Monitor does not come on due to no input signal. Monitor is hp w2207. Hp media center pc m 260 N.

Desktop PC is connected correctly but monitor indicates no input signal & monitor goes to sleep mode. All my wireless laptops work ok. Does this have anything to do with wireless setup?

Although it appears the computer model name is incomplete, I assume you mean a HP Media Center m260n Desktop Computer. Here are the specs for your HP Pavilion w2207 LCD wide-screen flat panel monitor. The computer supports VGA only, unless you have previously installed an 8x AGP graphics card. The monitor supports both VGA and DVI-D.
The first step in troubleshooting this issue would be to connect the monitor to a known working computer using the same VGA cable. Does the monitor work??? Yes... could be the computer, No... could be the monitor or the cable. Next, connect the computer to another known working monitor with the same VGA cable. Does the monitor display a picture??? Yes, computer is good, No... computer or cable is bad. Post the results if you need more assistance.
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Similar Messages

Z87-G41 pc mate : monitor does not come back on after wakeup

Everytime the computer goes to sleep and wakes up, the monitor does not come on. I can shut it off and turn it back on and the desktop will flash, then goes black again. Just started doing this last week. I updated all drivers and this did not help either. I am running Win 7 Ultimate 32 bit. I have had this MOBO since last March with no problems. Any ideas?

>>Posting Guide<<
Possibly some updates or changes has been made?(within windows/bios)

After my computer hibernates the monitor does not come on

after my computer hibernates the monitor does not come on

Hi and thanks for joining HP Forums. Below are a couple of threads with multiple solutions to sleep/hibernate issues. Please read through these threads and see if any of these solutions will work to correct your problem. The mostly likely solutions such as allowing the video card to wake your computer and updating your drivers and BIOS are in the first link, but you may also find the solution in the second link.
http://social.technet.microsoft.com/Forums/en/w7itprohardware/thread/92e84b72-d2cc-4903-a564-c703565...
http://www.ehow.com/how_6815819_hp-won_t-recover-sleep-mode.html
Thanks!
I am an HP employee.
Please post rather than sending a Private Message. It's good for the community and I might not be able to get back quickly.- Thank you.
Please click the White Kudos star on the left to say thanks.
Please mark Accept As Solution if this resolves your issue.

Monitor does not come out of sleep Mac-Mini Mini-DVI to Dual DVI-D cable

I have an August 2009 Mac-Mini that I'm using with an Apple supplied Mini-DVI to DVI adapter along with a DVI-D Dual Link Cable connect to a Sceptre X7XV-Naga+ LCD monitor.
The monitor is going into sleep mode on its own with no way to disable this feature on the monitor itself. I've disabled sleep mode on the Mac-Mini in the power setting in System Preferences.
When in sleep mode and I move the mouse or press a key, the monitor will not come out of sleep mode. From other posts, I read that the issue might be that I wasn't using a Dual-Link DVI-D cable, so I bought one and installed such a cable. That has not resolved the problem. The monitor will not come out of sleep mode. When I have the monitor connected with a mini-display port to VGA adapter instead of a DVI-D cable, it will come out of sleep mode every time.
Message was edited by: Annorax64

I know it's a year later, but I'm not finding much through search.
I have the same exact problem. Difference being I'm using an iMac with 10.7.5.
Same video board and monitor - ATI Radeon HD 6750M video card connected via DisplayPort to Samsing S24A850DW.
I've tried two different mini-DisplayPort to DisplayPort cables and no change.
I think I read that 10.8.3 might fix the issue. Anyone that can confirm that, or has another solution?

How do I monitor a TCP/IP connection if my data does not come perdiodically?

I have an application that connects to several acquisition devices where I get TCP packet data only when something changes. If the line gets cut, how can I monitor this so that the user of the application will know that no data will come from that certain acquisition device? Since the data does not come periodically, I cannot monitor the error from the TCP read function, i.e. Error 56 - Timeout.
Is there a way to find out if an IP exists for example? (Such as a ping but it shoudl be fast)
Thanks

arikb-
You can use the System Exec.vi to run a ping command through the command line and see if it is responding. You could also program the client such that it responds to a simple command with a verification message at any time. This would be similar to sending a ping, but it will also let you know if your LabVIEW program is on the other listening on the correct port.
Xaq

Pc does not come out of sleep mode, no display on monitor, no response from mouse or keyboard.

Computer acts as though it is in sleep mode, does not respond to keyboard or mouse input. Confirmed monitor is OK. turning power on and of does not fix this issue. any ideas on how this migt be fixed?

