Mark debug 'sometimes' not working

I find mark debug sometimes not working.In my new project ,I add mark debug = true, then set up the debug nets.I can't find them in the assigned nets ,but from the netlists I find some of them.The missing nets are wire type,notregister type.Does the command not work on wire type nets?
Because my project is very large, searching for the nets requires a very long time.So I hope Xilinx can fix this bug.

Rather than open another thread, I'll extend this one since I'm having what I think is the same problem.
I'm using Vivado 2014.4. "Flatten" is set to "None". The nets are set in the elaborated design with MARK_DEBUG and DONT_TOUCH. But when synthesis gets done with them, the names are completely different.
I don't care if the "equivalent" nets are still there. I need the names. Every time synthesis runs, it's a crapshoot whether the names will change. Particularly bad are 500+ bit buses that get exploded into individual signals. I don't have the time to regather them into the proper buses every time.
In general, I've been pleased with the changes in Viviado. But I can't believe how badly a wonderful tool like ChipScope has been screwed up.

Similar Messages

Sometime not work = Word Substitution

10.2.0.415
BlackBerry 10 os
please help,
i use thats version at Q5 BB but i get orror at :
Prediction and Correction > Word Substitution >
I cannot use this service, sometimes ok/normal, sometimes not work, its very important to me,
Thats only my reson why i buy Q5 BB please Help,
i have much word to explain to my friend, and with that function will help me, and make my finger easy and very health.
Thank you very much

yoyongsc wrote:
Mine doesn't work in all applications, bbm, text, email, etc.
Verry odd! My Word Sub works well in all of those you've listed.
It does not work in commenting on BBM group pictures and in some BBM Channel comments... works every where else.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Debugging is not working in R/3 from WebDynpro-ABAP developed webpage input

Dear Friends,
We are facing a serious problem for debugging. Expecting valuable input for the same.
Debugging is not working in R/3 from WebDynpro-ABAP developed webpage input in Production Server.
The debugging (for WebDynpro-ABAP application) is working in Dev. Server for
1st ] Within R/3
Ex. debug for bapi within R/3. i.e. value enter as input in R/3 only.
2nd ] From webpage to R/3
Ex. Some input given on the internet web page developed through WebDynpro and external breakpoint set in R/3 it works. It directs to R/3 code through debugging.
In Prod. Server the 1st case above is working but the 2nd case is not working.
In Prod. Server the WebDynpro developed applications are running successfully through internet explorer webpage inputs. So running the application is not a problem in prod. Server but debugging of the same is the problem.
The setting which are done in Prod. server are,
1] RZ10 in parameters are set for port and host name.
2.1] In SMICM check for ICM.
2.2] Host file updated in Windows-System 32.
3] In SICF following services are active,
3.1] default_host/sap/bc/webdynpro
3.2] default_host/sap/public/bc
3.3] default_host/sap/public/bc/webdynpro/viewdesigner
3.4] default_host/sap/bc/wdvd
3.5] default_host/sap/public/icman
3.6] default_host/sap/bc/gui/sap/its/webgui
3.7] default_host/sap/public/ping
3.8] default_host/sap/bc/error
3.9] default_host/sap/bc/echo
4] In SE80
4.1] Internet services-System-are published
4.2] Internet services-WEBGUI-are published
4.3] Utilities-Setting-ABAP Editor-Debugging-Username & New Debugger set.
4.4] Utilities-Setting-ABAP Editor-Editor-Front-End Editor(New) set.
5] In Su01 for user profiles sap_all & sap_new is assigned and role SAP_BC_WEBSERVICE_DEBUGGER is assigned.
6] The support packages are also updated to latest level.
7] Gone through following links but not getting any clues.
http://help.sap.com/saphelp_nw70ehp1/helpdata/en/48/74d50bd1431b5ae10000000a42189c/frameset.htm
http://help.sap.com/saphelp_nw04s/helpdata/EN/77/3545415ea6f523e10000000a155106/frameset.htm
Thanks in Advance.
Best Regards,
Abhijit.

