Multiple WLAN connections
Does anyone know of a way to get my PODCAST and Email applications to use multiple WLAN connections?
I spend most of my day in one of two places, each with a different WLAN, and I'd the phone to have the sense to change WLAN connection as they become available.
Thanks for your time.
Depends, on what your phone is.
If you're using an N97 or a 5800, or anything running on s60v5 for that matter, Go to Menu>Settings>Connectivity>Wireless LAN>Options>Settings>Show WLAN availability. Then you can also set how often it will set to scan for WLAN connections. This would allow the phone to scan for WLAN hotspots around you immediately. Be warned however that this will drain your battery faster.
On an s60v3 phone, I am not very familiar but from what I know its in Menu>Tools>Connectivity>Wireless LAN>Options>Settings>Show WLAn availability.
If you find my post helpful please click the green star on the left under the avatar. Thanks.
Similar Messages
-
Multiple WLANs & DSL connection
Has anyone had any experience with configuring multiple WLANs feeding into a single DSL connection?
I need to set up WLANs in 4 separate rooms that each have single cable back to a switch and a DSL connection.
The idea is that each room will be stand-alone as far as the WLAN is concerned and when they need Internet access they plug into the Ethernet port in the wall which is cabled back to the switch and DSL.
Each room will have a 4-port wireless router with DHCP server configured (the 4-ports are for those without wireless). Initially security won't be an issue but we realise that VLANs will probably be required down the track and a managed level-2 or 3 switch will be required. For now we are happy to just use separate wireless routers with minimum security.
I am assuming something like a WRT54G will do the job but how to configure the WLANs? Different SSIDs and channels? Could we use different networks (eg 192.168.1.x and 10.0.0.x) and then would we need to bridge them etc?
KHi .. you can definitely configure the routers in the way you have described. You will have to set up different ssid and channel on each router in each room. Also you have to use different networks.Say eg 192.168.1.1 on the 1st router and 192.168.2.1 on the 2nd router and so on.
-
How to execute "netsh wlan connect SSID", but SSID has space and quotation marks?
Dear all:
I have a wifi roruter with SSID test "3"
But when I execute following command netsh wlan connect "test \"3\""
the netsh reply: 未將設定檔 "test " 指派給指定的介面。
Sorry my windows7 is chinese version, but as you can see, netsh detect my SSID as
test, not test "3".
Does everybody know how to use netsh to connect to a SSID, and these SSID has space and quotation mark both?
Regards,
JosephHi Joseph,
Firstly, please modify your SSID name to make sure it do not contain spaces or special characters. SSID name is the router setting. please go there to change SSID name.
In addition, If only one SSID is specified in the profile, then the specified SSID is used to connect, and the ssid parameter is not required. If the profile specifies multiple SSIDs, the ssid parameter is required.
Therefore, I would like to suggest you run command as this syntax:
netsh wlan conncet ssid=Your SSID of the unsecured wireless network name=Your current profile name
To do this, please refer to the section “connect” in the following document:
Netsh Commands for Wireless Local Area Network (WLAN) Preliminary
http://technet.microsoft.com/en-us/library/cc755301.aspx#bkmk_wlanConn
Karen Hu
TechNet Community Support -
Our home network has multiple devices connected by iCloud: 2 iMacs, 2 iPhone 4s, 1 MacPro Laptop, and 1 iPad 2. When using Calendar, all the events were
duplicated on my husbands iMac. On his computer, under Calendar accounts, I had included iCloud and also my iCloud ID. I thought that because I had two accounts listed that were connected to iCloud, that might be the cause of the duplication. When I deleted ithe calendars from one of the accounts, it resulted
in deleting all of the events on all of our network devices!
I have since entered some new events into Calendar from my iMac and from my iPhone. These appear correctly on all devices except my husband's iMac where they are again all duplicated.
I have two questions: 1) How can I eliminate the duplicated events on my husband's computer and 2) How do I retrieve the old wiped out Calendar events from
Time Capsule. I don't know how to find Calendar in the Time Capsule. If I find the Calendar information in Time Capsule, how do I transfer it to my current Calendars?
I was obtaining phone help from one of the Apple techs at Apple Support, but our call was disconnected part way through. Didn't know how to reconnect with the tech.
