunames[msg.msgID]=PROVIDER_OPEN_REQUEST
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(967)] [csf.ecc] [SendRequest] - SendRequest setting msg.sequenceNumber to , msg.sequenceNumber=2
564 DEBUG [0x0000226c] [oneprovider\QBE\ProtocolElement.cpp(330)] [csf.ecc] [encode] - Message::encode: , msg.protoVersion=0x000e0000, msg.msgID=3, sizeof(Header)=32, fixedSize=108, varSize=90
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(973)] [csf.ecc] [SendRequest] - SendRequest Succeed., pdunames[msg.msgID]=PROVIDER_OPEN_REQUEST, msg.sequenceNumber=2
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(986)] [csf.ecc] [SendEvent] - CDPProvider::SendEvent, pObject=0477A210, nType=1001
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(919)] [csf.ecc] [OnEvent] - CDPProvider::OnEvent, pObject=0477A210, nType=1001, pvThis=0477A210
564 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(317)] [csf.ecc] [ecc::DeskPhoneConnectionContext::OnProviderEventUpdated] - OnProviderEventUpdated(1001), state=STATE_INITIAL_LOGIN, loginstate=LOGINSTATE_OPENING
564 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1148)] [csf.ecc] [DispatchTheMessage] - CDPProvider::DispatchTheMessage, nPduNum=4, pduName=PROVIDER_OPEN_RESPONSE
564 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1232)] [csf.ecc] [DispatchTheMessage] - Received , pdunames[nPduNum]=PROVIDER_OPEN_RESPONSE, seqNum=2
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(267)] [csf.ecc] [HandleMessage] - CDPProvider::HandleMessage, nPduNum=4
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(407)] [csf.ecc] [HandleResponse_ProviderOpen] - CDPProvider::HandleResponse_ProviderOpen
564 DEBUG [0x0000226c] [oneprovider\QBE\ProtocolElement.cpp(360)] [csf.ecc] [decode] - Message::decode: , totalSize=107, type=0, magic=4294958557, msg.protoVersion=0x000e0000, pduNum=4, hdrSize=32, fixedSize=52, varSize=31
564 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(415)] [csf.ecc] [HandleResponse_ProviderOpen] - CUCM protocol version: , resp.getProtoVersion()=0x000e0000
564 WARN [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1026)] [csf.ecc] [ResetHeartbeatTimer] - m_heartbeatIntervalS not set, timeout not set.
845 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1148)] [csf.ecc] [DispatchTheMessage] - CDPProvider::DispatchTheMessage, nPduNum=126, pduName=PROVIDER_OPEN_COMPLETED_EVENT
845 DEBUG [0x0000226c] [c\deskphoneprovider\DPProvider.cpp(1290)] [csf.ecc] [DispatchTheMessage] - PDUTYPE_ProviderEvent or PDUTYPE_Heartbeat, nPduNum=126, pdunames[nPduNum]=PROVIDER_OPEN_COMPLETED_EVENT
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(267)] [csf.ecc] [HandleMessage] - CDPProvider::HandleMessage, nPduNum=126
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(488)] [csf.ecc] [HandleEvent_ProviderOpenCompleted] - CDPProvider::HandleEvent_ProviderOpenCompleted
845 DEBUG [0x0000226c] [oneprovider\QBE\ProtocolElement.cpp(360)] [csf.ecc] [decode] - Message::decode: , totalSize=161, type=0, magic=4294958557, msg.protoVersion=0x000e0000, pduNum=126, hdrSize=32, fixedSize=72, varSize=65
845 WARN [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(502)] [csf.ecc] [HandleEvent_ProviderOpenCompleted] - ProviderOpen failed: reason: 0x8ccc0060, Directory login failed - authentication failed.
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(986)] [csf.ecc] [SendEvent] - CDPProvider::SendEvent, pObject=0477A210, nType=1008
845 DEBUG [0x0000226c] [rc\deskphoneprovider\DPProvider.cpp(919)] [csf.ecc] [OnEvent] - CDPProvider::OnEvent, pObject=0477A210, nType=1008, pvThis=0477A210
845 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(317)] [csf.ecc] [ecc::DeskPhoneConnectionContext::OnProviderEventUpdated] - OnProviderEventUpdated(1008), state=STATE_INITIAL_LOGIN, loginstate=LOGINSTATE_LOGGING_IN
845 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(891)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::DPLogoutWorkItem] - create DPLogoutWorkItem
