Logic 9 ultrabeat has low volume!!

hey!
Whenever I load ultrabeat, I hear a few loud hits and then the volume goes down automatically I can see the signal coming but the volume is really low can someone please help me out?
I am using logic 9.1.8 on OSX 10.9.4
cheers!

Thanks again,
I have frozen all tracks except a 3 live tracks that use some compression and space designer etc. Nothing fancy.
I Logic Pro takes up 584 MB memory, and I have 3.82 MB free memory.
Funny enough, a second song started behaving erratically. There is a voice track audible that I have deleted before. The corresponding channel strip works with input, but can't be seen anywhere. It's not visible. Is there a gremlin in my Macbook?

Similar Messages

The left speaker has lower volume than the right speaker of my pavilion g4-1202ax..

please help me with this problem..
the left speaker has low volume..
but the balance is equal..
what should i do??
is any one there wants to help me??

I tried tightning the cables to the computer too.

Audio playback is clipped and has low volume

Hi, I'm hoping that someone can help me debug my audio problems.
The problem is that audio playback is clipped and has low volume.
The details of my setup are as follows:
- An onboard soundcard (ASUS M4A78LT-M-LE motherboard), identified as Intel HDA in dmesg:
description: Audio device
product: SBx00 Azalia (Intel HDA)
vendor: ATI Technologies Inc
physical id: 14.2
bus info: pci@0000:00:14.2
version: 00
width: 64 bits
clock: 33MHz
capabilities: pm bus_master cap_list
configuration: driver=snd_hda_intel latency=64
resources: irq:16 memory:f9ff4000-f9ff7fff
- ALSA (snd_hda_intel driver) and Pulseaudio
My ALSA mixer settings (which were used in the recording shown in this post) are at pastebin.
The mixer settings were chosen so that all "dB gain" is 0.00 for all columns in alsamixer.
Recording an MP3 (played at full volume) from the Stereo Mixer source in audacity I gives output which looks clipped and has low volume (link).
This occurs with any MP3 and any other sound source (Youtube in Chromium, etc.)
The problem does not occur when I boot into Windows XP, so it doesn't seem to be a hardware problem.
I'm also attaching a screenshot of my alsamixer playback screen for the soundcard (link)
Thanks for any assistance!

Hi,
I have the same problem since December 2011 with a similar Mainboard (Asus M4A78T-E).
Did you resolve your problem?
Thanks

Hi. I Have a Pavilion dv9000 which has always had very low volume - really needs to be increased?

Hi. I Have a Pavilion dv9000 with Vista Ultimate 64. It has always had very low volume and I find I generally have to have the volume up into the 70's 80's as well as the onscreen media player slider almost full - which then gets all distorted - and then have to turn it down again when not using the player as the computer error beeps come screaming out., Ive checked the settings on speakers to make sure all are the same & balanced and also have updated any codecs as needed. Is there a sound lever setting elsewhere?
cheers

Thanks for the reply and peeling my post off Mike, sorry I didn't start my own initially.
Well @ 1333Mhz I was using the rated timings 9-9-9-24 (as per Corsair) but it wasn't very stable as I said.
I have since changed the FSB/RAM ratio to get 1066Mhz and it seemed much happier. (@1.5v) It would be nice to run the RAM at it's rated setting but my OC skills aren't that extensive. I imagine it would need alot of tweeking? Or could I have just relaxed the timings a bit?
Would removing the Switch Cards make any difference?
Thanks in advance.

My new iPod touch (4th gen) has a significantly lower volume than my old one. I have maxed all the volumes and turned off the volume limit to no help. Can anyone help?

My new ipod touch 4th gen has a much lower volume than my old one, i have maxed the volumes out and got rid of all volume limits which has nor helped. Can anyone help?

Are you using the same headphones?
Did you officially purchase the in an EU country? They require a lower max volume than the USA and other countries.

HP Pavilion g6-1d98dx has very low volume.

Hi there,
I have an
HP Pavilion g6-1d98dx with W7 Ultimate that suddenly has very low volume. I have tried rolling back the drivers, uninstalling them and the device itself.
I also tried that loudness equalization option, but it only makes it worse. It used to sound very good, but now it's horrible. Now I have to wear a headset just to listen to music! Any help would be greatly appreciated. Thanks!
This question was solved.
View Solution.

