Low Transfer Rate On 2960-S Switch

Hi,
I have 2 PCs (1gbps lan card each ) connected to Cisco 2960-S switch.
The bandwidth of all ports on 2960-S is set to 1gbps manually.
However whenever I transfer any file between the two I don't get transfer rate more than 12MBps/96mbps.
Theoretically it should be 125MBps but why am I getting such low transfer rate?
Regards.

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Bandwidth is set manually, eh? Have you checked for a duplex mixmatch?

Similar Messages

E4200 - low transfer rate

My laptop has internal wireless N and my transfer rate is 58 which I should get at least 300.
What's great about it: The guest connection
What's not so great: Can't get the faster transfer speed

There are a lot of factors that come into play with regards to your connection speed. A few things to keep in mind:
1) In order to get the best possible speed, your security mode needs to be either at WPA2-AES or disabled. I don't see this as your problem, otherwise your connection would be capped at 54Mbps and not reach the 58Mbps that you've mentioned.
2) Placement of the router. It matters a lot. The wireless signals typically travel better from higher to lower, and the router's signals get affected if the device is placed in a corner. This affects N routers more so than the older G routers because of the technology used in the newer devices.
3) Interference from other devices on the same frequency or from other wireless networks. This one is a fairly common one. Most wireless networks operate on the 2.4Ghz frequency, as do appliances like microwaves and cordless telephones and even Bluetooth devices. All these will end up causing interference to your network and affect speed and range. The simplest thing to do is change the channel on the router.
Hope this helps you out. Please post back if you need any more help.

Low transfer rate with NAT/Duplex/Speed settings

Hi all, I'm having this problem and I cannot find any bug or TAC case in the collection. I'm using PAT between two ethernet interfaces on a c3745 or c3845(I tried both in a lab).
If I keep the duplex and speed negociation to auto, everything works fine and it autonegotiates to full/100, but as soon as I force the duplex to full and speed to 100, the transfer rate of my FTP drops considerably. When I change the speed back to auto everything goes back to normal. I've tried the latest IOS but the problem persist.
Anyone experienced the same problem? Any ideas?
Thanks in advance,
Mariano

Fixing speed and duplex must be done on both sides. If one end remains in auto-mode the connection will default to half duplex.
This will result in a duplex mismatch between the devices.
http://www.cisco.com/univercd/cc/td/doc/cisintwk/itg_v1/tr1904.htm
regards,
Leo

Usb transfer rate problem with bootcamp

hello
drivers for uEye cameras are only available for windows platforms. so i am running windows xp on the latest mac mini with the latest bootcamp drivers in order to use the camera.
everything works great until i plug in another usb device. the transfer rate of the camera decreases dramatic (1/2). the second usb device is an usb hub with a microcontroller. it consumes only low transfer rates.
this constellation works perfect on other pcs. i can't compare it on os x because no drivers for the camera are available.
are there known issues with usb transfer rates on intel mac minis? firewire cameras and harddrives should suffer similar problems.
greetings
michael

are there known issues with usb transfer rates on
intel mac minis? firewire cameras and harddrives
should suffer similar problems.
Welcome to Apple Discussions!
To address this specific point - no, there are no known issues with USB transfer rates that are common to Macs but not PCs. The weakness of the USB standard is that it is controlled by the host system rather than a dedicated controller, thus transfer rates (on both Mac and PC platforms) are determined by what the system is doing overall. As a result, transfer rates vary quite dramatically. Firewire, on the other hand, has a dedicated controller which ensures that a consistent data rate is achieved, almost regardless of other system activity. That's why you will often see it recommended that FW is used for external drives rather than USB, since while USB will generally provide better burst rates of data transfer, FW will generally provide far better sustained data rates, despite being theoretically slower.
In your situation, I can't help but wonder if the hub you mention is not causing the system some issues. It would not have to be a matter of it causing any significant data transfer itself, but could be the result of the hub's controller forcing the system into activity which then suppresses potential performance from the camera.
One thing is sure: if the camera works well without the hub connected, but degrades in performance with it, the issue is not with the system or the camera, but the hub.

