Monitoring Cisco UCS Manager via HP System Information Manager 7.1 (SIM)

I am working with a customer to configure HP System Information Manager 7.1 (SIM) to monitor their Cisco UCS Manager.
The customer is looking to monitor the following:
- CPU Utilization on manager, blades, servers, etc...
- Memory utilization
- Network utilization
- System inventory
Alerting is needed for the following:
- Hardware failures: memory, power supply, drive, etc...
- Predictive failures
- Alert messages
I have the list of all the MIBs provided by Cisco but an having the following issues while loading them into HP SIM.
While loading MIB "CISCO-UNIFIED-COMPUTING-TC-MIB" I get the following error message:
Line 128: Error defining object: expected a label, found reserved symbol {
Line in MIB: SYNTAX Gauge32 {
Guage32 is imported from SNMPv2-SMI MIB
To get past this error I found a version of the MIB that removes all the textual conventions that where causing errors. I have attached the fixed MIB file to this discussion. With the fixed version of the MIB installed in SIM everything compiles and installs except the following two MIBS. CISCO-UNIFIED-COMPUTING-NOTIFS-MIBCISCO-UNIFIED-COMPUTING-CONFORM-MIB Questions:
1. Is there any way to get the CISCO-UNIFIED-COMPUTING-TC-MIB MIB to install correctly into HP SIM?
2. Is my MIB load order setup correctly?
3. Has anyone had success getting HP SIM to monitor and alert for Cisco UCS manager?
MIB Load Order:
SNMPv2-SMI
SNMPv2-TC
SNMP-FRAMEWORK-MIB
RFC1213-MIB
IF-MIB
CISCO-SMI
CISCO-ST-TC
ENTITY-MIB
INET-ADDRESS-MIB
CISCO-UNIFIED-COMPUTING-MIB
CISCO-UNIFIED-COMPUTING-TC-MIB
CISCO-UNIFIED-COMPUTING-FAULT-MIB
CISCO-UNIFIED-COMPUTING-NOTIFS-MIB
CISCO-UNIFIED-COMPUTING-AAA-MIB
CISCO-UNIFIED-COMPUTING-ADAPTOR-MIB
CISCO-UNIFIED-COMPUTING-BIOS-MIB
CISCO-UNIFIED-COMPUTING-BMC-MIB
CISCO-UNIFIED-COMPUTING-CALLHOME-MIB
CISCO-UNIFIED-COMPUTING-CAPABILITY-MIB
CISCO-UNIFIED-COMPUTING-COMM-MIB
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB
CISCO-UNIFIED-COMPUTING-CONFORM-MIB
CISCO-UNIFIED-COMPUTING-DCX-MIB
CISCO-UNIFIED-COMPUTING-DHCP-MIB
CISCO-UNIFIED-COMPUTING-DIAG-MIB
CISCO-UNIFIED-COMPUTING-DPSEC-MIB
CISCO-UNIFIED-COMPUTING-EPQOS-MIB
CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB
CISCO-UNIFIED-COMPUTING-ETHER-MIB
CISCO-UNIFIED-COMPUTING-EVENT-MIB
CISCO-UNIFIED-COMPUTING-EXTMGMT-MIB
CISCO-UNIFIED-COMPUTING-EXTVMM-MIB
CISCO-UNIFIED-COMPUTING-FABRIC-MIB
CISCO-UNIFIED-COMPUTING-FC-MIB
CISCO-UNIFIED-COMPUTING-FCPOOL-MIB
CISCO-UNIFIED-COMPUTING-FIRMWARE-MIB
CISCO-UNIFIED-COMPUTING-FLOWCTRL-MIB
CISCO-UNIFIED-COMPUTING-HOSTIMG-MIB
CISCO-UNIFIED-COMPUTING-IMGPROV-MIB
CISCO-UNIFIED-COMPUTING-IMGSEC-MIB
CISCO-UNIFIED-COMPUTING-IPPOOL-MIB
CISCO-UNIFIED-COMPUTING-IQNPOOL-MIB
CISCO-UNIFIED-COMPUTING-ISCSI-MIB
CISCO-UNIFIED-COMPUTING-LICENSE-MIB
CISCO-UNIFIED-COMPUTING-LLDP-MIB
CISCO-UNIFIED-COMPUTING-LSBOOT-MIB
CISCO-UNIFIED-COMPUTING-LSMAINT-MIB
CISCO-UNIFIED-COMPUTING-LS-MIB
CISCO-UNIFIED-COMPUTING-MACPOOL-MIB
CISCO-UNIFIED-COMPUTING-MAPPINGS-MIB
CISCO-UNIFIED-COMPUTING-MEMORY-MIB
CISCO-UNIFIED-COMPUTING-MGMT-MIB
CISCO-UNIFIED-COMPUTING-NETWORK-MIB
CISCO-UNIFIED-COMPUTING-NWCTRL-MIB
CISCO-UNIFIED-COMPUTING-ORG-MIB
CISCO-UNIFIED-COMPUTING-OS-MIB
CISCO-UNIFIED-COMPUTING-PCI-MIB
CISCO-UNIFIED-COMPUTING-PKI-MIB
CISCO-UNIFIED-COMPUTING-PORT-MIB
CISCO-UNIFIED-COMPUTING-POWER-MIB
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB
CISCO-UNIFIED-COMPUTING-PROC-MIB
CISCO-UNIFIED-COMPUTING-QOSCLASS-MIB
CISCO-UNIFIED-COMPUTING-SOL-MIB
CISCO-UNIFIED-COMPUTING-STATS-MIB
CISCO-UNIFIED-COMPUTING-STORAGE-MIB
CISCO-UNIFIED-COMPUTING-SW-MIB
CISCO-UNIFIED-COMPUTING-SYSDEBUG-MIB
CISCO-UNIFIED-COMPUTING-SYSFILE-MIB
CISCO-UNIFIED-COMPUTING-TOP-MIB
CISCO-UNIFIED-COMPUTING-TRIG-MIB
CISCO-UNIFIED-COMPUTING-UUIDPOOL-MIB
CISCO-UNIFIED-COMPUTING-VM-MIB
CISCO-UNIFIED-COMPUTING-VNIC-MIB
References:
ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html#_Toc303691433
http://www.hp.com/wwsolutions/misc/hpsim-helpfiles/simsnmp.pdf

