Link outage in Etherchannel causes interface down and failover Secondary Faild

Hi,
I have configured port-channel Firewall ASA5515-X and  stacking switch WS-3750X. Also firewall configured as failover mode. Problem is that my active firewall connected switch port show green and working but standby firewall connected switch port shows orange color. When i inpute show failover command on firewall, secondary is faild. Please assist. Here is the below show command.
mdbl-int-fw-01# sho port-channel 10
Ports: 2   Maxports = 16
Port-channels: 1 Max Port-channels = 48
Protocol: LACP/ active
Minimum Links: 1
Maximum Bundle: 8
Load balance: src-dst-ip
mdbl-int-fw-01# sho interface port-channel 10
Interface Port-channel10 "inside", is up, line protocol is up
  Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
        Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
        Input flow control is unsupported, output flow control is off
        Description: *** Connected to CORE-SW ***
        MAC address 4c00.821d.511f, MTU 1500
        IP address 10.98.8.97, subnet mask 255.255.255.248
  Traffic Statistics for "inside":
        56859 packets input, 3419130 bytes
        148709 packets output, 16063580 bytes
        56858 packets dropped
      1 minute input rate 0 pkts/sec,  46 bytes/sec
      1 minute output rate 2 pkts/sec,  216 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec,  46 bytes/sec
      5 minute output rate 2 pkts/sec,  216 bytes/sec
      5 minute drop rate, 0 pkts/sec
  Members in this channel:
      Active:   Gi0/1 Gi0/2
mdbl-int-fw-01# sho port
mdbl-int-fw-01# sho port-channel sum
mdbl-int-fw-01# sho port-channel summary
Flags:  D - down        P - bundled in port-channel
        I - stand-alone s - suspended
        H - Hot-standby (LACP only)
        U - in use      N - not in use, no aggregation/nameif
        M - not in use, no aggregation due to minimum links not met
        w - waiting to be aggregated
Number of channel-groups in use: 1
Group  Port-channel  Protocol    Ports
------+-------------+-----------+-----------------------------------------------
10     Po10(U)           LACP    Gi0/1(P)   Gi0/2(P)  
mdbl-int-fw-01#
mdbl-int-fw-01# sho port-channel ?      
  <1-48>    Channel group number
  brief     Brief information
  detail    Detail information
  port      Port information
  protocol  protocol enabled
  summary   One-line summary per channel-group
  |         Output modifiers
  <cr>
mdbl-int-fw-01# sho port-channel bri
mdbl-int-fw-01# sho port-channel brief
                Channel-group listing:
Group: 10
Ports: 2   Maxports = 16
Port-channels: 1 Max Port-channels = 48
Protocol: LACP/ active
Minimum Links: 1
Maximum Bundle: 8
Load balance: src-dst-ip
mdbl-int-fw-01# sho port-channel ?    
  <1-48>    Channel group number
  brief     Brief information
  detail    Detail information
  port      Port information
  protocol  protocol enabled
  summary   One-line summary per channel-group
  |         Output modifiers
  <cr>
mdbl-int-fw-01# sho port-channel pro
mdbl-int-fw-01# sho port-channel protocol
                Channel-group listing:
Group: 10
Protocol: LACP
mdbl-int-fw-01# sho port-channel ?       
  <1-48>    Channel group number
  brief     Brief information
  detail    Detail information
  port      Port information
  protocol  protocol enabled
  summary   One-line summary per channel-group
  |         Output modifiers
  <cr>
mdbl-int-fw-01# sho port-channel det
mdbl-int-fw-01# sho port-channel detail
                Channel-group listing:
Group: 10
Ports: 2   Maxports = 16
Port-channels: 1 Max Port-channels = 48
Protocol: LACP/ active
Minimum Links: 1
Maximum Bundle: 8
Load balance: src-dst-ip
                Ports in the group:
Port: Gi0/1
Port state    = bndl
Channel group =   10        Mode = LACP/ active
Port-channel  = Po10
Flags:  S - Device is sending Slow LACPDUs   F - Device is sending fast LACPDUs.
        A - Device is in active mode.        P - Device is in passive mode.
Local information:
                             LACP port     Admin     Oper    Port        Port
Port      Flags   State      Priority      Key       Key     Number      State
Gi0/1     SA      bndl       32768         0xa       0xa     0x2         0x3d 
Partner's information:
          Partner Partner    LACP Partner  Partner   Partner  Partner     Partner
Port      Flags   State      Port Priority Admin Key Oper Key Port Number Port State
Gi0/1     SA      bndl       32768         0x0       0xa      0x118       0x3d 
Port: Gi0/2  
Port state    = bndl
Channel group =   10        Mode = LACP/ active
Port-channel  = Po10
Flags:  S - Device is sending Slow LACPDUs   F - Device is sending fast LACPDUs.
        A - Device is in active mode.        P - Device is in passive mode.
Local information:
                             LACP port     Admin     Oper    Port        Port
Port      Flags   State      Priority      Key       Key     Number      State
Gi0/2     SA      bndl       32768         0xa       0xa     0x3         0x3d 
