NCS web interface crashed

Hi,
I was adding a map in NCS when the web interface crashed. I added 20 so far w/o issues. I refreshed the page and now i cannot access it through the web gui.
I can access it through ssh and I i did a sh application status NCS. this is what i noticed: NMS Server is stopped
I did:
ncs stop
ncs start
this is the output for sh application status NCS
Health Monitor is running, with an error.
failed to start NCS on startup Health Monitor
Reporting Server is running
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is stopped.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...
status
Any ideas?
Regards,
Eugen

And root access also works, showing that IP address is ok
Prime/Admin# root_enable
Password :
Password Again :
Root patch enabled
Prime/Admin# root
Enter root patch password :
Starting root bash shell ...
ade # ifconfig
eth0      Link encap:Ethernet HWaddr 00:50:56:A5:63:46
          inet addr:172.16.220.150 Bcast:172.16.220.255 Mask:255.255.255.0
          inet6 addr: fe80::250:56ff:fea5:6346/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:5781 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3335 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6312015 (6.0 MiB) TX bytes:586194 (572.4 KiB)
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:491842 errors:0 dropped:0 overruns:0 frame:0
          TX packets:491842 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:85107900 (81.1 MiB) TX bytes:85107900 (81.1 MiB)

Similar Messages

[SOLVED] CUPS Web interface crash when trying to Add Printer

I've used the web interface @ http://localhost:631
After a recent upgrade, when clicking Add Printer under the Admin tab, I enter the root username and password, and then the web interface "crashes". In Chromium, I get the "Aw, snap!" blue screen. In FireFox it just hangs forever.
In /var/log/cups/error_log I see
E [28/Nov/2009:14:46:19 -0500] Unable to set ACLs on root certificate "/var/run/cups/certs/0" - Operation not supported
I've tried removing /var/run/cups and it is recreated when cups is restarted, but same error. I haven't tried adding a printer via commandline because it looks difficult.
I've tried removing cups with pacman, and deleting /etc/cups/ /var/run/cups /usr/share/cups and anything else I could find and reinstalling, but no luck.
CUPS 1.4.2-1
perms on /var/run/cups 755 root:lp
perms on /var/run/cups/certs 511 daemon:sys
CUPSD running as root
/etc/cups/cups
root is a member of sys group
root is not a member of lp group (does this matter?)
Anyone have this problem?
Last edited by VitaminJ (2010-03-26 05:18:54)

