K8N NEO FSR - wont detect HDs on first powerup (daily)

I'm having this strange problem ever since i installed this Motherboard.
First time I boot up(daily basis), it does not detect the hard drives.. any of them...
I get to the point where it notices my memory timings and says "Detecting hard drives.." (or something like that) and it just hangs there. I hit ctrl-alt-delete (also if i power it off then back on it works too) and when it comes back its fine.
Anyone had this before? Could be there's a quick fix but before I start to pick the system apart I wanted to check here first.
thanks

OK here are some specs:
AMD64 3200+ (Newcastle) - no OC
Generic 3200 DDR ram
MSI K8N NEO FSR (latest bios)
BFG 6800 OC (modded)
primary controller (ata) has: Maxtor 6Y060P0 & WDC WD800JB-00DUA3
secondary controller only has DVD-RW drive.
Sata controller has ST3120026AS
Same setup as in previous motherboard.
I guess i'll just need to check the cabling is secure once again, to be sure.
it seems this is not a common issue so most likely i can find something wrong other than with the mobo.
thanks

Similar Messages

Ms-7030 msi k8n neo fsr wont start

i made my system a follows.
amd 2800+ 64
msi k8n neo fsr
kingston 400mhz ddr value ram
6600gt inno3d agp
wd800 80gb hardrive
300 watts psu
brought the system home everything was working fine except for continous stuttering on hl2. also wid it came a smart cobra lite 56k modem from zoltrix, which was installed while makign the system, the modem had been deteced but when i tried to connect to the net, the status of the modem was found to be not connected, i removed the modem, restarted by switching the pci slots and everything but to no avail, put in an older zoltrix modem from my old pc, to no avail the modem just wudnt get recognized. the same modem though worked in my older p3 system. i took the systm to the place where they assembled it.as the system booted the modem got deteced, got winxpsp2 installed wid a fresh install. everything worked fine for a day untilt eh modem once again went back into death mode.took it back to the hardware shop i remember they were using an older keyboard on it too, well as they pressd the power button, the cpu fan and the gfx card fan moved a second and then stopped no booting
they replaced mobo then and there. even the same problem occured wid the new mobo, i left the system there to be tested but the thing i dont understand is they had assembled an tested the system by using the old keyboard and even then there was no problem. this time the system was working but as it reached the assemblers the cpu and gfxs card fan moved a sec as if power was fed for a second and dided changed psu's on one try on dry boot that is widout hd connected. the fans continously worked we removed power put into chasis and tried again to start but to no avail.
cud it really be the keyboard problem if that is solved then the problem left to deal wid is the modem wud the pci slots act the same way even on the newer board or chaning modems wud do any good, changed rams also that wudnt help booting either.
in both of the new mobos i didnt get the msi sticker that adds to my frustration.
posted this on another forum too, tha guy was havng problem using an older keyboard.

its really nice of u guys to reply so quickly its really appreciated. the thing is if the psu wasnt upto the job it wud have given away 3 days ago. but it didnt other psu tried also same problem. after a couple of hours ill be off to the hardware shop to see wat came out. the ram was reseated properly on all 3 slots.
plus the 300watts psu may not even be 300 cuz its locally made and stupid quality maybe lower to around 250, but the system worked fine all along, checked rail supplies on the mobo mopnitor and they seemed fine.will keep u guys updated.

K8N Neo FSR Bios overclocking functions help needed

Hi all, I am a small pc builder for the family and i have found some problems with the bios of my uncles K8N neo FSR which I recommended for him. Basically it wouldn't seem to overclock with the 'Dynamic Overclocking' function on bios v1.7 but did manually by adjusting FSB incrementally (ie from 200 to 205 Mhz). When I questioned this before someone had mentioned that it could be ok to run like this. However I have since updated the bios to v1.9 and even v2.1 as they became available but now neither seem to overclock manually nor using 'Dynamic overclocking'
Firstly though, can someone clear up my first conception; To test if the Dynamic Overclocking function is working can I set it to a higher setting (ie.'Commander'), save and exit bios (restarting) ---> go straight back into bios ----> go straight back into Cell Menu and check 'Current frequency of cpu' has changed?
I only ask this as if this is the case then my Dynamic Overclocking function hasn't worked with three bios' and I wont bother with anything until I RMA the board lol, as I have never been able to change the frequency of my cpu at boot/bios stage with the dynamic overclocking function.
Can anyone help me?

