LAP1231G to Autonomous mode

I followed instruction from cisco web site to change LAP1231G to autonomous mode without controller. I get follwing error message when AP tries to connect local tftp server.
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1200-k9w7-tar.default
examining image...tftp://255.255.255.255/c1200-k9w7-tar.default: permission denied
ERROR: Failed to open archive file tftp://255.255.255.255/c1200-k9w7-tar.default
Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"
I checked permission and with tftp server on linux windows. Still get the same error msg.
Thanks for Help in Advance

Yes, My AP model is AIR-LAP1231G.
I have figured out the error and have resolved it. The issue was with renaming the file. I renamed using windows rename (F2) that appended .tar extension after default (c1200-k9m7-tar.default.tar) later I renamed using CLI then it worked fine.
small thing gave big trouble
Thanks scott

Similar Messages

  • Steps to convert access point from LightWeight mode to Autonomous mode

    I need steps to convert the following access point from Lightweight mode to Autonomous mode
    AIR-AP1242AG-E-K9
    Regards,
    Majid

    Hi Majid,
    The method is just hidden a little further down the doc that Scott linked (+5 points Scott :)
    Using a TFTP Server to Return to a Previous Release
    Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 On the PC where the TFTP server is located, perform these steps:
    a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
    b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
    Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
    Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 6 Disconnect power from the access point.
    Step 7 Press and hold MODE while you reconnect power to the access point.
    Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    Hope this helps!
    Rob

  • 1131 LAP in autonomous mode

    I was setting up the APs for a new users lab when we discovered they had puchased LAPs instead of APs.
    I installed the current version of the IOS following the procedures outlined in "Converting a Lightweight Access Point Back to Autonomous Mode" on Cisco's website. However, they're just not behaving correctly.
    Before going further, can LAP1131s be converted to autonomous mode? Or is it only AP1131s that can be converted back and forth?
    Thanks,
    Chris

    Hi Chris,
    One thing to note that on the newer IOS's the Radio's cannot be enabled until the SSID is set. You may have been seeing this result;
    Changes to the Default Configuration-Radios Disabled and No Default SSID
    In this release, the radio or radios are disabled by default, and there is no default SSID. You must create an SSID and enable the radio or radios before the access point will allow wireless associations from other devices. These changes to the default configuration improve the security of newly installed access points.
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b38jebrn.html#wp147963
    Hope this helps!
    Rob

  • Cisco 3502i in autonomous mode - for site survey

    Hi,
    Last year I was able to load autonomous mode IOS to a cisco 3502i to do the site survey using instructions at following thread.
    https://supportforums.cisco.com/thread/2084624
    This year I have to do site survey for a different site and need to do the same process. However on the CCO I don't see the autonomous image. Under downloads -> products -> wireless -> access points -> Cisco 3502i I see IOS link and when clicked there is gives
    ap3g1-k9w8-tar.124-23c.JA4.tar. I even loaded that IOS but it seems to be light weight mode IOS.
    After reading a few different threads somebody clarified that K7 = IOS and K8 = Lightweight. However I can't seem to find the lightweight mode anywhere.
    https://supportforums.cisco.com/thread/2140629
    Can somebody guide me? I need to run this code only for the site survey and totally understand the fact that Cisco would not support such configuration.
    Thanks in advance,

    Sorry to inform you but there is no autonomous code for the 3500. You could however use the 1140 code. But this not supported by Cisco but it does work ..
    Sent from Cisco Technical Support iPhone App

  • Embedded AP Autonomous Mode

    Guys,
    I'm having trouble booting my embedded AP in a 890w router into autonomous mode.  When I configure it with an IP and connect to it via the session manager, the config is default but the AP appears to be in lightweight mode.  I only have a limited command set (e.g. no Configure terminal) and the console shows messages about it trying to discover a WLC.
    I've set the following command on the CLI of the router:
    service-module wlan-ap 0 bootimage autonomous
    and reset the AP but still the same.
    My boot image is ap802-k9w8-mx.152-4.JB4.  AS I understand it this should be an autonomous image but is this maybe part of the issue?
    Any ideas on how I can get the embedded AP to boot into autonomous mode?
    Thanks!

