L2 Etherchannel Port Suspended issue

Hi All,
We're using 2 P2P link from different providers ( one 30 Mb and second 20 Mb) from Main POP to Remote POP.
We required load balance between both the P2P links with failover, but one of the port in suspended mode while channel-group apply.
Remote POP- Cisco 3400ME
Remote-POP-3400ME#sh int gi0/1
GigabitEthernet0/1 is up, line protocol is down (suspended)
Hardware is Gigabit Ethernet, address is 0016.9d26.5101 (bia 0016.9d26.5101)
Description: *** P2P-1 ***
MTU 9000 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 3/255, rxload 14/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 100Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:29, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 5681000 bits/sec, 757 packets/sec
30 second output rate 1306000 bits/sec, 531 packets/sec
127102505 packets input, 144344310802 bytes, 0 no buffer
Received 4570664 broadcasts (2231603 multicasts)
0 runts, 0 giants, 0 throttles
10 input errors, 10 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 2231603 multicast, 0 pause input
0 input packets with dribble condition detected
interface GigabitEthernet0/1
description *** P2P-1 ***
port-type nni
switchport trunk allowed vlan 1,3-4094
switchport mode trunk
load-interval 30
channel-group 21 mode active
end
Remote-POP-3400ME#sh int fas0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0016.9d26.5119 (bia 0016.9d26.5119)
Description: *** P2P-2 ***
MTU 1546 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 4/255, rxload 28/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:24, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 11147000 bits/sec, 1390 packets/sec
30 second output rate 1944000 bits/sec, 1112 packets/sec
5404734 packets input, 1041290192 bytes, 0 no buffer
Received 4924815 broadcasts (2259127 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 2259127 multicast, 0 pause input
0 input packets with dribble condition detected
interface FastEthernet0/23
description *** P2P-2 ***
port-type nni
switchport trunk allowed vlan 1,3-4094
switchport mode trunk
load-interval 30
channel-group 21 mode active
end
====================================================================
MAIN POP- cisco 3750
MAIN-POP-3750-STACK#sh int gi2/0/7
GigabitEthernet2/0/7 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0019.e78b.c607 (bia 0019.e78b.c607)
Description: *** P2P-1 ***
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 6/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 100Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 3/75/0/0 (size/max/drops/flushes); Total output drops: 103937
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 2660000 bits/sec, 2181 packets/sec
30 second output rate 27366000 bits/sec, 2723 packets/sec
31887654718 packets input, 10045858003774 bytes, 0 no buffer
Received 467095011 broadcasts (214841125 multicasts)
0 runts, 27 giants, 0 throttles
22 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 214841125 multicast, 406425160 pause input
interface GigabitEthernet2/0/7
description *** P2P-1 ***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,3-4094
switchport mode trunk
speed 100
load-interval 30
channel-group 21 mode active
MAIN-POP-3750-STACK#sh int gi2/0/10
GigabitEthernet2/0/10 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0019.e78b.c60a (bia 0019.e78b.c60a)
Description: *** P2P-2 ***
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 100Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 2449
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 2000 bits/sec, 4 packets/sec
30 second output rate 55000 bits/sec, 62 packets/sec
13820128 packets input, 4202349171 bytes, 0 no buffer
Received 2375120 broadcasts (810650 multicasts)
0 runts, 0 giants, 0 throttles
15 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 810650 multicast, 478680 pause input
0 input packets with dribble condition detected
28535531 packets output, 16494317102 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
interface GigabitEthernet2/0/10
description *** P2P-2 ***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,3-4094
switchport mode trunk
load-interval 30
channel-group 21 mode active
Please advise me to fix the issue and we are able to achieve and use with load-balance via etherchannel.
Thanks in ADV,

