Maddening perplexing HD issue!

Hi all, this is going to be long winded, so bear with me...
This is hands down the STRANGEST problem I personally have ever encountered in my 10+ years working with Macs. I recently acquired a new HD for my early '08 MBP. It is a Fujitsu (M# MHZ2320BJ) 320GB 7200 RPM drive that was originally enclosed in a Rocstor enclosure. I decided to remove it from the enclosure and use it as my internal drive as it's both faster and larger than my stock drive. So, before installing, I cloned my original drive to the new one using CCC, installed the new drive, and it booted fine. No problems. I did some some application updating and what not and rebooted. When the computer rebooted, I got the startup tone and a grey screen, and thats as far as it ever went. No apple logo. After a few minutes of waiting, I got the dreaded flashing ? folder. So I put in my Snow Leopard DVD and rebooted, holding the C key. Nothing. I rebooted again and held the option key. Nothing. So, I plugged in an external FW HD I have with a copy of the SL DVD cloned to it (for both backup and much faster installation purposes). Held the option key, and low and behold both the internal drive and the SL DVD showed up, along with the FW drive. Since my internal drive showed up, I clicked on it and it booted just fine. I unmounted my FW drive, rebooted again, and back to nothing, I would get zero boot options. So I did a little research. I ended up doing all the PRAM/NVRAM/PMU reset stuff, none of which worked. I booted from my SL DVD (which only worked when a FW drive was connected, ANY FW drive) and ran disk repair from the disk utilities app. Nothing would work. I even formatted and reinstalled SL on the internal drive, and when the installation was complete it rebooted to the internal drive just fine, no FW drive attached. So I let it do it's updates, and when it was again time for a reboot, nothing again, back to square one. So I pulled out the new HD, put in my original stock drive, and it booted immediately. Heard the tone, apple logo showed up about a second later, and I'm up and running, with nothing attached. On an interesting note, I took the new drive, which I had just installed SL on, and put it back into a FW enclosure, and there was a completely empty HD, named "untitled" (I had renamed the drive to Macintosh HD after the SL installation), as if nothing had ever been installed on it at all.
So, long story short, I have a drive that will ONLY boot when an external FW drive is attached. On top of that, when this drive is installed, NOTHING will boot unless an external FW drive is installed. The drive seems to operate just fine when installed in an external enclosure, but royally f**cks up my system when installed internally. Does anyone have any clue what would cause such behavior? I have never encountered anything like this before in my life. I'd still like to try to use this drive as my internal boot disk, so if anyone has any input/insight as to what might be causing this, I'd be grateful.
Thanks!

I think I'd try writing zero's to the drive using the disk utility from the Snow Leopard install DVD, then format the new internal drive (including checking for the GUID format in the options section), then install Snow Leopard as usual.

Similar Messages

Perplexing connectivity issue Please help

Hello,
I am a frequent user of skype and last week itself, on thurs and friday i had two international sessions of two hours that were uninterrupted. Today, i tried the same on skype and it kept disconnecting and dropping. I thought it was a skype issue, and I tried google hangouts and same errors on both sides. Both of our internet connections are stable and working. He is utilizing skype from his mobile phone because we are utilizing teamviewer for remote desktop viewings... Someone please help me with this issue of connectivity. I performed all necessary updates for my yosemite (mac) and also reset my router and internet. went to speedtest.net am at 65mbps and 4mbps respectively..... I dont know what is going on its quite frustrating.
There are no firewalls being implemented btw....

hello please help

Help on perplexing PS issue (side-by-side images)

Every once in a while I print that has two side-by-side images on one piece of paper. My usual routine is to create a new document that is larger than the two images--say, 10x8 (horizontal) with a transparent background and the same resolution as the two images that I'll be placing on the canvas (say, two 4x3's). Then I simply click on the image I want to move and drag it from its layers palette onto the blank background canvas, and move/edit/size as needed. Ditto with the second image. This has worked great for me.
Until tonight. Same routine. Except when I drag an image over to the blank canvas, it assumes the size of the entire canvas. so I just have the image... enlarged. With no background canvas.
This is driving me nuts. Anyone know what I'm doing wrong or if inadvertently hit some setting? BTW, when I click on the new image (the one dragged to the canvas), all of the editing commands are grayed out. So I cannot resize or move it.
I'm on CS5 (mac)
Thanks!

It seems way too obvious, but what are the pixel dimensions of the the two images? If I have two portrait mode images, for instance, I open both, and check their pixel size. Then the larger is downsized to the exact same height as the smaller, and the smaller image's Canvas size increased to the exact pixel width of the larger's. That way I know that the two will fit perfectly on one canvas.
Or I just use Picture package and save myself a heap of time!
BTW I have Picture Package in CS5, but not CS6. Can it still be DL'd as an xtra?
Ahhh... Check this thread
http://forums.adobe.com/message/4377236

Perplexing iPhoto issue - disappearing photos.

Currently have iPhoto 9.2.3, but also have a few other versions as a result of a so-called computer tech trying to resolve my problem. Which is, most of my photos disappeared. I see gray screen with white borders but no photos. Unless, I scroll quickly throught the gray screen. Then, I can glimpse the photos, but as soon as I stop scrolling the photos are gone.
What is going on here? How can I recapture my photos?

Apply the two fixes below in order as needed:
Fix #1
1 - launch iPhoto with the Command+Option keys held down and rebuild the library.
2 - run Option #4 to rebuild the database.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
1 - download iPhoto Library Manager and launch.
2 - click on the Add Library button and select the library you want to add in the selection window..
3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the Library ➙ Rebuild Library menu option.
4 - In the next window name the new library and select the location you want it to be placed.
5 - Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments. However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT

Perplexing Quality Issue: Itunes Rental VS Apple Tv Rental

Hello everyone, I have a quick question hopefully someone can help me out with. I find that when I purchase a rental directly from the Apple TV interface, the quality of the material is not quite as good as when I download it from iTunes and then Airplay stream it to my Apple TV. Why is this? Is this standard for everyone else? I have made sure both on iTunes and on Apple TV that my settings are at 1080p. It seems that allowing the movie to completely download via Itunes and then streaming it to the Apple TV yields better quality. Anyone experienceing the same thing?