Still having this problem. Even installed x86-64 Arch in a VM to see if a clean install works. NOPE!
First connection to http://localhost:631
D [24/Mar/2010:13:49:41 -0400] cupsdReadClient: 12 GET /admin HTTP/1.1
D [24/Mar/2010:13:49:41 -0400] cupsdSetBusyState: Active clients
D [24/Mar/2010:13:49:41 -0400] cupsdAuthorize: No authentication data provided.
D [24/Mar/2010:13:49:41 -0400] [CGI] argv[0] = "/usr/lib/cups/cgi-bin/admin.cgi"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[0] = "CUPS_CACHEDIR=/var/cache/cups"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[1] = "CUPS_DATADIR=/usr/share/cups"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[2] = "CUPS_DOCROOT=/usr/share/cups/doc"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[3] = "CUPS_FONTPATH=/usr/share/cups/fonts"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[4] = "CUPS_REQUESTROOT=/var/spool/cups"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[5] = "CUPS_SERVERBIN=/usr/lib/cups"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[6] = "CUPS_SERVERROOT=/etc/cups"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[7] = "CUPS_STATEDIR=/var/run/cups"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[8] = "HOME=/var/spool/cups/tmp"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[9] = "PATH=/usr/lib/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[10] = "SERVER_ADMIN=root@D830"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[11] = "SOFTWARE=CUPS/1.4.2"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[12] = "TMPDIR=/var/spool/cups/tmp"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[13] = "USER=root"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[14] = "CUPS_SERVER=/var/run/cups/cups.sock"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[15] = "CUPS_ENCRYPTION=IfRequested"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[16] = "IPP_PORT=631"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[17] = "LANG=en_US.UTF8"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[18] = "REDIRECT_STATUS=1"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[19] = "GATEWAY_INTERFACE=CGI/1.1"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[20] = "SERVER_NAME=localhost"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[21] = "SERVER_PORT=631"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[22] = "REMOTE_ADDR=127.0.0.1"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[23] = "REMOTE_HOST=localhost"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[24] = "SCRIPT_NAME=/admin"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[25] = "SCRIPT_FILENAME=/usr/share/cups/doc/admin"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[26] = "SERVER_PROTOCOL=HTTP/1.1"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[27] = "HTTP_USER_AGENT=Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.11 Safari/532.9"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[28] = "HTTP_REFERER=http://localhost:631/"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[29] = "REQUEST_METHOD=GET"
D [24/Mar/2010:13:49:41 -0400] [CGI] envp[30] = "QUERY_STRING="
D [24/Mar/2010:13:49:41 -0400] [CGI] Started /usr/lib/cups/cgi-bin/admin.cgi (PID 6441)
I [24/Mar/2010:13:49:41 -0400] Started "/usr/lib/cups/cgi-bin/admin.cgi" (pid=6441)
D [24/Mar/2010:13:49:41 -0400] cupsdSendCommand: 12 file=13
D [24/Mar/2010:13:49:41 -0400] [CGI] admin.cgi started...
D [24/Mar/2010:13:49:41 -0400] cupsdAcceptClient: 14 from localhost (Domain)
D [24/Mar/2010:13:49:41 -0400] [CGI] http=0x7f2bf62c7880
D [24/Mar/2010:13:49:41 -0400] [CGI] No form data, showing main menu...
D [24/Mar/2010:13:49:41 -0400] [CGI] /usr/share/cups/drivers/pscript5.dll: No such file or directory
D [24/Mar/2010:13:49:41 -0400] cupsdReadClient: 14 POST / HTTP/1.1
D [24/Mar/2010:13:49:41 -0400] cupsdAuthorize: No authentication data provided.
D [24/Mar/2010:13:49:41 -0400] cupsdReadClient: 14 1.1 Get-Subscriptions 1
D [24/Mar/2010:13:49:41 -0400] Get-Subscriptions ipp://localhost/
D [24/Mar/2010:13:49:41 -0400] Get-Subscriptions client-error-not-found: No subscriptions found.
D [24/Mar/2010:13:49:41 -0400] Returning IPP client-error-not-found for Get-Subscriptions (ipp://localhost/) from localhost
D [24/Mar/2010:13:49:41 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:41 -0400] Script header: Content-Type: text/html;charset=utf-8
D [24/Mar/2010:13:49:41 -0400] Script header:
D [24/Mar/2010:13:49:41 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:41 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:41 -0400] cupsdReadClient: 14 WAITING Closing on EOF
D [24/Mar/2010:13:49:41 -0400] cupsdCloseClient: 14
D [24/Mar/2010:13:49:41 -0400] cupsdSetBusyState: Not busy
D [24/Mar/2010:13:49:41 -0400] PID 6441 (/usr/lib/cups/cgi-bin/admin.cgi) exited with no errors.
Clicking on "Administration" tab:
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 12 POST /admin/ HTTP/1.1
D [24/Mar/2010:13:49:47 -0400] cupsdSetBusyState: Active clients
D [24/Mar/2010:13:49:47 -0400] cupsdAuthorize: Authorized as root using Basic
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[0] = "/usr/lib/cups/cgi-bin/admin.cgi"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[0] = "CUPS_CACHEDIR=/var/cache/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[1] = "CUPS_DATADIR=/usr/share/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[2] = "CUPS_DOCROOT=/usr/share/cups/doc"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[3] = "CUPS_FONTPATH=/usr/share/cups/fonts"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[4] = "CUPS_REQUESTROOT=/var/spool/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[5] = "CUPS_SERVERBIN=/usr/lib/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[6] = "CUPS_SERVERROOT=/etc/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[7] = "CUPS_STATEDIR=/var/run/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[8] = "HOME=/var/spool/cups/tmp"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[9] = "PATH=/usr/lib/