Partner's information:
          Partner Partner    LACP Partner  Partner   Partner  Partner     Partner
Port      Flags   State      Port Priority Admin Key Oper Key Port Number Port State
Gi0/2     SA      bndl       32768         0x0       0xa      0x119       0x3d 
mdbl-int-fw-01#
mdbl-int-fw-01#
mdbl-int-fw-01#
mdbl-int-fw-01#
mdbl-int-fw-01# sho port-channel ?     
  <1-48>    Channel group number
  brief     Brief information
  detail    Detail information
  port      Port information
  protocol  protocol enabled
  summary   One-line summary per channel-group
  |         Output modifiers
  <cr>
mdbl-int-fw-01# sho fail        
mdbl-int-fw-01# sho failover st
mdbl-int-fw-01# sho failover state
               State          Last Failure Reason      Date/Time
This host  -   Primary
               Active         None
Other host -   Secondary
               Failed         Ifc Failure              22:03:03 UTC Jan 8 2014
                              outside: No Link
                              dmz: No Link
                              mgt: No Link
                              inside: No Link
====Configuration State===
        Sync Done
====Communication State===
        Mac set
mdbl-int-fw-01#
mdbl-int-fw-01#
mdbl-int-fw-01#
mdbl-int-fw-01# sho failover     
Failover On
Failover unit Primary
Failover LAN Interface: failover GigabitEthernet0/3 (up)
Unit Poll frequency 200 milliseconds, holdtime 800 milliseconds
Interface Poll frequency 500 milliseconds, holdtime 5 seconds
Interface Policy 1
Monitored Interfaces 4 of 114 maximum
failover replication http
Version: Ours 8.6(1)2, Mate 8.6(1)2
Last Failover at: 02:16:48 UTC Jan 8 2014
        This host: Primary - Active
                Active time: 74479 (sec)
                slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)
                  Interface outside (118.179.139.4): No Link (Waiting)
                  Interface dmz (10.98.56.3): No Link (Waiting)
                  Interface mgt (10.10.11.1): Unknown (Waiting)
                  Interface inside (10.98.8.97): Normal (Waiting)
                slot 1: IPS5515 hw/sw rev (N/A/7.1(4)E4) status (Up/Up)
                  IPS, 7.1(4)E4, Up
        Other host: Secondary - Failed
                Active time: 0 (sec)
                slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)
                  Interface outside (118.179.139.6): No Link (Waiting)
                  Interface dmz (10.98.56.2): No Link (Waiting)
                  Interface mgt (0.0.0.0): No Link (Waiting)
                  Interface inside (10.98.8.98): No Link (Waiting)
                slot 1: IPS5515 hw/sw rev (N/A/7.1(4)E4) status (Up/Up)
                  IPS, 7.1(4)E4, Up
Stateful Failover Logical Update Statistics
        Link : failover GigabitEthernet0/3 (up)
        Stateful Obj    xmit       xerr       rcv        rerr     
        General         12665      0          9929       0        
        sys cmd         9929       0          9929       0        
        up time         0          0          0          0        
        RPC services    0          0          0          0        
        TCP conn        0          0          0          0        
        UDP conn        0          0          0          0        
        ARP tbl         2735       0          0          0        
        Xlate_Timeout   0          0          0          0        
        IPv6 ND tbl     0          0          0          0        
        VPN IKEv1 SA    0          0          0          0        
        VPN IKEv1 P2    0          0          0          0        
        VPN IKEv2 SA    0          0          0          0        
        VPN IKEv2 P2    0          0          0          0        
        VPN CTCP upd    0          0          0          0        
        VPN SDI upd     0          0          0          0        
        VPN DHCP upd    0          0          0          0        
        SIP Session     0          0          0          0        
        Route Session   0          0          0          0        
        User-Identity   1          0          0          0        
        Logical Update Queue Information
                        Cur     Max     Total
        Recv Q:         0       7       9930
        Xmit Q:         0       30      99581
mdbl-int-fw-01#
mdbl-int-fw-01#
mdbl-int-fw-01# sho failover state     
               State          Last Failure Reason      Date/Time
This host  -   Primary
               Active         None
Other host -   Secondary
               Failed         Ifc Failure              22:03:03 UTC Jan 8 2014
                              outside: No Link
                              dmz: No Link
                              mgt: No Link
                              inside: No Link
====Configuration State===
        Sync Done
====Communication State===
        Mac set
mdbl-int-fw-01# sho failover ?   
  descriptor  Show failover interface descriptors. Two numbers are shown for
              each interface. When exchanging information regarding a
