Lircd, irrecord shows input but irw doesn't

Hi,
I have IR receiver with rtl2832u DVB-T SDR device. I managed to create configuration file for my pilot (only one button for testing):
sudo irrecord --device=/dev/lirc0 MyRtlRemote.conf
...CUT...
Hold down an arbitrary button.
Found gap length: 409981
Now enter the names for the buttons.
Please enter the name for the next button (press <ENTER> to finish recording)
KEY_CHANNELUP
Now hold down button "KEY_CHANNELUP".
Please enter the name for the next button (press <ENTER> to finish recording)
Successfully written config file MyRtlRemote.conf.
This file was moved to /etc/lirc/lircd.conf.d directory.
Then I started lircd with command:
sudo lircd -n -d /dev/lirc0
There is no output in irw when I press one configured button on pilot.
Any ideas, why my pilot doesn't work?
I've found two similar topics, but these solutions don't work for me:
https://bbs.archlinux.org/viewtopic.php?id=121651
https://bbs.archlinux.org/viewtopic.php?id=116515&p=1
My ir-keytable output:
Found /sys/class/rc/rc0/ (/dev/input/event22) with:
Driver dvb_usb_rtl28xxu, table rc-empty
Supported protocols: NEC RC-5 RC-6 JVC SONY SANYO LIRC RC-5-SZ SHARP XMP other
Enabled protocols: LIRC
Name: Realtek RTL2832U reference desig
bus: 3, vendor/product: 0bda:2832, version: 0x0100
Repeat delay = 500 ms, repeat period = 125 ms
Last edited by Linkas (2015-02-23 19:42:52)

Happens with me too!!!!! please help us!!!!

Similar Messages

My Blu-Ray player has a USB input but it doesn't have an HDMI input. Can I connect my Apple TV to the Blu-Ray using an HDMI/ USB adapter? It would allow me to run the audio through my stereo. Thanks to all for your help.

My Blu-Ray player has a USB input but it doesn't have an HDMI input. Can I connect my Apple TV to the Blu-Ray using an HDMI/ USB adapter? It would allow me to run the audio through my stereo. Thanks to all for your help.

Can I connect my Apple TV to the Blu-Ray using an HDMI/ USB adapter?
If you can find such a thing. I really doubt that exists since USB is a data connector not a video connector.
would allow me to run the audio through my stereo.
That would depend on this adapter.

I recently synced my iphone4 on my iMac, but now I can't access my camera from the lock screen? It shows up but it doesn't open the camera? Does anyone know how to fix this? Thanks!

I recently synced my iphone4 on my iMac, but now I can't access my camera from the lock screen? It shows up but it doesn't open the camera? Does anyone know how to fix this? Thanks!

Can't believe it was that easy... I'm so dumb! Thanks for your help, I was getting so aggravated! I owe you... Thanks again!

I have a cooliris wall embedded in a website I built. IE shows it but Foxfire doesn't. I've looked for an add-on but the cooliris one goes to its own wall. I updated to ff4 but no difference. Is there a plug in I need?

I have a cooliris wall embedded in a website I built. IE shows it but Foxfire doesn't. I've looked for an add-on but the cooliris one goes to its own wall. I updated to ff4 but no difference.

I want all my devices to be on a password related internet but the double nat on my TC makes weird things happen and slow. I try bridge mode but the internet doesn't work.
You building supplied internet is a cheap service that is without proper routable addresses..
Therefore to use more than one IP you MUST have double NAT.. sorry there is no choice..
Slow that is because you are sharing internet with every other person in the building.. get your own broadband service.
Bridge will not work.. it cannot work because the building only has private IP addressing. And they only give you a single address.
You can put a password on the wireless.. go to the airport utility and put in a password.
Other than that I don't understand what password you expect.
Can I get an explanation of what bridge mode is?
No NAT.. means the TC becomes a dumb Wireless AP and switch.. works fine with a cable modem router.. or any broadband router but useless with your building system.
Can I get suggestions on what I should do to use the TC as a wireless device to spread the same wireless device my apartment is broadcasting?
Double NAT, and set your own wireless names. There is no alternative.. sorry.

OS X Mavericks does not download, infact shows downloaded but it doesn't appear anywhere in Launchpad and neither can I download it again

I am having trouble downloading the OS X Mavericks. In my initial attempt to download the update from the App Store, it started downloading but stalled. It wasn't paused, but just stalled. I restarted the Mac and tried to install it again. The next time the download commenced but stalled after reaching a certain point (it appears to have tried to restart from where it left off earlier), but the download doesn't continue. Says "Mac OS X Mavericks failed to download". Now on deleting the icon from Launchpad, when I try to install it again from the App Store, it shows downloaded. How do I restart the download process and install Mac OS X Mavericks? I am currently on OS X Lion 10.8.5.