Hi Inayath,
Remote POP - Cisco 3400
%EC-5-CANNOT_BUNDLE2: Fa0/23 is not compatible with Gi0/1 and will be suspended (MTU of Fa0/23 is 1500, Gi0/1 is 9000)
FastEthernet0/23 is up, line protocol is down (suspended)
Hardware is Fast Ethernet, address is 0016.9d26.5119 (bia 0016.9d26.5119)
Description: *** P2P-2 ***
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:11:15, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 56000 bits/sec, 65 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
658410 packets input, 573817450 bytes, 0 no buffer
Received 202028 broadcasts (92075 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 92075 multicast, 0 pause input
0 input packets with dribble condition detected
333031 packets output, 77587439 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
GigabitEthernet0/1 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 0016.9d26.5101 (bia 0016.9d26.5101)
Description: *** P2P-1 ***
MTU 9000 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 3/255, rxload 30/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 100Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:16, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 12136000 bits/sec, 1230 packets/sec
30 second output rate 1557000 bits/sec, 921 packets/sec
3730111 packets input, 4532149684 bytes, 0 no buffer
Received 189538 broadcasts (88491 multicasts)
0 runts, 7 giants, 0 throttles
20 input errors, 13 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 88491 multicast, 0 pause input
0 input packets with dribble condition detected
2663637 packets output, 494552940 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out

Similar Messages

Home Hub 3 Port Forwarding Issue - Question to BT

Question to BT
Hello i have recently joined BT Infinity and have hit the issue of the Port Forwarding not working. My HH3 is on the following version of software. Will this version automatically upgrade to the latest version of firmware and will this fix my port forwarding issue?
As i work in IT (Cisco Network Eng) i need to be able to access several devices/services at home and this is a real pain for me. If you think that this could drag on as some posts have indicated could you please let me know and i will either get a draytek or throw in a cisco 1841.
Thank you
Dean.
Current firmware:
V100R001C01B031SP09_L_B
Last updated:
Unknown

requiem wrote:
Question to BT
Hello i have recently joined BT Infinity and have hit the issue of the Port Forwarding not working. My HH3 is on the following version of software. Will this version automatically upgrade to the latest version of firmware and will this fix my port forwarding issue?.........
Thank you
Dean.
Current firmware:
V100R001C01B031SP09_L_B
Last updated:
Unknown
Hi Dean
By the look of it you've got the type B version of the HH3 with current firmware.
From http://bt.custhelp.com/app/answers/detail/a_id/13073
The latest versions of the firmware are:
BT Home Hub 3 – Software version 4.7.5.1.83.8.57.1.3 (Type A) or V100R001C01B031SP09_L_B
Please Click On any Text in Blue as that automatically links to information.
PC (NDEGR)

Quantum Gateway Port Forwarding issues

This post can be removed.... the port forwarding worked once I set it up under "Advanced Settings -> Network Settings ->Port Forwarding" instead of "Firewall -> Port Forwarding"
Hello,
I am having an issue setting up port forwarding. I have made several attempts to make port forward TCP 8096, but it continues not to work. I had it working with no problems at my with my old router before we moved so I know it's not an issue with my computer firewall or antivirus and MediaBrowser is working fine on the local network. Is anyone else experiencing Port Forwarding issues? Also when will DMZ be enabled on this gateway?
Any help would be apprciated. I'm trying to setup MediaBrowser so I can schedule recordings when i'm not at home.
Thanks!
Armyb77
This post can be removed

See kayster contribution here.
SYNOLOGY DS214 - Remote access via BT Home Hub
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Cat 3750-Span (Port Mirroring issue)

Hello team
I am facing port mirroring issue in my setup. Details of the setup are mentioned below
Setup--
Stack of 4 catalyst switches WS-C3750X-48P running software 15.0(1) SE3 .Approximately 12 vlans are configured in this setup and port mirroring is done for all vlans with destination configured as single Gig Ethernet port...The setup works fine from mirroring perspective for 3-4 days and after that machine connected to destination port stops getting data.
Observations-
It has been observed that during the issue, the port configured for mirror destination has lot of packet drop/input errors on the port statistics.
If we configure only TX packet mirroring, it works for 8 -10 days
If we configure TX & RX packet mirroring, it works for 2-3 days
Testing done
Tried clearing counter on destination port but no success (mirroring doesn’t start)
Tried shut /no shut for the destination port but no success.
Tried restarting the machine connected to destination port but no success
Workaround
We need to reconfigure the mirroring configuration after removing the mirroring config from the switch. Once the same is done, mirroring starts working.
Want to understand
1-is there any HW limitation for the switch (destination port not capable of handling mirroring traffic)
2-is there any software related issue?
3-what can be permanent resolution for the same..

