N97 v2, time monitor

hello all...it seems nokia has removed the time monitor while making a call ?
wheneva ur on a call u cant see how much time you have been on the phone and can only see that when u disconnect it..this is so dissapointing ..why on earth did nokia remove this ??
bring it back nokia !
Solved!
Go to Solution.

thank you so much Ravi

Similar Messages

Where can i check in the real time monitoring tool if there are active calls in progress?

where can i check in the real time monitoring tool if there are active calls in progress?

Hi
Selecting Call Manager -->Call Process ---> call activity
HTH
Regards
Carlo

Prime infrastructure 2.0 Real Time Monitor?

Hi everyone,
I install PI 2.0 and I want to know how can i configure and use the Real Time Monitor option?
thanks

Hello Dawit,
Please check the following link, might be helpful,
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/2.0/configuration/guide/mon.html

REAL time Monitor setup

Hi,
In solution Manager 4.0, RFC connections are setup alerady for early Watch, and works fine...
I would like to setup Real Time System monitor any one of R3 system forexample DEV system...
I setup CCMS alert for Entrie system MTE with memory alerts and it working fine + i am getting mails
However I am having a bit of difficulty setting up a few simple "Real Time Monitors" in solution manager
Point will be rewarded as solution per solution given
Thanks in Advanced
J

http://service.sap.com/monitoring (or use the direct link Monitoring your SAP NetWeaver Components [original link is broken])
Follow the setup guide for a CEN (Central Monitoring System). It's not different than setting up any CEN on a Netweaver installation.
Markus

LMS 2.1 and nGenius Real-Time Monitor 1.4

Dear NetPros,
Is the LMS 2.1 and the nGenius Real-Time Monitor 1.4 can be installed on the same system?
Regards,
Steve

Yes, but not recommended. Keeping them on separate servers will be more beneficial.

Enterprise manager query execution time monitoring

I have a few Virtual machines ( each with Oracle client 11g installed ) in VMWARE and VBOX and have a host Win7 with a Oracle 11g database.
What I am trying to achieve is that when I run a query from one of the virtual machines, let's say SELECT * FROM table x, Enterprise manager will tell me how long it took to run that query.
I have looked at SQL Monitoring area of Enterprise manager but it doesn't straightaway pick up the execution times and is very lazy and unreliable.
All help will be greatly appreciated.

will tell me how long it took to run that query. use sqlplus
SQL> set autotrace traceonly statistics time on
18:48:10 SQL> select * from employees;
107 rows selected.
Statistics
       0 recursive calls
       0 db block gets
      15 consistent gets
       0 physical reads
       0 redo size
      10817 bytes sent via SQL*Net to client
     600 bytes received via SQL*Net from client
       9 SQL*Net roundtrips to/from client
       0 sorts (memory)
       0 sorts (disk)
     107 rows processed
18:48:22 SQL>

Real Time Monitor Tool - Charting

Afternoon all,
I am using RTMT 8.1 to monitor Call Activity on a specific H323 gateway within our voice network. I've produced the chart which is correctly showing me real time information over a period of a couple of minutes. However, I want to display the chart over a period of 24 hours.
Do I need to change the polling rate to 30 or 60 minutes and allow the chart to run for 24 hours before presenting it? Is there any way of producing historical data on RTMT? Any help would be apprecaited.
Regards, Jamie

Hi Jamie,
Indeed in RTMT itself you should be able to achieve it by setting in counter properties "No. of data points shown on chart" to 50.
Next form Edit > Polling Rate. Set it to 30 minutes. Now it shown over 24 hours but with sample rate of 2/hour it may not really be useful.
So it would be better to have a higher sample rate and use the "Start counter logging" option to log the results to a locale csv file. So you can review the data afterwards with permformance log viewer or with Windows permance (perfmon.msc) from that locale csv file. Though you would need to leave RTMT running to log this information.

Abap WebDynpro Response time monitoring.