    Hey Bart,
    Unfortunately I don't have that archive command available in the CLI, I'm guessing this is down to the list of available commands in the lightweight image.
    I've tried to copy down the image from ROMMON by setting a manual IP and copying the image from a tftp server on the same subnet but the traffic isn't getting to the tftp server i.e.
    ap: set
    DEFAULT_ROUTER=10.0.3.254
    IP_ADDR=10.0.3.253
    NETMASK=255.255.255.0
    Then configured a PC with TFTP server on the same subnet and placed in the same subnet as the AP:
    interface FastEthernet0
    switchport access vlan 300
    interface wlan-ap0
    description Service module interface to manage the embedded AP
    ip unnumbered Vlan300
    interface Wlan-GigabitEthernet0
    description Internal switch interface connecting to the embedded AP
    switchport access vlan 300
    interface Vlan300
    ip address 10.0.3.254 255.255.255.0
    Say I configure the PC with TFTP as 10.0.3.1/24 I cannot get connectivity between the AP in ROMMON and the PC.  Should this work okay?
    Thanks.

  • Autonomous mode 1242AG

    We do not wish to use a controller and simply wish to plug our APs into a network switch. I understand that I need to revert the APs back to Autonomous mode, as LWAPP always looks for a controller? ...
    I have obtained c1240-k9w7-tar.default, and attempted to upload to the AP via solarwinds TFTP, the server can see the AP (both 10.0.0.1 and 10.0.0.2) but it keeps timing out on the upload, I have tried a straight-through and a cross-over cable but to no avail ...
    Any help would be appreciated, thanks

    TFTP usually fails because of file name mismatches or path mismatch.
    The filename you request must *exactly* match, spelling and case "abcde" and Abcde" and ABcde" are three different files as far as TFTP are concerned; the pathname must also be exact, including case.
    Also make sure you set up Solarwinds to point to the directory containing the file, then reference it as a "root" directory in your TFTP request (i.e., even though the file is in C:\Temp\Cisco, you reference it from TFTP as tftp///)
    Also note that Solarwinds has a file size limitation (as do most TFTP servers) of ~32Meg. 3COM's 3Cdaemon VERSION 2.x does NOT have the 32 Meg limitation.
    If you search the forums, Rob Huffman has described a condensed version of the instructions for recovering an AP and / or switching it back to Automomous mode.
    Good Luck
    Scott

  • 1552E in Autonomous Mode

    Gents,
    I need some help understanding if it is possible to run two 1552E APs in Autonomous mode? And if there is a good document to read to help in configuring the APs in this mode.
    Finally, if running the 1552E in Autonomous mode is doable, do you see any problem using the two APs to bridge traffic between 2 buildings? I can add more details on what am trying to do once i get some feedback.
    Thanks in Advance,
    A

    Please refer similar discussion
    https://supportforums.cisco.com/discussion/12026436/autonomous-wireless-point-point-bridge

  • Cisco Aironet 1200 LAP Issues - LAP to Autonomous Mode

    Greetings! After purchasing 4 of the Cisco Aironet 1200 G Series WAPs, I'm now running into a slight issue with them.
    I received these last week with the understanding that if I didn't have the Cisco controller device, I could convert them from being the Lightweight Access Point, back to Autonomous mode with an IOS.
    With this, I checked the documentation that came with the device and found the "Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode" or http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&needs_authentication=yes&CommCmd=MB%3Fcmd%3Dadd_discussion%26mode%3Dshow%26needs_authentication%3Dyes%26location%3D.ee7c7c3.
    From there, I followed the instructions listed under Converting a Lightweight Access Point Back to Autonomous Mode. Before the rename of the file, I checked the device and found AIR-LAP1242G-A-K9 for the Model No.
    One of the Cisco Certified admins here was able to obtain the latest build for the IOS for the device or c1240-k9w7-tar.123-8.JEB1.tar. Per the instructions, I renamed the file to coincide with the model of the device.
    I followed the instructions from there, and it looked as if everything was going well. However, after the upgrade, I'm running into an issue with the following:
    File "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1" uncompressed and installed, entry point: 0x3000
    executing...
    At this point, the device just locks up. All lights are lit green on the device. According do the documentation, it should reboot and from there, I should be able to access the web interface by IP.
    I've tried to perform the upgrade again using the same IOS build, but the same thing happens with the lock up.
    At this point, I'm assuming the issue is with the build of the IOS that I have and I may have to look at getting an older build. However, before doing so, I thought I would post something here to see if anyone had an idea.
    I may have needed to refine my searching of the forums, but wasn't able to find anything in relation to my issue. If there is something out there, I do apologize for the post and will happily refer to any current information.
    If you need any further information in relation to this, please let me know. Any assistance is greatly appreciated. Thank you!