K9N SLI PLATINUM low data transfer rate

Hi, (sorry for my pour english) I had to go back to Winxp native SATA/IDE drivers and my pc crash & BSOD problem it's gone! :D (BSOD when i install some programs or some games, listening music and moving data at the same time, etc.) now i'm available to execute multitasks without any troubles. But now the transference it's quite poor , I think this is an easy and temporary solution for this big problem.
I bought my PC on 2006 and the Windows XP drivers are from 2001, aren't new Nvidia/MSI drivers to fix this annoying problem?
Thanks.
AM2 3800+ X2
MSI K9N SLI PLATINUM, bios 1.4
2 x 1GB OCZ DDR2 6400 Platinum
PSU PowerCooler 550w
HD WD3200 SATAII
NX7900GT

I've got nearly the same problem, but a little worse. My data transfer rate seems very slow for a 100mb network and if I start copying files over the network, after only a couple of megs I lose connectivity to the network completely! I've removed the network cable and windows notices this, and when I put it back in windows also notices the change, but the green and orange lights on the port itself stay on solid. If I reboot windows everything comes back. I don't have problems browsing the web, seems to only happen when the ethernat port is running close to full load (for the connection speed of 100mb as apposed to 1gb).
Anyone else seen this? I'm on the latest drivers, the latest bios and I've tried disabling on of the network ports in the bios but his didn't work.
Kevpatts

Wireless actually transfer rate seems a bit low

Hi all,
Something I was just wondering was what makes the BT HomeHub 3 decrease its actual transfer rate on Wireless as I am currently sat at on a Wireless connection that the Wireless adapter says it is connected at 39.0 mbs and then I look on the Hub and it says 11mbs and I am the only one connected to it. How come these stats don't match? To me they should.

Are you using the HomeHub with the version 4.7.5.1.83.8.57.1.3 (TypeA) (http://bt.custhelp.com/app/answers/detail/a_id/32228) ? Because if so, then that firmware has a lot of bugs in it, and may be your explanation.
Interestingly I compared mine to my Mac and Hub 3 (Type B) and this is what it came out at:

ULN transfer rate (up2date) too low

Since several months ago the ULN transfer rate has been getting worse and worse on each and every one download (up2date). I'm just trying to update the OEL-5.1 with OEL-5.2, but it is impossible with the transfer rate of 39 kB/s. My average transfer rate is 1.8 MB/s.
Has anyone else experienced the same?

I've already posted my ULN data to T.R. to be further investigated. For your info
Can you provide some details about your network?No network at all, it's a development system located at my home with only one (non-shared) internet connection (ADSL-16000 kbits/sec = 1.95 MB/sec). Here are some transfer rates on another sites to compare to:
* edelivery.oracle.com/linux      1.6 - 1.7 MB/sec
* OTN (11g download)              1.7 - 1.8 MB/sec
* java.sun.com                    1.7 - 1.8 MB/sec
* many Fedora mirror sites        1.6 - 1.95 MB/sec
* etc, in average                 1.8 MB/sec
* etc, most frequently            1.7 MB/sec
Perhaps someone is downloading Indiana Jones and the kingdom of the
crystal skull, for example...Perhaps, but not using my connection. BTW, what's your transfer rate at ULN (in average, most frequently, and right now)?

Solaris 10 u5 Samba slow transfer rates?

Hi!
I've installed Solaris 10 x86 (Core2Duo - x64) server, with Samba over ZFS RAID-Z. Samba is a part of Active Directory Domain. I've managed to join it to domain, to get the users and groups from A.D. and to translate them to Unix IDs. Everything works really good. Samba is installed from the packages from Solaris 10 DVD.
Only problem I have is the performance :( It's disastrous!
On 100Mbit Realtek NIC, Samba can manage around 4 MB/s if log level is set to very high (10). If I lower it to 0, then transfer rates go up to 7.5-8.5MB/s and they fluctuate in that interval.
On the same network, there is a Debian Samba server, and transfer rates go high as 10.5-11.0MB/s.
Next test I did was switching to Gbit interface. That increased transfer rates up to 25 MB/s, but that is still 5 times slower than the theoretical limit.
So, next thing I've tried was to switch to Blastwave (CSW) Samba instead of SUNW Samba.... My transfer rates went back to normal immediately! It was a bit of shock for me... I could transfer about 10MB/s on 100Mbit interface, and around 45MB/s on 1Gbit interface. 45MB/s is theoretically limit of the workstation hard drive I was doing transfers from.
Sun packaged (SUNW) Samba is 3.0.28 patched today to the latest patchlevel, and CSW uses 3.0.23. I used CSW Samba with the exact same smb.conf file. Only problem is - I never managed to connect CSW samba to ADS on my network :( So I gave up on that, and I'm facing a dilemma. Managers request full speed of the Samba server (comparable to Linux/Windows shares), but I just can't connect to Domain with CSW package.
So I'm asking you guys - any ideas what could be the problem with SUNW Samba and performance? Is it just the 3.0.28 vs 3.0.23 issue, or what? Why is there so big difference in transfer rates? :(
Please help!