Hello
We have tried this previously but found same result.
1- we deleted the monitror session and recreated again with same session number
2-we deleted the monitor session and created new session (session id diffrent ) with same config..
in both cases its working for 3-4 days..

Post Moved Mac Port Forwarding Issues

Post Moved to Other BB Queries http://community.bt.com/t5/Other-BB-Queries/Mac-Port-Forwarding-issues/td-p/550779
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Does this help...?
http://community.bt.com/t5/Other-BB-Queries/Port-forwarding-and-Loopback-DO-work-YMMV/m-p/538328

OC4J port binding issue

This thread is in OC4J/J2EE forum, but it feels like it could be an Redhat AS2.1 port handling issue, so I'm copying here...
I'm having some problems with OC4J standalone. Starting and stopping OC4J gives error:
"Error starting HTTP-Server: Address already in use"
and sometimes "Error starting ORMI-Server. Unable to bind socket: Address already in use
and almost always "Error starting JMS-Server: Unable to bind socket: Address already in use
Starting and stopping a few times usually results in a successful restart, but this is intermittent success and not predictable. Reallocating with a different port numbers means successful start fist time, but then it follows the same pattern.
This is OC4J standalone 9.0.3 pure java deployed on Linux RHAS 2.1...
Java version is 1.3.1.1_02-b02
My start and stop scripts look like this :
startoc4j.csh
#!/bin/csh
java -Xmx100m -Xms100m -Dscm.logon=true -jar oc4j.jar -userThreads &
stopoc4j.csh
#!/bin/csh
java -jar admin.jar ormi://localhost:50501 admin ias_admin1 -shutdown
Has anyone seen this before? Is there a standard start / stop script for OC4J standalone on UNIX that I can use?
Thanks,
Mark

This was found to be a JRE on Linux bug. Solution was to upgrade to Javasoft 1.4.1...

NX-OS 5.0(3)N2(1) vpc orphan-port suspend

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/layer2/503_n2_1/Cisco_n5k_layer2_config_gd_rel_503_N2_1_chapter8.html#task_35CE3B4AEE75485AB7A22C3A085D2F99
Suspending Orphan Ports on a Secondary Switch in a vPC Topology
You can suspend a non-virtual port channel (vPC) port when a vPC secondary peer link goes down. A non-vPC port, also known as an orphaned port, is a port that is not part of a vPC.
interface ethernet slot/port
vpc orphan-port suspend - "Suspends the specified port if the secondary switch goes down."
Do I apply this command only to orphan-ports on the vPC Secondary N5K? Or, since a vPC Primary could become a vPC Secondary, should I apply the command to all ports, on either N5K that are orphan ports?
-bill
http://billyc5022.blogspot.com/