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[10] = "SERVER_ADMIN=root@D830"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[11] = "SOFTWARE=CUPS/1.4.2"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[12] = "TMPDIR=/var/spool/cups/tmp"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[13] = "USER=root"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[14] = "CUPS_SERVER=/var/run/cups/cups.sock"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[15] = "CUPS_ENCRYPTION=IfRequested"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[16] = "IPP_PORT=631"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[17] = "CUPSD_AUTH_TYPE=Basic"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[18] = "LANG=en_US.UTF8"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[19] = "REDIRECT_STATUS=1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[20] = "GATEWAY_INTERFACE=CGI/1.1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[21] = "SERVER_NAME=localhost"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[22] = "SERVER_PORT=631"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[23] = "REMOTE_ADDR=127.0.0.1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[24] = "REMOTE_HOST=localhost"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[25] = "SCRIPT_NAME=/admin/"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[26] = "SCRIPT_FILENAME=/usr/share/cups/doc/admin/"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[27] = "REMOTE_USER=root"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[28] = "SERVER_PROTOCOL=HTTP/1.1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[29] = "HTTP_USER_AGENT=Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.11 Safari/532.9"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[30] = "HTTP_REFERER=http://localhost:631/admin"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[31] = "REQUEST_METHOD=POST"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[32] = "CONTENT_LENGTH=14"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[33] = "CONTENT_TYPE=application/x-www-form-urlencoded"
D [24/Mar/2010:13:49:47 -0400] [CGI] Started /usr/lib/cups/cgi-bin/admin.cgi (PID 6445)
I [24/Mar/2010:13:49:47 -0400] Started "/usr/lib/cups/cgi-bin/admin.cgi" (pid=6445)
D [24/Mar/2010:13:49:47 -0400] cupsdSendCommand: 12 file=14
D [24/Mar/2010:13:49:47 -0400] [CGI] admin.cgi started...
D [24/Mar/2010:13:49:47 -0400] cupsdAcceptClient: 15 from localhost (Domain)
D [24/Mar/2010:13:49:47 -0400] [CGI] http=0x7f0dfc5d5880
D [24/Mar/2010:13:49:47 -0400] [CGI] op="add-printer"...
D [24/Mar/2010:13:49:47 -0400] [CGI] do_am_printer: DEVICE_URI="(null)"
D [24/Mar/2010:13:49:47 -0400] [CGI] Getting list of devices...
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 15 POST / HTTP/1.1
D [24/Mar/2010:13:49:47 -0400] cupsdAuthorize: No authentication data provided.
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 15 1.1 CUPS-Get-Devices 1
D [24/Mar/2010:13:49:47 -0400] CUPS-Get-Devices
D [24/Mar/2010:13:49:47 -0400] cupsdIsAuthorized: username=""
D [24/Mar/2010:13:49:47 -0400] Returning HTTP Unauthorized for CUPS-Get-Devices (no URI) from localhost
D [24/Mar/2010:13:49:47 -0400] cupsdSendHeader: 15 WWW-Authenticate: Basic realm="CUPS", trc="y"
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 15 WAITING Closing on EOF
D [24/Mar/2010:13:49:47 -0400] cupsdCloseClient: 15
D [24/Mar/2010:13:49:47 -0400] cupsdAcceptClient: 15 from localhost (Domain)
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 15 WAITING Closing on EOF
D [24/Mar/2010:13:49:47 -0400] cupsdCloseClient: 15
D [24/Mar/2010:13:49:47 -0400] cupsdAcceptClient: 15 from localhost (Domain)
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 15 POST / HTTP/1.1
D [24/Mar/2010:13:49:47 -0400] cupsdAuthorize: Authorized as root using Local
D [24/Mar/2010:13:49:47 -0400] cupsdReadClient: 15 1.1 CUPS-Get-Devices 1
D [24/Mar/2010:13:49:47 -0400] CUPS-Get-Devices
D [24/Mar/2010:13:49:47 -0400] cupsdIsAuthorized: username="root"
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[0] = "/usr/lib/cups/daemon/cups-deviced"
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[1] = "1"
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[2] = "0"
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[3] = "30"
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[4] = "2"
D [24/Mar/2010:13:49:47 -0400] [CGI] argv[5] = "requested-attributes=all"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[0] = "CUPS_CACHEDIR=/var/cache/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[1] = "CUPS_DATADIR=/usr/share/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[2] = "CUPS_DOCROOT=/usr/share/cups/doc"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[3] = "CUPS_FONTPATH=/usr/share/cups/fonts"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[4] = "CUPS_REQUESTROOT=/var/spool/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[5] = "CUPS_SERVERBIN=/usr/lib/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[6] = "CUPS_SERVERROOT=/etc/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[7] = "CUPS_STATEDIR=/var/run/cups"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[8] = "HOME=/var/spool/cups/tmp"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[9] = "PATH=/usr/lib/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[10] = "SERVER_ADMIN=root@D830"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[11] = "SOFTWARE=CUPS/1.4.2"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[12] = "TMPDIR=/var/spool/cups/tmp"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[13] = "USER=root"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[14] = "CUPS_SERVER=/var/run/cups/cups.sock"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[15] = "CUPS_ENCRYPTION=IfRequested"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[16] = "IPP_PORT=631"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[17] = "CUPSD_AUTH_TYPE=Local"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[18] = "LANG=en_US.UTF8"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[19] = "REDIRECT_STATUS=1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[20] = "GATEWAY_INTERFACE=CGI/1.1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[21] = "SERVER_NAME=localhost"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[22] = "SERVER_PORT=631"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[23] = "REMOTE_ADDR="
