K9N2 Diamond Win 7 sound problem

Hi, i have K9N2 Diamond + Creative X-Fi sound card, i have installed Win 7 32bit, and when i speeking at a skype, messenger, my frends dont hearing good, low sound.. I haved chenge my mic, driver,...same... at the xp was worked good. When i hearing music is working good...
Can somewon help me...??

Hi Tomween,
Based on the information posted, the Creative X-Fi Xtreme H/W Audio Card MSI Edition is an OEM product. These OEM sound cards are often customized for the motherboard manufacturer who ships or installs them, therefore the manufacturer in this case, MSI should be the primary contact for support and warranty issues.

Similar Messages

Wine : sound problem

i installed the game sof2 by wine.
the problem is that the sound in the game is bad
do u have solution?
thnak u

You can check winecfg -> Graphics to see if Direct3D Vertex Shader Support is set to hardware. If it isn't, switch it. Otherwise it's probably just a bug with emulating that game.
Here's the linux gamer's howto on the game; but it looks like they didn't have much trouble with it so it probably won't be much help.
Also if you don't mind, please don't post the same thread in multiple topics. Thanks.
Last edited by jb (2007-02-21 02:33:09)

K9N2 Diamond X-FI Problems

PC: Windows 7 32 bit, Phenom II x6 1090T, 4g corsair xms2, 9800gt, corsair psu tx650W
Can't change Mode, it stays always on Entertainment, can't change speaker configuration, it's on auto detect always. In XP everything worked fine. Recently tried with some realtek(!!!!) drivers, and can only switch between 5.1 and output for headphones. If I plug something to the extra jack (on the case, with the extra output cable from the x-fi card) my OS crashes for about 1 minute until it realizes what happens, then adds a extra 'headphone' button in my console cu launcher.
3D works on windows first run, but if i change it once (remove the tick) a restart is needed to work again.
I've seen other threads for those problems here and in creative labs forums and no one seems to care about those end-user problems.

Quote from: Mark on 01-June-11, 16:42:55
Have you tried the drivers from the MSI website? --> http://www.msi.com/product/mb/K9N2-Diamond.html#/?div=Driver&os=Win7%2032
Yes, I have, every possible version.

K9N2 Diamond, Hybrid SLi problem

I have built a new system and am wanting to try out the Hybrid SLi functionality, but everything that I can think of doing to get it to work fails.
Below is my setup
K9N2 Diamond Mobo
Ultra X3 1000W PSU
9800 GTX+ VPU
6 Gig DDR2 PC6400 RAM
2 500GB Seagate SATA drives
AMD X2 6000+ 3.1 Ghz Proc
Vista Ultimate 64bit
The following is what has been done:
1. Installed 1 drive, CPU, 1 stick of RAM, DVD/RW, and PCI sound card
2. Made adjustments to BIOS for initial install
3. Installed Vista
4. Installed drivers for onboard hardware and soundcard
5. Shut down
6. Installed Video card, 2nd hard drive and remaining RAM
7. Turned PC back on and went into BIOS and turned on Hybrid SLI with internal as primary adapter
8. Installed 9800 GTX+ drivers and software
9. Installed Hybrid Sli driver
10. Rebooted.
I still cannot get the Hybrid SLi program to start as it is not showing up in the system tray. I looked at the properties and see that it shows both adapters installed, which it does.
Any ideas on what I am doing wrong?
Thanks!
~B~

Hybrid SLI, read the mainboard manual if need to apply properly BIOS options.
Also read guides:
http://www.nvidia.com/content/hsli/configurator/assets/pdf/NVIDIA_Hybrid_SLI_User_Guide.pdf
http://enthusiast.hardocp.com/article.html?art=MTQ0NCwxLCxoZW50aHVzaWFzdA==
Make sure that you use latest drivers from Nivida as well.

K9n2 diamond boot up problems

hi all here we go
set up
k9n2 diamond
xilence quad sli 750 watt modular psu
4gb corsair
phenom 9850 black edition
hd3850 i know waiting for my gtx to come
ok switch on board lights up blue............... push power fans come on four lights glow red then it switches off no post
now i know the gpu works adn the memory is my board knackerd or the cpu

Quote from: Svet on 11-April-09, 22:24:56
Do >>Clear CMOS Guide<< with power cord removed after the CPU swap.
Also try to boot with one memory stick only in 1st DIMM near to CPU socket.
Make sure that CPU is seated properly to the socket too.
allready tried all that still cant get it to do anything apart from that 4200+ thats the only cpu i have had it posting on

K8N DIAMOND PLUS (sound problem)

Hi all.
I have a problem with my sound output.
I can only hear sound from my front left speaker and my woofer.
My speakers is Logitech Z-680.
My JAUD1 is jumped 5+6 and 9+10.
Windows settings is 5,1 surround and digital output since i use SPDIF optical!
My PSU is a seasonic S12 500w so that should give the power the board need!!!
anyone that can help me ???