845 DEBUG [0x0000226c] [pper\DeskPhoneConnectionContext.cpp(892)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::DPLogoutWorkItem] - Setting _loginState = LOGINSTATE_DISCONNECTING
845 DEBUG [0x0000226c] [c\deskphonewrapper\CC_DPService.cpp(926)] [csf.ecc] [ecc::CC_DPService::raiseLoginFailure] - raiseLoginFailure(5)
845 DEBUG [0x000013a0] [pper\DeskPhoneConnectionContext.cpp(898)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::run] - DPLogoutWorkItem::run()
845 INFO [0x0000226c] [\deskphonewrapper\CC_DPService.cpp(1078)] [csf.ecc] [ecc::CC_DPService::notifyConnectionStatusObservers] - dispatching ConnectionStatus Change eIdle
845 DEBUG [0x00002788] [c\deskphonewrapper\CC_DPService.cpp(298)] [csf.ecc] [ecc::CC_DPService::start] - Finished waiting for deskphone to go in to service...
845 INFO [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(218)] [csf.ecc] [Close] - CDPProvider::Close
845 INFO [0x0000226c] [control\CallControlManagerImpl.cpp(3092)] [csf.ecc.evt] [ecc::CallControlManagerImpl::notifyConnectionStatusChange] - CONNECTION_STATUS_CHANGE: eIdle
845 ERROR [0x00002788] [control\CallControlManagerImpl.cpp(1989)] [csf.ecc] [ecc::CallControlManagerImpl::doConnect] - doConnect() returnCode : AuthentincationFailure
845 DEBUG [0x000017a0] [s\telephonyservice\ECCObservers.cpp(153)] [csf-unified.telephony.ECCObserverLogger] [ECCObservers::onConnectionStatusChange] - onConnectionStatusChange(status = eIdle).
845 DEBUG [0x0000226c] [\deskphonewrapper\CC_DPService.cpp(1014)] [csf.ecc] [ecc::CC_DPService::raiseProviderStateChange] - Got cxn change, disconnecting deskphone video Idle
845 DEBUG [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(957)] [csf.ecc] [SendRequest] - CDPProvider::SendRequest, msg.sequenceNumber=2, pObject=0477A214, pdunames[msg.msgID]=PROVIDER_CLOSE_REQUEST
845 ERROR [0x00002788] [control\CallControlManagerImpl.cpp(2025)] [csf.ecc] [ecc::CallControlManagerImpl::doConnect] - doConnect() returnCode : eDeviceRegAuthenticationFailure
845 DEBUG [0x000017a0] [elephonyservice\BackgroundWorker.cpp(35)] [csf-unified.telephony.BackgroundWorkerLogger] [BackgroundWorker::doTask] - Adding new task to BackgroundWorker. Task name is: TelephonyAdapter::onConnectionStatusChange
845 INFO [0x0000226c] [rc\deskphonevideo\DeskPhoneVideo.cpp(76)] [csf.ecc] [ecc::DeskPhoneVideo::disconnect] - disconnecting
845 DEBUG [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(967)] [csf.ecc] [SendRequest] - SendRequest setting msg.sequenceNumber to , msg.sequenceNumber=3
845 INFO [0x00002788] [control\CallControlManagerImpl.cpp(2411)] [csf.ecc] [ecc::CallControlManagerImpl::doDisconnect] - --->
845 DEBUG [0x000017a0] [common\processing\TaskDispatcher.cpp(29)] [TaskDispatcher] [Processing::TaskDispatcher::enqueue] - Enqueue TelephonyAdapter::onConnectionStatusChange - Queue Size: 9
845 DEBUG [0x0000226c] [c\deskphonevideo\DeskPhoneVideo.cpp(315)] [csf.ecc] [ecc::DeskPhoneVideo::stopCdp] - Stopping CDP
845 DEBUG [0x000013a0] [oneprovider\QBE\ProtocolElement.cpp(330)] [csf.ecc] [encode] - Message::encode: , msg.protoVersion=0x000e0000, msg.msgID=9, sizeof(Header)=32, fixedSize=4, varSize=0
845 INFO [0x00002788] [pper\DeskPhoneConnectionContext.cpp(267)] [csf.ecc] [ecc::DeskPhoneConnectionContext::stop] - DeskPhoneConnectionContext::stop
845 DEBUG [0x000013a0] [rc\deskphoneprovider\DPProvider.cpp(973)] [csf.ecc] [SendRequest] - SendRequest Succeed., pdunames[msg.msgID]=PROVIDER_CLOSE_REQUEST, msg.sequenceNumber=3
845 DEBUG [0x0000226c] [c\deskphonevideo\DeskPhoneVideo.cpp(318)] [csf.ecc] [ecc::DeskPhoneVideo::stopCdp] - CDP stopped
845 INFO [0x000017a0] [src\AccessoriesManager.cpp(234)] [csf.accessory.event] [accessory::AccessoriesManager::onConnectionStatusChange] - Received onConnectionStatusChange - eIdle
845 DEBUG [0x00002788] [pper\DeskPhoneConnectionContext.cpp(891)] [csf.ecc] [ecc::DeskPhoneConnectionContext::DPLogoutWorkItem::DPLogoutWorkItem] - create DPLogoutWorkItem
845 INFO [0x000013a0] [\deskphoneprovider\CtiConnection.cpp(49)] [csf.ecc] [stop] - CtiConnection::stop
Thanks,
Guennadi