Hi @Kindakool
I understand that you are having trouble with the sound from your built in speakers. I am happy to help you with this.
You can start with the following page, even though you are getting some sound.
No Sound from the Speakers (Windows 7)
Or you can check the connections on your internal speakers for that you will need:
HP Pavilion G6 Notebook PC - Maintenance and Service Guide
From Microsoft's support website:
Automatically diagnose and fix Windows audio playback problems
If those do not work it is possible that there is a physical problem with the speakers themselves. At that point I would call in to our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

MacBook Pro 2009 - Window 7 - Low Volume Output

I am experiencing low volume output on the internal speakers and slightly better volume on headphone output under BootCamp with Windows 7 x64 Ultimate. And of course the red light emitting diode is one constantly in the audio output jack.
I have seen fixes for the Windows XP folks over time and on my older MacBook (2006) with Vista x64, I found a fix. I have seen some thoughts on installing RealTek HD Audio drivers and that DID NOT work for Windows 7 x64 on my MacBook Pro 2009. I also tried reinstalling the CirrusAudio x64 from the BootCamp 3 drivers on my Snow Leopard DVD.
So I am left wondering if a driver update is forthcoming or if there is a fix that has been discovered and not reported online yet?

I'm going to leave this message for reference to other users...
As of October 22 2009 there is no known fix for the broken Cirrus Logic driver that comes with Bootcamp 3.0 under any 64bit Windows OS (including Windows 7 and Vista).
Apple seriously ***** for not doing anything about this for MONTHS and has lost a customer forever. I was going to get a 17in to complement my 13in MacBook Pro but this kind of driver issues is just plain unacceptable, and goes to show how you can't rely on a company like Apple for mission critical systems, period.
If they want to make ANY inroad in the corporate world the better get their stuff together and start delivering, the famous "excellent customer experience" for me is nowhere to be found. Lacking that, mac computers are only pretty although non-functional machines.
Sorry for the rant... I hope somebody from apple listens, but I doubt it.

Tab 7 low volume

Is it possible to fix the low volume problem on this tablet. Thanks.

I'm going to leave this message for reference to other users...
As of October 22 2009 there is no known fix for the broken Cirrus Logic driver that comes with Bootcamp 3.0 under any 64bit Windows OS (including Windows 7 and Vista).
Apple seriously ***** for not doing anything about this for MONTHS and has lost a customer forever. I was going to get a 17in to complement my 13in MacBook Pro but this kind of driver issues is just plain unacceptable, and goes to show how you can't rely on a company like Apple for mission critical systems, period.
If they want to make ANY inroad in the corporate world the better get their stuff together and start delivering, the famous "excellent customer experience" for me is nowhere to be found. Lacking that, mac computers are only pretty although non-functional machines.
Sorry for the rant... I hope somebody from apple listens, but I doubt it.

Guitar audio drop-out at lower volumes

I have tried out mainstage on a friends macbook pro, to check if it will be worth an investment into Logic over Garageband, mainly as an effects emulator for my guitar so I don't need to worry about amps in my small flat.   I connected through an Edirol UA-5 USB audio interface and while there were some issues with this interface anyway due to the fact I could only use input-1 rather than the Hi-Z Input-2 that I should use, I wanted to check some audio problems I had and see how to fix them.
Basically, at full volume on my guitar it seems to work fine, but as soon as I turn the guitar volume knob down there is literally no sustain anymore, I can hear a brief note and then it just cuts out, no gradual loss just stops.   If I only plug the interface in without mainstage then the monitor channel gives me the full volume control I expect and I tried my guitar on a proper external amp and it seemes to be fine so i've eliminated my guitar as the problem.
Anyone experienced this or have any suggestions to try to get it to work.
Also, if I use garage band I don't hear the output fromt he amp/effects simulators, only raw guitar and I only hear the final version if I record it and then play it back. Is there a way to get Garage band to act as a amp/fx simulator in a live mode like mainstage does or is the fact mainstage is playing back through the interface what might be causing the problems in some feedback loop??   Beginning to think an iRig would have been a better option......