    Hi Jeffrey,
    Reverting the Access Point Back to Autonomous Mode
    Have a look at Step 3
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
    Using a TFTP Server to Return to a Previous Release
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
    Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 5 Disconnect power from the access point.
    Step 6 Press and hold MODE while you reconnect power to the access point.
    Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    Hope this helps!
    Rob

  • Convert from LAP to autonomous mode issue

    I bought some after market 1242's for extended coverage in my warehouse. The current 1242's I have are all set up in autonomous mode.
    When I console into the AP's I bought they are looking for a CAPWAP -Controller obviously from the previous environment. There is nothing on the AP or in the sh version showing LAP. 
    *Mar  1 00:46:37.102: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:46:38.104: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.xxx
    *Mar  1 00:46:38.106: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.xxx
    *Mar  1 00:48:38.106: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    #sh version
    #Version 12.4(21a)JA2
    System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
    I cant seem to be able to reset these to where they aren't looking for the Controller. I can login with the default username and password Cisco/Cisco but I cant do an erase. I get the privileged command prompt but cant do erase star or a config t??? Is there something I'm missing here that I need to to?
    So far these commands have worked::
    debug capwap console cli
    debug capwap client no-reload
    So can I downgrade or go back to autonomous mode or do I have to reload an IOS again? I don't have a license so my options there are limited.
    Any ideas??? Thanks

    HI,
    As pe your post:
    System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
    This is lightweight image. for this image you need controller.
    If you want to use as autonomous AP. Then you must convert it to Autonomous mode.
    Autonomous image code : k9w7
    More about images:
    http://rscciew.wordpress.com/2014/01/04/understand-access-point-ios-images/
    Here is the procedure to convert to autonomous :
    https://supportforums.cisco.com/document/57476/lwapp-autonomous-conversion-and-vice-versa-access-points
    http://paulbeyer.wordpress.com/2010/01/16/converting-a-cisco-ap-from-lwapp-to-autonomous-mode/
    http://www.youtube.com/watch?v=QQ_NuxdRhQ4
    Regards
    Dont forget to rate helpful posts

  • Status of 1131ag in Autonomous Mode

    Hello,
    I have a few 1131ag APs that I'm using in Autonomous Mode.  I've configured and everything looks fine but the "mood ring" is yellow.  I've worked with these previously in lightweight mode and know they should be green.
    What does the yellow status light indicate?
    Thanks.
    John

    I guess POE could be the issue.  The AP is using POE from the switch and appears to be working fine otherwise.  I 'm trying to find anything or direction where to look for possible causes other than "Ethernet Link".  I've even seen devices associating with the AP.
    I swapped cables, turned off PoE and used the power cord but still not getting the green status on the top of the AP.
    Another update:  Everything appears to be functional with the AP.  It would be nice if there were color samples to go with the chart.  I've had others look and get a mixed bag of "It's yellow" and "It's green".

  • 3702 Support full functionality in Autonomous Mode

    Does the 3702 , 2702 and 1702 support full functionality in Autonomous mode?  i know there was a limited Site Survey function but wondering if they have added full function for these APs?

    Yes it does and also check the table below , both firmware are shown LAP and Autonomous for supported APs including 3700 series. 

  • Trying to setup 1131 in autonomous mode with multiple ssids and vlans

    hi there,
    I'm trying to setup an aironet 1131 in autonomous mode with a WLAN for each VLAN.
    I can connect to the SSID "BLUGstaff" but I don't pick up a DHCP address and when I set a static IP I can't anything on the vlan so I can only assume I have made an error.
    I have attached the config for the access point.
    The switch port the access point connects to has the following config...
    interface FastEthernet1/0/3
    description ## Access Point ##
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 121
    switchport trunk allowed vlan 1,121-124
    switchport mode trunk
    spanning-tree portfast
    end
    Can anyone explain what I've done wrong? Thanks in advance for any help,
    Huw

    Hello Huw,
    as i see in your confirguartion.
    native VLAN is 121. so you have to correct following in your AP configuration
    1) interface Dot11Radio0.121
    encapsulation dot1Q 121 native
    bridge-group 121         ->>>>>>>>>>>>>>>> change this to brige-group 1 , native always tied to bridge group 1
    2)
    interface FastEthernet0.121
    encapsulation dot1Q 121
    add also under this sub interface
    bridge-group 1
    please let me know how it goes.
    Kind regards
    Talal
    ==========
    please rate answers that you find useful , and mark as answered - when it is :-) - so others can find it easily