Thanks for any help.The warranty entitles you to complimentary phone support for the first 90 days of ownership.
-
Good morning everybody,
I am writing on behalf of not being able to implement a desired outcome in our company network. In fact the situation is as follows:
What I want to do is to be able to authenticate users (802.1x authentication) in our company radius server and authorize them access by having a dynamic VLAN assignment in a multi-user environment on one and the same port of a Cisco 2960 switch. So far, the authentication and authorization has been working completely smoothly (there are no problems with itself). The concept involves the configuration of both DATA and VOICE VLANs as I there is also phone authentication implemented. In order to simulate this environment I introduce a Dumb switch connected to my Cisco 2960 Catalyst.
What I have successfully managed to get to work so far is this:
1) On one switch port I have tried the “authentication host-mode multi-domain” and it worked perfectly for a PC behind a telephone, or with one PC connected to a the dumb switch + the telephone connected to another port of the dumb switch. Logically it is the same situation as there is a separation in two domains – DATA and VOICE. Bellow is an output from show authentication sessions for this scenario.
Interface MAC Address Method Domain Status Session ID
Fa0/23 0021.9b62.b79b dot1x DATA Authz Success C0A8FF69000000F3008E (user1)
Fa0/23 0015.655c.b912 dot1x VOICE Authz Success C0A8FF69000000F9009F (phone)
2) On the other hand, when I try the same scenario with the “authentication host-mode multi-auth”, the switch still separates the traffic in two domains and is able to authenticate all users, AS LONG AS they are in the same VLAN.
show authentication sessions:
Interface MAC Address Method Domain Status Session ID
Fa0/23 0021.9b62.b79b dot1x DATA Authz Success C0A8FF69000000F3008E (user1)
Fa0/23 b888.e3eb.ebac dot1x DATA Authz Success C0A8FF69000000F8008C (user2)
Fa0/23 0015.655c.b912 dot1x VOICE Authz Success C0A8FF69000000F9009F (phone)
However, I cannot succeed authentication of many users from DIFFERENT VLANs, neither in multi-auth nor in multi-domain modes.
What I want to get is an output like this:
Interface MAC Address Method Domain Status Session ID
Fa0/23 0021.9b62.b79b dot1x DATA Authz Success C0A8FF69000000F3008E (user1)
Fa0/23 b888.e3eb.ebac dot1x DATA Authz Success C0A8FF69000000F8008C (user2)
Fa0/23 0015.655c.b912 dot1x VOICE Authz Success C0A8FF69000000F9009F (phone)
I want the switch to authenticate the users anytime they connect to itself and for them to have an instant access to the network. (I tell this because I tried scenario 1) with multi-domain mode and authentication violation replace, and it worked but, two users never had access to the “Internet” simultaneously!!!
The configuration of the interface connected to the Dumb switch is as follows.
interface FastEthernet0/x
description Connection to DUMBswitch
switchport mode access
switchport voice vlan XXX
switchport port-security maximum 10
switchport port-security
switchport port-security violation protect
authentication host-mode multi-auth
authentication priority dot1x
authentication port-control auto
authentication timer reauthenticate 4000
authentication violation replace
dot1x pae authenticator
dot1x timeout tx-period 10
spanning-tree portfast
The way I see it is explained in the following steps:
- PC1 connects to the Dumb switch. This causes the Cisco switch to authenticate user1. This creates an auth. session with its MAC address linked to a domain DATA.
- When PC2 connects to the Dumb switch, this causes the violation replace which replaces the recent authenticated MAC address with the MAC of PC2. I would like it once authenticated to appear in the authentication sessions with a link to a new DATA domain linked to the VLAN assigned from the RADIUS server.
Is this possible? I think (in theory) this is the only way to provide authenticated access to multiple users connecting through Dumb switch to the network.
Has anybody ever succeeded in such a configuration example and if yes, I would be love to get some help in doing so?
Thank you
Stoimen HristovHi Stoimen,
I have done a setup similar to yours with the only exception being VLAN assignment. When I used dACLs only, it makes things somewhat easier as the VLAN no longer matters. Remember that the switchport is in access mode and will only allow a single VLAN across it (with the exception of the voice VLAN). I think that is the real cause of your problem.