Hi Stu, yesterday I think i found out what u mean lol. I studied a 'Sticky' ? about overclocking A64s and found some interesting stuff. Apparently overclocking the HTT is dangerous, and A64s are always at least half locked. Now with this in mind Ive been wondering if there are interlocks built into my mainboard stopping me from using the 'CPU Overclock' function to overclock my pc manually from the set 200Mhz while my HTT is still set at 4x. -I say this as the HTT on my system is 800Mhz for a socket754 Sempron 3000Bx, thus overclocking this would increase my HTT above the 800Mhz threashold (I think) lol. All sounds complex but I think Ive figured it out as Im following instructions from the sticky to lower my HTT multiplier before increasing my cpu overclock. Its hard as my mainboard has Nforce3 chipset which has different ways of overclocking to every other board lol. So far I have managed to increase the overclock, but only when the HTT multiplier is lowered to 3x. I have also lowered my cpu multiplier though, and thus am trying to figure out where my 1810Mhz clock speed has changed to 1630 lol. Will try again now. I want to raise the clock speed above 1810, keeping the HTT lower than 800 and leaving the memory alone at 400DDR lol. Im hoping the memory is seperate as it seems to be on this chipset.

Weird problem with k8n neo fsr

hello!
i have weird problem with my K8N Neo-fsr and Athlon 64 2800+ socket 754, when i try to overclock i change in bios HT from 4 to 3 (for better stability), after restart nothing happen, my pc wont boot, also nothing on screen, so i must clear cmos for solve my problem and set to 4 i try several bioses from official to moded also pinochio`s and syar`s moded and allways the same issue is it problem with processor? or motherboard?
thanx for your help and sorry for my english

You should first get down cpu ratio, then get up cpu fsb and as you wanted set ht frequency from 4 to 3 and "save changes and exit" if it doesn't boot change you psu (at least antec 380 or tagan) or go fast to send back your mobo to reseller!!

K8N Neo-FSR doesn't boot

Hello everyone
I got my mobo (K8N Neo-FSR) more than 6 months ago, and worked without any problems until today.
First of all, I made a BIOS update from 1.7 to 1.9 using MSI Live Update. No problems to report, the computer worked after that for several hours. Then I turned off the PC. And the next time I wanted to turn it on, it didn't boot.
Here's my D-Bracket message :
This corresponds to "Initializing keyboard controller"
The problem is that apparently it has absolutely nothing to do with my keyboard, as I tired changing it.
Clearing CMOS didn't help.
Any ideas how I can fix this? Or should I contact the support?

Before you answered, I tried to check the RAM. As a matter of fact by removing one of 3 memory sticks the computer worked. Later I figured out that if I lower the RAM frequency from 200 MHz to 166, all 3 sticks work perfectly well.
Now the question is : WHY THE HELL DID THIS BIOS UPDATE MESS UP MY RAM??? Weird.

MSI K8N NEO-FSR BIOS Flash Corrupt

So there was an updated BIOS for my motherboard version 1.8 while I had 1.7. I went ahead and updated and it went fine. But then I noticed that my CPU speed was dramatically reduced and the multiplier was set to 5.0 giving me a 1ghz CPU. While I thought maybe the CMOS needed to be cleared I went ahead and did that but to no avail I wasnt able to fix that problem. I went over to the MSI Live Update to check for a new BIOS update and it had said that I had 1.8 version while the current version is 1.7. Just a few days before it said 1.8 was the latest. Hmmm. So I went off to the MSI website to find version 1.7 and downloaded it. To my surprise version 1.8 was available on the MSI website. I used the WinFlash program to flash my BIOS. Before doing so I closed all open applications including anti-virus, browsers, chatting programs, and so forth. But the flash was going VERY slow and it stopped with unable to verify bios. This made me scared pooless. After I restarted to no surprise my computer started up with BIOS Checksum error and asked for a floppy. I didn't have a floppy drive connected at the time but the computer shut itself off automatically. So I went and connected and floppy and looked up online at the MSI website about how to recover the BIOS. I found it and for my AWARD bios i followed the procedure. But each time it detects the floppy drive and then the computer shuts itself off. Even if i have no disc inside the floppy drive it'll shut off. Is it supposed to do this? I am unable to reflash my BIOS because of this behavior. I don't know what the cause of this problem is now. Did maybe the recovery portion of the BIOS get corrupted too? Please help. Let me know if you need any more information. Thanks in advanced. My specs are below btw:
MSI K8N NEO FSR
AWARD REV. 1.8
AMD ATHLON 3200+ 754
PDP 2x512MB RAM
NVIDIA GeForce 6800 Ultra
Ultra-X 500watt
WD 160GB IDE, Seagate 200GB IDE
Pioneer D-A07
Windows XP SP2, Gentoo Linux, Ubuntu Linux

Okay I tried taking unnecessary stuff out but it didn't help. I'm actually having the same problem this guy is having : https://forum-en.msi.com/index.php?topic=86508.0
Hmm looks like i might be in for a new motherboard or i can try the RMA process but I dont know how long that will take. Other than that...I dont know what to do. I could buy myself a new bios flash chip but they're damn expensive and I'd rather just buy a new motherboard. On another note I noticed that when I boot up the pc and i see that it detects the floppy I immediately pressed the reset button but it'll still shut down. So it's as if there is a timer somewhere. What the hell is up with this? It also seems MSI didn't release bad BIOS releases for my board only. Seems like people with other boards are having tons of problems with the latest BIOS releases.