              particular interface, this unit uses the first number in messages
              it sends to its peer. And it expects the second number in
              messages it receives from its peer. For trouble shooting, collect
              the show output from both units and verify that the numbers
              match.
  exec        Show failover command execution information
  history     Show failover switching history
  interface   Show failover command interface information
  state       Show failover internal state information
  statistics  Show failover command interface statistics information
  |           Output modifiers
  <cr>
mdbl-int-fw-01# sho failover inter
mdbl-int-fw-01# sho failover interface
        interface failover GigabitEthernet0/3
                System IP Address: 10.98.8.89 255.255.255.248
                My IP Address    : 10.98.8.89
                Other IP Address : 10.98.8.90
mdbl-int-fw-01# sho failover stati    
mdbl-int-fw-01# sho failover statistics
        tx:995725
        rx:980617
mdbl-int-fw-01# sho failover hi        
mdbl-int-fw-01# sho failover history
==========================================================================
From State                 To State                   Reason
==========================================================================
02:16:40 UTC Jan 8 2014
Not Detected               Negotiation                No Error
02:16:48 UTC Jan 8 2014
Negotiation                Just Active                No Active unit found
02:16:48 UTC Jan 8 2014
Just Active                Active Drain               No Active unit found
02:16:48 UTC Jan 8 2014
Active Drain               Active Applying Config     No Active unit found
02:16:48 UTC Jan 8 2014
Active Applying Config     Active Config Applied      No Active unit found
02:16:48 UTC Jan 8 2014
Active Config Applied      Active                     No Active unit found
==========================================================================
mdbl-int-fw-01# sho failover        
Failover On
Failover unit Primary
Failover LAN Interface: failover GigabitEthernet0/3 (up)
Unit Poll frequency 200 milliseconds, holdtime 800 milliseconds
Interface Poll frequency 500 milliseconds, holdtime 5 seconds
Interface Policy 1
Monitored Interfaces 4 of 114 maximum
failover replication http
Version: Ours 8.6(1)2, Mate 8.6(1)2
Last Failover at: 02:16:48 UTC Jan 8 2014
        This host: Primary - Active
                Active time: 74554 (sec)
                slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)
                  Interface outside (118.179.139.4): No Link (Waiting)
                  Interface dmz (10.98.56.3): No Link (Waiting)
                  Interface mgt (10.10.11.1): Unknown (Waiting)
                  Interface inside (10.98.8.97): Normal (Waiting)
                slot 1: IPS5515 hw/sw rev (N/A/7.1(4)E4) status (Up/Up)
                  IPS, 7.1(4)E4, Up
        Other host: Secondary - Failed
                Active time: 0 (sec)
                slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)
                  Interface outside (118.179.139.6): No Link (Waiting)
                  Interface dmz (10.98.56.2): No Link (Waiting)
                  Interface mgt (0.0.0.0): No Link (Waiting)
                  Interface inside (10.98.8.98): No Link (Waiting)
                slot 1: IPS5515 hw/sw rev (N/A/7.1(4)E4) status (Up/Up)
                  IPS, 7.1(4)E4, Up
Stateful Failover Logical Update Statistics
        Link : failover GigabitEthernet0/3 (up)
        Stateful Obj    xmit       xerr       rcv        rerr     
        General         12676      0          9938       0        
        sys cmd         9938       0          9938       0        
        up time         0          0          0          0        
        RPC services    0          0          0          0        
        TCP conn        0          0          0          0        
        UDP conn        0          0          0          0        
        ARP tbl         2737       0          0          0        
        Xlate_Timeout   0          0          0          0        
        IPv6 ND tbl     0          0          0          0        
        VPN IKEv1 SA    0          0          0          0        
        VPN IKEv1 P2    0          0          0          0        
        VPN IKEv2 SA    0          0          0          0        
        VPN IKEv2 P2    0          0          0          0        
        VPN CTCP upd    0          0          0          0        
        VPN SDI upd     0          0          0          0        
        VPN DHCP upd    0          0          0          0        
        SIP Session     0          0          0          0        
        Route Session   0          0          0          0        
        User-Identity   1          0          0          0        
        Logical Update Queue Information
                        Cur     Max     Total
        Recv Q:         0       7       9940
        Xmit Q:         0       30      99677