Please post "debug ccsip messages".
Based on your debug you are getting "Cause No. 38 - network out of order."
You may want to bind SIP to an interface that the IP address is defined which Lync points to.
Chris

Similar Messages

Monitoring Cisco UCS Devices

Hello,
We have 2 setup of Cisco UCS Setup in our Company and both are located in different geographical location. (4 Fabric interconnect and 6 Chassis and 48 Blade servers)
We want to monitor whole Cisco UCS Components like Fabric Interconnect which include all ports and Expansion Module, Port utilization, Chassis with IOMs and Blade Servers, Bandwidth utilization, and power utilization so and so forth.
Please let me know if there is any tool, plugin, application is available to monitor all these components and get the reports out of them.
Regards,
Amit Vyas

Hi Craig,
I have installed Solarwinds NPM 10.1.3 Evaluation version and I am able to add Fabric Interconnect but this only give me date of following things
Average Response Time & Packet Loss
Last 10 Errors & Failures
Current Percent Utilization of Each Interface
List of VSANs
Connectivity Unit Status
However it doesn’t show the power utilization status of Fabric Interconnect
Another thing is when I was trying to add Blade Server into monitoring I was unable to do it manually hence I tried thru discovery wizard and it went successfully and blade servers got added into monitoring but it only give Average Response Time & Packet Loss nothing apart from this. Do I have to do anything else to get all relevant data for blade or I will only this much data in this in Evaluation version.
Thanks,
Amit Vyas

CISCO UCS state is no monitored

Hey Team,
got a new challenge to monitor CISCO UCS, as per the link below
completed all the necessary configurations but still the the state view says not monitored.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/msft_tools/scom/scom_2-6/scom_2-6_user_guide/scom_2_6_userguide.html
http://stefanroth.net/2012/06/24/scom-2012-monitoring-cisco-ucs-part-1-emulator-setup/
any ideas what might be wrong.
thanks in advance.
-vrkumar01
RajKumar