Don't have any solutions to offer, but I sympathize, because I have had that occur in the past. A few images simply refused to sync from Smart Albums, for reasons which completely eluded me. Very frustrating!
The problem seemed to have resolved itself, but I always suspected the problem was mainly with the system-wide media browser (whatever it's called).

Perplexing color issue on HP Deskjet F4180

I just read the post about HP LIDIL printers being incompatible with AirPort connection, and indeed my printer is such, so this may explain why this happened; however, I think this merits mentioning anyway considering how head-scratchingly bizarre my printer has been behaving.
When I first set up my new MacBook and AirPort Express, the printer exhibited no problems whatsoever other than being unwilling to display information in the HP Ink Levels widget I temporarily added to my Dashboard. I tested it by printing a color-heavy page from the internet and it performed perfectly. A few days later my MacBook informed me of a massive download of software updates, which I believe included HP updates for the printer. Of course I allowed the installation without thought. Nothing else went awry, but the next time I tried to use my printer, I had the annoying surprise of a print output in only black/grayscale. I was printing from Photoshop, so at first I thought I had fouled up my file mode or printing preferences. But no matter what or how much I tinkered with, the printer refused to deliver any color. I did a self-test page and the color cartridge is certainly fine; the colors displayed properly on the paper in all the right places. Moreover, I just purchased new cartridges anyway.
Printing from the internet delivered the same results. I called HP phone support but they were unable to help me since the warranty had already run out. I will admit this printer has given me headaches even when I had it hooked up directly to my old PC laptop; I lost count of all the times I had to reinstall it.
Given the LIDIL information, what I don't comprehend is how this printer can manage to function with the basic action of printing, but only in black/grayscale. No, the Scan function doesn't work, and it's not listed in Photoshop's Import. The HP Photosmart Studio app closes within seconds of me opening it as well. I've been advised to reinstall it, but since I needed Apple phone support just to install the AirPort Express I dread pulling the plug and starting over.
Any other advice about this situation before I do my umpteenth reinstall for this beast? I do take the MacBook away from my desk at least once a week, which would require me to pull the USB printer cable out of it and thus force me to reinstall it over and over again anyway. It would pain me to have to consider replacing this printer, since it has worked very well when it does and I generally abhor throwing money down the drain.
Message was edited by: MoriahJS

Update: thanks to Bob Starr for posting the Linux downloads; I just installed them and my print output is now back to color. Still won't be able to scan, but oh well. It's not like I knew all this ahead of time when I first bought my printer.

Black Screen with Sound on OpenGL Apps (nVidia GeForce4 MX 440)