Yes, I do have an external drive, which I now disconnected and restarted the Mac to try installing. Didn't work.
I then kept it disconnected and restarted in Safe Mode, which again when trying to download showed "Downloaded". So didn't work.
Then tried one final time by plugging the external drive back in, and starting in normal mode and it appeared to have started downloading once again.
Unfortunately, it didn't give up so easily and the download is now stuck at 996MB.I think it's really testing my patience now. I tried looking up the communities for a similar issue and see that others have had their download stop at 996MB, but it seems to be an ISP/Router related issue, and I don't have alternatives for either.
Have written to the local Apple retailer for support, fingers crossed.

How can i do to watch a movie that already showed download but it doesn't work

hello
i have a problem, i download last night a movie from itune, then it showed it would need around 3 hours to download, this morning aparently is done, but i can't open it to watch??

Si vous avez utilisé la commande Save As Template depuis Pages, il y a forcément un dossier
iWork > Pages
contenant Templates > My Templates
comme il y a un dossier
iWork > Numbers
contenant Templates > My Templates
Depuis le Finder, tapez cmd + f
puis configurez la recherche comme sur cette recopie d'écran.
puis lancez la recherche.
Ainsi, vous allez trouver vos modèles personnalisés dans leur dossier.
Chez moi, il y en a une kyrielle en dehors des dossiers standards parce que je renomme wxcvb.template quasiment tous mes documents Pages et wxcvb.nmbtemplate à peu près tous mes documents Numbers.
Ainsi, quand je travaille sur un document, je ne suis pas ralenti par Autosave.
Désolé mais je ne répondrai plus avant demain.
Pour moi il est temps de dormir.
Yvan KOENIG (VALLAURIS, France) mercredi 23 janvier 2011 22:39:28
iMac 21”5, i7, 2.8 GHz, 4 Gbytes, 1 Tbytes, mac OS X 10.6.8 and 10.7.2
My iDisk is : <http://public.me.com/koenigyvan>
Please : Search for questions similar to your own before submitting them to the community

Audio line-in shows input, but no audio?

I got a MyFi xm2Go player that I plugged in to my MDD's audio line-in jack with a patch cable (3.5mm to 3.5mm). I can't seem to get it to play through my MDD.
Checked under the Sound preferences. Line In selected for input, and the levels fluctuate like its got the signal. Verified Line Out was still my one option. Played with all the volume sliders. Even plugged headphones into the jack on the base just to make sure it worked, and it does.
I can't get the audio to play through.
What am I missing?
Thanks in advance...

I'm going to change this to "answered" because thanks to this conversation I have found a solution.
Versiontracker has a freeware program called LineIn that bridges this gap. It will let you select your audio in and out and with a click of a button labeled "Pass Thru" it plays any audio input through your audio output.
http://www.versiontracker.com/dyn/moreinfo/macosx/18987
Just like OS X should.
This might be beating a dead horse, but one of the most disappointing things about the migration to OS X was these missing bits of functionality that somehow got lost in translation. I have heard the defense that since OS X is a brand new operating system from the kernel on up it's not a question of having taken something away.
Rubbish.
At the risk of sounding obnoxious, from the end user's standpoint if I go from 9 to 10 I shouldn't be losing any functionality of 9 by going to 10. If 9 had pass through, it's Apple's obligation to build that functionality into 10. If 10 is brand new from the ground up, find a way to recreate that new functionality.
It's clearly possible. I found a third-party non-Apple developer that did it.
The reason I'm ranting is that I shouldn't have had to hunt for this answer or a third-party solution in the first place. This is an obvious need that Apple really should have handled for me. The "pass-through" button should have either been there, or not been necessary because line-in audio would automatically be passed through to the line-out selected.
/rant.
Thanks for the help, everyone. I really do mean that. I am now grooving to satellite radio through my Mac thanks to you folks.

Fax test shows passed but fax doesn't work comm error

new machine . fax test passed but when fax is trying to be sent comes back as comm error. help

Hi @farmerj15 ,
I see by your post that when you try to send a fax you are getting a comm error, the fax test all passed. I will do my best to help you.
Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation.
I have provided a document to go through the steps to see if that will resolve the issue.
Cannot Send or Receive Faxes.
Sorry for all the questions, but it will help to resolve this issue quicker if you are still having issues.
Please let me know the following:
Can you receive a fax?
What kind of line do you have? (Analogue, DSL, Cable Modem)
Where is the fax cable connected to? (modem, wall jack)
Are you using a filter?
Are you using the 2 wire fax cable?
Do you have distinctive ring set up on the line?
Is there any voice mail set up?
Do you have a answering machine? (Where is it connected to)
Is there a phone also connected the printer?
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

IPod touch 2nd gen hooked up to computer but iTunes doesn't recognize it

My iPod touch 2g 8GB has always worked fine and synched with the computer, but now the computer doesn't recognze. It is hooked up to the cable and in the USB port. The iPod itself shows that it is charging, so it knows it's in the computer. iTunes should show devices but it doesn't. What should I do? I can't synch new songs or apps. I tried reseting everything and hooking up my ipod to a different port but still the computer doesn't recognize it.