Yes on the Root folder of Cisco UCS there is an Event view called Management Pack Events. If there are events in that view take a look at them as they could be the cause of the problem. Also you should make sure SNMP is configured properly on the SCOM box
with the proper community string etc. this will also cause issues with connecting to the UCS box.
hope this helps!
Scott Moss MVP (Operations Manager) President - System Center Virtual Users Group |Vice President - Atlanta Southeast Management Users Group (ATL SMUG)
Please remember to click “Mark as Answer” on the post that helps you!
my new blog om2012.wordpress.com

UCS Management Pack for System Center 2012 OpsMgr add monitor wizard error

We're successfully using the 2.6.0.179 version of the UCS Management Pack for System Center 2012 Operations Manager in our 2012 SP1 OpsMgr environment; however, in the new 2012 R2 OpsMgr environment we've stood-up and in which we installed the 2.6.2.0 version of the UCS MP, we're getting an error when trying to run the Add Monitoring Wizard under the Management Pack Templates node of the Authoring pane. We get the same error from the 2.6.1.0 version of the UCS MP as well. The text of the error is as follows:
"The page [Cisco.UCS.MP.UI.Proxy.Template.Page.ProxyDetailsPage] in the assembly [Cisco.UCS.MP.UI.Culture="",PublicKeyToken="6c96076cdf2c87a",Version="2.6.0.0"] could not be loaded. Please make sure that the account you are running under has sufficient privileges to load the given assembly, or the management pack that defines this page is installed or the assembly containing the page is in the path of the executible or that the page derives from known Operations Manager page type."
I'm an admin user in OpsMgr, so this should not be a user privilege issue, and that leaves the MP itself. The fact that a 2.6.0.0 version is mentioned makes me wonder if the base version of the MP must be installed before the 2.6.2 version. I'd test this, but we no longer have that version, and its no longer available for download from Cisco that I can see.
Has any dealt with this issue successfully, or have any insight into the problem?

Solved...the requirement is that you must do the MP configuration from the SCOM console on the SCOM Management Server where you installed the Cisco UCS MP; you can't do it from a SCOM console on a remote computer like I was trying to do.

Cisco UCS Management Pack for System Center Operations Manager 2007 R2 Login Error

I have Cisco UCS 1.4 (3q) and just installed the MP v2.1 for Cisco UCS, however when I click on the "Management Pack Events" alert view in the SCOM console, there are error for event number 19900. The description of the error is as follows:
Description:
CISCO UCS R2 MP (https://10.x.x.x/nuova) [CISCO.UCS.R2.Proxy.LoadCache.ProbeAction.vbs] : CISCO UCS Login Error: Authentication failed (Code: 551)
I noticed that it's looking for the /nuova directory, but in order to login to our UCS environment, we usually just go to the IP address - so I'm wondering if that has something to do with it? I've verified that when going directly to the IP from Internet Explorer I can login using the opsmgr credentials we specifically created for this account. I've also gone through the process of creating a run-as account on the SCOM side and associated it with the correct profiles.
Any help is greatly appreciated.

Troubleshooting has found out its user error, wrong password configured.

Cisco UCS Managment interface

Hi Dear
Which is the function of the management interface of a Cisco UCS server? Only monitoring ?
Best Regards

Hi,
The management interface present in the Cisco UCS C-Series is a out-of-band interface that provides to you access to Cisco Integrated Management Controller (CIMC) where you can perform all management/monitoring tasks related the hardware set.
You can find more information about the CIMC in this link:
http://www.cisco.com/c/en/us/support/servers-unified-computing/ucs-c-series-integrated-management-controller/tsd-products-support-series-home.html
Regards,
Richard