K8N Neo FSR won't boot.

I've flashed mainboard BIOS using LiveUpdate from v1.6 to latest v1.9 for some reason (CPUID for Sempron 64bit, low DDR speed). Everything ok . Then XP became unstable (blue screens) and finally PC wont boot (one LED is green, nothing appears on the monitor) . Any idea, except to put it back to the reseller, what I probably have to?
Does anyone have the dg. LED description for this board (there's neither anything in my printed manual nor I've found this in the web)? The description was there for older mainboards, why is this not there now???

you did the big mistake if you used live update!!!
Bios flashing and live update:
look at this: https://forum-en.msi.com/index.php?topic=84865.msg606175#msg606175
and this: https://forum-en.msi.com/index.php?topic=14909.0
and this https://forum-en.msi.com/index.php?topic=69.0
something abou Bios recovery:
https://forum-en.msi.com/index.php?topic=71165.0
https://forum-en.msi.com/index.php?topic=65951.0
btw look at this, it`s about bios version 1.9 for MS-7030, this bios has lots of bugs at K8N Neo-FSR:
look at this: https://forum-en.msi.com/index.php?topic=87562.0
and this: https://forum-en.msi.com/index.php?topic=86772.0
I suggest you to revert back to official version 1.7 (which is stable) or modded version 1.56 by pinochio...look at this: https://forum-en.msi.com/index.php?topic=59711.0 and also look at syar`s collection: http://homepages.nildram.co.uk/~chsmith/Syars_Bios_Collection/
go to NEO1 and download 7030MOD.156

[ram]Kingston + MSI K8N Neo-FSR?

my system:
AMD Athlon 64 3000+, 2.0ghz
MSI K8N Neo-FSR(bios 1.40)
Asus V9999 GeForce 6800 256MB Gamer Ed. AGP
Audigy 2 zs
Win xp pro sp1
Hiper power 420W
I just bought the Kingston ValueR. PC3200 DDR-DIMM 1024MB Kit w/two matched ValueRAM 512MB.
When I boot up the pc just makes a sound piip piip piiip continuing....
I can't do anything since it wont boot up & i tried diffrent dimm slots but it didn't work :(
Earlier i've set the settings to t1 & the volt to 2.56 from before. Does this has something to do with it ? How can I reset the bios if I can't even get in dos :s
What should I do ?

Reset the cmos using the Jumper, is you have a manual it will show you where this is located. It will set the Bios back to Default,then you have to set it up the way you want it again. To get the RAM working set it to DDR333=166, that should sort out the No Post.
Your going to be out of luck here as the 'support' is basicaly non-existent, or just replies from people trying to get their post count up higher, I'm afraid to say.
Good luck.

K8N Neo-FSR compatibility?

hello!
I want to buy a new motherboard K8N Neo-FSR for my computer-CPU AMD 64 2800+ (1800MHz) ADA2800AEP4AP Clawhammer family: F, model: 4, Stepping: 8, Ext.Family: F, Ext.Model: 4, Revision: SH7-C0, 2xDDRAM Apacer 512MB UNB PC3200 CL2.5 P/N: 77.50739.15G, sound card Herculles Gamesurround Fortissimo 2, tv card ASUS TV/FM 7135, HDD SATA Seagate Barracuda 200GB model ST3200822AS, DVD RW Benq 822A and DVD ROM Benq 16/50, graphic card Sapphire Radeon 9800SE 128bit 128MB, keyboard Microsoft Multimedia Natural and Microsoft Intelimouse Explorer 2.0A wirelles USB. and i ask if will be this board compatible with all of these components, cpu, memory etc.
thanx for your answers and sorry for my english, i am from slovakia

V,
You have to research yourself each componets to figure our if it is suitable, especially your memory. Look for compatibility listings at various OEM web sites.
Your overall plan is OK but I question your selection of a first genertion AMD 2800 Clawhammer for your CPU. The Clawhammer is a 0,13 u core CPU with an older an less flexible memory controller. Scrape together a little more money and get yourself at least an AMD 3000/3200 + Venice or San Diego AMD CPU. You will be very glad you did later on.
Good luck,

MOVED: K8N NEO-FSR - Can't find network unit?