From what I can see, you have 2 options available to you:
1) Use dACLs instead of VLAN assignment. This means that an access list will be downloaded from the radius server straight to the authenticated user's session. I have tested this and it works perfectly. Just Google Cisco IBNS quick reference guide and look for the section that deals with Low Impact mode.
2) Get rid of the dumb switches and use managed switches throughout your network. Dumb switches will always be a point of weakness in your network because they have no intelligence to do advanced security features like port security, 802.1x, DHCP snooping, etc.
Hopefully someone else will chime in with another option.
Xavier -
Multiple DataBase Connection in a Single Form
hi all
Is it Possible to have Multiple Database Connection With a Single Form
Block a : Retriving data from a database Service a/Schema A.
Block b : Retriving data from a Remote Database Service b / Schema B.
If yes how to do this.
regards
jai
email:[email protected]Sure you can access a database this way,
but can you base a block on this database connect? No you can't.
Frank -
IOS device failed to get ip address on multiple wlan on the same anchor controller
Dear Experts:
in my implementation, we need 2 WLANs be served on the same anchor controller.
WLAN1: wep/40bit, integration with NAC/OOB on anchor controller for guest wlan service.
and guest account controlled by NACguest server.
WLAN2: wep/40bit, no layer3 secuirty for temporary using.
foreign controller: WiSM on v6.0.196.4 (also testing on 6.0.182.0)
anchor controller: WLC4402 on v6.0.196.4
on WLAN1:
Windows7 client get ip address correctly.
iOS (iPhone4 on 4.3.1/4.3.2, iPad2 on 4.3.1/4.3.2) can get ip address correctly on WLAN1.
WLAN2, iOS device cannot get ip address.
compare with debug message "debug clien mac" + "debug dhcp message enable"
on both foreign and anchor controller.
on foreign controller:
PM state has changed from: DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
on anchor controller:
PM state always stay on: DHCP_REQD (7) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
Enable/Disable DHCP Address Assignment Required is not work.
Enable/Disable DHCP proxy is not work.
Any hit this issue when get ip address failed in multiple WLANs on the same anchor controller?
In attachment log file,
DMZ.log: anchor controller on DMZ.
S3p1.log: WiSM on v6.0.182.0
S3p2.log: WiSM on v6.0.196.4
client mac: 00:1f:3b:05:33:c1, Windows7 Client
client mac: 58:55:ca:cf:d2:07, iPhone4 with 4.3.1,
WLAN1 subnet: 10.61.246.0/23
WLAN2 subnet: 10.61.248.0/23Hi, Nicolas:
just checking the attachment for the run-config on foreign/anchor controller.
DMZ_run.config - anchor controller
s3p1_run.config - WiSM on v6.0.182.0
s3p2_run.config - WiSM on v6.0.196.4
at this moment, we have disable the wlan 10 on foreign controller, and wlan 2 on foreign controller.
Wilson... -
Thinkpad X220: bad wlan connection when docked and lid closed
Dear forum
I use a Lenovo ThinkPad X220. I have no trouble with the wlan connection when i use the notebook alone. The wlan connection is also stable when i use the notebook plugged in the dockingstation with the lid open. But when I use the notebook plugged in the dockingstation with the lid closed my wlan connection drops regularely to about 2 Mbps and gets very unstable.
The ThinkPad uses the Intel Centrino Advanced-N 6205 wlan network controller:
$ lspci | grep 6205
03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 [Taylor Peak] (rev 34)
The network controller uses the iwlwifi driver, that comes with the current linux-firmware package:
$ pacman -Ss linux-firmware
core/linux-firmware 20150206.17657c3-1 [Installiert]
Firmware files for Linux
I didn't change any options of the kernel module, everything runs in default mode:
$ modinfo -p iwlwifi
swcrypto:using crypto in software (default 0 [hardware]) (int)
11n_disable:disable 11n functionality, bitmap: 1: full, 2: disable agg TX, 4: disable agg RX, 8 enable agg TX (uint)
amsdu_size_8K:enable 8K amsdu size (default 0) (int)
fw_restart:restart firmware in case of error (default true) (bool)
antenna_coupling:specify antenna coupling in dB (default: 0 dB) (int)
wd_disable:Disable stuck queue watchdog timer 0=system default, 1=disable (default: 1) (int)
nvm_file:NVM file name (charp)
uapsd_disable:disable U-APSD functionality (default: Y) (bool)
bt_coex_active:enable wifi/bt co-exist (default: enable) (bool)
led_mode:0=system default, 1=On(RF On)/Off(RF Off), 2=blinking, 3=Off (default: 0) (int)
power_save:enable WiFi power management (default: disable) (bool)
power_level:default power save level (range from 1 - 5, default: 1) (int)
fw_monitor:firmware monitor - to debug FW (default: false - needs lots of memory) (bool)
At first I thought, the problem could be caused by the KDE power saving settings. I changed the settings, so nothing happens when I close the lid (no hibbernation or screen lock or something like that), but without success (the wlan connection is still unstable under the described circumstances).