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[24] = "REMOTE_HOST=localhost"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[25] = "SCRIPT_NAME=/"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[26] = "SCRIPT_FILENAME=/usr/share/cups/doc/"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[27] = "REMOTE_USER=root"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[28] = "SERVER_PROTOCOL=HTTP/1.1"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[29] = "HTTP_USER_AGENT=CUPS/1.4.2"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[30] = "REQUEST_METHOD=POST"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[31] = "CONTENT_LENGTH=91"
D [24/Mar/2010:13:49:47 -0400] [CGI] envp[32] = "CONTENT_TYPE=application/ipp"
D [24/Mar/2010:13:49:47 -0400] [CGI] Started /usr/lib/cups/daemon/cups-deviced (PID 6446)
I [24/Mar/2010:13:49:47 -0400] Started "/usr/lib/cups/daemon/cups-deviced" (pid=6446)
D [24/Mar/2010:13:49:47 -0400] cupsdSendCommand: 15 file=16
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/smb (PID 6447)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/socket (PID 6448)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/bluetooth (PID 6449)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/serial (PID 6450)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/parallel (PID 6451)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/snmp (PID 6452)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/http (PID 6453)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/usb (PID 6454)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/ipp (PID 6455)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/scsi (PID 6456)
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Started backend /usr/lib/cups/backend/lpd (PID 6457)
D [24/Mar/2010:13:49:47 -0400] [CGI] Flushed attributes...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Found device "ipp"...
D [24/Mar/2010:13:49:47 -0400] Script header: Content-Type: application/ipp
D [24/Mar/2010:13:49:47 -0400] Script header:
D [24/Mar/2010:13:49:47 -0400] [CGI] Flushed attributes...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Found device "socket"...
D [24/Mar/2010:13:49:47 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:47 -0400] Script header: MIME-Version: 1.0
D [24/Mar/2010:13:49:47 -0400] Script header: Content-Type: multipart/x-mixed-replace; boundary="CUPS-MULTIPART"
D [24/Mar/2010:13:49:47 -0400] Script header:
D [24/Mar/2010:13:49:47 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:47 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:47 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:47 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:47 -0400] [CGI] Flushed attributes...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Found device "lpd"...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6457 (lpd) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [CGI] Flushed attributes...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Found device "http"...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6453 (http) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [CGI] list_devices
D [24/Mar/2010:13:49:47 -0400] [CGI] usb_find_busses=7
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6455 (ipp) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6450 (serial) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [CGI] Flushed attributes...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Found device "scsi"...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6456 (scsi) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6448 (socket) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [CGI] Flushed attributes...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] Found device "smb"...
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6447 (smb) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6451 (parallel) exited with no errors.
D [24/Mar/2010:13:49:47 -0400] [CGI] usb_find_devices=11
D [24/Mar/2010:13:49:47 -0400] [cups-deviced] PID 6454 (usb) exited with no errors.
D [24/Mar/2010:13:49:49 -0400] [cups-deviced] PID 6452 (snmp) exited with no errors.
Clicking Add Printer button
D [24/Mar/2010:13:49:57 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:57 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:57 -0400] cupsdAcceptClient: 17 from localhost:631 (IPv4)
D [24/Mar/2010:13:49:57 -0400] cupsdReadClient: 17 GET /images/wait.gif HTTP/1.1
D [24/Mar/2010:13:49:57 -0400] cupsdAuthorize: No authentication data provided.
D [24/Mar/2010:13:49:57 -0400] [cups-deviced] PID 6449 (bluetooth) exited with no errors.
D [24/Mar/2010:13:49:57 -0400] PID 6446 (/usr/lib/cups/daemon/cups-deviced) exited with no errors.
D [24/Mar/2010:13:49:57 -0400] [CGI] Got device list!
D [24/Mar/2010:13:49:57 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:57 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] Regular expression "[a-z]+://"
D [24/Mar/2010:13:49:57 -0400] [CGI] lang="en_US.UTF8", locale="/en_US"...
D [24/Mar/2010:13:49:57 -0400] cupsdReadClient: 15 WAITING Closing on EOF
D [24/Mar/2010:13:49:57 -0400] cupsdCloseClient: 15
D [24/Mar/2010:13:49:57 -0400] PID 6445 (/usr/lib/cups/cgi-bin/admin.cgi) exited with no errors.
D [24/Mar/2010:13:49:57 -0400] cupsdSetBusyState: Not busy
D [24/Mar/2010:13:49:57 -0400] cupsdReadClient: 12 WAITING Closing on EOF
D [24/Mar/2010:13:49:57 -0400] cupsdCloseClient: 12
It's interesting how it says "Returning HTTP Unauthorized for CUPS-Get-Devices (no URI) from localhost" when I just entered my root username and pass in the HTTP BASIC Authentication popup.