This topic has been moved to AMD64 nVidia Based board.
https://forum-en.msi.com/index.php?topic=118264.0

Quote from: Stu on 09-July-08, 03:00:42
Check that onboard LAN is Enabled in BIOS (under Integrated Peripherals)
Was "Auto"
Quote from: HenryW on 09-July-08, 04:58:56
Looks like they're here for K8N Neo-FSR.
http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=573
Will try this one, thanks! (Will post if it worked a bit later)
Umm, btw... Where should I extract the files?
Quote from: Fredrik Åsenius on 09-July-08, 05:07:48
Tjena Rikard! You have to describe your system in some detail.
Some famous culprits:
- Other PCI-cards.
- Poor or old Windows installation.
- Weak PSU.
- IRQ problem.
- A combination of all or any of above.
The network card is not a PCI-one, but integrated to the motherboard. Only card in the system is a PCI-E graphic.
Maybe poor or old windows, might try that...
Shouldn't be weak PSU, It's pretty good, I've been told.
IRQ?

S3 mode doesn't work fine on K8N Neo-fsr since overclocking, please help!

I have a K8N Neo-FSR (MS-7030) BIOS version 1.6 (I tried 1.4, 1.5), running AMD64 2800+ SK 754, 2x 256MB DDR400 Kingston valueram pluging in slot 1&2. It runs well except S3 mode .
Since I overclock HTT (everythings else have their own default values), S3 mode seems to work so crazy . After wake up from this usefull stop-grant standby mode, HTT is given back to its original speed, 200MHz, without notice (?!) .
You know that I don;t like this much, do you?
Who responsible for this function? Mainboard or CPU? If it's mainboard, which department will be sentenced, BIOS or chipsets/ICs?
Could anybody give me a solution to achive higher speed by overclocking without giving up using S3?
Thanks so much!

It's a bad new! I had bad feeling about DFI with the same problem, S3 mode resuming bring FSB back to df and even sometimes led the system to the ruin. But upgrading bios solved this issue. My old Abit did S3 mode fine. Now I have a new MSI and once again I must use teknophyle's way or slow hibernation instead.
On the same occasion, I wana ask about some shortcoming in 1.6 bios: power on by keyboard/mouse and power led options. I only found S3 wake up by keyboard/mouse but not keyboard/mouse power-on options! There is power led option in version 1.56 but it disapeared in 1.6. Now my mobo has no signal to differentiate between sleep and power-off. would you give back the useful power led option and add power on by combination keys in the near future bios version, syar? Look forward to hearing some good new from you :D.

Who have v1.56 bios for K8N Neo FSR,give me please.thx

who have v1.56 bios for K8N Neo FSR,give me please.thx

Bios Collection. *Updated * 7025 1.B beta4 follow Syar's MSI Nvidia64 Bios Collection link.

Cannot find the Power Led connector for JFP1 to connect on K8N Neo FSR

Hi,
I have just bought the MSI K8N Neo FSR (MS 7030) to build a new computer with (amongst others) an Athlon 64 3000 processor and an Enermax 3051 case.
I can't even get a start: if I click on "Power" I just get a red light under the Power button for 1 second and nothing start.
This may be related with the fact that I did not find a "Power LED" connector for JFP1 (I have connected all the others connectors, including the Power LED one for JFP2).
Thank you in advance for your help.
Precisions:
At the beginning, I had forgotten to connect the ATX 12V power connector on JPW1.
After having done that without getting an improvement, I did a Clear CMOS (after having unplug the power cable).
Now the CPU fan begins to turn just when I switch the power on from back of the case (and not from the power button) and stops turning after five seconds.
Sometimes, I get an orange light during 1/2 second on the D-bracket LEDs.

Quote from: Dr Stu on 20-November-05, 04:36:29
evidently if he fixed it, the solution was posted elsewhere
so what have you tried so far? has this system ever worked?
post your PSU specs. try powering up board outside the case in case there is a short somewhere
I have tried a different power unit, different JFP1 configerations, removing and replacing MB battery, changing the jumper settings on JBAT1 to clear CMOS.
Everything is just dead, no power anywhere. I get the fan light inside the Power unit to light up for 1 second when i connect the power cable and thats it. Its a 450 Watt power unit so it should be plenty. Maybe i will try removing the board and starting it that way.
This system has never worked, i just built it.

K8N Neo-FSR ~= K8N Neo Platinum

May have to replace my motherboard - a K8N Neo Platinum. Have seen the K8N Neo-FSR, from its spec I assume it is the same, apart from only 2 rather than 3 Ram slots?
Thanks
Derek

Hello !
You can see both specifications here:
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=572
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=571
Greetz

MOVED: K8N Neo Platnium not detecting PCI cards

This topic has been moved to Intel P4 & Celeron P4 based board.
K8N Neo Platnium not detecting PCI cards

I had a similar problem with a 945p neo platinum board. Anything I plug into any PCI slot didn't detect. I solved the problem by flashing to the latest BIOS for the board. Now everything seems to be working fine.
Maybe that might work for you?

K8N NEO FSR - wont detect HDs on first powerup (daily)

Similar Messages

Maybe you are looking for