No cross posting
Read the "Rules of Engagament"
Regards
Juan

[LAVA Cross Post] CTRL+SHIFT+ Shortcuts sometimes not working in LabVIEW

Cross-post from LAVA: http://lavag.org/topic/15619-ctrlshift-shortcuts-sometimes-not-working-in-labview/
See the above post for more information - here's a synopsis:
CTRL+SHIFT modifiers are not working while running LabVIEW in a Parallels 7 virtual machine. This problem affects both LV2011 and LV2012. I'm not certain that this is a LabVIEW bug - could be an issue with my virtual machine environment or it's configuration - except that CTRL+SHIFT modifiers work in other applications on the affected VMs. It's just LabVIEW that appears to ignore shortcuts with the CTRL+SHIFT modifiers.
Any ideas?
a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"] {color: black;} a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"]:after {content: '';} .jrd-sig {height: 80px; overflow: visible;} .jrd-sig-deploy {float:left; opacity:0.2;} .jrd-sig-img {float:right; opacity:0.2;} .jrd-sig-img:hover {opacity:0.8;} .jrd-sig-deploy:hover {opacity:0.8;}

X. wrote:
Still well and alive in Parallels 9 and LabVIEW 2013 SP1. Of course I could upgrade to the latest versions to check whether things have gotten any better.
Any news on that?
@mellroth figured out the solution :-)
a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"] {color: black;} a.lia-user-name-link[href="/t5/user/viewprofilepage/user-id/88938"]:after {content: '';} .jrd-sig {height: 80px; overflow: visible;} .jrd-sig-deploy {float:left; opacity:0.2;} .jrd-sig-img {float:right; opacity:0.2;} .jrd-sig-img:hover {opacity:0.8;} .jrd-sig-deploy:hover {opacity:0.8;}

Book Mark Icon is not working?

Hi,
There is an Adhoc query created by the end user.The book mark icon available is not working but the CONTEXT MENU on any of the values is producing the book mark properly.Can just any one help me to find the solution of this?
Why BOOK MARK ICON is not working?
Please correct me if I am wrong.
Book mark is URL we are getting after the clcking on the EIther on the ICON or context menu option.This URL can be used any where where ever is required.Right?
But In my case the URL Content is chainging based on the Adhoc query designer.Only characterstics are again and again changing but key figures are original only.
please help me?

U mean to say the Book Mark URL created on one system will not work on another system right?
=>the Book Mark URL created on one system may not work on another system right? in fact in 80% cases it works...
But what once I execute the query in portal I will be getting an URL.This also can be used as Book mark right?
=>yes, it can be used,,,
but the URL generated with the function of the BOOK MARK is only called as Book mark why is it?
=> let me explain this with an example ... there is a BW server physically located in France and can be accessible across all the location wherever project is running. Somebody try to access the Query URL from Gurgaon (one of the project location)which was executed in France may not be run in Gurgaon (Page cant be displayed) because port # in the URL may be blocked in Gurgaon due to security reason,,, this case we have to contact the admin ,they will enable the port..same case i have faced

Book mark Icon is not working in Adhco queries?

Hi,
There is an Adhoc query created by the end user.The book mark icon available is not working but the CONTEXT MENU on any of the values is producing the book mark properly.Can just any one help me to find the solution of this?
Why BOOK MARK ICON is not working?

Hi,
I observed the same, Book Mark Button availabe on web report is not working but Book mark URL can be saved with the context menu -> bookmark.
need to check the Web template for Book Mark.
Bookmark URL can be saved and that URL is used to go fastly to the requied navigation fastly, that is the use of Bookmark
hope this helps
Regards
Daya Sagar

SCCM 2012: F8 debug widow not working (At-least not visible) after entering into the "Currently installed Windows 7 Image": F8 works in winPE

F8 debug widow not working (At-least not visible) after entering into the "Currently installed Windows 7 Image"
F8 option turned on in the boot image.
F8 debug window works in Windows PE.
F8 debug window does not show-up on F8 key-press after entering the 'Currently installed Windows 7 Image" all the way to the end of the task sequence.
But after a 'Restart Step' (and if F8 was pressed) the Task Sequence tends to pause indefinitely as if the
F8 debug screen is open in the background.
I am using SCCM 2012 SP1 (CU 1 is
not an option at the moment).
Any ideas as to how I could get the debug F8 option back?

There have been a couple reported occurrences of this (or something similar) to my knowledge with no resolution in the forums. Your best bet may be to open a case with CSS.
Also note that if you were going to do a CU, why would you pick CU1 instead of CU4? And, can I ask why it's not an option out of curiosity?
Jason | http://blog.configmgrftw.com

Equium L40-156 - Indicator WLAN sometimes not work

Hello peoples - has anyone any idea wha this is bout?
I cant seem to find a similar problem anywhere. The indicator light for the wireless connection will sometimes not work - as a result i have to manually go into network connection and turn on wireless cap. - this will not turn the light on but does allow me to access the internet.
This happens for a few weeks and then it all rights itself for a few weeks,
Then it happens again.