OK, here goes my smb.conf:
[global]
workgroup = MYCOMPANY
realm = MYCOMPANY.LOCAL
server string = server4 (Samba, Solaris 10)
security = ADS
map to guest = Bad User
obey pam restrictions = Yes
password server = server1.mycompany.local
passdb backend = tdbsam
log file = /var/samba/log/log.%m
max log size = 50
socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE
load printers = No
local master = No
domain master = No
dns proxy = No
idmap uid = 10000-90000
idmap gid = 10000-90000
winbind separator = +
winbind enum users = Yes
winbind enum groups = Yes
winbind use default domain = Yes
[share]
comment = Share on ZFS Raid-Z
path = /tank/share
force user = local_user
force group = users
read only = No
guest ok = Yes
vfs objects = zfsacl

Transfer rate on Gigabit Network

Hello,
I have a gigabit network, with the network / s to 1 Gb stations, servers Team network card with 2 gb / s boards,
Switch Dell N 2048 also Gb. Cables Shielded CAT 6, and finally network certified.
Doubts and my problem is the following:
If I pick a folder that is in one FileServer, this folder has files of word, excel, pdf, etc., with the size of 200 mb, and transfer to another server or workstation, the transfer rate shows that the Windows is
5.6 mb / s (ie very low for a gigabit network)
But if I get a single file from Word, Excel, or PDF, that has the size of 200 mb, the transfer rate to about 60, 70, 80 mb / s
If I did also like the test, I took a .BAK file (backup of a database that had 20 gb), and start transferring the transfer rate goes to 100, 120 mb / s.
My question is, since the first case of the example the rate is only 5.6 and the other for another 50 mb / s.
Is it because I'm downloading several files at a time? or have something wrong with my network?
Note: All the above examples were made from the same server to the same station and vice versa.

Hi Tiago,
We've not heard from you yet. I assume the information provided by Darien has helped. I am marking this reply as answered now.
In case the information did not help, please feel free to unmark the answer and come back to us with your comments.
Best Regards.
Steven Lee
TechNet Community Support

How to find the max data transfer rate(disk speed) supported by mobo?