Mac OS X v10.6 or later: iOS device not recognized in iTunes after restart

Chinese Pinyin input candidate window doesn't Show up

Hi,
Sometimes when I switch to Pinyin (Simplified Chinese) input mode, when I start typing, the candidate window (that lists possible matches) doesn't show up, but if I type space it still produces the first candidate. This problem is not consistent, sometimes it occurs, other times it's fine.
This happens everywhere, in browsers, text editors, etc.
Any idea what the problem might be?
Thanks!
Bob

I don't know what causes the problem. But I know a solution that you may try next time the candidate window disappears.
Click the language symbol in the menu bar, and open "Preferences". Then choose the "Candidate Window" tab, and change the window direction to "Vertical". Close the Preferences window, and try to type something in any text field/box. You'll see the candidate window comes back.

I purchased a movie from itunes on my ipad but it doesn't show up in my library. It shows up in my history of purchases when I open that page but it is not noted in the list of purchases with all my other purchases. Any idea why?

I purchased a movie from itunes on my regular ipad but it doesn't show up in my library. I am able to view it via my movies icon on the Ipad I used when purchasing it but it does not show up in my purchases listing to download to my ipad mini. Also if I access my itunes account it does not show up in the history of purchases listing like all my other purchases but it does show up when i open that page at the very top; separate form the list. I've tried everything to get it to show up so I can download/view it on my ipad mini.

Hi adtsalmon,
You can only watch the movie on the device you rented it on. Here's a snippet from the Apple Support site (italics mine):
If you download a rented movie on your computer: You can transfer it to a device such as your Apple TV (1st generation), iPhone, iPad, or iPod if it’s a standard-definition film (movies in HD can only be watched on your computer, iPad, iPhone 4 or later, iPod touch (4th generation or later), or Apple TV). Once you move the movie from your computer to a device, the movie will disappear from your computer's iTunes library. You can move the movie between devices as many times as you wish during the rental period, but the movie can only exist on one device at a time.
If you download a rented movie on your iPhone 4 or later, iPad, iPod touch (4th generation or later), or Apple TV: It is not transferable to any other device or computer.
Here's the link to the Movie Rentals FAQs site FYI:
http://support.apple.com/kb/HT1657
Hope this helps!
Cheers,
GB

When trying to update apps it asks for account password but it doesn't show my account. Help!

When trying to update apps it asks for account password but it doesn't show my account ID, it shows my dad's. How can I fix this so I can sign in?

It sounds like the apps were purchased using your dads account, so they will have to be updated using that account.

When I go to plug in my iPhone 5 to my PC it will charge my phone but it doesn't show up that it's connected to my computer or in iTunes. I have tried just about everything that I can find on the internet but nothing is working. Any other suggestions?

When I go to plug in my iPhone 5 to my PC it will charge my phone but it doesn't show up that it's connected to my computer or in iTunes. I have tried just about everything that I can find in the support discussions but nothing has worked. Any other suggestions?

If you have carefully follow ALL of the steps in that article, you are using a USB port directly on your computer and not a USB hub (don't use a front port on a tower or desktop either, as they are an internal hub) and you installed iTunes correctly using an Administrator ID and you have tried disabling your antivirus and firewall then there is no hope of it ever working. Look at the tip again, and go through it carefully, not skipping any steps.
Note, BTW, that an iPhone will not show up on a computer, only in iTunes. If there are photos in the Camera Roll then it will appear in Windows as a digital camera only.

I downloaded pages from the app store and I can use it on my Mac login but it doesn't show up when my wife logs in to her account? Were using the same computer, just different logins.

I downloaded pages from the app store and I can use it on my Mac login but it doesn't show up when my wife logs in to her account? Were using the same computer, just different logins.

No. You need to buy it for your Apple ID and for the other. You will have problems with updates

I'm using iphoto9.1.3 but now it doesn't seem to work, whenever I try to open it, it just shows loading, but never loads. Can anybody help me with this ?

I'm using iphoto9.1.3 but now it doesn't seem to work, whenever I try to open it, it just shows loading, but never loads. Can anybody help me with this ?

Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Rebuild iPhoto Library Database from automatic backup.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. .
Regards
TD

Lircd, irrecord shows input but irw doesn't

Similar Messages

Maybe you are looking for