The key issue is power. Please use this guide to test the PSU.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

MBP does not come back after hybernation

Hello everyone,
I am enjoying my MBP except for one problem. It does not come back after it hybernates sometimes.
I hit a key, hear the superdrive do it's "thing" and then after much waiting (approximately over 10 minutes) no picture or video on the screen!
I can tell that it's still powered on because it's plugged in and when I hit the Caps Lock key it lights on and off.
The only way that I can get it out of this state is to hold down the power button, unplug the power cord, take the battery out, hold in the power button for 4 seconds, reinsert the battery and power back on.
I have to then cycle the power back off because the first time it does not come back but I just get the blank white boot screen and no 'apple'.
When I turn it back on the second time, it boots up.
Anyone else have a problem with this?
Thanks for listening!
Mark

Hello Gweedo!
Yeah I have the same issue and am up to date. Apparently this is a pretty huge problem with the Macbook Pro since the last Graphics update after updating to 10.5.2.
http://discussions.apple.com/thread.jspa?threadID=1394449
I have been perusing through that topic and hopefully they will come up with a fix for this.
The only work-a-round that I have found (but haven't tested extensively yet) is to disconnect to the wireless, turn off blue tooth, disconnect my external monitor and then go into sleep mode. Then it always comes back. But if I leave it connected to the wireless, bluetooth, and external monitor - it's a crap shoot as to weather or not it will come back up.
This is pretty frustrating because half of using a laptop is being able to hybernate and sleep properly.
I even have the 'smartsleep' installed.
Thanks for commenting everybody!
Mark

When I close my laptop lid and it goes to sleep so that I can use an external monitor, monitor does not turn on when I hit a key to start laptop

When I use my external monitor, I cannot get it to work after awakening my laptop using any key. My monitor won't light up although laptop keyboard is backlit showing that it has come out of sleep mode. Why does the monitor not get the signal from the laptop?

I still cannot figure out why it doesn't always work. All parameters were met and my bluetooth keyboard is set correctly to wake the computer. My keyboard becomes backlit, but my LG monitor does not pick up a video signal and is black and my laptop monitor is off. The only way I can get out is to hold on button on laptop until it shuts down and I can start up again. This happens on an intermittent basis. Sometimes it works and other times I get black screens. I need to know if I can use command F1 to get the laptop to detect the display or is their another key combination to send the signal to the external monitor when I can't see anything because I hate to do a hard shut down to get out of this mode! Please advise!

2013 Mac Pro DisplayPort Monitor does not wake from Sleep.

On my 2013 MP I have dual monitors:
One connected DVI-to-MiniDisplayPort a ViewSonic 24"
Second connected DisplayPort-to-MiniDisplayPort a MonoPrice 27" 2560x1440
When the computer comes out of Sleep or Off the 27" display does not come out of Sleep Mode.
If I unplug and replug the MiniDisplayPort connection from the MP the Display will turn on correctly.
Never had this issue with the 24" both monitors go into a sleep/hibernate mode(yellow power light on displays) when the computer turns off or goes to sleep.
When the computer comes out of sleep the 27" backlight turns on briefly but then goes back into sleep mode.
Troubleshooting: PRAM Reset and alternative ports on the MacPro with no luck.
Any thoughts??
Thanks in advance.

Hello natemac00,
Thank you for using Apple Support Communities.
For more information, take a look at:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Have a nice day,
Mario

Macbook pro does not support Final Cut Pro preview on external monitor?

I have been editing on Final Cut Pro from my imac for approx 1 year with an external monitor attached with no problems. I recently bought a macbook pro, for Final Cut Pro editing, and discovered that the monitor does not work. The Final Cut Pro preview on the external monitor freezes and in the preview pane of FCP it flick between two images.
I have been reading around some forums, and have seen a couple of people with the same problem.
Anyone have a suggestion on how to run the external monitor with FCP?
Thanks!

You have probably already done it but ensure you have updated the OS and Quicktime prior to attempting to instal Final Cut Studio.
I recently had a hard drive crash and after installing the new hard drive it would not read the OS installation disc. I ended up using an external drive case and installed the OS on the drive from a different Mac Book, then reinstalled the hard drive in the other Mac Book. Then it booted right up. I updated all the original software before attempting to install any additional software.
Everyone kept saying it wouldn't install due a possibly defective optical drive and I can't say why but it wasn't the drive. As soon as I had the system up and running again the optical drive functioned flawlessly.
I hope this helps you.

Qosmio X500 - enternal monitor does not get a signal

Hi
its come a time when I need a external monitor to extend my desktop. I plugged in one of my monitors to the laptop. Qosmio sees it but the monitor does not get a signal. Tried a 2nd monitor and it does the same thing says cable not connected on 1 and power save on other.
I tested the monitors and cables on another laptop in the house and they work fine so its down to the laptop. Ive tried hdmi on a tv and that works fine, so seems to be just the vga as the laptop sees the monitor when connected does that mean the vga port is ok?
And could be something else? Any advice is welcome cheers.
John

Your posting is a bit confusing for me and I don't see clear structure there. What have you tested and the result is not clearly described.
>Ive tried hdmi on a tv and that works fine
How have you tested it? With your Qosmio or what?
Anyway, it is not easy to say what is wrong there. Try to test it with TV again. Connect your Qosmio to the TV using HDMI cable, switch to HDMI port on TV and use FN+F5 key combination to switch between LCD and TV.
Does it work?
>so seems to be just the vga as the laptop sees the monitor when connected does that mean the vga port is ok?
How to understand this? Is desktop shown on the screen when you use VGA port?