Jabber for Windows 9.2 deskphone control issue

Hi experts,
I'm having a problem with the newly installed Jabber for Windows 9.2.0. When I click on the bottom right "control phone" and select my Cisco 7941 it fails. I tried restarting the Cisco CTIManager service with no luck.
Deployment:
IM&Presence: cloud (Webex service)
CUCM version: 8.6(2a)
LDAP integration: full (with authentication)
Deskphone control was working prior the upgrade of Jabber for Windows. Everything else remained the same version.
Using Jabber softphone as a client still works fine.
CUCM ENd User is correctly configured.
Wireshark trace of my Jabber for Windows 9.2 client communicating with CUCM when attempting to control my deskphone shows the following:
Username: filippo.zangheri
Password: checked three times (it is correct because Jabber softphone works fine).
Any hint?
Thanks.
Filippo

Davide,
I know i am kind of late to the party on this one but i have fixed my issue and wanted to give you the information to see if this will work for you. If this is even still an issue?
I too had the same issue and just like you i confirmed everything was correct however I discovered something when I was looking into my End User profile on the CUCM. I had originally swapped my 7971 phone with a new 8945 phone and I had both phones associated with my line for a while before I removed the old 7971.
My End User profile still had both phones associated with my number even though the 7971 phone had been removed from my line. This was not allowing the CTI to connect to my 8945 phone or allow my jabber client to "Control Phone" properly because it couldn't figure out which phone to control. I went into the CUCM and physically deleted the 7971 phone from the system which released the associated phone in my End User profile. Once I did that, I "Control Phone" in my Jabber client and voila it worked like a charm!
To make sure I didn't have any Jabber client issues after doing this i signed out of my Jabber client and deleted the local system profile for the Jabber client and then signed back into Jabber and let it recreate the profile. Once that was done i have not had any issues with my Jabber client controlling my phone and all functions work perfectly.
Hope this helps...

Jabber For Windows deskphone control

All,
This is my last stop before getting with TAC and I just wanted to see if anyone has had and resolved this issue:
Jabber for Windows (all versions up to 9.1) Desk phone control most times takes several attempts to become active and working. If the client is shut down, the client defaults to Computer for calls and it takes several more attempts to get desk phone working again (half the time I get a red X over device option icon.
Anyone else experienced this or have a suggestion?
CUCM8.5
Presence 8.6
Gareth

Richard,
I managed to get everything working again (hopefully!).
I removed all devices from my prefile and re added them, as well as restarting the presence service and CTI service in CUCM. Seems to have done the trick for now.
Gareth

Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

Jabber for Window, phone mode, how to disable "use my computer for calls"

We have a Citrix environment and only want to control the Cisco deskphone with Jabber for Windows in the phone mode.
We use CUCM 8.6.2 and I have installed Jabber for Windows 9.7.0 and all works fine, I can control my deskphone, make and receive calls, phonebook and Outlook integration works fine.
Is it possible to disable "use my computer for calls" as we do not want users to make calls via Citrix, but only use the deskphone for this.
Thanks, Perry

Hi Matthias,
Soft-phone mode cannot be disabled. Supported Features on Virtual Environment are the following.
Supported Features
    Instant messaging and presence with other Cisco Jabber clients
    Desk phone control
    Voicemail
    Presence integration with Microsoft Outlook 2007, 2010 and 2013
We have an existing defect which is in Terminated state because feature is not supported hence cannot be fixed.
CSCub40605 - J4W - Ability to disable softphone mode in Citrix environment.
HTH,
Please rate if you find this post helpful.
Regards,
Mohammed Noor