After a couple weeks of a non-stop search for a solution that has taken me through countless forums and Google queries, I've come to the realization that I need some help before I drive myself insane. I am running an old emachine T3065 with an AMD Athlon XP 2.167 MHz processor, 1024 MB of RAM, 160 GB HD, and a good old integrated (POS) nVidia NV18 GeForce4 MX 440 displayed on a widescreen Acer X191W LCD panel. I followed the instructions dictated in the nVidia installation wiki to a 'T', and can start GDM and log into Gnome without any conflict. Then when I attempt to launch a 3D OpenGL game or application, I'm stuck with a black screen where I can still hear sound (in fullscreen mode) or, in a few windowed programs such as foobillard and Google Earth, a three-dimensional shape without textures. Here's a couple screenshots:
http://img.photobucket.com/albums/v144/ … glwoes.png
http://img.photobucket.com/albums/v144/ … eearth.png
When I issue the glxinfo command, this is the result:
name of display: :0.0
display: :0 screen: 0
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.4
server glx extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_SGIX_fbconfig,
GLX_SGIX_pbuffer, GLX_SGI_video_sync, GLX_SGI_swap_control,
GLX_EXT_texture_from_pixmap
client glx vendor string: NVIDIA Corporation
client glx version string: 1.4
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_visual_info,
GLX_EXT_visual_rating, GLX_EXT_import_context, GLX_SGI_video_sync,
GLX_NV_swap_group, GLX_NV_video_out, GLX_SGIX_fbconfig, GLX_SGIX_pbuffer,
GLX_SGI_swap_control, GLX_NV_float_buffer, GLX_ARB_fbconfig_float,
GLX_EXT_fbconfig_packed_float, GLX_EXT_texture_from_pixmap
GLX version: 1.3
GLX extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_SGIX_fbconfig,
GLX_SGIX_pbuffer, GLX_SGI_video_sync, GLX_SGI_swap_control,
GLX_EXT_texture_from_pixmap, GLX_ARB_get_proc_address
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce4 MX Integrated GPU/PCI/SSE/3DNOW!
OpenGL version string: 1.5.8 NVIDIA 96.43.01
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_pixel_buffer_object,
GL_ARB_point_parameters, GL_ARB_point_sprite, GL_ARB_shader_objects,
GL_ARB_shading_language_100, GL_ARB_texture_compression,
GL_ARB_texture_cube_map, GL_ARB_texture_env_add,
GL_ARB_texture_env_combine, GL_ARB_texture_env_dot3,
GL_ARB_texture_mirrored_repeat, GL_ARB_texture_rectangle,
GL_ARB_transpose_matrix, GL_ARB_vertex_buffer_object,
GL_ARB_vertex_program, GL_ARB_vertex_shader, GL_ARB_window_pos,
GL_S3_s3tc, GL_EXT_texture_env_add, GL_EXT_abgr, GL_EXT_bgra,
GL_EXT_blend_color, GL_EXT_blend_minmax, GL_EXT_blend_subtract,
GL_EXT_clip_volume_hint, GL_EXT_compiled_vertex_array, GL_EXT_Cg_shader,
GL_EXT_draw_range_elements, GL_EXT_fog_coord,
GL_EXT_gpu_program_parameters, GL_EXT_multi_draw_arrays,
GL_EXT_packed_pixels, GL_EXT_paletted_texture, GL_EXT_pixel_buffer_object,
GL_EXT_point_parameters, GL_EXT_rescale_normal, GL_EXT_secondary_color,
GL_EXT_separate_specular_color, GL_EXT_shared_texture_palette,
GL_EXT_stencil_wrap, GL_EXT_texture_compression_s3tc,
GL_EXT_texture_cube_map, GL_EXT_texture_edge_clamp,
GL_EXT_texture_env_combine, GL_EXT_texture_env_dot3,
GL_EXT_texture_filter_anisotropic, GL_EXT_texture_lod,
GL_EXT_texture_lod_bias, GL_EXT_texture_object, GL_EXT_vertex_array,
GL_IBM_rasterpos_clip, GL_IBM_texture_mirrored_repeat,
GL_KTX_buffer_region, GL_NV_blend_square, GL_NV_fence,
GL_NV_fog_distance, GL_NV_light_max_exponent, GL_NV_packed_depth_stencil,
GL_NV_pixel_data_range, GL_NV_point_sprite, GL_NV_register_combiners,
GL_NV_texgen_reflection, GL_NV_texture_env_combine4,
GL_NV_texture_rectangle, GL_NV_vertex_array_range,
GL_NV_vertex_array_range2, GL_NV_vertex_program, GL_NV_vertex_program1_1,
GL_SGIS_generate_mipmap, GL_SGIS_multitexture, GL_SGIS_texture_lod,
GL_SUN_slice_accum
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x21 24 tc 0 32 0 r y . 8 8 8 0 4 24 8 16 16 16 16 0 0 None
0x22 24 dc 0 32 0 r y . 8 8 8 0 4 24 8 16 16 16 16 0 0 None
0x23 24 tc 0 32 0 r y . 8 8 8 8 4 24 8 16 16 16 16 0 0 None
0x24 24 tc 0 32 0 r . . 8 8 8 0 4 24 8 16 16 16 16 0 0 None
0x25 24 tc 0 32 0 r . . 8 8 8 8 4 24 8 16 16 16 16 0 0 None
0x26 24 tc 0 32 0 r y . 8 8 8 0 4 24 0 16 16 16 16 0 0 None
0x27 24 tc 0 32 0 r y . 8 8 8 8 4 24 0 16 16 16 16 0 0 None
0x28 24 tc 0 32 0 r . . 8 8 8 0 4 24 0 16 16 16 16 0 0 None
0x29 24 tc 0 32 0 r . . 8 8 8 8 4 24 0 16 16 16 16 0 0 None
0x2a 24 tc 0 32 0 r y . 8 8 8 0 4 16 0 16 16 16 16 0 0 None
0x2b 24 tc 0 32 0 r y . 8 8 8 8 4 16 0 16 16 16 16 0 0 None
0x2c 24 tc 0 32 0 r . . 8 8 8 0 4 16 0 16 16 16 16 0 0 None
0x2d 24 tc 0 32 0 r . . 8 8 8 8 4 16 0 16 16 16 16 0 0 None
0x2e 24 tc 0 32 0 r y . 8 8 8 0 4 0 0 16 16 16 16 0 0 None
0x2f 24 tc 0 32 0 r y . 8 8 8 8 4 0 0 16 16 16 16 0 0 None
0x30 24 tc 0 32 0 r . . 8 8 8 0 4 0 0 16 16 16 16 0 0 None
0x31 24 tc 0 32 0 r . . 8 8 8 8 4 0 0 16 16 16 16 0 0 None
0x32 24 dc 0 32 0 r y . 8 8 8 8 4 24 8 16 16 16 16 0 0 None
0x33 24 dc 0 32 0 r . . 8 8 8 0 4 24 8 16 16 16 16 0 0 None
0x34 24 dc 0 32 0 r . . 8 8 8 8 4 24 8 16 16 16 16 0 0 None
0x35 24 dc 0 32 0 r y . 8 8 8 0 4 24 0 16 16 16 16 0 0 None
0x36 24 dc 0 32 0 r y . 8 8 8 8 4 24 0 16 16 16 16 0 0 None
0x37 24 dc 0 32 0 r . . 8 8 8 0 4 24 0 16 16 16 16 0 0 None
0x38 24 dc 0 32 0 r . . 8 8 8 8 4 24 0 16 16 16 16 0 0 None
0x39 24 dc 0 32 0 r y . 8 8 8 0 4 16 0 16 16 16 16 0 0 None
0x3a 24 dc 0 32 0 r y . 8 8 8 8 4 16 0 16 16 16 16 0 0 None
0x3b 24 dc 0 32 0 r . . 8 8 8 0 4 16 0 16 16 16 16 0 0 None
0x3c 24 dc 0 32 0 r . . 8 8 8 8 4 16 0 16 16 16 16 0 0 None
0x3d 24 dc 0 32 0 r y . 8 8 8 0 4 0 0 16 16 16 16 0 0 None
0x3e 24 dc 0 32 0 r y . 8 8 8 8 4 0 0 16 16 16 16 0 0 None
0x3f 24 dc 0 32 0 r . . 8 8 8 0 4 0 0 16 16 16 16 0 0 None
0x40 24 dc 0 32 0 r . . 8 8 8 8 4 0 0 16 16 16 16 0 0 None
As you can see, direct rendering is enabled. This left me fairly perplexed.
Issuing glxgears returned a smooth animation without error running at an average of 1750 frames per second. I then began toying with my xorg.conf settings by turning "RenderAccel" on and off, trying the different "NvAGP" ranges, etc. All without revealing a solution. Here is my current xorg.conf:
Section "ServerLayout"
Identifier "Xorg Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "PS/2 Mouse" "CorePointer"
# Serial Mouse not detected
# USB Mouse not detected
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/PEX"
# Additional fonts: Locale, Gimp, TTF...
FontPath "/usr/share/fonts/cyrillic"
# FontPath "/usr/share/lib/X11/fonts/latin2/75dpi"
# FontPath "/usr/share/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see /etc/X11/XftConfig!
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/ttf/western"
FontPath "/usr/share/fonts/ttf/decoratives"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/latex-ttf-fonts"
FontPath "/usr/share/fonts/defoma/CID"
FontPath "/usr/share/fonts/defoma/TrueType"
EndSection
Section "Module"
Load "ddc" # ddc probing of monitor
Load "dbe"
#Load "dri"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "type1"
Load "freetype"
Load "record"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" ""
Option "XkbVariant" ""
EndSection
Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection
Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection
Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection
# Auto-generated by Archie mkxcfg
Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "true"
# HorizSync 28.0 - 78.0 # Warning: This may fry very old Monitors
HorizSync 28.0 - 96.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 75.0 # Very conservative. May flicker.
# VertRefresh 50.0 - 62.0 # Extreme conservative. Will flicker. TFT default.
# Default modes distilled from
# "VESA and Industry Standards and Guide for Computer Display Monitor
# Timing", version 1.0, revision 0.8, adopted September 17, 1998.
# $XFree86: xc/programs/Xserver/hw/xfree86/etc/vesamodes,v 1.4 1999/11/18 16:52:17 tsi Exp $
EndSection
# Auto-generated by Archie mkxcfg
Section "Device"
Identifier "nVidia GeForce4 MX 440"
Driver "nvidia"
VendorName "All"
BoardName "All"
Option "NoLogo" "true"
Option "NvAGP" "1"
EndSection
Section "Screen"
Identifier "Screen0"
Device "nVidia GeForce4 MX 440"
Monitor "Monitor0"
DefaultColorDepth 24
Option "UseDisplayDevice" "DFP"
SubSection "Display"
Depth 8
Modes "1400x1050" "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1400x1050" "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1400x1050" "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
#Section "DRI"
# Mode 0666
#EndSection
Perhaps I've overlooked something?
I then proceeded to scour through my X log files and notice some warnings, but no errors:
X Window System Version 7.2.0
Release Date: 22 January 2007
X Protocol Version 11, Revision 0, Release 7.2
Build Operating System: UNKNOWN
Current Operating System: Linux dead_meadow 2.6.23-ARCH #1 SMP PREEMPT Fri Oct 19 08:48:54 UTC 2007 i686
Build Date: 08 April 2007
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Oct 22 19:10:42 2007
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Xorg Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "nVidia GeForce4 MX 440"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbRules" "xorg"
(**) XKB: rules: "xorg"
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(WW) Option "XkbLayout" requires an string value
(WW) Option "XkbVariant" requires an string value
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "PS/2 Mouse"
(WW) The directory "/usr/share/fonts/PEX" does not exist.
Entry deleted from font path.
(WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/cyrillic".
Entry deleted from font path.
(Run 'mkfontdir' on "/usr/share/fonts/cyrillic").
(WW) The directory "/usr/share/fonts/ttf/western" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/ttf/decoratives" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/truetype" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/truetype/openoffice" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/truetype/ttf-bitstream-vera" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/latex-ttf-fonts" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/defoma/CID" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/defoma/TrueType" does not exist.
Entry deleted from font path.
(**) FontPath set to:
/usr/share/fonts/misc:unscaled,
/usr/share/fonts/misc,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/75dpi,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/100dpi,
/usr/share/fonts/Type1
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(**) Option "AllowMouseOpenFail" "true"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81c44a0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 1.1
X.Org XInput driver : 0.7
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(++) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 10de,01e0 card 0000,0000 rev a2 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 10de,01eb card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:2: chip 10de,01ee card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:3: chip 10de,01ed card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:4: chip 10de,01ec card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:00:5: chip 10de,01ef card 1509,904d rev a2 class 05,00,00 hdr 80
(II) PCI: 00:01:0: chip 10de,0060 card 1509,904d rev a4 class 06,01,00 hdr 80
(II) PCI: 00:01:1: chip 10de,0064 card 1509,904d rev a2 class 0c,05,00 hdr 80
(II) PCI: 00:02:0: chip 10de,0067 card 1509,904d rev a4 class 0c,03,10 hdr 80
(II) PCI: 00:02:1: chip 10de,0067 card 1509,904d rev a4 class 0c,03,10 hdr 80
(II) PCI: 00:02:2: chip 10de,0068 card 1509,904d rev a4 class 0c,03,20 hdr 80
(II) PCI: 00:04:0: chip 10de,0066 card 1509,904d rev a1 class 02,00,00 hdr 00
(II) PCI: 00:05:0: chip 10de,006b card 1509,904d rev a2 class 04,01,00 hdr 00
(II) PCI: 00:06:0: chip 10de,006a card 1509,904d rev a1 class 04,01,00 hdr 00
(II) PCI: 00:08:0: chip 10de,006c card 0000,0000 rev a3 class 06,04,00 hdr 01
(II) PCI: 00:09:0: chip 10de,0065 card f509,904d rev a2 class 01,01,8a hdr 00
(II) PCI: 00:1e:0: chip 10de,01e8 card 0000,0000 rev a2 class 06,04,00 hdr 01
(II) PCI: 01:06:0: chip 11ab,1faa card 1385,6b00 rev 03 class 02,00,00 hdr 00