  • Problems with DHCP and virtual PC connected to an AP in autonomous mode

    I've a virtual machine (Windows 7) on my MacBook running on VMWare Fusion 6 running in bridge mode and can't get an IP address from my DHCP server. NAT mode in VMWare is working, but not an option.
    I've tracked down the problem with Wireshark to the DHCP Offer that is dropped by the Cisco AP:
    On the LAN side I've captured the packets and could see that the DHCP-DISCOVER from the Windows client was answered by the DHCP server with a DHCP-OFFER (all these packets are broadcasts in the same layer 2 network), but the OFFER was not forwarded by the 1142 AP running in autonomous mode, version 15.2(4)JA.
    The problem looks to be similar to a previous discussion with WLCs where a solution is available meanwhile, see:
    https://supportforums.cisco.com/discussion/11350776/dhcp-issue-inside-vm-connected-wireless-network
    http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_01110010.html#ID2828
    Is there any solution for APs running in autonomous mode?
    Jan

    It's already a while ago, but recently I got a new router at home and have upgraded the AP to 15.3(3)JAB as well. I'm not sure what the exact reason was, but the problem reappeared. I'm a Mac user and need the bridging mode at home for my home automation system that only comes with some windows tools. Therefore I spend some time to figure out more details and was able to solve the problem.
    It turned out, that the AP needs to get an IP address by DHCP, otherwise the Windows machine never gets an IP address. I was able to see the DHCP discover broadcast from my virtual Windows PC as well as the DHCP offer from my home router. Even the packets from the DHCP relay agent (the AP with ip-helper) and the reply packet from the home router were shown with a DHCP debug on the AP and also with Wireshark on the LAN, but these broadcasts were not forwarded to wireless client. I've used Wireshark to capture packets on the WLAN adapter of my Macbook to verify that these packets were dropped on the AP and not on the Macbook with VMware Fusion. For some unknown reason the AP (acting as a bridge!) does not forward these broadcasts to the wireless client. 
    After playing around it turned out, that it WORKS if the AP itself is configured as a DHCP client and does not have a static address AND there is a DHCP entry for my virtual Windows PC like this:
    ip dhcp pool Macbook
     host 192.168.128.44 255.255.255.0
     client-identifier 0100.5056.1234.56
     dns-server 192.168.128.1
     default-router 192.168.128.1
     domain-name home.local
    It's a bit weird that the AP itself needs to be a DHCP client and I can't explain why, but this setup works for me. I like to keep the DHCP server on my home router, so I've only added this DHCP reservation on the AP. 

  • Is it possible to config H-REAP/REAP and CAPWAP in Autonomous mode with a WLC?

    I'm going to deploying all new AP as Remote-Edge AP and they will be shipped straight to site.  With a pool of WLCs deployed in central DC locations.  I would like to get local staff to deploy a basic CLI discovery script for the APs.  However, i thought LAPs don't have CLI???
    I'm thinking I must use a Lightweight AP with the WLC to use Remote-Edge AP functionality - However, I'm not sure... the configuration example at the bottom doesn't state whether it an Autonomous AP or a Lightweight one.  
    http://www.cisco.com/en/US/products/ps6087/products_tech_note09186a0080736123.shtml
    H-REAP Controller Discovery using CLI commands
    H REAPs will most commonly discover upstream controllers via DHCP option 43 or DNS resolution. Without either of these methods available, it may be desirable to provide detailed instructions to administrators at remote sites so that each H REAP may be configured with the IP address of the controllers to which they should connect. Optionally, H REAP IP addressing may be set manually as well (if DHCP is either not available or not desired).
    This example details how an H REAP's IP address, hostname, and controller IP address may be set through the console port of the access point.
    AP_CLI#capwap ap hostname ap1130ap1130#capwap ap ip address 10.10.10.51 255.255.255.0ap1130#capwap ap ip default-gateway 10.10.10.1ap1130#capwap ap controller ip address 172.17.2.172
    Could anyone help?
    Cheers
    Adrian.

    Hi Adrian,
    Further down in the doc you linked;
    H-REAP Controller Discovery using CLI commands
    H REAPs will most commonly discover upstream controllers via DHCP       option 43 or DNS resolution. Without either of these methods available, it may       be desirable to provide detailed instructions to administrators at remote sites       so that each H REAP may be configured with the IP address of the controllers to       which they should connect. Optionally, H REAP IP addressing may be set manually       as well (if DHCP is either not available or not desired).
    This example details how an H REAP's IP address, hostname, and       controller IP address may be set through the console port of the access       point.
    AP_CLI#capwap ap hostname ap1130
    ap1130#capwap ap ip address 10.10.10.51 255.255.255.0
    ap1130#capwap ap ip default-gateway 10.10.10.1
    ap1130#capwap ap controller ip address 172.17.2.172
    Note: Access points must run the LWAPP-enabled IOS® Recovery Image Cisco           IOS Software Release 12.3(11)JX1 or later, in order to support these CLI           commands out of the box. Access points with the SKU prefix of LAP (for example,           AIR-LAP-1131AG-A-K9), shipped on or after June 13, 2006 run Cisco IOS Software           Release 12.3(11)JX1 or later. These commands are available to any access point           that ships from the manufacturer running this code level, has the code upgraded           manually to this level, or is upgraded automatically by connecting to a           controller running version 6.0 or later.
    These configuration commands are only accepted when the access point is       in Standalone mode.
    Cheers!
    Rob

  • Setting a WLAN on 1841W in autonomous mode!