Hi Ganesan,
I am proposing a design like this. You can have the STP in pvst mode and have a different priority set for the core switch to make it core a as root bridge. There is nothing wrong with your design you have made you core switch which will be physically down to your firewall... but in real it comes on the top of your firewall as well... But spanning tree conf should be done properly to achieve this... I have proposed my design which is pretty simple but easy for troubleshoot....
You can have your firewalls connected to core switch on the down and can directly connected to router on outside... always core a -->py fw--rtra will be the primary path... if anything goes wrong then secondary line will come in to picture....
make sure that your hsrp will have high priority to ur core a vlan conf for the access switches.....
Please do rate for the helpful posts.
By
Karthik

Similar Messages

  • Adobe Reader 8.1 causing slow down and crashes

    Despite safely using 7.0 for years, when I updated to 8.1, my computer slowed to a snail's pace and froze frequently, more than hourly. I have definitely traced the problem to Adobe Reader 8.1 (8.1.2?)because the problems disappeared the several times I uninstalled it. I am now using 7.0 without any problems. Does any one have an idea what the problem is? Can I ever safely upgrade to Version 8?

    The link to the Reader forum is at the top of this forum.

  • SLM248p web interface down and time reset

    My SLM248P web interface keeps locking up (i.e. I get noting when I go to the IP address of the switch).  I need to power cycle the switch to get the web interface to work.  Also, whenever I reset the power, it goes back to Jan 1, 2000 (time).  The swithc alsow seems to loose connections every now and then.  And I keep getting a waring in the log that looks something like
    "%STP-W-PORTSTATUS: e26: STP status Forwarding"

    I have the newest firmware.  It has no impact on the situation.

  • VIF Bound Physcial Interface Down

    Hi Guys!
    We are trying to connect FI 6248 (UCSM 2.1.1a) to Brocade 6510 swtich(One FI to one of the two Brocade switches separately). The ports are configured as FC Uplink port and the FI's work in End-host mode. We created the service profile. After associating the SP to one of the blades the two errors occurs immediately:
    VIF <number> Bound Physical Interface Down
    VIF <number> Bound Physical Interface Down
    and this relates to the 2 vHBAs created in SP. Is this normal situation if OS isn't already installed on the host? We can't configure SAN zone from the brocade side because we don't see any WWPNs of the configured vHBAs in the SP. We see only FI's WWPNs(as I think). NPIV mode is enabled from the Brocade side. 
    Can someone explain what can cause this problem?

    Sergey,
    This is expected if there is no OS installed yet, see the possible reasons for the VIF down in this bug:
    https://tools.cisco.com/bugsearch/bug/CSCul99847
    Rate ALL helpful answers.
    -Kenny

  • My iPad isn't working properly. When I try to connect to the internet or follow a link it shuts down and returns to the main screen. Any clue as to what could be causing this? Not my internet connection, I checked that.

    My iPad isn't working. I cannot follow a link in an email or connect to a game. It goes to a black screen then back to the main screen. Any idea what could be causing this?

    Settings > General > Reset > Reset Network Settings
    Perform a "hard reset" on the device by pressing down and holding the home button and the sleep/wake button for up to 30secs. until you see a black screen with the Apple logo, then release.
    Then test to see if it solved the problem.

  • When Firefox freezes, how can I shut it down, and re-start it without it automatically going to the site which caused the problem in the first place ?

    I have Firefox set so that when I start up, I have it set so that it automatically goes to my home page. However when it freezes, which it does on a daily basis, and I have to shut it down and re-start, it automatically goes to the site which caused the problem in the first place.
    If I was a hacker, I would probably find it quite fun to design a virus to reintroduce bugs after they had been exterminated - except that Firefox seem to have got there first.

    Here's how:
    (1) In a new tab, type or paste '''about:config''' in the address bar and press Enter. Click the button promising to be careful.
    (2) In the search box above the list, type or paste '''sess''' and pause while the list is filtered
    (3) Double-click the '''browser.sessionstore.max_resumed_crashes''' preference and enter 0 (that's a zero) and click OK.
    When Firefox resumes after a crash, instead of resuming automatically, it will display a list of your previous windows and tabs and you can deselect problem pages.
    (This assumes it wasn't a private browsing session.)