Also dmesg shows nothing that points out a problem (as far as I can see):
$ dmesg | grep iwlwifi
[ 19.688522] iwlwifi 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 19.688679] iwlwifi 0000:03:00.0: irq 31 for MSI/MSI-X
[ 19.696095] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
[ 19.718023] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled
[ 19.718027] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[ 19.718028] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[ 19.718029] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
[ 19.718145] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[ 19.753757] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[ 20.128443] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[ 20.128652] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[ 20.403905] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[ 20.404212] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[ 68.922975] iwlwifi 0000:03:00.0: L1 Enabled - LTR Disabled
[ 68.923192] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
So I have no idea where this strange behaviour comes from (only wild guesses: buildfactor, antenna orientation,...).
Any help would be really appreciated.hmmm...
how about checking both your wired and wireless nic drivers in device manager to make sure that the "allow computer to turn off this device to save power" checkbox on the power management tab is deselected.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee. -
What is WLAN connectivity, how to use it for inter...
hi all
i have nokia n79, i have know about WLAN connectivity, i mean how to use it. i just check it in my office it shows WLAN network found, i opend it and select start web browsing, then it asked select WLAN network there it already shows hidden WLAN, then i connected it through hidden WLAN then it asked WLAN network name, what is WLAN network name and how to use WLAN network for internet browsing. pls suggest me
thanks/regards
Chandrakant RajolkarThis will get you started.
http://en.wikipedia.org/wiki/Wireless_LAN
Check your user manual.
http://europe.nokia.com/get-support-and-software/product-support/nokia-n79/guides
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009 -
N95 WLAN Connection problems - Orange Livebox (UK)
I am trying to get the N95 to connect to the internet wirelessly through Orange Livebox (UK). I have run the WLAN wizard and the phone has identified it. I have input the WEP key and thats worked fine.......except everytime I try to connect to the net via this method I get a connection error. Has anybody else had WLAN connection problems? Can anybody help?
hi,
did you press "1" button at the back of the Livebox before pairing ?
what kind of error message do you get on the N95 ?
does it fail the same way when you go through the homescreen "WiFi scanning / Start Web Browsing" or through Tools / WLAN Wizard ?
Cheers, -
have a bought a hp pavilion g series. had trouble with installation and updates. now problem that firefox with wlan has no connection. suse linux 12.1, wireless lan 802.11, FRITZ!Box Fon WLAN 7270, find no setup for wlaan in firefox that over the laptop wlan connection will work
In Firefox 3.6.4 and later the default connection settings have been changed to "Use the system proxy settings".
See "Firefox connection settings" in [[Server not found]]
You can find the connection setting here: Tools > Options > Advanced : Network : Connection
If you do not need to use a proxy to connect to internet then select ''No Proxy'' -
Hi
I have a problem with an WRT54GL Router. It keeps losing the Wlan connection. Then I have to reboot the router to get it working again.
On some days everything works fine, and the other day I have to reboot every 5 minutes.
I don´t use P2P. So there are not many simultaneous connections. Mostly there are only one or two Wlan Clients active.
Between the Router and the Client is only one Wall. Signal Strenght is at all times above 85%.
Does anyone have an idea what might cause this?Try upgrading your router's firmware and reconfigure it from the scratch.
Click on this link for the instruction. -
Help!!!!!!!! WLAN connection E71
I have a problem with WLAN connection (E71), when I access my wlan, i receive a message saying " WLAN is already active, close it and try again".