(II) PCI: 01:08:0: chip 14f1,2f20 card 14f1,2000 rev 00 class 07,80,00 hdr 00
(II) PCI: 03:00:0: chip 10de,01f0 card 0000,0000 rev a3 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,3), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:1:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:8:0), (0,1,1), BCTRL: 0x0002 (VGA_EN is cleared)
(II) Bus 1 I/O range:
[0] -1 0 0x00009000 - 0x00009fff (0x1000) IX[b]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xed000000 - 0xedffffff (0x1000000) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 3: bridge is at (0:30:0), (0,3,3), BCTRL: 0x000a (VGA_EN is set)
(II) Bus 3 non-prefetchable memory range:
[0] -1 0 0xeb000000 - 0xecffffff (0x2000000) MX[b]
(II) Bus 3 prefetchable memory range:
[0] -1 0 0xe0000000 - 0xe7ffffff (0x8000000) MX[b]
(--) PCI:*(3:0:0) nVidia Corporation NV18 [GeForce4 MX - nForce GPU] rev 163, Mem @ 0xeb000000/24, 0xe0000000/26, 0xe4000000/19
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) PCI Memory resource overlap reduced 0xe8000000 from 0xe9ffffff to 0xe7ffffff
(II) Active PCI resource ranges:
[0] -1 0 0xed020000 - 0xed02ffff (0x10000) MX[b]
[1] -1 0 0xed010000 - 0xed01ffff (0x10000) MX[b]
[2] -1 0 0xed000000 - 0xed00ffff (0x10000) MX[b]
[3] -1 0 0xee080000 - 0xee080fff (0x1000) MX[b]
[4] -1 0 0xee000000 - 0xee07ffff (0x80000) MX[b]
[5] -1 0 0xee084000 - 0xee084fff (0x1000) MX[b]
[6] -1 0 0xee083000 - 0xee0830ff (0x100) MX[b]
[7] -1 0 0xee082000 - 0xee082fff (0x1000) MX[b]
[8] -1 0 0xee085000 - 0xee085fff (0x1000) MX[b]
[9] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[b]O
[10] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[b](B)
[11] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b](B)
[12] -1 0 0xeb000000 - 0xebffffff (0x1000000) MX[b](B)
[13] -1 0 0x00009000 - 0x00009007 (0x8) IX[b]
[14] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[b]
[15] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[16] -1 0 0x0000b000 - 0x0000b0ff (0x100) IX[b]
[17] -1 0 0x0000c400 - 0x0000c407 (0x8) IX[b]
[18] -1 0 0x0000c000 - 0x0000c01f (0x20) IX[b]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xed020000 - 0xed02ffff (0x10000) MX[b]
[1] -1 0 0xed010000 - 0xed01ffff (0x10000) MX[b]
[2] -1 0 0xed000000 - 0xed00ffff (0x10000) MX[b]
[3] -1 0 0xee080000 - 0xee080fff (0x1000) MX[b]
[4] -1 0 0xee000000 - 0xee07ffff (0x80000) MX[b]
[5] -1 0 0xee084000 - 0xee084fff (0x1000) MX[b]
[6] -1 0 0xee083000 - 0xee0830ff (0x100) MX[b]
[7] -1 0 0xee082000 - 0xee082fff (0x1000) MX[b]
[8] -1 0 0xee085000 - 0xee085fff (0x1000) MX[b]
[9] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[b]O
[10] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[b](B)
[11] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b](B)
[12] -1 0 0xeb000000 - 0xebffffff (0x1000000) MX[b](B)
[13] -1 0 0x00009000 - 0x00009007 (0x8) IX[b]
[14] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[b]
[15] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[16] -1 0 0x0000b000 - 0x0000b0ff (0x100) IX[b]
[17] -1 0 0x0000c400 - 0x0000c407 (0x8) IX[b]
[18] -1 0 0x0000c000 - 0x0000c01f (0x20) IX[b]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xed020000 - 0xed02ffff (0x10000) MX[b]
[5] -1 0 0xed010000 - 0xed01ffff (0x10000) MX[b]
[6] -1 0 0xed000000 - 0xed00ffff (0x10000) MX[b]
[7] -1 0 0xee080000 - 0xee080fff (0x1000) MX[b]
[8] -1 0 0xee000000 - 0xee07ffff (0x80000) MX[b]
[9] -1 0 0xee084000 - 0xee084fff (0x1000) MX[b]
[10] -1 0 0xee083000 - 0xee0830ff (0x100) MX[b]
[11] -1 0 0xee082000 - 0xee082fff (0x1000) MX[b]
[12] -1 0 0xee085000 - 0xee085fff (0x1000) MX[b]
[13] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[b]O
[14] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[b](B)
[15] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b](B)
[16] -1 0 0xeb000000 - 0xebffffff (0x1000000) MX[b](B)
[17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[18] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[19] -1 0 0x00009000 - 0x00009007 (0x8) IX[b]
[20] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[b]
[21] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[22] -1 0 0x0000b000 - 0x0000b0ff (0x100) IX[b]
[23] -1 0 0x0000c400 - 0x0000c407 (0x8) IX[b]
[24] -1 0 0x0000c000 - 0x0000c01f (0x20) IX[b]
(II) LoadModule: "ddc"
(II) Loading /usr/lib/xorg/modules//libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.1
(II) NVIDIA GLX Module 96.43.01 Wed Sep 5 19:47:01 PDT 2007
(II) Loading extension GLX
(II) LoadModule: "type1"
(II) Loading /usr/lib/xorg/modules/fonts//libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 7.2.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) LoadModule: "keyboard"
(II) Loading /usr/lib/xorg/modules/input//keyboard_drv.so
(II) Module keyboard: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.1.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) NVIDIA dlloader X Driver 96.43.01 Wed Sep 5 19:14:11 PDT 2007
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 03:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset NVIDIA GPU found
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/lib/xorg/modules//libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 1.1
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xed020000 - 0xed02ffff (0x10000) MX[b]
[5] -1 0 0xed010000 - 0xed01ffff (0x10000) MX[b]
[6] -1 0 0xed000000 - 0xed00ffff (0x10000) MX[b]
[7] -1 0 0xee080000 - 0xee080fff (0x1000) MX[b]
[8] -1 0 0xee000000 - 0xee07ffff (0x80000) MX[b]
[9] -1 0 0xee084000 - 0xee084fff (0x1000) MX[b]
[10] -1 0 0xee083000 - 0xee0830ff (0x100) MX[b]
[11] -1 0 0xee082000 - 0xee082fff (0x1000) MX[b]
[12] -1 0 0xee085000 - 0xee085fff (0x1000) MX[b]
[13] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[b]O
[14] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[b](B)
[15] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b](B)
[16] -1 0 0xeb000000 - 0xebffffff (0x1000000) MX[b](B)
[17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[18] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[19] -1 0 0x00009000 - 0x00009007 (0x8) IX[b]
[20] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[b]