Jabber for Windows openLDAP and Deskphone Control

Hello all
I have a new install of 9.1 CUCM, with CUCM IM and Presence. I'm trying to get Jabber 4 windows functioning with an openLDAP directory, and also get Deskphone control working. I suspect i missed something with the configuration as this 9.1 interface is a little different than i'm used to.
First of all, does the concept of a Jabber-Config.xml still apply to a 9.1 install or does the "Service Profile Configuration" in the CUCM interface write the Jabber-config.xml file for you? If my customer uses openLDAP for their LDAP how should I configure the "Service Profile" or do I still use a jabber-config.xml file?
I have successfully tied openLDAP into CUCM with Authetication and brought the users into CUCM. I tested Authentication by logging into the End user page for both CUCM and the CUP server so I know authenticaiton is working. I can login to Jabber but when i click on Help "connection Status" it shows me only connected to "PRESENCE" and "OUTLOOK ADDRESS BOOK" my "Directory", and DESKPHONE" will not connect.
Can I actually get a copy of "my jabber-config.xml" file from the CUCM server to see what it looks like?
Thanks all

Ok I have half of the problem resolved. I got Deskphone controll working with CTI.
Still working on the LDAP issue with openLDAP
My config file looks like so
<?xml version="1.0" encoding="utf-8"?>
   EDI
   1
   ldap.acme.ca
   389
   backup.acme.ca
   389
   0
   uid=voipldap,ou=Users,dc=acme,dc=ca
   password
   givenname
   (&(objectClass=inetOrgPerson)
   telephonenumber
   uid
   ou=users,dc=acme,dc=ca
I got this from page 117 of this guide
http://www.cisco.com/en/US/docs/voice_ip_comm/jabber/Windows/9_1/JABW_BK_CA48EE46_00_cisco-jabber-for-windows-administration.pdf
The error I'm getting "invalid credential" but i know they are good because i'm using the same account and path for the CUCM LDAP sync.
Any help would be appreciated.

Jabber for Windows LDAP Profiles

I have been unable to find a lot of information on LDAP profiles, but I came across a blog that said that LDAP profiles are only used for Android, iphone and ipad. It stated that the only way to control the search base on Jabber for Windows is by using the jabber-config.xml file. So far this appears to be true based on my limited testing.
I have been able to integrate with OpenLDAP using the jabber-config.xml file to set the server and search base. The only problem i can see with this particular design is I would have to give all users the same LDAP profile and search settings. In our environment this will not satisify our requirements.
Does anyone know of a way where i can integrate with OpenLDAP, use the Jabber for windows client and control the LDAP search setttings on a per user basis?
Thanks

Yes but you won't like it.
Group Configuration File NamesYou specify the name of the group configuration files in the Cisco Support Field on the CSF device configuration in Cisco Unified Communications Manager.If you remove the name of the group configuration file in the CSF device configuration on Cisco Unified Communications Manager, Cisco Jabber for Windows detects the change, prompts the users to sign out, and loads the global configuration file. You can remove the name of the group configuration file in the CSF device configuration by deleting the entire configurationFile=group_configuration_file_name.xml string or by deleting the group configuration filename from the string.If users have desk phone devices only, use the following command line argument to specify unique names configuration files for different groups: TFTP_FILE_NAMESee the Install Cisco Jabber for Windows chapter for more information about the command line arguments.
Please remember to rate helpful responses and identify helpful or correct answers.

Jabber for Windows 9.2.4 - Spinner freezes on "forward calls to"

On Jabber for Windows 9.2.4 when we activate "Forward calls to" - the forward is set on controlled phone, however the spinner freezes (see image) and won't clear until a different phone is selected for control. Setting "forward calls to" "none" does not clear the spinner.

Hi Mark,
this is known issue: 'CSCui37305 - After forwarded call, "Setting call forwarding..." does not disappear' and it is already resolved in 9.2.6.
Regards,
Nebojsa

Cisco Jabber for Windows Client SDK

Is there an SDK for Cisco Jabber for Windows client? I could only find the Web SDK. Are there no other SDKs that would let me control features of the Jabber Windows Client?