I plan on replacing my current HDD with a new and bigger HDD.
For this I need to know the max data transfer rate(disk speed) that my mobo will support. However, dmidecode is not telling me that. Am I missing something?
Here's dmidecode:
# dmidecode 2.11
SMBIOS 2.5 present.
80 structures occupying 2858 bytes.
Table at 0x000F0450.
Handle 0xDA00, DMI type 218, 101 bytes
OEM-specific Type
Header and Data:
DA 65 00 DA B2 00 17 4B 0E 38 00 00 80 00 80 01
00 02 80 02 80 01 00 00 A0 00 A0 01 00 58 00 58
00 01 00 59 00 59 00 01 00 75 01 75 01 01 00 76
01 76 01 01 00 05 80 05 80 01 00 D1 01 19 00 01
00 15 02 19 00 02 00 1B 00 19 00 03 00 19 00 19
00 00 00 4A 02 4A 02 01 00 0C 80 0C 80 01 00 FF
FF 00 00 00 00
Handle 0xDA01, DMI type 218, 35 bytes
OEM-specific Type
Header and Data:
DA 23 01 DA B2 00 17 4B 0E 38 00 10 F5 10 F5 00
00 11 F5 11 F5 00 00 12 F5 12 F5 00 00 FF FF 00
00 00 00
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Dell Inc.
Version: A17
Release Date: 04/06/2010
Address: 0xF0000
Runtime Size: 64 kB
ROM Size: 4096 kB
Characteristics:
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
EDD is supported
Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
ACPI is supported
USB legacy is supported
BIOS boot specification is supported
Function key-initiated network boot is supported
Targeted content distribution is supported
BIOS Revision: 17.0
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: Dell Inc.
Product Name: OptiPlex 755
Version: Not Specified
UUID: 44454C4C-5900-1050-8033-C4C04F434731
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0200, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Dell Inc.
Product Name: 0PU052
Version:
Handle 0x0300, DMI type 3, 13 bytes
Chassis Information
Manufacturer: Dell Inc.
Type: Space-saving
Lock: Not Present
Version: Not Specified
Asset Tag:
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
Handle 0x0400, DMI type 4, 40 bytes
Processor Information
Socket Designation: CPU
Type: Central Processor
Family: Xeon
Manufacturer: Intel
ID: 76 06 01 00 FF FB EB BF
Signature: Type 0, Family 6, Model 23, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (FXSAVE and FXSTOR instructions supported)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Multi-threading)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Not Specified
Voltage: 0.0 V
External Clock: 1333 MHz
Max Speed: 5200 MHz
Current Speed: 2666 MHz
Status: Populated, Enabled
Upgrade: Socket LGA775
L1 Cache Handle: 0x0700
L2 Cache Handle: 0x0701
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Core Count: 2
Core Enabled: 2
Thread Count: 2
Characteristics:
64-bit capable
Handle 0x0700, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 32 kB
Maximum Size: 32 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: None
System Type: Data
Associativity: 8-way Set-associative
Handle 0x0701, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Varies With Memory Address
Location: Internal
Installed Size: 6144 kB
Maximum Size: 6144 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Single-bit ECC
System Type: Unified
Associativity: <OUT OF SPEC>
Handle 0x0800, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: PARALLEL
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-25 female
Port Type: Parallel Port PS/2
Handle 0x0801, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: SERIAL1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x0802, DMI type 126, 9 bytes
Inactive
Handle 0x0803, DMI type 126, 9 bytes
Inactive
Handle 0x0804, DMI type 126, 9 bytes
Inactive
Handle 0x0805, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0806, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB2
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0807, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB3
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0808, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB4
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0809, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB5
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080A, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB6
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080B, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB7
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB8
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: ENET
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: RJ-45
Port Type: Network Port
Handle 0x080E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MIC