Cisco UCS with FEX system Component requirements

Hi ,
I am looking for quick suggestion for required components to have a VMware vSAN implemented using FEX system with maximum Fabric trough put. Ideally a configuration for without multipath using single Fabric switch and later on to be able to upgrade to Multipath fabric.
We are in great rush to provide POC concept and was looking if you folks can suggest me on this. If need be you want to talk to me more in detail I can available.
Appreciate your help here.
Who can I reach to able to pull up build and quote the configurations for implementing complete UCS solution.
Are these below components absolutely required ?
2 x Nexus 2232PP 10GE Fabric Extenders
The Cisco Nexus 2232PP 10GE provides 32 x 10Gb loss-less low latency Ethernet and Fiber Channel Over Ethernet (FCoE) Small Form-Factor Pluggable Plus (SFP+) server ports and eight 10 Gb Ethernet and FCoE SFP+ uplink ports in a compact 1 rack unit (1RU) form factor. They enable Seamless inclusion of UCS rack servers into UCS Manager domain with UCS blade servers when connected to the UCS 6200 Fabric Interconnects, providing converged LAN, SAN, and management connectivity.
We currently have these below servers :
2 x UCSC-BASE-M2-C460
        524 GB RAM
        No SSDs
        No VIC Card
        4 x SAS 1 TB Drives
        1 x L1 Intel 1 Gbps Ethernet Adapter
        1 x L2 10Gbps Ethernet Adapter
        1 x LSI Mega RAID SAS 9240-8i (no RAID 5 support, Need a card that supports RAID5)
1 x UCSC-C240-M3L
        132 GB RAM
        30 TB SAS HDD
        1 x VIC Card
        1 x Intel I350 Gigabit Ethernet Card with 4 ports
        1 x LSI Mega RAID SAS 9240-8i (no RAID 5 support, Need a card that supports RAID5)
1 x 5548UP Nexus Switch ( Will I be able to use this switch in place of Nexus 2232PP 10GE Fabric Extenders to achieve complete UCS solution)

Cisco UCS Manager 2.2 supports an option to connect the C-Series Rack-Mount Server directly to the Fabric Interconnects. You do not need the Fabric Extenders. This option enables Cisco UCS Manager to manage the C-Series Rack-Mount Servers using a single cable for both management traffic and data traffic.
If you need high performance low latency (storage, for VMware VSAN), direct connection to UCS Fabric Interconnect and/or N5k is recommended.

Competitors for SAP Solution Manager within central system monitoring

Hello!
We currently use SAP Solution Manager (CCMS monitors from RZ20) for the central system monitoring for several SAP systems.
Are there some other tools/competitors that can also serve as central platform for system monitoring of several SAP systems?
(e.g. HP OpenView).
Many thanks!

Hello,
You may want to take a look into the EarlyWatch Alert report.
It's a weekly report that gives information about many different areas of your systems and helps you to maintain them. It helps to detect problems before they occur by analysing trends on your systems and alerting about it. It definitely may work taking a look into it: service.sap.com/ewa.
It does not have an additional cost, all you need is a solution manager.
Regards,
Daniel.
Edited by: Daniel Nicol on Apr 11, 2011 8:04 PM

Monitoring for Cisco UCS/Cisco Catalyst/EMC VNX/VMware environment

hi
I am not sure whether this is the right place for this post, but I am giving it a shot anyway.
I am looking for a monitoring solution for a Cisco UCS/Cisco Catalyst/EMC VNX/VMware environment and I cannot seem to find 1 product that does it all.
Do any of you Guys have experience with a such product?
thanks...

I have used PRTG for Cisco Routers/Switch, Vmware and with Cisco UCS. As for the storage part I'm not sure.
I recommend prtg because its user friendly and web based management.
Please Rate.

Monitoring of Standalone EP 7.0 system in Solution Manager 7.0

Hi Experts,
I need to configure Solution manager 7.0 for monitoring EP 7.0 (Stand alone ) system.
Can you share documents related to configuration of Solution Manager 7.0 for monitoring EP 7.0 system?
Thanks,
Anit

Hi,
EP Monitoring is done by Solution Manager Diagnostics.
Some Basis steps for ref
1. Definition of EP system thru SMSY in solution manager system
2. SMD agent installation in EP system with CCMS ping cofiguration in both solman and EP system
3. Wily Introscope Enterprise manager installation in solution manager system
3. From SMD wizard, you can configure the list of activities to be monitored for a EP system.
For detailed info check SMD installation guide
Regards
KT

Kerberos Configuration Manager for SQL Server: Access of system information failed!