CCTM wrote:
Djbungo wrote:
Basically, at full volume on my guitar it seems to work fine, but as soon as I turn the guitar volume knob down there is literally no sustain anymore, I can hear a brief note and then it just cuts out, no gradual loss just stops.
Hi
Sounds like you may have a Noise Gate in there somewhere?
CCT
yeah I thought of that but couldn't see anything, and think my knowledge of what a noise gate would do is slightly rusty since I assumed that at louder volumes it would clip and at lower volumes it would be fine....i'll have a play next time I am over my friends and see if I can spot anything.
Thanks for the quick reply.
MKS

Seemingly low volume for X-Fi Xtrememu

Today, the second time I booted up my computer I began to receive an interesting problem. My audio worked to some extent, but the volume was exceedingly low. I had to put my ear right next to the speakers to hear anything. I pulled out my headphones and plugged them in -- Same result, low volume. When I disabled the X-Fi and enabled my onboard audio, the volume was crystal clear and worked perfectly fine. I didn't change any software, drivers, hardware, or anything of that sort within the two reboots either.
I checked the obvious and made sure my volume was high in the X-Fi configuration panel, the windows panel, and my media players. Everything was maxed out. When I turned up my volume to the maximum on my speakers I could hear things better, but it was horribly distorted and sounded as if they were being over dri'ven. Normally I never have to increase the volume on the speakers much to hear anything, their usually on about 20-30% and I hear them perfectly fine.
I posted about this before on another site and It was recommended I try installing the latest drivers. So I decided to do an uninstall of the X-Fi drivers for good measure and, after rebooting, I installed the drivers and rebooted once more as it prompted me. The same exact result as before: sound that seems to have very low volume. After this, they recommended I try a different PCI slot as it may be damaged. I tried the other PCI slot and I had the same exact results as before. I did not want to install the card into the slot right next to my video card because it looked like the fan would be right up against the PCB of the X-Fi and that it might impede air flow and cause both cards to overheat.
Does anyone know what might be the problem? I'm using the latest drivers I saw (September 9th I believe) and the X-Fi has worked great for the past week and a half. I really don't want to have to own a $00 paperweight and revert to onboard audio.
Edit: If it helps any, I'm running on the following:
Asus A8N32 SLI Deluxe
AMD Opteron 70
X-Fi Xtrememusic
GeForce 7900 GT
If you need any other info, i'll post it.Message Edited by Sagekilla on 0-22-2006 2:9 PM

Bump.. Does anyone know how to fix this problem? I've made a list of all the fixes I've attempted
- Checked the volume in Creative's console, the Windows volume control in my tray bar, and in the Control Panel under "Audio and Sound devices"
- Made sure default device was the X-Fi
- Made sure the speakers was plugged in the right spot
- Made sure the speakers weren't faulty (I tested with a pair of head phones and on my iPod)
- Made sure I had the latest drivers
- Did the diagnostic, didn't help
- Did a system restore that made things worse
- Switched the PCI slot the sound card was in
- Tried onboard audio and found the audio there worked fine (I don't want onboard audio and a $00 paper weight though)
- Made sure onboard audio was uninstalled and disabled
- Posted on the creative labs forums and got no replies
- Safe Mode doesn't even recognize the Sound card
I'm pretty sure this isn't something stupid like "Is the volume turned up?"

Low volume warning

My son is currently having a problem connecting to itunes. When he brings up itunes he gets a low volume warning popup stating that itunes volume has been turned down low, howereve he cannot click past this warning box nor x out of it. He has not been able to use his ipod for the past two months and we aregetting very frustrated. i have tried to uninstall itunes and quick player and then reinstall but nothing has helped. Other than this new issue he has been using it successfully for two years. Please someone help!!!!!!

Why can't he dismiss the dialog box? Can he see the button on screen? Is it a screen resolution issue?

No sound vs low volume

I recently experienced the loss of all sound on my phone. It began after I unplugged the ear phones. I could not hear it ring and I could not hear anyone on the line although they could hear me. It was basically dead for about 4 hours or until I plugged the ear phones back in causing something to reset or whatever. It works fine now and Apple asked that I call when it occurs again so that we can try and trouble shoot and narrow the problem. I may have a defective phone.
I do not think this has any correlation with the "low volume" problem that everyone is talking about. I will agree with another writer that the volume is low until you activate the speaker but I have been using the speaker/hands free since the first day so perhaps that is why I have never experienced low volume. I think if the speaker is activated everyone will experience normal sound volume.
Dell Windows Vista
Dell Windows Vista