Quote from: phionex00 on 03-May-06, 03:10:01
apologise i ment to post this in my own thread :shocking:hi Bas
ive just been reading a few threads from the Sticky Index - Find Answers Here Fast
and there saying that neo and diamond are shipped with a fault that they reqiure -5V and that systems with modern psu's that dont have the -5v rail the mob has to bee sent back are you aware of this ??
You are hijacking somebody elses post....stop doing this.....
Also the Diamond Plus isn't the same board as the Diamond.....
Do not reply to me, or I remove your posts! (Warning number 2)
@Microdk, could it be that a jumper isn't set right?
Just a wild guess.....

K9n2 diamond pcix sound sound

hi, sorry if this sounds daft. does the included sound card fit in the pci-x x1 slot (the one that means it's tight against my 8800gtx internal exhaust?) i tried it in the bottom sli slot but it didnt work, so i fitted my old se card to the pci slot
the 8800gtx kicks a load of heat out and i would imagine the vga or sound card very comfortable in this enviroment?
or did i miss something

Stu was seconds before me, but in words: No.
And I think a sound card can take - what can it be - 40-45C of hot air. Please remember that the impact of/expelled warm air is very "thin" or dissepated(?).
Second addition: If you have a good exhaust fan the hot air will go out that way. The PSU fan should help, too. Do not have a wall for less than ~half a meter behind these fans. It is quite important to have a clear path for the hot air to go out.

K9N2 Diamond & SLI Boot problem

Hello. I have a boot problem in my mb. My sli config is with 2 Gigabyte 8800 GT. I can enter windows and sli works fine. The problem is that i only have image in windows. I can't see post, so i can't access bios. Only when windows starts i get image. Tried the cards in a MSI K8N SLI Platinum and i had no problem. Image since i turn on computer. The cards in solo show image like in the MSI K8N. In bios i have the Hybrid SLI disabled, tried disable on-chip VGA but the pc won't boot. The customer service told me to update bios to version 2.3. I think that might be a bios beta version, i only know 2.1. There is a v2.2 to support the AM3 cpu's. Help !!

Quote from: 0125 on 18-September-09, 20:46:39
try to change the battery on your motherboard to see if it help. I believe that your battery of the motherboard is so weak so it won't able to show the POST.
The battery on the mainboard only powers the CMOS so it can store the BIOS settings. If the battery is failing, it will still start up, but BIOS settings will need to be re-set.

K9N2 Diamond 1066 memory problems.....

As you can see from my sig, I have four sticks of the exact same matched memory which have passed memtest. Now I just recentley upgraded to a Phenom II X4 955 BE and bios 2.4 so that I could run this processor. Now when I set in the cell menu to run at 1066mhz and reboot with my ram settings inputed, my system will post and hang at the post screen. I turn my system off and power back on and the same thing happens. I have to clear the cmos and restart in the bios. Now, if I set the system to 800mhz ungaged no problem just when I try it with 1066 Before this I had a Phenom X4 9950 that ran 1066 no problem it has only been since I got this new processor and bios. I do not get it, any suggestions.........

Memory controller is inside CPU.
Quote
Mushkin 1066mhz ddr2 4x 2gb memory
CPU can't handle all of them at full speed, use 800MHz, there is no performance difference anyway.

K9N2 Diamond - PWM Temperature Problems

On my setup my pwm temperature reading, under no load, is around 100C. At load it pushes 125C. My cpu temperature readings stay under about 35C. GPU temperature readings stay under 50C.
Any advice on how I can reduce the pwm temperature?
Only advice I can find with google is add another fan?
Thanks for any help.

Here is one link I found particularly insightful
http://www.tomshardware.com/forum/244894-29-temperature
From the site - PWM means Pulse Width Modulation. This generally refers to the voltage regulation around the CPU, which most often includes the mosfets.
PWM on the Abit IP35-Pro can go up to 100C before danger, but I wouldn't recommend anything over 60-70C or so. On the IP35-Pro, this is the area covered by the rainbow shaped heatsink.

K9N2 Diamond Problems

I was going to buy this board (MSI K9N2 Diamond) but it seems there are way too many issue's with it. Sound Drivers, 9950be compatibility using shipped bios, SLi, different video cards etc and other compatibility issue's. Problems going back to release and there is only one bios update! People using having to use Beta Bios? :huh:Have all these problems been fixed by MSI? Or will I have the same issue's if I buy the K9N2 Diamond now with a 9950be, Corsair Twinx 2x4096-8500c5df? I have had MSI's in the past wilt np but it sounds horrible if you buy this board. I don't care about SLi. Just want this board for all the other reason. Mainly can I use it with an Nvidia main card in 1st PCI-e x16, and an ATI AIW in the 2nd or 3rd PCI-e x16. Hope someone can help me. Has anyone bought this board and installed with this setup with no problems...... Out of box and no problems??? Everything working correctly? I'm scared to buy it!

http://global.msi.com.tw/index.php?func=prodcpu2&prod_no=1438&maincat_no=1#menu
The 9950 is supported.
Other then that, I don't see that many issues here in the forum with that board.
But if you are that worried, why not go with an MSI ATI chipset board?