Hi
Do you mean this issue happens sometimes but in most cases you can enable the WLan properly?
First of all to enable the WLan you have to move the WLan antenna switch to ON (be sure that it has been switched properly to the right) and you have I use the FN+F8 key combination.
Usually this enables the WLan.
Im not sure why the WLan antenna switch does not work sometimes maybe its a hardware issue; for example loose connection or the switch was not moved properly who knows
Maybe it would be a good idea to ask an technician for a WLan switch check...

Uploading Files Using InputFile Component -- Sometimes not working

Hello,
This is the 2nd time I make a post about it!
Because I have more than 1 application using upload, and everything is correct! But it doesn't work as it should!
You can check the original post here: Uploading Files Using InputFile Component - Sometimes not working
I need a solution please!
The only thing we can conclude is that it could be a bug from oracle !!! (???) But I talked with other people and they say that it works fine for them.
There is one important thing: when we put a form to "Uses Upload = true" it seems that the page doesn't work very normal. For exemple: if you use a table in a form that uses upload the table get's "crazy".
Thanks,
JP

I have now access to METALINK!
I can find some problems and patches about inputFile but not mine! I will check better later!
I think the problem is caused because of my framework!

Layout adjustment sometimes not working

I'm in a bit of a panic here. We've set up a file that we're due to deliver to a client today, the file has multiple master pages with various margins.
Normally in this type of situation we turn on the layout adjustment so that the text frame moves with the margins when the new master is applied. Normally this works just fine, we use it all the time, but for some reason its randomly NOT working! i.e. the text frame stays the size it was.
There doesn't seem to be any ryme or reason to it, sometimes its a left page, sometimes a right page.
Any ideas?
Thanks,
Ken

Yeah, I tried. Nothing seems to work all the time as is usually does.
I'll have to look again and see if I can find some correlation with the
pages that do not adjust.
Oy!
Thanks again

A problem with a timer event sometimes not working

Guys...
I have this problem:
I have a child added to the stage eacg 5 seconds and if this child still on the stage after another 5 seconds, you go to the next frame...
My problem is that sometimes it does not work, meaning that you can have this child on the stage for ever and nothing will happen... but sometimes it does work properlly...
Is there any mistakes in my code or what should I do?
var miC4:Loader = new Loader();
miC4.load(new URLRequest("nivel1.jpg"));
addChild(background1);
background1.addChild(miC4);
if (!lives){var lives:int = 3;}
var enem1:Loader = new Loader();
enem1.load(new URLRequest("1enemigo.png"));
var enemy1Array:Array = new Array(enem1);
var t1:Timer=new Timer(5000,1);
var t2:Timer=new Timer(10500,1);
recycleEnemy();
function removeEnemy(){
           background1.removeChild(enem1);
           recycleEnemy();
function touchListener(event:MouseEvent){
    enem1.removeEventListener(MouseEvent.CLICK, touchListener);
    removeEnemy();
function recycleEnemy():void{
        enem1.x=(50 + Math.random() * (stage.stageWidth - 150));
        enem1.y=(50 + Math.random() * (stage.stageHeight + -100));
        t1.addEventListener(TimerEvent.TIMER, addEnemy);
        t1.start();
        t2.addEventListener(TimerEvent.TIMER, bang1);
        t2.start();
function addEnemy(e:TimerEvent):void {
        background1.addChild(enem1);
        enem1.addEventListener(MouseEvent.CLICK, touchListener);
        enemy1Array.push(enem1);
function bang1(e:TimerEvent):void {
    if(enem1.stage){
                lives--;
                if (lives >= 0) {
                    t1.stop();
                    t2.stop();
                    removeChild(background1);
                    gotoAndStop(5);
Thanks a lot!!!!

ok, so there are a number of issues.
the first error is enemy1Array contains two duplicate objects ~5 seconds after entering that frame. i'm not sure if that's a problem because i don't see where you're even using enemy1Array, but you should fix that error (if enemy1Array is used) or remove enemy1Array (if it's not used).
the next problem is you can call recycleEnemy more than once and re-add those timers. flash will probably protect yourself from the bad coding but you shouldn't count on it. when you call removeEnemy you should stop those timers and remove those listeners before re-adding another pair of listeners. or just reset the timers in removeEnemy and start them in recycleEnemy. there's no need to re-add those listeners more than once. they could be added in your if(!lives) conditional.
the next (and probably most important) error is your removeChild(background1) statement which fails to remove enem1. so, when you re-enter that frame you have an enem1 on-stage that you can't kill and can't even reference. remove it when you remove the background1.