  • Link down and Link Up Snmp trap C#

    Hi i've configure my cisco router to receive the SNMP traps if the link goes up or down. However i found out that when i plugged out the cable i'm not receiving any link down on the network management system. Until i plugged in again the link will then show up or down state. May i know whats the reason why i can't receive the link down when i plugged out my cable?

    If your router has only fa0/0 as active interface, then this would be the interface that the router would use to communicate with the network management system. However when you unplug that interface now the router has no interface that it can use to send the link down trap to the network management system.
    HTH
    Rick

  • Problems with RH 9Printed Documentation not displaying some popups, drop-downs, and links

    I generate a Word document for reviewers. PrintedDoc properties include: Retain hyperlinks; Include drop-down text; Include expanding text.
    Sometimes the Word 2010 document includes hyperlinks, sometimes it doesn't.
    Popups typically don't work in the Word document.
    Drop-down and expanding text appear intermittently in the Word document.
    Has anyone experienced this and have a solution?
    Thanks.
    Carol

    I have never known hyperlinks to fail except in two situations.
    The target topic is not in the printed document. Obviously it cannot link to something that is not there.
    The hyperlink is a popup.
    Not sure what you mean by popups not working in a printed document. If you mean the links to them break, then see above. Known issue.
    I'm not sure why you are having the dropdown and expanding text problem as I have not known that to be an issue either. Is it always the same dropdowns that fail? Have you compared a good dropdown and a bad dropdown?
    Take a look at Printed Documentation on my site.
    See www.grainge.org for RoboHelp and Authoring tips
    @petergrainge

  • Hello, I'm pretty sure my fan on my 2009 mac book pro has stopped running. Would this cause the computer to slow down and take for ever to boot up and show the color wheel every time I select an application ?

    Hello, I'm pretty sure my fan on my 2009 mac book pro has stopped running. Would this cause the computer to slow down and take for ever to boot up and show the color wheel every time I select an application ? how involved to replace fan ? cost ?
    thanks

    Not directly, but if the CPU overheats because of incompatible software, that would cause slowdowns. Do not allow the computer to run if the fan is not working unless you wish to fry your motherboard. Please make a Genius Appointment and take it in for service.

  • Downloaded songs frome itunes and internet went down and they will not play and it also caused other songs not to but most will what do i need to do wiyhout erasing everything

    downloaded songs from itunes and the internet went down and they will not play and also caused other songs already downloaded not to play what can i do

    You can try a couple of different things. First - restart the iPod and see if the songs will play.
    Restart the iPod by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
    If that doesn't help - delete the songs and then download them again. You can download purchased music again at no charge as long as you use the same Apple ID that you bought them with originally and as long as you live in one of these countries.
    Previously purchased music is only available through iTunes in the Cloud in  Argentina, Australia, Belgium, Bolivia, Brazil, Canada, Chile, Colombia, Costa Rica, Cyprus, Czech Republic, Dominican Republic, Ecuador, El Salvador, France, Germany, Guatemala, Honduras, Ireland, Luxembourg, Malta, Mexico, New Zealand, Nicaragua, Panama, Paraguay, Peru, Slovakia, Spain, Switzerland, the United Kingdom, United States, and Venezuela.
    If you are running iOS 5 on the iPod - You can delete songs by swiping across the song in list view to bring up a red delete button. Tap the button to delete the songs. Download the songs again in the purchased tab in iTunes.
    Downloading Past Purchases

  • Unidentified traps and interface down alerts LMS 4.2

    Hi all,
    Sometimes we have unidentified traps in our log, we don't know where they come from.
    In high severity faults we see an active alert with device name “Unidentified” event name unresponsive but with a certain ip address.
    What are these alerts about? Can I filter them?
    A second issue I have is that I get interface down alerts. But when we log on to the device, there is no interface down at all. We can also ping the device from the lms server at that time. I have been told that the admin state and operational state has to be up.
    Thanks,
    Best Regards,
    Joris

    Hi Joris,
    Generic trap support is a new feature introduced in LMS 4.2 release. look at the below
    document also.
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/lms_monitor/TrapFwd.html#wpxref13049
    LMS 4.2 release onwards DFM will display any unprocessed traps comming from device in
    fault monitor screen as unidentified trap under Inform alarm.
    For the other issue , it could be a DFM database issue , try to REDISCOVER those devices in
    DFM and see how it works
    Thanks
    Afroz

  • Scrolling down and using links to anchors aren't in sync

    This video shows a site I'm creating.  I start in design mode.  Then I click to preview.  As I Scroll down and the page stops too soon.  When I use the links to anchors it goes all the way down.  How can I get the page to work the same when scrolling as it does when using links to anchors?
    I noticed that when I use the links to anchors the bottom portion of the menu gets pushed down a couple of inches.  That seems to be the problem.  Why does using anchors do this and how can I fix it?