I just tested this in the lab and indeed , you can't configure it on the FEX ports. But -as you mention indeed- you can have a VPC on the FEX ports that will follow the default vpc behaviour.
So the correct workaround is then to apply it on all host ports of the FEX :-) (except the VPC ones)
Lets see if that works:
NEXUSB# sh run int eth100/1/1
!Command: show running-config interface Ethernet100/1/1
!Time: Thu Aug 18 15:41:55 2011
version 5.0(3)N2(1)
interface Ethernet100/1/1
vpc orphan-port suspend
switchport access vlan 100
spanning-tree port type edge
yes , that works !
when peer link fails:
NEXUSB# sh int status
Port          Name               Status    Vlan      Duplex Speed   Type
Eth1/1        --                 vpcPeerLn trunk     full    1000    10g <-- this is a vpc, down on secundary, peer link failure
Eth1/2        --                 sfpAbsent 1         full    10G     10g
Eth1/3        --                 connected 1         full    10G     10g     <--- this is my single connected FEX fabric port, stays up
Eth1/4        --                 sfpAbsent 1         full    10G     10g
Eth1/5        --                 sfpAbsent 1         full    10G     10g
Eth1/6        --                 sfpAbsent 1         full    10G     10g
Eth1/7        --                 vpcPeerLn trunk     full    1000    10g <--- this is a single connected blade switch, goes down, as "orphan port suspend"
Eth1/8        --                 sfpAbsent 1         full    10G     10g
Eth1/9        --                 sfpAbsent 1         full    10G     10g
Eth1/10       --                 sfpAbsent 1         full    10G     10g
Eth1/11       --                 sfpAbsent 1         full    10G     10g
Eth1/12       --                 sfpAbsent 1         full    10G     10g
Eth1/13       --                 sfpAbsent 1         full    10G     10g
Eth1/14       --                 sfpAbsent 1         full    10G     10g
Eth1/15       --                 sfpAbsent 1         full    10G     10g
Eth1/16       --                 sfpAbsent 1         full    10G     10g
Eth1/17       --                 notconnec trunk     full    10G     10g
Eth1/18       --                 sfpAbsent 1         full    10G     10g
Eth1/19       --                 sfpAbsent 1         full    10G     10g
Eth1/20       --                 sfpAbsent 1         full    10G     10g
Po10          --                 noOperMem trunk     full    10G     --
Po30          --                 noOperMem trunk     full    1000    --
Po100         --                 connected 1         full    10G     --
mgmt0         --                 connected routed    full    100     --
Eth100/1/1    --                 vpcPeerLn 100       full    auto    --         <- this is my fex server interface, also going down as orphaned port suspend :-)
Eth100/1/2    --                 notconnec 1         auto    auto    --
If you put this in a port profile, it can be added automatically:
NEXUSB# sh port-profile
port-profile FEX-SERVER-PORT-DEFAULT
type: Ethernet
description: SRV FEX-DEFAULT
status: enabled
max-ports: 512
inherit:
config attributes:
duplex auto
no cdp enable
vpc orphan-port suspend
regards,
Geert

WRTU54G-TM Port Forward issues, DHCP server disabled but still gives out addresses

I've seen other posts about port-forwarding issues. I've had to hard-reset the device twice in 2 months to clear this up.
One issue that I can't figure out at all is that the DHCP server gives out addresses when it is set to disabled. This is a problem because it gives out the public DNS servers, which will not resolve addresses on my LAN. Anyone else seen this?
Anyone had success putting this router behind a better one and still getting the phone SIM to register and work?

Have you tried to upgrade the firmware on your Router?
Click Download the latest firmware for your Router and save the Firmware file on your Desktop.
Once you Download the firmware for your Router, Now you need to login to the Router setup page and click on the "Administration" tab and below click on "Firmware Upgrade" and then click on the Browse Button and select the firmware file and click on Upgrade.
Once the firmware is upgraded successfully then you need to Reset your Router and Re-configure all the settings on your Router from scratch.

EtherChannel & Port Aggregation different ?!?

hi frens,
i quite confuse in the EtherChannel & Port Aggregation technology... and how they related in perform load balancing ??
Thanks
William

Hi William,
Etherchannel and Port Aggregation are two terms that mean the same thing. Etherchannel is 'Cisco terminology' and Port Aggregation and link bundling are generic terms.
HTH,
Bobby

Etherchannel and port suspended

hi all,
i created an etherchannel on my 4507 leading to a 3750. i did it the way i always do that works. when i put a specific port into the channel, it goes into "suspended" line protocol. what does this mean?

Etherchannel
"Some messages from the switch might look like errors but are part of the normal EtherChannel process. For example, as a new port is configured as a member of an existing EtherChannel, you might see this message:
4d00h: %EC-5-L3DONTBNDL2: FastEthernet0/2 suspended: incompatible partner port with
FastEthernet0/1
When the port first is added to the EtherChannel, it is incompatible because the STP runs on the channel and the new port. After STP takes the new port through its progression of states, the port automatically is added into the EtherChannel.
Other messages do indicate a port-compatibility error. In these cases, the cause of the error is shown. For example, the following message tells that FastEthernet0/3 has a different duplex mode than the other ports in the EtherChannel:
4d00h: %EC-5-CANNOT_BUNDLE2: FastEthernet0/3 is not compatible with FastEthernet0/1
and will be suspended (duplex of Fa0/3 is full, Fa0/1 is half)
Are you sure you have the same configs on each side?
Vlad