I'm trying to use the new Kerberos Configuration Manager for SQL Server tool that was released recently to verify SPN on several SQL Servers, but any time I attempt to connect to a server I get the following error in the log:
6/24/2013 3:48:22 PM Info: Connect to WMI, \\<HOSTNAME>\root\cimv2
6/24/2013 3:48:25 PM Error: Access of system information failed System.DirectoryServices.AccountManagement.PrincipalOperationException: An error (1332) occurred while enumerating the group membership. The member's SID could not be resolved.
at System.DirectoryServices.AccountManagement.SAMMembersSet.IsLocalMember(Byte[] sid)
at System.DirectoryServices.AccountManagement.SAMMembersSet.MoveNextLocal()
at System.DirectoryServices.AccountManagement.SAMMembersSet.MoveNext()
at System.DirectoryServices.AccountManagement.FindResultEnumerator`1.MoveNext()
at System.Linq.Enumerable.Contains[TSource](IEnumerable`1 source, TSource value, IEqualityComparer`1 comparer)
at KerberosCM.WMIHelper.isUserLocalAdmin(SystemInfo si, UserPrincipal user)
at KerberosCM.WMIHelper.getUserInfo(SystemInfo mi)
6/24/2013 3:48:25 PM Error: Error System.Exception: Access of system information failed!
at KerberosCM.WMIHelper.getUserInfo(SystemInfo mi)
at KerberosCM.SystemInfo.GetInfo()
at KerberosConfigMgr.Utility.Login(String serverName, String login, String password, Boolean isCmdLine, Form uiForm)
Things I have tried to resolve this:
1. Verified that my account is a Domain Admin.
2. Attempt to connect locally without inputting any information for server/user/pw
3. Attempt to connect remotely using server/user/pw
I always receive the same error message and log: Access of system information failed!
Has anyone else run into this issue?

Update to this:
There were some invalid user accounts added to the Local Administrators group only showing up as a GUID. This caused the enumeration of the group to fail and generate the error in my original post. Removing those user accounts from the Administrators group
got past the enumeration error.
However, now when attempting to connect to the servers (locally or remotely) I get this error:
6/27/2013 10:24:24 AM Info: Connect to WMI, \root\cimv2
6/27/2013 10:24:38 AM Error: Access of system information failed System.Runtime.InteropServices.COMException (0x80070035): The network path was not found.
at System.DirectoryServices.DirectoryEntry.Bind(Boolean throwIfFail)
at System.DirectoryServices.DirectoryEntry.Bind()
at System.DirectoryServices.DirectoryEntry.get_AdsObject()
at System.DirectoryServices.PropertyValueCollection.PopulateList()
at System.DirectoryServices.PropertyValueCollection..ctor(DirectoryEntry entry, String propertyName)
at System.DirectoryServices.PropertyCollection.get_Item(String propertyName)
at System.DirectoryServices.AccountManagement.SAMStoreCtx.ResolveCrossStoreRefToPrincipal(Object o)
at System.DirectoryServices.AccountManagement.SAMMembersSet.MoveNextForeign()
at System.DirectoryServices.AccountManagement.SAMMembersSet.MoveNext()
at System.DirectoryServices.AccountManagement.FindResultEnumerator`1.MoveNext()
at System.Linq.Enumerable.Contains[TSource](IEnumerable`1 source, TSource value, IEqualityComparer`1 comparer)
at KerberosCM.WMIHelper.isUserLocalAdmin(SystemInfo si, UserPrincipal user)
at KerberosCM.WMIHelper.getUserInfo(SystemInfo mi)
6/27/2013 10:24:38 AM Error: Error System.Exception: Access of system information failed!
at KerberosCM.WMIHelper.getUserInfo(SystemInfo mi)
at KerberosCM.SystemInfo.GetInfo()
at KerberosConfigMgr.Utility.Login(String serverName, String login, String password, Boolean isCmdLine, Form uiForm)

Cisco UCS Management Pack Error

Hello,
I'm trying to configure the UCS Management pack for SCOM but when I try to configure in the Authoring pane, the IP + Username password, I have this error:
Data at the root level is invalid. Line 1, position 1.
I'm using the last version of the management pack, 3.0.2.
Any idea?
Thank you.
Regards,
Florent

Hello,
Check this below links
Release Notes for Cisco UCS Manager Management Pack for Microsoft SCOM MP 2.6.1:
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/msft_tools/scom/scom_2.6/scom_2.6_release_notes/scom_releasenotes_2_6.html
User Guide for Cisco UCS Manager Management Pack for Microsoft SCOM MP 2.6.1:
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/msft_tools/scom/scom_2.6/scom_2.6_user_guide/scom_2_6_userguide.html
https://communities.cisco.com/community/technology/datacenter/ucs_management/cisco_ucs_developed_integrations/blog/2013/10/18/cisco-ucs-manager-management-pack-for-microsoft-scom-version-261
Regards
keshav

Error: System.Management.Automation.RemoteException: Federation information could not be received from the external organization.