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x080F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0810, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-IN
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0811, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: HP-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0812, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MONITOR
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-15 female
Port Type: Video Port
Handle 0x090A, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT1
Type: x1 Proprietary
Current Usage: In Use
Length: Long
Characteristics:
PME signal is supported
Handle 0x0901, DMI type 126, 13 bytes
Inactive
Handle 0x0902, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
3.3 V is provided
PME signal is supported
Handle 0x0903, DMI type 126, 13 bytes
Inactive
Handle 0x0904, DMI type 126, 13 bytes
Inactive
Handle 0x0905, DMI type 126, 13 bytes
Inactive
Handle 0x0906, DMI type 126, 13 bytes
Inactive
Handle 0x0907, DMI type 126, 13 bytes
Inactive
Handle 0x0908, DMI type 126, 13 bytes
Inactive
Handle 0x0A00, DMI type 10, 6 bytes
On Board Device Information
Type: Video
Status: Disabled
Description: Intel Graphics Media Accelerator 950
Handle 0x0A02, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: Intel Gigabit Ethernet Controller
Handle 0x0A03, DMI type 10, 6 bytes
On Board Device Information
Type: Sound
Status: Enabled
Description: Intel(R) High Definition Audio Controller
Handle 0x0B00, DMI type 11, 5 bytes
OEM Strings
String 1: www.dell.com
Handle 0x0D00, DMI type 13, 22 bytes
BIOS Language Information
Language Description Format: Long
Installable Languages: 1
en|US|iso8859-1
Currently Installed Language: en|US|iso8859-1
Handle 0x0F00, DMI type 15, 29 bytes
System Event Log
Area Length: 2049 bytes
Header Start Offset: 0x0000
Header Length: 16 bytes
Data Start Offset: 0x0010
Access Method: Memory-mapped physical 32-bit address
Access Address: 0xFFF01000
Status: Valid, Not Full
Change Token: 0x00000018
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: System limit exceeded
Data Format 2: System management
Descriptor 3: Log area reset/cleared
Data Format 3: None
Handle 0x1000, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 8 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x1100, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_1
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Manufacturer: AD00000000000000
Handle 0x1101, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_3
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1102, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_2
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1103, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_4
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1300, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000FDFFFFFF
Range Size: 4064 MB
Physical Array Handle: 0x1000
Partition Width: 1
Handle 0x1400, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1100
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1401, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1101
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1402, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1102
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1403, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1103
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1410, DMI type 126, 19 bytes
Inactive
Handle 0x1800, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Enabled
Keyboard Password Status: Not Implemented
Administrator Password Status: Enabled
Front Panel Reset Status: Not Implemented
Handle 0x1900, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: *-* 00:00:00
Handle 0x1B10, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD00
Handle 0x1B11, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD01
Handle 0x1B12, DMI type 126, 12 bytes
Inactive
Handle 0x1B13, DMI type 126, 12 bytes
Inactive
Handle 0x1B14, DMI type 126, 12 bytes
Inactive
Handle 0x2000, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x8100, DMI type 129, 8 bytes
OEM-specific Type
Header and Data:
81 08 00 81 01 01 02 01
Strings:
Intel_ASF
Intel_ASF_001
Handle 0x8200, DMI type 130, 20 bytes
OEM-specific Type
Header and Data:
82 14 00 82 24 41 4D 54 01 01 00 00 01 A5 0B 02
00 00 00 00
Handle 0x8300, DMI type 131, 64 bytes
OEM-specific Type
Header and Data:
83 40 00 83 14 00 00 00 00 00 C0 29 05 00 00 00
F8 00 4E 24 00 00 00 00 0D 00 00 00 02 00 03 00