Port-Channel Issue: SP-5-CANNOT_BUNDLE_LACP

I'm having an issue with the port-channel coming up. Right now it's "down down". I'm not really sure why. All other port-channels on the 6500's in VSS work fine. This one seems to be giving me an issue though.
-Both interfaces that are using this port-channel are "up up".
-I've done "shut's, no shut's" on all interfaces involved.
sh etherchannel summary
Flags: D - down        P - bundled in port-channel
        I - stand-alone s - suspended
        H - Hot-standby (LACP only)
        R - Layer3      S - Layer2
        U - in use      N - not in use, no aggregation
        f - failed to allocate aggregator
        M - not in use, no aggregation due to minimum links not met
        m - not in use, port not aggregated due to minimum links not met
        u - unsuitable for bundling
        d - default port
Po4(SD)         LACP      Gi1/1/4(I)     Gi2/1/4(I)
interface Port-channel4
switchport
switchport access vlan (vlan number)
switchport mode access
load-interval 30
flowcontrol receive desired
spanning-tree portfast edge
end
interface GigabitEthernet1/1/4
switchport
switchport access vlan   (vlan number)
switchport mode access
load-interval 30
flowcontrol receive desired
spanning-tree portfast edge
channel-protocol lacp
channel-group 4 mode active
end
interface GigabitEthernet2/1/4
switchport
switchport access vlan (vlan number)
switchport mode access
load-interval 30
flowcontrol receive desired
spanning-tree portfast edge
channel-protocol lacp
channel-group 4 mode active
end
sh log
149886: Jul 3 15:20:34 CDT: %EC-SW1_SP-5-CANNOT_BUNDLE_LACP: Gi2/1/4 is not compatible with aggregators in channel 4 and cannot attach to them (flow control receive of Gi2/1/4 is desired, Gi1/1/4 is on)
149887: Jul 3 15:20:35 CDT: %EC-SW2_SPSTBY-5-CANNOT_BUNDLE_LACP: Gi2/1/4 is not compatible with aggregators in channel 4 and cannot attach to them (flow control receive of Gi2/1/4 is desired, Gi1/1/4 is on)
Thank you for your help.

HI Mark,
1. Can you please check your ethernet card ...where this port channel connected..on the server.
    may be there are 2 different card.
2. from cisco websites:
Error Message
Explanation
This port has different port attributes than other ports within the port channel.
Recommended Action
Match the port attributes to that of the port channel.
Regards
Please rate if it helps.
Match the port attributes to that of the port channel.This port has different port attributes than other ports within the port channel.
EC-5-CANNOT_BUNDLE_LACP: [char] is not compatible with aggregators in
channel [dec] and cannot attach to them ([char])

USB Port Suspended

Hi, I am having a similar issue to the one described in this post: https://discussions.apple.com/thread/2443010?tstart=0
One of my usb ports on my Macbook Pro (13" late 2011) no longer work. It is the usb port beside the lightning/mini display port the usb port beside the SD card slot still works fine. I belive it was caused by some sort of surge from a usb hub that I had plugged into the port when it stopped working (I belive this is so because the surge protector that I had the usb hub's external power adapter plugged into was turned off.). I have used the usb probe tool to discover that the device has been suspended.
I have tried resetting the smc and restarting my laptop. I will also reset the pram and report back later.
Please help. I am really hoping this is not a hardware problem but that is what it seems to be. Also if it is a hardware problem is it possibel to fix myself? And hwo much would a repaire such as this one cost me?
Any advice or suggustions are greatly appreciated.