Greetings.
I'm getting 2 errors and 1 warning in the Hybrid Configuration object:
INFO : Session=Tenant Cmdlet=Get-FederationInformation -DomainName 'SanJuanCiudadPatria.com' -BypassAdditionalDomainValidation: $true START
ERROR : System.Management.Automation.RemoteException: Federation information could not be received from the external organization.
INFO : Session=Tenant Cmdlet=Get-FederationInformation FINISH Time=2620.7003ms
INFO : Session=Tenant Cmdlet=Get-FederationInformation -DomainName 'SanJuanCiudadPatria.com' -BypassAdditionalDomainValidation: $true START
ERROR : System.Management.Automation.RemoteException: Federation information could not be received from the external organization.
INFO : Session=OnPrem Cmdlet=Get-OrganizationConfig START
INFO : Session=OnPrem Cmdlet=Get-OrganizationConfig FINISH Time=203.229ms
WARNING : Office 365 was unable to communicate with your on-premises Autodiscover endpoint. This is typically due to incorrect DNS or firewall configuration. The Office 365 tenant is currently configured to use the following URL for Autodiscover
queries from the Office 365 tenant to the on-premises organization - https://autodiscover.SanJuanCiudadPatria.com/autodiscover/autodiscover.svc/WSSecurity. See the following article for further information: http://go.microsoft.com/fwlink/p/?LinkId=275838
Any help would be greatly appreciated.
Hello World.

Hello,
If the IIS configuration is missing the svc-Integrated handler mapping, the issue may occur. Please try to refer to the following KB to check if the issue can be solved.
http://support.microsoft.com/kb/2626696
Please check if there is A record for autodiscover on public DNS server or DNS SRV record.
Additional blog for your reference.
http://blogs.technet.com/b/mikehall/archive/2013/08/21/office-365-insight-into-the-hybrid-configuration-wizard-part-2.aspx
Cara Chen
TechNet Community Support

Conectar Cisco UCS via Nexus a NFS via IP

Tenemos una solución Cisco UCS la cual esta conectada a los Switches de Agregación Nexus y cuando se trata de conectar un o unos ServidoresVirtuales o SX a un NFS via IP no establece la conexión generando time-out, pero si la solución Cisco UCS es conectada a unos 6500 que se comportan como unas extensiones del Nexus, si se establece la conexión sin problemas.

Si efectivamente tenemos este problema, los UCS conectados a través del Nexus llegan a establecer la conexión a los NFS luego de varios intentos se establece, cuando se hace la consulta de información se vuelve extremadamente lenta , los nexus en nuestra red son los Switches Cabecera de Acceso manejan la capa 3 del Datacenter y se encuentran conectados a ellos 4 Switches 6513 vía vpc como extensiones en capa 2, la conexión de los Fabrics de los UCS conectados tambien via vpc hacia ambos nexus, cuando se tenían conectados los fabrics en los 6500 la conexión hacia los NFS se establecía normalmente, tuvimos que sacar los servidores que requieren este tipo de conexión a unos Blade de IBM que están conectados a los 6500

Solaris File System/Device Management Information

Hi All,
I a writing a paper about the Solaris operating system and require information about the file system and device management of Solaris 8.
File Management:
I am looking for information or links to sites that would help me find more information about the solaris file system architecture, how it uses drive space, and some of the features of the Solaris file system
Device Management:
I am also looking for information or website links that cover how Solaris talks to devices (overview) and other device management architecture information.
any help is appreciated!

Don't use cp because it converts soft links into hard files. Its even worse when you have cyclic soft links. Use tar or cpio and you should be ok.
i.e. If you have a soft link to a file of 10G, a cp will result in 20G.

Monitoring Cisco UCS Manager via HP System Information Manager 7.1 (SIM)

Similar Messages

Maybe you are looking for