19 04 14 00 01 00 01 02 C8 00 BD 10 00 00 00 00
00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00
Handle 0x8800, DMI type 136, 6 bytes
OEM-specific Type
Header and Data:
88 06 00 88 5A 5A
Handle 0xD000, DMI type 208, 10 bytes
OEM-specific Type
Header and Data:
D0 0A 00 D0 01 03 FE 00 11 02
Handle 0xD100, DMI type 209, 12 bytes
OEM-specific Type
Header and Data:
D1 0C 00 D1 78 03 07 03 04 0F 80 05
Handle 0xD200, DMI type 210, 12 bytes
OEM-specific Type
Header and Data:
D2 0C 00 D2 F8 03 04 03 06 80 04 05
Handle 0xD201, DMI type 126, 12 bytes
Inactive
Handle 0xD400, DMI type 212, 242 bytes
OEM-specific Type
Header and Data:
D4 F2 00 D4 70 00 71 00 00 10 2D 2E 42 00 11 FE
01 43 00 11 FE 00 0F 00 25 FC 00 10 00 25 FC 01
11 00 25 FC 02 12 00 25 FC 03 00 00 25 F3 00 00
00 25 F3 04 00 00 25 F3 08 00 00 25 F3 0C 07 00
23 8F 00 08 00 23 F3 00 09 00 23 F3 04 0A 00 23
F3 08 0B 00 23 8F 10 0C 00 23 8F 20 0E 00 23 8F
30 0D 00 23 8C 40 A6 00 23 8C 41 A7 00 23 8C 42
05 01 22 FD 02 06 01 22 FD 00 8C 00 22 FE 00 8D
00 22 FE 01 9B 00 25 3F 40 9C 00 25 3F 00 09 01
25 3F 80 A1 00 26 F3 00 A2 00 26 F3 08 A3 00 26
F3 04 9F 00 26 FD 02 A0 00 26 FD 00 9D 00 11 FB
04 9E 00 11 FB 00 54 01 23 7F 00 55 01 23 7F 80
5C 00 78 BF 40 5D 00 78 BF 00 04 80 78 F5 0A 01
A0 78 F5 00 93 00 7B 7F 80 94 00 7B 7F 00 8A 00
37 DF 20 8B 00 37 DF 00 03 C0 67 00 05 FF FF 00
00 00
Handle 0xD401, DMI type 212, 172 bytes
OEM-specific Type
Header and Data:
D4 AC 01 D4 70 00 71 00 03 40 59 6D 2D 00 59 FC
02 2E 00 59 FC 00 6E 00 59 FC 01 E0 01 59 FC 03
28 00 59 3F 00 29 00 59 3F 40 2A 00 59 3F 80 2B
00 5A 00 00 2C 00 5B 00 00 55 00 59 F3 00 6D 00
59 F3 04 8E 00 59 F3 08 8F 00 59 F3 00 00 00 55
FB 04 00 00 55 FB 00 23 00 55 7F 00 22 00 55 7F
80 F5 00 58 BF 40 F6 00 58 BF 00 EB 00 55 FE 00
EA 00 55 FE 01 40 01 54 EF 00 41 01 54 EF 10 ED
00 54 F7 00 F0 00 54 F7 08 4A 01 53 DF 00 4B 01
53 DF 20 4C 01 53 7F 00 4D 01 53 7F 80 68 01 56
BF 00 69 01 56 BF 40 FF FF 00 00 00
Handle 0xD402, DMI type 212, 152 bytes
OEM-specific Type
Header and Data:
D4 98 02 D4 70 00 71 00 00 10 2D 2E 2D 01 21 FE
01 2E 01 21 FE 00 97 00 22 FB 00 98 00 22 FB 04
90 00 11 CF 00 91 00 11 CF 20 92 00 11 CF 10 E2
00 27 7F 00 E3 00 27 7F 80 E4 00 27 BF 00 E5 00
27 BF 40 D1 00 22 7F 80 D2 00 22 7F 00 45 01 22
BF 40 44 01 22 BF 00 36 01 21 F1 06 37 01 21 F1
02 38 01 21 F1 00 39 01 21 F1 04 2B 01 11 7F 80
2C 01 11 7F 00 4E 01 65 CF 00 4F 01 65 CF 10 D4
01 65 F3 00 D5 01 65 F3 04 D2 01 65 FC 00 D3 01
65 FC 01 FF FF 00 00 00
Handle 0xD403, DMI type 212, 157 bytes
OEM-specific Type
Header and Data:
D4 9D 03 D4 70 00 71 00 03 40 59 6D 17 01 52 FE
00 18 01 52 FE 01 19 01 52 FB 00 1A 01 52 FB 04
1B 01 52 FD 00 1C 01 52 FD 02 1D 01 52 F7 00 1E
01 52 F7 08 1F 01 52 EF 00 20 01 52 EF 10 21 01
52 BF 00 22 01 52 BF 40 87 00 59 DF 20 88 00 59
DF 00 E8 01 66 FD 00 E9 01 66 FD 02 02 02 53 BF
00 03 02 53 BF 40 04 02 53 EF 00 05 02 53 EF 10
06 02 66 DF 00 07 02 66 DF 20 08 02 66 EF 00 09
02 66 EF 10 17 02 66 F7 00 18 02 66 F7 08 44 02
52 BF 40 45 02 52 BF 00 FF FF 00 00 00
Handle 0xD800, DMI type 126, 9 bytes
Inactive
Handle 0xDD00, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 00 DD 00 01 00 00 00 10 F5 00 00 00 00 00
00 00 00
Handle 0xDD01, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 01 DD 00 01 00 00 00 11 F5 00 00 00 00 00
00 00 00
Handle 0xDD02, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 02 DD 00 01 00 00 00 12 F5 00 00 00 00 00
00 00 00
Handle 0xDE00, DMI type 222, 16 bytes
OEM-specific Type
Header and Data:
DE 10 00 DE C1 0B 00 00 10 05 19 21 01 00 00 01
Handle 0x7F00, DMI type 127, 4 bytes
End Of Table
Hdparm also does not tell me the max data transfer rate (disk speed) of my current drive although this link : www.wdc.com/en/library/sata/2879-001146.pdf says that it is 3.0Gb/s
and here's hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: WDC WD800JD-75JNC0
Firmware Revision: 06.01C06
Standards:
Supported: 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156250000
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 76293 MBytes
device size with M = 1000*1000: 80000 MBytes (80 GB)
cache/buffer size = 8192 KBytes
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 8
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
Automatic Acoustic Management feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* SMART error logging
* SMART self-test
* Gen1 signaling speed (1.5Gb/s)
* Host-initiated interface power management
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Last edited by Inxsible (2011-03-27 04:40:49)