By saying "the device i suspended", I mean the usb port. my bad

NVIDIA brightness and suspend issues on VAIO

Hello,
I have problems with NVIDIA driver (assuming) and I searched similar topics on forum but still couldn't solved. I'm on ARCH 3.1.5 Xfce, installed nvidia-290 proprietary driver and nvidiabl from AUR. No swap partition and using lightdm. Laptop model is VAIO VPCF132FX, resolution at 1600x900.
blank screen when switching to tty1 - tty6 but I can run commands in virtual consoles (tried log in and reboot from tty1 not seeing just typed). I added vga=xxx in grub kernel line and it's changing resolution while booting but switch to ttys still gives blank screen. I think it's happening after started X. If I doesn't start Xfce I can switch.
can't resume from suspend. I think it suspends successfully and when try to back it freezes, no inputs from keyboard (tried some shorcuts, numlock, password etc) and blank screen. After few seconds fan reaches at it's loudest and I ended up with 5sec turn off. Is it hardware related issue or kernel (or X lightdm Xfce). Should I use laptop-mode-tools to get suspend work or missing something?
if I added
Option "RegistryDwords" "EnableBrightnessControl=1"
to "Device" section in xorg.conf, keyboard shortcut of brightness and brightness-applet are working. It has 8 level of brightness and only top 3 of them works properly, if it gets lower from there screen blinks few seconds and back to highest brightness. I removed that line from xorg.conf, installed nvidiabl it works great except keyboard shortcut and brightness applet. How do I get shortcut and applet work on Xfce with nvidiabl? Also shortcut is working when numlock is off, is there any chance to work either numlock on or off?

Hi Dave, see if this might be of use...
Go to System Preferences > Universal Access and down in the Display: section make sure that the Enhance contrast: slider is all the way to left to Normal, or more to the right for less Contrast.

Win 8.1 shudown and suspend issue on Thinkpad E520

Hi,
I just do a clean install of Win 8.1 with iso. Install all driver Win 7 or Win 8 when no driver for win8.1 is available on lenovo or intel website. No error on devices management. try to shudown computer, the screen came black but i can here the fan and red light stay on... wait a moment, seems my notebook can't shudown correctly. Googling on this issue give to disable "fast shutdown" in power management. Try to shutdown now ok no problem. but the suspend mode give the same issue as a fast shutdown, notebook came black but red light stay up and i have to force the shutdown by pressing the button power for several second.
The notebook is not indicate as compatible and or incompatible from this list : http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?DocID=HT079684
.Is there way to resolve this issue ?
Bye

Hi,
I just do a clean install of Win 8.1 with iso. Install all driver Win 7 or Win 8 when no driver for win8.1 is available on lenovo or intel website. No error on devices management. try to shudown computer, the screen came black but i can here the fan and red light stay on... wait a moment, seems my notebook can't shudown correctly. Googling on this issue give to disable "fast shutdown" in power management. Try to shutdown now ok no problem. but the suspend mode give the same issue as a fast shutdown, notebook came black but red light stay up and i have to force the shutdown by pressing the button power for several second.
The notebook is not indicate as compatible and or incompatible from this list : http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?DocID=HT079684
.Is there way to resolve this issue ?
Bye

Ethernet Port Software Issue

A few weeks ago, I noticed that my ethernet port was not working. It would not recognize when a cable was plugged in. This came along with a startup issue, so when I took it into the apple store to have it looked at, they replaced the logic board. It fixed the startup issue, so I assumed that it fixed the ethernet issue. I have now realized that it didn't. So I took it back to the apple store and they booted my computer from a separate drive, and the ethernet port worked just fine. So, the genius told me, the port problem is a software issue. He told me to reinstall leopard and that it should fix it. It didn't. So my ethernet port is not working because of a software issue. Does anybody know where to start? Thanks!

One way to test it is to configure it via the Unix back end. From a terminal window (you have to be root to do this, or prefix every command with sudo):
ifconfig en0 192.168.16.12 255.255.255.0 up
route add default -net 192.168.0.0 192.168.16.1 255.255.0.0
Substitute your own numbers for the correct addresses and subnet mask. The address on the ifconfig line is for your ethernet interface. The one in the route line is your default gateway.
Then type:
ifconfig en0
and it will show how the ethernet port is configured. Be sure the address and subnet mask are correct.
netstat -r
and it should show the routing table, including the default route you added, bound to the en0 interface.
Then try using the network. If it works correctly, it's a software issue.

L2 Etherchannel Port Suspended issue

Similar Messages

Maybe you are looking for