Hi,
We are trying to monitor response time for Abap WebDynpro.
From SMICM u2192 goto u2192 Http log u2192 server display entries. We can see the response time as 43 milliseconds
07/May/2010:23:03:22 -0500] - "POST XXXXXXXX HTTP/1.1" 404 2118 [43] h[-]
By defining the parameter icm/HTTP_logging_0 we can adjust the %T value, but I want to use ALM (alert management) to send an alert if the response time is more than X seconds seconds.
I thought of using log file monitoring but help.sap.com says we can define condition like X > 3 sec send an alert instead it will search for exact error message.
I want to avoid writing script using awk(unix) as I do not have OS access.
Please let me know if anyone has automated Abap webdynpro monitoring or any other thoughts is appreciated.
Thanks,
Venkat.

HI Venkat,
Try to explore this MTE (Use CCMS) , not sure you can achieve what you need ...
WDAClass
WebDynproABAPClass
You can reach here
SID\sapserver_SID_00\Web Dynpro ABAP\CpuTime
Hope it will help

N97 sms time problem

I recently bought a N97 and I hale a problem with the time information in SMS messages.
I am in turkey a
nd mi time zone is set to GMT+2 which is correct for turkey.
The problem is that:
normally time in SMS messeges ara correct but in some messeges (seems to be random) time is shown 1 hour early. So my new SMS ses not appear on the top of the list.
The problem is not contınuous it happens time to time.
Does anyone face same problem?
Is there a solutson to this?

in time and date settings is it set to auto update this is a network feature
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

RAC 11gR2 DB Time monitor script

Hi,
I need to monitor DB Time in my RAC 11gR2 environment, in redhat linux.
Could you please provide me a script to monitor the DB time resource?
I am not licensed to use diagnostic pack.
thank you

/u01/app/11.2.0/grid/bin/ocrcheck
Status of Oracle Cluster Registry is as follows :
Version : 3
Total space (kbytes) : 262120
Used space (kbytes) : 2392
Available space (kbytes) : 259728
ID : 264487450
Device/File Name : +DATA
Device/File integrity check succeeded
Device/File not configured
Device/File not configured
Device/File not configured
Device/File not configured
Cluster registry integrity check succeeded
Logical corruption check succeeded

Cisco Unified Real-Time Monitoring Tool Administration Guide

Hello Pros,
I am in process of upgrading CUCM from 8.6 to 9.1.2 and receiving "not enough disk space on the partition" error.
The show status from CLI shows 13499216K free space but I don't understand why we are getting the error message. I tried FTP and SFTP, from GUI and CLI with no luck. Do I need to start deleting files (traces, firmwares, etc..)? Even if I do so it wil free up the space in active partition and change nothing in my inactive partition as all thoses files are in my active partition. Your help is very much appreciated.
Memory Total:        4016964K
        Free:         161516K
        Used:        3855448K
      Cached:        1745416K
      Shared:              0K
     Buffers:           9216K
                        Total            Free            Used
Disk/active         14410496K        2301468K       11960264K (84%)
Disk/inactive       14410560K       13499216K         167512K (2%)
Disk/logging        50179664K       18651876K       28937612K (61%)
MK

Hi MK,
If the percentage of disk usage is above the high water mark that you configured, the system sends an alarm message to syslog, generates a corresponding alert in RTMT Alert Central, and automatically purges log files until the value reaches the low water mark. So, try lowering the high water mark value as well and then restart the Log Partition Monitoring service.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/service/6_1_1/rtmt/611-rtmt-admin/rtalert.html#wp1270174
HTH
Manish

Cisco CUCM session trace log viewer (in real-time monitor) doesn't show all calls

hi all,
could you please help with one trouble on CUCM 9.1: I activated CDR and set debug trace level as detailed and want to find history of my calls. I'm going to Tools -> CDR Analisys and Reporting and on the new appeared page i choose CDR -> Search by Phone Number. I make test call to my phone, try to search by my number phone but i doesn's see any incoming calls. It's worth noting that some outgoing calls i see. Could you explain why it is?