    Hi guys
    I have a setup where i am installing 1841W router which also has an 4-port ethernet module for wired users.
    There are different levels of complexities involved, as of now I will only keep it to 4 points:
    1. I need to have just one VLAN on the WLAN (VLAN 320)
    2. The users will be required to be authenticated via a NPS server across the WAN
    3. The wired users will have two VLANs, Data and Voice (VLAN 240 and 651)
    4. All the VLANs will need to go a DHCP servers for ip addresses for the clients.
    Based on the above, I have compiled a rough config, wanted to know if I am missing something:
    ***************************Router********************************
    hostname A
    no aaa new-model !(I have to configure this bit)
    service-module wlan-ap 0 bootimage autonomous
    controller Cellular 0/1
    interface Loopback0
    ip address 128.1.1.1 255.255.255.255
    interface Loopback1
    ip address 10.51.240.1 255.255.255.255
    interface Embedded-Service-Engine0/0
    no ip address
    shutdown
    interface GigabitEthernet0/0
    no ip address
    shutdown
    duplex auto
    speed auto
    interface wlan-ap0
    description Service module interface to manage the embedded AP
    ip address 1.1.1.1 255.255.255.255
    arp timeout 0
    no mop enabled
    no mop sysid
    interface Wlan-GigabitEthernet0/0
    description Internal switch interface connecting to the embedded AP
    no ip address
    interface GigabitEthernet0/0/0
    switchport access vlan 240
    switchport voice vlan 651
    no ip address
    interface GigabitEthernet0/0/1
    switchport access vlan 240
    switchport voice vlan 651
    no ip address
    interface GigabitEthernet0/0/2
    switchport access vlan 240
    switchport voice vlan 651
    no ip address
    interface GigabitEthernet0/0/3
    switchport access vlan 240
    switchport voice vlan 651
    no ip address
    ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 !(Assuming 3G service is working)
    **********AP CONFIG************
    hostname AP1
    enable secret 5 $1$nD9N$8fK4tS4Yb8k7rTYyosEU2/
    dot11 syslog
    dot11 ssid VCORP
       vlan 320
    username cisco privilege 15 secret 5 $1$Oc3J$IjBvJw47ZjflC2181on6k0
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid VCORP
    antenna gain 0
    station-role root
    interface Dot11Radio0.1
    encapsulation dot1Q 320 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    ssid VCORP
    antenna gain 0
    no dfs band block
    channel dfs
    station-role root
    interface Dot11Radio1.1
    encapsulation dot1Q 320 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
    no ip address
    no ip route-cache
    interface GigabitEthernet0.1
    encapsulation dot1Q 320 native
    no ip route-cache
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 10.51.246.1 255.255.255.0
    ip helper-address 10.32.0.155
    no ip route-cache
    bridge 1 route ip
    Any suggestions if I am missing anything, or you think anythiing is wrong? I am not sure whether ip is to be given on the BVI interface or on
    G0 or G0.1???
    Cheers,
    Mohit

    Universal Client Mode
    Universal client mode is a wireless radio station role that allows the radio to act as a wireless client to another access point or repeater. This feature is exclusive to the integrated radio running in the Cisco 870, 1800, 2800, and 3800 integrated service routers (ISRs).
    Universal client mode has the following features and limitations:
    •You can configure universal client mode on the main dot11radio interface only, subinterfaces are not supported.
    •Universal client can associate to access points with radio VLANs.
    •Layer-3 routing is supported over the radio interface. However, there is no support for layer 2 (L2) bridging. The user cannot configure a dot11radio interface with a bridge-group when in universal client mode.
    •Service Set Identifiers (SSIDs) are required to be configured on the dot11 interface operating as a universal client; association to an access point running in guest mode is not supported.
    •The universal client can associate to Cisco access points, third party access points, and repeaters. It cannot associate to Cisco root bridges or Cisco workgroup bridges.
    •Easy VPN does not support universal client mode using DHCP.

Maybe you are looking for