    You want to precompose your stills and the track mattes together.  The composition should look like the stills with a rounded rectangle border.  Then animate the composition.

  • Interface dot11radio1 is reset down and does not works.

    I configured ssid and is a nonroot equipement and whwn I do sh ip inter brief the status interface dot11radio1 is reset and down and does not assosciate with the root AP
    This is the configuration:
    ip ssh version 1
    dot11 ssid fbpinto
    authentication open
    authentication shared
    authentication key-management wpa
    wpa-psk ascii 7 051C160E315F450F1B151E1C1F03
    dot11 network-map
    power inline negotiation prestandard source
    username Cisco password cisco
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    shutdown
    station-role root bridge
    infrastructure-client
    bridge-group 1
    bridge-group 1 spanning-disabled
    no sh
    interface Dot11Radio1
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm tkip
    ssid fbpinto
    antenna gain 9
    power client local
    station-role non-root bridge
    infrastructure-client
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    bridge-group 1 spanning-disabled
    no sh
    interface BVI1
    ip address 172.27.119.10 255.255.255.128
    no ip route-cache
    no sh
    ip default-gateway 172.27.119.1

    Thanks very much!
    Then untilk the noonroot is not associate the interface radio remanis in  restet status protol down ¿is it?
    My problem is that this Brigge  working fine for a year ago but  one day fails and I replace the bridge  but the interface radio remain in status reset  too¿can be that the extenal antenna is broken? and therfore no signal received by the interface and can not associate with root for it?
    I try to put boths brigge close and test if interface radio is up and works fine .If works like this I think that is a problem with the extrenal anntena ( dipolo)
    regards

  • When downloading CS 5.5 from the direct link it eventually slows down and stops.  How am I supposed to download the file?

    I am trying to download CS 5.5 on to my new laptop since my old one died.  I am using the direct link found Download CS5.5 products.  It starts off fine but it slows down and eventually stops.  How am I supposed to download the entire file?  I am using Chrome on Windows 8.1 if it makes any difference.

    Adding to What Anand has mentioned, please make sure that any online active Defence system should be turned off ( For eg, Kaspersky, Norton or AVG ). Also, if you are behind a corporate network, please try a different network and check again.

  • Interface Controller and Link to URL

    Hi Experts,
    Could some give me the step by step process(PDF's suggested) for the Interface controller and Link to URL.
    Regards.

    hi,
    The application of downloading data from table to excel sheet
    will give a very good idea and the solution to ur problm
    Exporting Context Data into Excel Using the Web Dynpro
    Binary Cache
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/edc2f3c2-0401-0010-8898-acd5b6a94353
    Regards
    Nikhil Tapkir

Maybe you are looking for

  • Why whenever I turn on an external HD, iPhoto starts up?

    I have an MB Pro, 2.33, with a number of FW and SATA drives. I'm wondering why suddenly when I turn on an external HD, iPhoto starts up? thanks, elmer

  • Ajax Dynamic Conntent -- pull report from different page

    Hi All, I am reposting my question, the previous thread was hacked by Fifi :-) . I am trying to implement Denes's solution in this Pulling Dynamic Conntent . Somehow I am getting java script error "unknown runtime error". on page load itself. It is g

  • Colorista II not reseting parameters when double clicking in PP CS6

    I'm using Colorista II in Premiere Pro CS6 for the first time. Everything seems to operating properly except for the reset function within the tools - as opposed to the global reset, which does work. From the tutorial, I understand that double clicki

  • How do i "delete right" on my ipad 2?

    Is there a way to delete right on my ipad 2. If not on the ipad itself, is there a way to do it if i attach my Logitech case for Ipad 2? Clicking "control D" on the Logitech keyboard doesnt work and there are no function or command keys on the glass

  • Auto Create Table problem in Jdev903

    Hi, I am writing EJB application and used CMR. To develop this application I am using JDeveloper(Oracle 9i-OC4J).When I run this application, it metically creates CMR tables. But I don't want to that JDeveloper should create auto table, for that I ha