[21] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[22] -1 0 0x0000b000 - 0x0000b0ff (0x100) IX[b]
[23] -1 0 0x0000c400 - 0x0000c407 (0x8) IX[b]
[24] -1 0 0x0000c000 - 0x0000c01f (0x20) IX[b]
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xed020000 - 0xed02ffff (0x10000) MX[b]
[5] -1 0 0xed010000 - 0xed01ffff (0x10000) MX[b]
[6] -1 0 0xed000000 - 0xed00ffff (0x10000) MX[b]
[7] -1 0 0xee080000 - 0xee080fff (0x1000) MX[b]
[8] -1 0 0xee000000 - 0xee07ffff (0x80000) MX[b]
[9] -1 0 0xee084000 - 0xee084fff (0x1000) MX[b]
[10] -1 0 0xee083000 - 0xee0830ff (0x100) MX[b]
[11] -1 0 0xee082000 - 0xee082fff (0x1000) MX[b]
[12] -1 0 0xee085000 - 0xee085fff (0x1000) MX[b]
[13] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[b]O
[14] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[b](B)
[15] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b](B)
[16] -1 0 0xeb000000 - 0xebffffff (0x1000000) MX[b](B)
[17] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[18] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[19] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[22] -1 0 0x00009000 - 0x00009007 (0x8) IX[b]
[23] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[b]
[24] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[25] -1 0 0x0000b000 - 0x0000b0ff (0x100) IX[b]
[26] -1 0 0x0000c400 - 0x0000c407 (0x8) IX[b]
[27] -1 0 0x0000c000 - 0x0000c01f (0x20) IX[b]
[28] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[29] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "NoLogo" "true"
(**) NVIDIA(0): Option "NvAGP" "1"
(**) NVIDIA(0): Option "UseDisplayDevice" "DFP"
(**) NVIDIA(0): Enabling RENDER acceleration
(**) NVIDIA(0): Use of NVIDIA internal AGP requested
(II) NVIDIA(0): NVIDIA GPU GeForce4 MX Integrated GPU at PCI:3:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 65536 kBytes
(--) NVIDIA(0): VideoBIOS: 04.1f.00.08.09
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce4 MX Integrated GPU at
(--) NVIDIA(0): PCI:3:0:0:
(--) NVIDIA(0): Acer X191W (CRT-0)
(--) NVIDIA(0): Acer X191W (CRT-0): 300.0 MHz maximum pixel clock
(WW) NVIDIA(0): Option "UseDisplayDevice" requested "DFP", but no unused DFPs
(WW) NVIDIA(0): are available.
(II) NVIDIA(0): Option "UseDisplayDevice" "DFP" converted to "".
(WW) NVIDIA(0): Unable to find any of the requested display device "" in the
(WW) NVIDIA(0): list of available display devices "CRT-0".
(II) NVIDIA(0): Assigned Display Device: CRT-0
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "1400x1050"
(II) NVIDIA(0): "1280x1024"
(II) NVIDIA(0): "1024x768"
(II) NVIDIA(0): "800x600"
(II) NVIDIA(0): "640x480"
(II) NVIDIA(0): Virtual screen size determined to be 1400 x 1050
(WW) NVIDIA(0): Insufficient memory bandwidth for MetaMode "800x512";
(WW) NVIDIA(0): discarding.
(WW) NVIDIA(0): No valid modes for "800x512"; removing.
(--) NVIDIA(0): DPI set to (93, 88); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xe4000000 - 0xe407ffff (0x80000) MX[b]
[1] 0 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b]
[2] 0 0 0xeb000000 - 0xebffffff (0x1000000) MX[b]
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[7] -1 0 0xed020000 - 0xed02ffff (0x10000) MX[b]
[8] -1 0 0xed010000 - 0xed01ffff (0x10000) MX[b]
[9] -1 0 0xed000000 - 0xed00ffff (0x10000) MX[b]
[10] -1 0 0xee080000 - 0xee080fff (0x1000) MX[b]
[11] -1 0 0xee000000 - 0xee07ffff (0x80000) MX[b]
[12] -1 0 0xee084000 - 0xee084fff (0x1000) MX[b]
[13] -1 0 0xee083000 - 0xee0830ff (0x100) MX[b]
[14] -1 0 0xee082000 - 0xee082fff (0x1000) MX[b]
[15] -1 0 0xee085000 - 0xee085fff (0x1000) MX[b]
[16] -1 0 0xe8000000 - 0xe7ffffff (0x0) MX[b]O
[17] -1 0 0xe4000000 - 0xe407ffff (0x80000) MX[b](B)
[18] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[b](B)
[19] -1 0 0xeb000000 - 0xebffffff (0x1000000) MX[b](B)
[20] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprD)
[21] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprD)
[22] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprD)
[23] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[24] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[25] -1 0 0x00009000 - 0x00009007 (0x8) IX[b]
[26] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[b]
[27] -1 0 0x0000b400 - 0x0000b47f (0x80) IX[b]
[28] -1 0 0x0000b000 - 0x0000b0ff (0x100) IX[b]
[29] -1 0 0x0000c400 - 0x0000c407 (0x8) IX[b]
[30] -1 0 0x0000c000 - 0x0000c01f (0x20) IX[b]
[31] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[32] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) NVIDIA(0): Setting mode "1400x1050"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(**) Option "dpms" "true"
(**) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(WW) Option "XkbLayout" requires an string value
(WW) Option "XkbVariant" requires an string value
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "auto"
(**) PS/2 Mouse: Device: "/dev/psaux"
(**) PS/2 Mouse: Protocol: "auto"
(**) Option "SendCoreEvents" "true"
(**) PS/2 Mouse: always reports core events
(**) Option "CorePointer"
(**) PS/2 Mouse: Core Pointer
(**) Option "Device" "/dev/psaux"
(**) Option "Emulate3Buttons" "true"
(**) Option "Emulate3Timeout" "70"
(**) PS/2 Mouse: Emulate3Buttons, Emulate3Timeout: 70
(**) Option "ZAxisMapping" "4 5"
(**) PS/2 Mouse: ZAxisMapping: buttons 4 and 5
(**) PS/2 Mouse: Buttons: 9
(II) XINPUT: Adding extended input device "PS/2 Mouse" (type: MOUSE)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(--) PS/2 Mouse: PnP-detected protocol: "ExplorerPS/2"
(II) PS/2 Mouse: ps2EnableDataReporting: succeeded
Perhaps the warnings pertaining to my monitor and ACPI are pertinent?
Is it possible that there is some kind of issue with my configuration and OpenGL textures since I can still see some non-textured 3D objects? Any help would be greatly appreciated, I am beyond frustrated with the matter. On a sidenote, in my latest issue of Linux Pro Magazine, I booted up a Sabayon live disc that game with the magazine and I had the same error except that a message blatantly said that I did not have OpenGL support. Anyway, I apologized if I rambled a bit and I hope that we'll be able to find a solution. Cheers!