Please, have someone any solution?
-
5800,Wlan connection appears as 'unknown', however...
Hi to everybody!.
I have an issue with wlan connections. I defined a new access point in wireless connections, and I put it into the 'internet' destination. The access point is saved as WLAN_XX, and works perfectly.
As soon as I disconnect it, and click to find wireless connections, something rare happens. When there is high signal, the connection appears as 'known'. However if there is low signal, appears as 'unknown'. Therefore I have to configure it again as a new connection (retyping the wep password),which as a consecuence, is saved as 'WLAN_X01)'.
I updated the firmware from 31.0.101 to 40.0.005. A saved connection always showed as 'known' (even when i had not enough signal to connect) when i used the old firmware (31.0.101). I don´t know if it´s a new feature or a bug or how it´s solved, someone knows? Thanks.angel_apm wrote:
Hi to everybody!.
I have an issue with wlan connections. I defined a new access point in wireless connections, and I put it into the 'internet' destination. The access point is saved as WLAN_XX, and works perfectly.
As soon as I disconnect it, and click to find wireless connections, something rare happens. When there is high signal, the connection appears as 'known'. However if there is low signal, appears as 'unknown'. Therefore I have to configure it again as a new connection (retyping the wep password),which as a consecuence, is saved as 'WLAN_X01)'.
I updated the firmware from 31.0.101 to 40.0.005. A saved connection always showed as 'known' (even when i had not enough signal to connect) when i used the old firmware (31.0.101). I don´t know if it´s a new feature or a bug or how it´s solved, someone knows? Thanks.
This is normal. You can delete this access point from the settings and re-save it.
If you want to thank someone, just click on the blue star at the bottom of their post -
Problem about financial reporting studio(assign multiple db connection)
Hi,
I need to assign multiple database connections to a grid in Oracle Hyperion Financial Reporting Studio
To do this, I performed the following steps:
- Open a report.
- In a grid, select one column for which I want to change the database connection.
- In the Column Properties sheet, click the Select Database Connection button, .
- In the Select a Database Connection dialog box, select a database connection from the Database Connection drop-down list, then Click OK.
- In the Map Dimensions Between... dialog box, map dimensions between the default database connection and the selected database connection. I do this by selecting a dimension from the pull-down list in the right column for each dimension in the left column.
- Optional: Select an alias table for the new database connection.
- Click OK.
But after last step I have received next error:
*; nested exception is:*
java.lang.NullPointerException
Can someone explain the source of this error?
And help me please solve this problem because I didn’t receive figures in that column where I changed database connection.
Thank you in advance!I'm sure that both DB connections has the same dimension hierarchy. I can open the repot, but in it I don't see figures in that column where I've changed database connection...
Maybe you are looking for
-
Hi My requirement is to retrieve the JNDI Names of the JMSConnectionFactory and the JMSQueue using the Connection factory or Queue name. In short im trying out a feasibility of reading the JNDI values for queues from weblogic config.xml instead of re
-
FI Posting Date should be same of Sales Invoicing Date.
Dear Experts, I have certain queries in mapping the below scenario: We are following the below sale cycle: Sales Order -> Delivery -> Goods Issue -> Invoicing (without releasing to Accounting) -> L.R. Entry -> Release to Accounting. As per above cycl
-
Oracle Management Agent 10.2.0.5 64-bit Solaris
I am installing Oracle Management Agent 10.2.0.5 on Solaris box. It has been installed successfuly on box1 and on box2 it is giving me error message "Error in invoking target tnsping nnfgt.o mkldflags client_sharedlib of makefile". I am wondering bot
-
Windows Intune Purchase Query for Microsoft Silver Competency Partner India
Hi Support We are having a query regarding purchasing of Windows Intune. We are Microsoft Silver Competency Partner with Partner ID: #####. We just want to know that is there any discount available for Microsoft Silver Competency Partner on purchasin
-
Problem w/ipod mini reseting/charging
I've been having a problem with my ipod mini (2nd. gen 4gb) not fulling charging even after 8 hours and then shutting itself off and reseting after a few minutes of use. I've read some of the posts and couldn't really find a solution yet. I've tried