Using parameters in a select query sometimes not working

I use parameters throughout my code - usually without problem, but for some reason in one case it does not return a result. When I modify the querystring to contain the value instead of using parameters it works. Is it because I'm secting a clob? or is it because I'm using a 9i ODP.net dll against a 10g database? this is c# 2.0
here's the source code that does not work for me - REQUEST_DATA is a clob:
    public String loadRequest(String PSRNumber)
        String returnVal = null;
        ConnectionStringSettings connectionInfo = System.Configuration.ConfigurationManager.ConnectionStrings["Scribe"];
        OracleConnection myConnection = new OracleConnection();
        String strSQL = "select PSR, REQUEST_DATA from stats.request where PSR = :PSR";
        try
            myConnection.ConnectionString = connectionInfo.ConnectionString;
            OracleCommand cmd = new OracleCommand(strSQL, myConnection);
            cmd.CommandType = CommandType.Text;
            cmd.Parameters.Add("PSR", OracleDbType.Varchar2).Value = PSRNumber;
            myConnection.Open();
            OracleDataReader dr = cmd.ExecuteReader();
            if (dr.Read())
                returnVal = dr.GetOracleString(dr.GetOrdinal("REQUEST_DATA")).ToString();
            else
                returnVal = null;
            dr.Dispose();
            cmd.Dispose();
        catch (OracleException ex)
            printError(ex.Message);
        finally
            myConnection.Close();
            myConnection.Dispose();
        return returnVal;
    }when I replace the line generating the sql, and remove the lines pertaining to parameters it works:
String strSQL = String.Format("select PSR, REQUEST_DATA from stats.request where PSR = {0}", PSRNumber);
I'm fine just using this as a workaround, but I need an explanation why the other does not work - I prefer to use parameters.
Message was edited by:
user633546

I figured it out. thank you for your help in pointing me in the right direction.
the problem was there was a trailing space in the data.
when the data for that table is numeric for every record, the query allows me to leave out the single quotes. Trailing spaces do not seem to cause the database to see it as non-numeric - leaving out the quote still finds the record even if there is a trailing space.
but when I put in the quote, it is not an exact string match, so it could not find the record. sometimes this flexibility gets me into trouble :\

Update 8.1.2 iPhone 4 Problems. sometimes not working wifi or phone can't be swich on

i do not care about f....ringtones i need to use my phone! After Update 8.1.2 my phone is not working, got some Problems with wifi Connection sometimes the phone can't be swich on or Off. Its imposible to use my phone in the Right way. Whats up........?????

Which of the general trouble shooting measures have you tried already?
See the list here: iOS: Not responding or does not turn on - Apple Support
sometimes the phone can't be swich on or Off
Make a backup with iTunes, then restore the iPhone as a new device. Test if everything is working, then restore your data from the backup.

My Speakers sometimes not working

Hi, i purchased HPPavilion G6 laptop just 5-6 months back and since that time I am facing non-recurring problem with Audio whenever I use to play something online or using multimedia softwares. But I am unable to check reason for this as it's sometimes working perfectly and sometimes it doesn't and i usually restart and when relog-in it works!
Does anyone knows reason? As I have already checked it's drivers are working perfectly.

Hi Cancer1985,
I understand you are having issue with the speakers not working all the time. I was wondering if the next time it happens see if you can play music. Some sites do have issues with sound. If you have checked your drivers and all is well, I think it is with the sites. Here is a link on tips for fixing common sound problems.
http://windows.microsoft.com/en-ca/windows/tips-fixing-common-sound-problems#tips-fixing-common-soun...
Hope it helps.
Thanks
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Wireless sometimes not working after resume

After resuming from lid close hibernation wireless sometimes does not work.
Using Windows 7 64-bit
Intel 5100AGN driver 13.1.1.1
1. Have an active internet connection
2. Suspend closing the lid
3. Resume by opening the lid
4. Login
Result: Wireless has connection problems, cannot reconnect
Expected: Automatic fast reconnect
5. Deactivate the adapter and enable in again, or run troubleshooting which resets the adapter
6. Reconnect
How to fix that I have to reset the adapter or deactivate/enable it again?

right click my computer > manage > device management > network adapters > find your wireless adapter > double click > on power management tab, make sure "allow the computer to turn off this device to save power" unchecked

Mark debug 'sometimes' not working

Similar Messages

Maybe you are looking for