I just checked my BIOS and my current setting is set at IDE although it also mentions that the default should be AHCI. Currently I have a dual boot of Windows 7 (need it for Tax software) and Arch
So I guess, when I get the new HDD, I will first set it to AHCI and then install the OSes on it. See if NCQ helps any, and if not I will turn it back and re-install (if I have to). I am planning to have Windows only in virtualbox in the new drive.
Anyhoo, while I was in the BIOS I found two things which I had questions about :
1) Under Onboard Devices --> Integrated NIC , my setting is currently set at "On w/PXE" and it says the default should be just "On". Would it be ok to change it back to On since its a single machine and its not booting an OS on any server. I just don't want to have to re-install anything now since I will be doing that in the new HDD.
2) How would I know whether my BIOS would support a 64 bit OS in Virtualbox? I checked some setting under Virtualization, but they weren't very clear.
I will edit this post and let you know exactly what settings were present under the Virtualization sub-section.

Gigabit ethernet + TC doesn't mean gigabit transfer rates to the TC drive..

Alright.... I've spent a ton of time trying to figure this out (probably more than I should have) and I thought I'd post my findings so that either a) I'll save someone else time out there or b) someone can tell me I'm a complete moron
So I had an airport extreme. I replaced it with a Time Capsule. I have a Windows (boooo) PC connecting directly to my TC using a gigabit ethernet card (which I bought specifically connect it to the TC) so (I thought) I could enjoy gigabit transfer speeds to the internal hard drive from the wired PC. I had some fun plans of shoving my itunes directory on the TC and letting appletv sync (yes through my pc) and keeping lots of videos there, etc. Who cares - it'd be at gigabit speeds! But, in reality, things didn't quite work that way (though my itunes directory does still live on my TC...for now).
Well, I had a semi-unique situation to do some pretty massive testing because I have 2 gigabit network cards, 1 100mb network card, and a wireless-n network card and two internal hard drives - both very fast. I also tried Cat 5, Cat 5e, and a Cat 6 cable.
And here's what I (think I) figured out:
The hard drive in TC can not achieve gigabit transfer speeds. Your transfer rates will be limited by the IO to the hard drive. In fact, it can't even come close.
Using my "fastest" setup - so Cat 6, fastest internal drive, gigabit ethernet, and transferring a file exactly 1 gig in size I was able to have a sustained transfer rate of 140 megabit per second - that's 17.4 MB/s for folks not wanting to do the math (that's reading FROM the TC. Writing TO the TC dropped the speed down to 106 megabit/second or 13.35 MB/s). Going to a 5e cable knocked that down to 130 megabit a second. Putting in a Cat 5 cable knocked me down to 110 megabit a second. Switching between my two gigabit network cards did nothing. Switching my cards between two computers did nothing.
Now, just changing the above setup to use my 100Mb network card resulted in these results: 67 megabit read (8.4MB/s) and 65 megabit write (8MB/s)...
And using wireless N, I got about 10MB/s up and down.
And just as a final test, connecting my two computers together using the 2 gigabit network cards through the TC, I was able to achieve standard gigabit speeds.
SO what does this all mean?
I think the IO to the hard drive in the TC can only read at about 140 megabit/s and write at about 110 megabit/s. I'm not sure if it's the HD itself or how it's connecting to the TC - but that's why I'm not aware of anyone getting faster transfer rates to the drive in the TC (maybe you guys are?). The gigabit ports themselves are fine - and if you're doing anything from one gigabit port to another gigabit port you'll be fine.
So stop beating yourself up trying to find some elusive XP specific issue with gigabit transfer rates (though vista had a problem - shocker), or that you must have a defective gigabit card (which is why I have two cards now instead of one :)), or that your cable must be bad ("maybe my cat 5e isn't good enough?")... it's just this drive ... or how the drive is connecting to the network - can't handle the gigabit speeds.
Unless someone else out there has another explanation? Do these speeds mesh with what you're seeing in "optimal" situations? Or maybe there's just a throttle switch for goobers like me using Windows instead of MacOS!

Hi,
the interfaces available today which connect your drives integrated electronics to your computer can handle that speeds. but the drive itself is limited by the mechanical things going on in there
You can get such transfer speeds if the data you request is in the cache of the drives internal electronics for example. Some drives have 8 MB of cache memory. So if you request to read or write less than 8 mb and (in the read case) you are lucky enough to have those few megabytes cached then you may get that performance
Regards,
somi

How to achieve the maximum file transfer rate from PXI to local host?

I will have to copy a huge amount of data (as big as 50 GB) from a PXI-8106 unit on site to a laptop. Currently it would take several hours. It is critical to max out the data transfer rate.
The standard method we've been using is just drag and drop using Windows Explorer via FTP. I tried to use FTP VIs with Filezilla Server as well but the transfer rate is only like 1.5 MB/s. Is this normal? Once I saw it was 3.0 MB/s but for some reason, that isn't happening now.
For another option, I tried to transfer data to a USB flash drive but it's even slower. As far as I know, USB 2.0 transfer rate is supposed to be around 60 MB/s but why would it be slower than 1.5 MB/s? What could be the speed limiting factor in my file transfer setup?
Any tips on improving file transfer rate would be appreciated!

Sustained 40 MB/s? That is my dream speed! The maximum speed I've ever seen here was about 25 MB/s, which is still very good, and that happened only after copying back and forth, which I explained above. Let me go through what I did with screencaps first.
These are the test tdms files to transfer in the PXI: an original file witten in the PXI and its copy file. I copied the original file from PXI to laptop and renamed it (added '_copy') and then copied it back to PXI.
FTP module is transferring the original file to the Filezilla server on laptop. Note the low speed.
FTP module is transferring the copy file to the Filezilla server on laptop. Note the higher speed.
This is the FTP sub VI I'm using. It transfers files in sub-folders (one level lower), too. The data connection is set to 'passive' on the FTP Put Multiple Files VI but it doesn't seem to make any difference. I attach the sub VI.
You tried the file transfer with a 500 MB text file. Would there be any difference if the file type was tdms? Would the RAM size matter? It is 2GB here.
And the LED is orange, which means Gigabit.
Another question: Is there any way to programmatically stop file transfer in progress? Currently, I just have to restart the PXI.
Thank you!
Attachments:
FTP.vi ‏40 KB