I guess I forgot to disclose that bit, haha. I'm currently using the 'nvidia-96xx' drivers which I thought were the correct set for the GeForce4 series. I recall reading that in a wiki somewhere, but I could be mistaken. I thought 'nvidia-71xx' was for GeForce2 and earlier.I really hope it is as simple as me installing the wrong driver.

When sending email I get this error message: An error occurred sending mail: The mail server sent an incorrect greeting: Cannot establish SSL with SMTP server

This issue has popped up before then went away after I switched to SSL setings as suggested by my website host. Or...was it pure coincidence? Same problem today and I haven't made any changes since the above mentioned and have had many successful emails sent. Can't reply or send emails and the draft gets removed from the draft folder even if I saved it before hitting send. Thank you!

Thank you Matt. I'm sure this will be frustrating ...but the more I think about this problem there more info I have to share. The emails I write that do not get sent do end up in my "sent" folder but never reach the recipient. And, most perplexing, the issue/problem is sporadic. It was coming and going before I switched over to the SSL/TLS option in T-bird. And...since the switch it has reappeared and disappeared. I have made zero changes other than the above mentioned. I did get a security update today for T-bird perhaps this will help?
I read your link, thank you.
I obviously don't understand how these systems work. I'm baffled how an issue like this can come and go...

Are there any recommended group policies to consider for users consuming SharePoint?

Hi - we are close to going live with a new SharePoint 2013 farm and the question of GPOs has come up. Havn't seen any best practice or recommendations about this so was wondering if anyone in the community has any views?
Cheers
J

The major group policy settings that you should engage with your NOS managers involve security settings: service account security settings, network storage security settings and local security settings. if you do not build your knowledge of these interactions,
you may encounter highly arcane and deeply perplexing performance issues and even failures that appear to have no immediate cause that you can quickly point to and resolve.
Service Account Security Settings
All service accounts used in your farm should be domain service accounts.
Some of these accounts must have read permission to read the properties of all other service accounts. Such accounts include: farm service account, user profile service account, SQL server agent account (the account you assign to run your SQL server),
and the workflow manager 1.0 service account.
For example, if you will be creating SQL Server backup maintenance plans, you must give the the SQL Server service account the permission to read the domain account that you logged in as to create these maintenance plans. I discuss this more
here.
Network Storage Security Settings
The search service account needs RW permission to the network folder you use to store farm backups (the backups created either through CA or via PowerShell). If it does not have this, a backup performed through CA or via PowerShell will succeed in
everything except the Search portion. This was not the case for 2010. Why the search service account now needs to touch a backup folder is completely beyond me. But there you have it. I discuss this more
here.
Local Security Policy
The Search Service accounts must have these local security policy user rights assignments or your search service performance will deteriorate markedly: Adjust memory quotas for a process, Impersonate a client after authentication and Replace a process
level token.
Likewise, be sure to assign these user rights assignments to the farm service account: Allow log on locally, Adjust memory quotas for a process, Impersonate a client after authentication, Log on as a batch job, Log on as a service and Replace a
process level token.
More of these assignments are discussed
here.
Your GPO is likely pushed out on a regular basis (eg, every half hour), so, it may overwrite any settings changes implemented by an installer or configuration wizard. Not configuring these settings correctly can lead to highly arcane and perplexing
problems, manifested in error messages that do not provide real troubleshooting assistance. The problem is that Microsoft has not documented these various security settings needed by SharePoint service accounts and processes down to the level discussed
here and as noted above. This is also one of the reasons I believe why Microsoft strongly recommends that you perform all installation and subsequent configuration using the SharePoint Setup User Administrator account (eg, spAdmin): this account
is used to configure a wide variety of registry entries and folders and is granted the permission to edit these as necessary. Your administrator account may not be.
Another area for GPO attention involves firewalls. For example, you need to make sure that the Windows Firewall on your SQL Server instance(s) has appropriate rules configured to allow inbound and outbound traffic.
References
Plan for administrative and service accounts in SharePoint 2013
Account permissions and security settings in SharePoint 2013
SharePoint 2013: Service Account Configurations and Permissions
SQL Server 2012: SQLServer Error: 15404 Could not obtain information about Windows NT group/user
SharePoint 2013: FatalError: Object Search Service failed in event OnBackup
SharePoint 2013: cannot connect to database at SQL server at... The database might not exist...

When sending an email through windows live I get an error message from WebKit2WebProcess.exe

Hi,
Every time when I try and send an email from windows live I get an error message from WebKit2WebProcess.exe.
Not sure if I deactivate this from Windows live whether I will compromise my security.
Any advice would be helpful.
Thanks,
Becky

Thank you Matt. I'm sure this will be frustrating ...but the more I think about this problem there more info I have to share. The emails I write that do not get sent do end up in my "sent" folder but never reach the recipient. And, most perplexing, the issue/problem is sporadic. It was coming and going before I switched over to the SSL/TLS option in T-bird. And...since the switch it has reappeared and disappeared. I have made zero changes other than the above mentioned. I did get a security update today for T-bird perhaps this will help?
I read your link, thank you.
I obviously don't understand how these systems work. I'm baffled how an issue like this can come and go...