Monitor Does Not Shut Down In 15 Minutes

Under power options the monitor is set to turn off on 15 minutes. updated my Shockwave Flash to 10.0 r42 when a flash video is played in any of of my browser and the browser is shut down the monitor does not shut down in 15 minutes. the computer has to be rebooted and then everything is fine. reinstalled Shockwave Flash 9.0 r124 for firefox opera and the situation is ok.
can not understand why the new flash causes this problem.
computer exceeds all of adobe requirements.
if a monitor does not shutdown in power schemes it usually indicates a process running in the bachground.
In this case there appears to be none and it would suggest there is a problem with Shockwave Flash 10.0 r42 and possibly with all shockwave
player 10 have that problem.
Last year tried another version of 10 and had the same problem
install_flash_player_ax.exe 9.0 r124 will not install on my computer as a pop up says its not the most current version.
install_flash_player_9_ax.exe 9.0.260.0 will install but on most sites a pop up will say flash 10 is required.
Dont know what adobe is up to but clearly something is wrong.
Many people have heard about third-party cookies, and some browsers even block those by default. Some people may even be using Private Browsing modes. However, only few seem to realise that Adobe's Flash player also leaves a cross-browser trail on your local hard drive, and allows for sending cookie-like information back to the server, including third-party sites. And because it is a plugin, Flash does not take any of the browser's privacy settings into account.
http://superuser.com/questions/1627/how-to-automatically-remove-flash-history-privacy-trai l-or-stop-flash-from-stori
Its surprising that no one has noticed this bug and also would like a working copy of install_flash_player_ax.exe 9.0 r124
Any comments would be appreciated.

filed a bug report with adobe.
the attachment will explain it.
the problem has been fixed in a future beta 10.

Laptop screen does not come on

My 1 year, 1 month old pavillion dv4 laptop\'s screen does not come on. At first I thought it was the screen. However after geek squad and one other computer repair place diagnosed it, they said it needs the motherboard replaced.
I currently have the laptop hooked up to a external monitor and it works fine in safe mode. Any suggestions where I can get a motherboard?

Hi there ,
Try Hard Reset
Link is given Below :
HARD RESET
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

ITunes does not recognize iPad due to "unknown error OxE80000565." Does this mean anything to anyone?

iTunes does not recognize iPad due to "Unknown error OxE80000565." Does this mean anything to anyone?

Hello pyloric
For that specific issue, check out the article below for the steps to walk you through to get your iPad talking to iTunes again.
iOS: Unknown error containing '0xE' when connecting to a Windows PC
http://support.apple.com/kb/TS3221
Regards,
-Norm G.

System does not come up after homogeneous system copy

Hi there,
after a regular system copy of our Java-only Portal the system does not come up.
'startsap' warns with these messages :
Warning : /usr/sap/SPE/JC51/j2ee/cluster/bootstrap/../server0/bin/ext/jdbdictionary/jddi.jar file stated but does not exist !
Warning : /usr/sap/SPE/JC51/j2ee/cluster/bootstrap/../server0/bin/ext/antlr/antlr.jar file stated but does not exist !
Warning : /usr/sap/SPE/JC51/j2ee/cluster/bootstrap/../server0/bin/system/frame.jar file stated but does not exist !
and, yes , these really important directories do not exist - under /usr/sap/<SID>/JCxy/j2ee/cluster/server0 there is
only ONE directory , which is 'apps' .
database starts, but not the j2ee engine
OS :Solaris 10, Oracle DB
I'm confused (i did the system copy 2 times, because I did not believe what I saw ....)
Regards,
Ronny

>
Sunny Pahuja wrote:
> Hi,
>
> Have you done system refresh with sapinst ?? was it successful or not ?? Could you please paste dev_server, std_Server and dev_dispatcher logs here ?
>
> Thanks
> Sunny
Hi Sunny,
thanx for your answer.
There are NO logs, either dev_server* nor dispatcher.
the only thing I found were under the work-directory, the dev_jcmon says :
[Thr 1] Wed Oct 27 11:01:40 2010
*[Thr 1] *** ERROR => Can't attach to administration shared memory (rc = 3) [jcmonxx_mt.c 228]*
and the bootstrap says mainly that it could not find the framework :
[Thr 1] JLaunchRequestQueueInit: create named pipe for ipc
[Thr 1] JLaunchRequestQueueInit: create pipe listener thread
[Thr 2] JLaunchRequestFunc: Thread 2 started as listener thread for np messages.
[Thr 3] WaitSyncSemThread: Thread 3 started as semaphore monitor thread.
[Thr 1] Tue Oct 26 10:00:01 2010
[Thr 1] SigISetDefaultAction : default handling for signal 18
[Thr 1] NiInit3: NI already initialized; param 'maxHandles' ignored (1;202)
[Thr 1] CPIC (version=701.2009.01.26)
[Thr 1] [Node: bootstrap] java home is set by profile parameter
Java Home: /usr/java
[Thr 1] JStartupICheckFrameworkPackage: can't find framework package /usr/sap/SPE/JC51/exe/jvmx.jar
That make 'sense', because there is nothing it could find ..
Regards Ronny

Monitor does not come on due to no input signal. Monitor is hp w2207. Hp media center pc m 260 N.

Similar Messages

Maybe you are looking for