Clients Connect to N AP's on 5508 and get different Transfer rates than on 4404

I have have 2x 4404's (2x) and 2x 5508's all are running 7.0.240.0. When I take an 1142 and associate it to a 4404 I can connect a test client using N at 144Mbps and I can get transfer rates averaging 70Mbps (using iperf tests). When I take the same AP and associate it to a 5508, (same SSID, etc) I connect at 144Mbps but only get average 6Mbps transfer rates. I get the same results with 1252's. I get the same results if I wipe the config on the 5508 and start from scratch. It only happens when connecting at a/n, when I use a b/g AP such as 1132 I connect at 54Mbps on either controller and get transfer rates of 24Mbps. I have enabled disabled LAG (rebooted), moved the 5508 to connect to the same swtich ports, swapped GBICs. The issue happens on both 5508s, TAC has been unable to resolve this and they are confused as well.
Some of the other things I have tried:
•-          You are facing the issue on 5508's WLC only.
•-          Both the WLC and the client reports high connection speed “144Mbps”
•-          iPerf between wireless and wired showed the following:
on 4400: [124] 0.0-16.9 sec   154 MBytes 76.5 Mbits/sec
On 5500: [124] 0.0-94.3 sec 70.2 MBytes 6.25 Mbits/sec
•-          The AP is the same AP, you just bounce it from 1 WLC to another.
•-          The location of the AP is the same in all the tests, but it can be replicated with an 1142 anywhere on site and get the same results.
•-          The test PC is the same in both cases
•-          The configuration is the same on both WLC’s confirmed visaully in GUI and via CLI outputs and compaired.
•-          The switch is the same, but have tired swapping 4404 and 5508 in data center.
•-          Tried to swap the GBICs.
•-          Used different ports on the 5508 (not just diff GBICs)
•-          Disabled the LAG to rule out the load balancing algorithm.
•-       Replaced the patch cables
Used same ip space that the 4404 is using without sucess.
Upgraded my second 5508 to version 7.5 and exact same resutls.
Any ideas?

Hi
In my 5508 WLC i have exactly the same problem as you gsutherland
I tried apply this command config 802.11b 11nSupport a-mpdu tx priority all disable
and i get message
"802.11b network not disabled"
Why i must turn off b standard ?
Thanks for respons

Z77 gd65 gaming slow hdd transfer rate plz help

my specification
1. intel g2020 2.9ghz
2. ram 8gb patriot ddr3 1600 set in bios
3. motherboard z77 gd 65 gaming and non gaming
4. 8 hdisk sata 3 each 3tb wdc green ezrx
5. psu seasonic x760watt gold
6. win 7 64bit
bios setting
sata set to ahci
eksternal sata set to ahci
problem is
before i clean install my pc , one of my hdd died.
my transfer rate beetween internal hdd is very good, iam using teracopy 2.3
speed is 80-100mb/s.
transfer speed from internal hdd to eksternal hdd (wdc mybook usb 3) also good 70-90mb/s
but now after clean install windows 7 64bit
teracopy speed down to 40-50mb/s
nothing changed from hardware but the copy speed is very low now
bios setting still like the same all sata set to ahci
all driver in device manager is installed
i have tried 3 times clean install win7 hope to get back the normal copy speed but nothing changed iam stuck at max 56mb/s
plz someone who ever experience or know the solution help me
thank you very much before

Hi,
Have you installed ALL the drivers before you made any tests?
You might also want to Clear the BIOS (Copied from Troubleshooting Guide V1.0 as I couldn't find the link for just clearing the Bios):
Quote
Clearing the CMOS chip
Disconnect the system power cord and push the case power button to drain all remaining power in the psu for approximately 15 seconds
Then move jumper jbat1 and wait 10 seconds and move it back to the original position. You should ensure that the jumper has metal inside of it when removed, sometimes (rarely) they don't. This process resets or clears the CMOS chip and is shown in most motherboard manuals.Now connect the power cord and restart your system.
Some motherboards require that the battery must be removed for 20 minutes before putting the battery and jbat1 back for the CMOS chip to be cleared.

Recovery missing or corrupted IOS of Cisco 2960 Catalyst Switch

Dear Team,
I have Cisco 2960 48P switch, It is keep getting restarted and config was erased.
when I tried to run the IOS from hypertrm in room mode, I am getting below error..
My doubt is, is there any issue with hardware & what is the cause of for below error
suggest me, is there any option to upgrade the IOS?
switch: flash_init
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 32513024
flashfs[0]: flashfs fsck took 9 seconds.
...done Initializing Flash.
switch: copy xmodem: flash:c2960-lanbasek9-mz.122-50.SE5.bin
Begin the Xmodem or Xmodem-1K transfer now...
CCCCBB0BB0................flashfs[0]: filesystem marked down. Use "fsck" to rec
over.
flash:c2960-lanbasek9-mz.122-50.SE5.bin: interrupted system call
switch:

Error message means your BIN file is corrupt. You need to download again from the Cisco website.

Low Transfer Rate On 2960-S Switch

Similar Messages

Maybe you are looking for