Faddy wrote:
I installed the Audigy 2 ZS last night. Updated everything, all of the drivers. I plug in my speakers, and nothing at low volume. I turn on music, and theres nothing. If I turn the volume all the way up, theres distortion, white noise, and a bunch of static, but I can hear the music very faintly. I've disabled the onboard audio, and followed the FAQ, but nothing. Any ideas?
Output volume is set with "Wave" and "Master" controls. Max the Wave and control with Master.
In many cases if PSU is weak --> you get issues of this type. Try to remove (temporarily) devices like CD/DVD, floppy, etc. (just remove power/data cables) to see if PSU is the culprit for your issue.
Also, have you checked/tried
- audio HW acceleration and SR conversion quality --> set both max
- audio codecs --> reinstallation can be helpful
- muted all other sources but the one(s) you're using (i.e. all other sources can be muted if only playing audio files)
- digital output only set properly (speaker settings/THX console)
- speakers connected as should (2/2. --> green jack, etc.) and plugs properly pushed in
- speakers set correct (2/2., 4/4., 5., 6/6., 7.)
- used different output device drivers on audio players (DS/MME/WDM/...)
- ASIO capable player --> shows if you have sound driver issue (creative/windows)
- reinstalled directX, WMP (updates audio codecs)
- etc.
jutapaMessage Edited by jutapa on 03-09-200609:34 AM

Computer freezes, then a low-volume, high pitch sound

Hello there,
My trusty 2002 MDD is randomly freezing on me for the 1st time! Disk Warrior nor Disk Utility form external boot-ups detect anything wrong. Thus, it doesn't seem to be a hard drive issue. Memory status on System Profiler checks OK.
Once the beach ball appears I can't do anything but press the power button to shut it down. I've noticed that while frozen a very low-volume, high pitch sound can be heard. ???
Thanks a lot for any feedback that you may provide,
Jacobo

Hatter,
Thanks for the prompt reply. Like you proposed, I've started from my FW drive (not after a freeze though) and everything drive-related checks OK.
Yes, my video card (Radeon 9800) does have a fan. I've though about this and the PSU as well. The latter is the quieter, less powerful one.
My drives are less than a year old and seem to be OK.
I’ve run Applejack (w/ memory check) and all is good.
Can the Apple Diagnostic CD pinpoint any of these issues?
My MDD has been incredible when it comes to reliability. She has not given me ANY problems whatsoever while stressed to its limits.
Thanks again for your time,
Jacobo

Fix low volume output on Sky HD Boxes

Here a suggestion for you. Why dont you fix the low volume out on the Sky HD boxes? Loads of people have complained about it. Do something about it.

I have finally found a very cost effective solution to this problem. Cancelled Sky subscription and got Freesat with a Humax box. This does not have the fault that the Sky HD boxes have. In fact it has an "on the remote" volume control, and when this is turned to max the volume is exactly as it should be. The volume control works both the HDMI and the analogue outputs. Additionally there is also a mute button on the remote, again muting both outputs. Perfect. Cost effective because since I have been a Sky subscriber for over a decade, now cancelled, assuming I would have stayed with them for another decade I have saved myself £4121 including the initial cost of the Freesat box. Quite a shocking amount of money that I will be saving, having calculated it. Shame on Sky for not correcting this software issue when it was first reported by many users, especially as the volume function used to be there and they removed it. For those thinking of doing the same as me, the Freesat / Freetime system is excellent, the EPG is as good as Sky and the "roll back" TV aspect of the EPG far superior to that of Sky. Picture quality is at least as good (probably better as box is Full HD) The BBC iplayer implementation is also not the "cut down" version thst Sky have also implemented (another software short cut that bugged me), i.e. it is the same as you'd see on your PC / smart TVs with FULL programme content. What you don't get is Sky Atlantic but since I never watched this in over a decade made no difference to me.

Audio out low volume

Our Motorola qip6416-2 suddenly is producing a very low volume on the volume out connectors. Volume to the TV is OK, but we have both a stereo and a TV-Anywhere hooked up to the audio out, and the volume on both has taken a sudden plunge. Any suggestions on settings that might need to be adjusted?
Thanks

Try looking at the compression setting and the fixed or adjustable setting (all under menu => audio).
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

Logic 9 ultrabeat has low volume!!

Similar Messages

Maybe you are looking for