And in order to avoid TAPI limitation, they say they have started using Jabber which controls all phone functionalities through an Application User connected to the Call Manager.
Assuming they are referring to the normal Jabber for Windows/Mac/iOS/Android applications then this is wrong. Jabber - the client, not the IM&P servers which are part of the CUCM cluster (if you're familiar with Lync consider CUCM+IM&P servers a Front End Pool) - do not use an Application User at all. When a user starts Jabber, assuming SAML SSO is off, they supply an email address. This is used to find the servers via DNS SRV records, or the Mobile and Remote Access Expressway (roughly analogous to a Lync Edge pool) to tunnel through the firewall. After the email address they are prompted for their End User username and password. This is then used to access several APIs on the server, namely the User Data Service to discover what the user has. This would include what the user has configured/available to them. After this is done the Jabber client does one of three things with respect to phone functionality:
If the user has no phone devices provisioned for them - physical or software - it becomes an IM&P client only.
If the user has a software phone phone provisioned, it registers as that using SIP. In this way Jabber is the actual phone. This is called a CSF device for Jabber Windows/OS X.
If the user has a desk phone assigned to their End User account AND administrative policy is to default to desk phone control, it registers to CTI Manager on the CUCM server to control the user's physical phone.
A user can toggle between option two and three, if appropriately provisioned, but cannot have both simultaneously. In other words, Jabber is either controlling a physical phone over CTI or is a phone itself using SIP. The difference is where the audio/video media is sent from/to.
All of this happens using that human's End User credentials.
Now, if you wanted to have a server control the user's phone - either a physical one or Jabber - you would use the TSP as an interface to CTI Manager on the CUCM server and receive real-time events (e.g. the user went off-hook, the phone is ringing with this caller ID, etc.) and issue commands to that phone (e.g. make a call to X). This is done using an Application User account because the server would need to do this for multiple users simultaneously. If you also use the Super Provider concept, the CUCM administrator doesn't have to take the extra step of associating every phone to your Application User manually. Instead, you can simply issue CTI subscriptions to see any/all device activity you want.
This is all assuming you wanted to do the integration server-side to avoid having to update the Cisco TSP application on every user PC (which also limits your WPF application to machines capable of running the TSP) every time the CUCM administrator patches the servers. If you don't care about that, then you can do this all client-side on the user's PC, and have them supply their End User credentials.
Of course, you could also reconsider the Jabber SDK and just embed the make/receive call functionality directly into your application instead.

Jabber for Windows- VM issue

I had configured Jabber for windows in windows 7, the problem is after logging into jabber client iam not able to get the "phone accounts" under options.
Iam able to call , and recieve calls but no voice mail. In the Jabber cleint diagnostic it shows username and password is wrong for voice mail.
If i have 'phone acounts' option in jabber client i could set username and password for voice mail. Iam able to telnet the unity server.
Any clue?
We have IM&Presence 9.0, CUCM 9.0
Jabber - 9.2
Tnx
Bobby

HI,
As Aron states - you can configure your client to use same login and password ID as other UC services. This will then mask the fields you see in your jabber client. This is great when you don't want your users to have to populate the fields. The less they have to do the better.
Check your Unity Connection system - is it AXL ot AD or neither ?
If you can, your better to use only one username / password across your UC environment. For now just check your setting for the VM service is not set .

Jabber for Windows Voicemail Playback Issue

Hi,
I have Jabber for Windows installed and voicemail is working ok but when I playback a voicemail from the Jabber client the MWI light does not go out on the phone. If you do the opposite ie listen to a new voicemail through the phone the new message indicator goes out on jabber.
Also if you listen to the voicemail through Jabber client the voicemail plays through the PC speakers. Is there anyway in getting Jabber to direct the call to the phone so the user can pick the handset to listen like you can when listening to voicemail through the Unity Connection Web Inbox.
Thanks for you time
Regards
Neil

Hi Neil,
Playing the voicemails in Jabber should turn off the MWI light. You need to open a TAC case and sent on a problem report to debug this further.
For the second question, the only way I think you can do this is by setting Jabber to deskphone mode and then using the "Call Voicemail" button.
- Colin

Cisco Jabber for Windows Voicemail issue

At this I'm in processing of implementation Cisco Jabber UC solution for big Company.
I use CUCM 9.1.2, Cisco IM and Presence 9.1.2, CUC 9.1.2, Cisco Jabber for Windows 9.6.1.
I have issue in Cisco Jabber with VoiceMail Integration - when I leave voice message for any user,
than this message is arrived only him Cisco IP Phone, but not in him Cisco Jabber.
From Cisco Jabber Connectivity status in help menu I see that VoiceMail service is successfully connected
and I see VoiceMail button in Cisco Jabber.
How can I resolve this issue?

Have you configured the UC Service profile on CUCM with both Voicemail server and mailbox servers?

Jabber for Windows 9.0.1 phone control of Cius?

Similar Messages

Maybe you are looking for