Did you set the service parameter to log calls into CDR?
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/service/8_0_2/car/CAR/caranrpt.html#wp1037699

Disabling time-only monitoring for a method

Hello,
I have a namespace "MyCompany" with a class "MyClass". MyClass has a method that is very CPU intensive (think loads of fast enumerations). I want to exclude this method from all monitoring including time monitoring.
Can I do this by disabling monitoring for that method in the methods dialog box (resource methods) or do I need to disable monitoring for the entire class under namespaces?
Thanks,
Peter

Hi Peter,
Both variants will work.
But if you choose the second variant (disabling the entire class within namespaces configuration), you won't see all the calls of that class in stack unless you add some calls explicitly within methods.
Igor Savchenko, VIAcode Consulting LLC (http://www.viacode.com/)

Real time data monitoring using multiple thermocouples via indicators and waveform

I apologize in advanced for this question is probably somewhat simple but I am brand new to labview as well as to the forum and could use some pointers. I have a CompaqDAQ with two 9213 16 channel modules and I am trying to read in 30 thermocouples into a waveform as well as display 30 indicators so I can label each indicator with the corresponding thermocouple for real time monitoring. Each thermocouple corresponds to a specific location and it is critical that the interface have an accurate indication or label for each one. I am wondering if there is an easy way to do this besides splitting the signal and having 30 thermometers on my block diagram? Perhaps an array of some sort? If I use an array to create the 30 thermometers, does the DAQ assistant automatically sort the thermocouples in increasing numerical order. For example, would the first and second indicators on my interface automatically be assigned to the a0 and a1 channels of the first module or would I have to do this manually? Same for the waveform? Thanks a lot!
PS - Not sure if this message needed more specifics but just let me know if more info is needed and I will provide!
Solved!
Go to Solution.

I see you are using the DAQ Assistant to create your task. Now I understand why you are asking about labeling. That is the NI Salesman's easy start up spiel... But anyway, have you ever created a task in MAX instead of using the DAQ Assistant? The interface is similar, and there may be a step or two more, but your end application will be more efficient and you will have more options with your data and properties. For instance, I tried to update the physical channel names in the DAQ Assistant setup ,which it does let you do, but it doesn't propagate that change forward to the waveform chart legend. Also, I don't know of any property node for that dynamic data type, although I never use it either. I suggest setting up your task and channels in MAX, if you don't mind giving it a go.
I wrote another example since I figured I didn't really lead you to the end with helping you out. It uses a cluster, although a little barbaric. I thought there was a more eloquent way of doing it by changing the labels, but I could not get it working as I anticipated.
Attachments:
TC Cluster Array Option.vi ‏28 KB

Monitor Date/Time activities routinely fail (Policy Stopped by User)

Hi guys,
Lately we've been creating a bunch of jobs in Orchestrator that are supposed to run every X minutes/hours. Usually these work fine however sometimes they either fail to run and actually stop the running Runbook in its entirety or fail to run but the next
time it's triggered it will run (but sometimes those runs will keep generating errors on some activities such as "Run .NET Script" until it is manually restarted.)
I've checked the Event Viewer but I don't see anything wrong at the time when the Runbook fails. I've also checked the Trace logs but they don't tell me much... (increased the level of logging in the meantime from 1 to 7 so maybe that will help). Not sure
what I am looking for either to be honest.
Anyone that has had this problem as well or any ideas what the cause may be (or where to start looking)? I really don't wanna go back to Windows Scheduled tasks :)

Hi,
also check the Orchestator Events (Tab Events in Runbook Designer). I suppose that a Runbook Server has problems to the same time "Monitor Date/Time" fails, perhaps contacting the Orchestrator Datastore.
"AuthorizationManager check failed" only happens sporadically for the same "Run .Net Script" Activity? Are the multiple Runbook Servers with different Logon Accounts for Orchestrator Runbook Service? (https://social.technet.microsoft.com/Forums/en-US/9fe7a237-05dd-4843-bf88-15be74e64c09/authorizationmanager-check-failed-run-net-script-only-on-runbook-server?forum=scogeneral)
Regards,
Stefan
www.sc-orchestrator.eu ,
Blog sc-orchestrator.eu
Hi Stefan,
Thank you for pointing me in the right direction. I think I found the source of the problem:
We basically have three Runbook servers and only one of them is designated as primary. One of the standby machines runs in a different domain. That would explain why we'd get the Authorization error as the Runbook service from the one domain tries
to run in the other. In any case it means that for some reason the Orchestrator decides to use a standby server instead of the primary one. For as far as I can see I the RunbookService.exe has been running for quite a long time but I do see some datastore
connection problems in the traces (perhaps a short disconnection during a vMotion of the Runbook server).
I've now used the Override option to designate only the primary server while I investigate further. But so far the jobs have been running without a problem.

N97 v2, time monitor

Similar Messages

Maybe you are looking for