K9N2 Diamond room occupied by sound card

I am interested in buying this new MSI technological masterpiece, K9N2 Diamond.
But one thing still bugs Me. The Creative® SB X-Fi Xtreme H/W Audio Card (MS-4132) would
be used underneath the VGA inside the PC case. My VGA is MSI NX8800GT Zilent 1G and as you know
or as you can see from MSI's web site in case if you didn't knew, it has very big cooler, almost as
big as another VGA. If the sound card is directly underneath the VGA in the PC case I think that it will be very difficult
for the Zalman cooler to do its job. I am not the technical support's specialist and that is why I am
posting the question :
Will My VGA NX8800GT Zilent 1G work with no problems at all with the K9N2 Diamond,
considering the fact that the sound card would be placed directly underneath the
VGA in the PC case ?
on this forum.
I hope I will receive direct answer from MSI's Technical Support team.

Quote
Will My VGA NX8800GT Zilent 1G work with no problems at all with the K9N2 Diamond,
considering the fact that the sound card would be placed directly underneath the
VGA in the PC case ?
Shouldn't be a problem

K9N2 Diamond problems installing Vista 64bit Raid Drivers

Hello everyone I have been having problems installing Raid Drivers during Vista 64 Install. The 32-bit drivers work fine and I can also set up Windows Vista 32 in Raid 0. But the same place where the " No CD/DVD drivers..." clause is will not let me use 64-bit Drivers. I have tried MCP72 and MCP73 raid drivers and neither is recognized. This is my setup.....
AMD Athlon 64 x 2 (3.2ghz) Black Edition
LiteOn Blu-Ray Player/Burner
LiteOn DVD/CD Burner
2 x 640 GB WD HDD
8gb (4 x 2gb Sticks) OCZ PC 6400 (DDR2 800) Ram
2 x Nvidia GeForce 9800 GSOs SLI
Xion 850w Modular Power Supply
K9N2 Diamond Motherboard
I am not using IDE at all, everything is Sata. So in BIOS I have IDE Controller off. I have the SATA port Set to RAID. I have no idea what I am doing wrong. I had this same setup on my K9N SLI Platinum board and it all worked fine. However every since I "upgraded" to this board I havent been able to install Vista 64 on my Array. I also have tried formatting the HDDs and I have tried setting up the Raid all over. Plz help me. This is my first post ever in a forum so if you need any info that I did not post here pls just let me know :D

By the way Here is my BIOS Settings:
- Standard CMOS Features
(None of my Hardware is Listed)
- Advanced BIOS Features
Full Screen Logo Display Enabled
Quick Booting Enabled
Hybrid SLI Support Disabled
Primary Graphics Adapter PCI-E
Boot Up Num-Lock LED On
IOAPIC Function Enabled
MPS Table Version 1.4
PCI Latency Timer 64
* CPU Functions
(None Available)
* Chipset Features
HPET Disabled
On-Chip VGA Disabled
* Boot Sequence
1st Boot Device BD Player
2nd Boot Device Raid Array
3rd Boot Device None
* Trusted Computing
TCG/TPM Support No
-Integrated Peripherals
USB Controller Enabled
USB Legacy Support Enabled
Onboard LAN Controller Enabled
LAN Option ROM Disabled
Onboard IEEE1394 Controller Disabled
Extra Raid/IDE Controller Enabled
Raid Mode RAID
HD Audio Codec Internal Codec
*On-Chip ATA Devices
On-Chip IDE Controller Disabled
PCI IDE BusMaster Disabled
On-Chip SATA Controller Enabled
RAID Mode RAID
- I/O Devices
COM Port 1 3F8/IRQ4
Not sure if this helps any but I just thought I would post it anyways :D

P6N Diamond sound problem

P6N Diamond has recently developed a sound problem. I am using Audioengine2 stereo speakers and the left speaker has started producing distortion (but no other sound) when switched on and connected to onboard Sound Blaster X-Fi Extreme audio. The right speaker works fine. Distortion is produced when the computer is booted and not just in windows. Both speakers and cables all work fine connected to my ipod so I assume the problem is with the P6N diamond onboard audio and not my speaker setup.
I have also tried reinstalling creative drivers and disabling and re-enabling sound blaster in device manager but the problem persists.
Many thanks in advance for any assistance provided.

Are you asking how do you power the system on with it out of the case? Are you able to connect front panel power switch to JFP1 or are the wires too short? If needed just take a small screwdriver or whatever and for 1 second or so short pins 6-8 together to turn system on. That would be the same as pushing the power button on the case.

X-Fi Xtreme PCIe Card MSI Edition(MS-4132) problem XP PRO SP3 K9N2 Diamond

Hello,
Need help with installation of driver for the X-Fi XP is finding the card but will not install. I went to Creative Web site and updater stated not supported device found to update need help..
K9N2 Diamond
XP Pro SP 3 32bit
Rosewill 1000W PSU
MSI N9800 Series SLI
Seagate sata 500GB X2

Have you tried installing the drivers from the MSI website?
The drivers are available >>here<<.
Also, make sure your motherboard drivers are installed properly and that there are no yellow exclamation marks in device manager as that would also explain why the sound card drivers won't install.

K9N2 Diamond Win 7 sound problem

Similar Messages

Maybe you are looking for