Too many decimals

Hi all,
I am on 3.5 and have a perplexing BEx issue. I have a calculation I wnat to restrict to format '0.000' (three decimals). I formated it that way in the forumla, but when it is calculated in the BEx, it has many more decimals. What I am doing (in one example) is multiplying 11 * .16 * 8. This yields 14.08. Then I am taking that 14.08, and dividing it by 1728, which yields .00814814. This appears on the report as '0.008', which is what I want, but when I do additional calculations on it, it retains the other decimals, which is messing other calculations based on this number.
Is there any way to do this with a formula - force it to three decimals? Could I use a calc KF? Help!
Thanks.
Dave

Hi David,
You can do that using normalization for the Key figure properties.
There are some posts here which discuss the same problem:
Decimals number when using 'Calculate values as... normalize result'
Re: Decimals problem in report
Re: Normalization function & number of decimals
Bye
Dinesh

External firewire drive fails to boot OS X after restart

I have a G4 Cube that exhibits a perplexing boot issue on an external firewire drive. The external drive is a clone of the Cube's internal dual boot, two partition drive made with an identical 120 GB Seagate. The internal drive boots without incident into either OS X or OS 9 - each in it's own partition.
The problem comes when I select the external drive's OS X partition in Startup Disk and restart - the external drive's activity LED shows an initial attempt to boot but then hesitates and boots to the internal OS X partition repeatedly.
As a workaround, I am able to select and boot to the OS 9 partition, either internally or externally, launch the StartUp Disk control panel, select the external OS X partition and reboot successfully into that partition. But upon a restart, it fails to boot into the external OS X partition repeating the aforementioned behavior i.e. it boots to the internal OS X partition.
Using Option-Restart shows the the two partitions on the external drive and the two partitions on the internal drive normally but will only successfully process selecting either of the two OS 9 partitions or the internal OS X partition, again failing to process a selection to the external OS X partition.
Interestingly, this same external firewire drive will repeatedly boot to it's OS X partition without incident using either of two iBook G4s.
I'm stumped!

Hi, LEOinDC -
How old is the internal battery in that Cube? Many machines exhibit boot anomalies if that battery is too weak or dead.
Those batteries have an expected life of about 4 to 5 years under best-case usage; if the machine is unplugged regularly or for an extended period, the battery is consumed much faster. Even if the machine is not unnplugged the battery will eventually die, and there will be no symptoms such as loss of date or time since the trickle power drawn when the machine is shut down (but still plugged in) will maintain those.
Also, is the external firewire drive self-powered? If not, try that.
Sometimes when using Startup Manager (which is what booting with Option held down invokes), all available bootable volumes aren't picked up before it displays what it has found. The solution for that is to click the circular arrow button in Startup Manager - this is an instruction to rescan the buses.

Pre Order Issue Madden 15 - no preorder bonus

I did not receive the pre order bonus for madden 15. What are my options when the CS rep messed up the transaction. I picked up the game instore (4hrs ago) and the bonus did not show up on the recepit and i have not recieved an email. I originally told the rep that it did not look right. I am a member of the gamers unlocked, so i am not sure if they assumed that the 20% off was part of the $5 deposit. I also used the promo coupon for $10 off madden. I just check my receipt and the $5 deposit was not taken off the price of the game. I have a feeling i just bought the game and not pick up my pre order. What should I do to correct this issue? Will I loose all the preorder bonuses? This is the second time I did an instore preorderd. The first time i had to return/rebuy. Will have have to do the same?

Hi akashmia,
While I’m very thankful that you pre-ordered your copy of Madden 15 from Best Buy, I certainly apologize as it sounds like it turned into quite the fiasco for you when picking up the game. The pre-order bonuses for Madden 15 were a great incentive and it’s understandable that you’d be nervous about losing them. I’d like to review the details of your transaction and see what occurred, as well as help you determine the best course of action here!
Using your email address on file for the forums, I’ve attempted to locate the purchase and haven’t been able to do so. With that said, at your earliest convenience, please send me a private message and include the Customer Service PIN located at the bottom of the final sales receipt. Once I receive this information, I’ll be able to review the details and assist further. To send me a private message, simply click the link in my signature.
I look forward to hearing from you!
Thanks,
Brian|Senior Social Media Specialist | Best Buy® Corporate
Private Message

I am trying to rent a movie on iTunes. It keeps telling me that I need to connect to wifi or download on a computer. I am connected. What is the issue? This is maddening!

I am trying to rent a movie on iTunes. It keeps telling me that I need to connect to wifi or download on a computer. I am connected. What is the issue? This is maddening!

If you are using a Windows based computer, try disabling anti virus software and turn off the Firewall.
iTunes for Windows: Troubleshooting security software issues
Then try downloading iTunes media.

Madden 15 Pre-order Issue

I preordered Madden 15 Ultimate Edition in-store and when picking up the game something got screwed up.
It was going fine until I handed the clerk the $10 off coupon, and I apparently gave it to her too late in the transaction even tho I hadn't paid yet. She told me that she would have to void the transaction and begin again and scan the coupon earlier. On the second try, since I had a $5 preorder deposit, she applied the $5 as a "discount". And here's where the problem is, as the system didn't recognize that I was actually picking up a preorder.
The bottom line is that I didn't get any preorder bonuses printed on the receipt and the 500 points for preordering the game are not pending on my account. Can somebody please help me with this?

Hi jdpantoja,
Thank you as well for pre-ordering Madden 15 at Best Buy. I hope you’ve been enjoying the Ultimate Edition thus far. I’m sorry to hear that you may have experienced in issue in regards to the Get $10 promotion. Since it sounds like you feel there may have been an issue with how the transaction, specifically with it not being recognized as a pre-order, I’d love to look into this more and see if I can assist!
Using your email address on file for the forums, I was able to locate your purchase receipt, as well as the initial pre-order receipt. In reviewing the details, I’m immediately able to recognize what happened here. I’m going to send you a private message with more information. To check your private messages, make sure you’re logged in to the forums and click the small envelope on the top right of the screen.
I’ll be reaching out to you shortly.
Thanks again!
Brian|Senior Social Media Specialist | Best Buy® Corporate
Private Message

Maddening perplexing HD issue!

Similar Messages

Maybe you are looking for