WRV200 web interface crashes after changing config

I've got a WRV200 with firmware 1.0.24. Configured to run secured wifi and a VPN tunnel, all without a problem.
Now, when I disable the DHCP service on the box and click Save Settings I'm prompted with the "wifi will restart"message after which the web interface will stop responding. Other functionality (like VPN tunnel) stays OK. I'm connected wired and tried the change with Internet Explorer and Firefox. The only way to get access to the web UI again is do a powercycle of the WRV200. Then the config still shows DHCP enabled.
When trying to upgrade the firmware to 1.0.29 exactly the same happens: try to apply the upgrade, then the web interface stops responding in the end... and after a reboot the f/w still shows 1.0.24.
So: is anyone seeing the same ? And more so: does anyone know how to get around this ?

make sure that you upgrade the firmware from a hardwired computer...
go to ftp://ftp.linksys.com/pub/network and download the tftp.exe file .. assign a static ip address on the computer ( 192.168.1.10 ) and reduce the NIC card's speed to 10 Mbps half duplex mode...
run the tftp.exe file...here the server is router's ip add , password is router's password....browse the firmware file and click upgrade...
the firewall should be disabled during the complete process...
after the firmware upgrade , reset the router for 30 seconds and do a power cycle...

Mailman web interface crash

I have a crazy problem with my Mailman.
Web config interface and Server Admin config interface are not working. I am not able to change configs, add mailing lists, etc.
However, every old mailing lists are working perfectly.
I used:
sudo /usr/share/mailman/bin/check_perms -f
sudo /usr/share/mailman/bin/mailmanctl -s stop
sudo /usr/share/mailman/bin/mailmanctl start
Nothing happened. And my Web interface returns:
Not Found
The requested URL /mailman/ was not found on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
What could be happening with my Mailman? Could anybody help me?
I am not able to find anything that could help me, including in others Mailman discussions. Thanx a lot.

When I try to access www.xxx.com/mailman, I have:
Not Found
The requested URL /mailman was not found on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.

When is Linksys going to fix the WPS54g web interface that's crashing?

Since the last update 6049 in September 2005 which fixed problems but also introduced a new problem. If you used Firefox or Internet Explorer 7 both will completely crash the print server. Now with Internet Explorer 6 it works fine. The problem is you can't get Internet Explorer 6 with Vista, and also Microsoft is updating all Windows XP boxes to Internet Explorer 7 though the auto update. I love the web interface and the Admin tool is not as powerful as the web interface. There has not been an update since September 2005.Personally I use Ubuntu Linux and Firefox started crashing the server immediately with the update , but I needed. It was ok because I had a Windows VM with IE 6, and I figured Linksys wasn't going to give me the time of day. Any workarounds maybe?
(Edited for guideline compliance. Thanks!)Message Edited by JOHNDOE_06 on 02-21-200709:59 PM
Message Edited by jerone on 02-22-200701:08 PM
I ask Johndoe_06 that you not edit this into a question that is not relavent. The problem is a problem that Linksys needs to fix.Message Edited by jerone on 02-22-200701:09 PM
Message Edited by jerone on 02-22-200701:10 PM

This is not a security setting problem. Firefox first exposed this problem and now IE 7 is exposing it. The print server should not crash if a web browser is viewing it. No matter if you are under Windows or Linux . I first saw this problem using Firefox under Linux. But IE 6 worked fine under Windows. But now IE 6 is now gone to the way side and both Firefox & IE 7 send commands to access web pages is exposing a serious problem in the WPS54g firmware.Message Edited by jerone on 02-22-200701:10 PM

SFE-2010P Crash on web interface access

Hello!
I have 1 SFE-2010P with latest factory installed firmware 2.0.1.80 3/06/2008.
It's configured to be on access mode for a remote branch.
It has a trunk with other Linksys switch, which has a trunk with a core Catalyst switch.
There are several VLAN's on the switch.
Management IP is on VLAN 201,and has ip 192.168.201.42.
Everything works great until I try to get an access to Web Interface of the switch. From different VLAN and subnet (192.168.3.0/24) I'm connecting through
Catalyst 3750 to 192.168.201.42 (a /24 subnet). I log in as valid user (admin), and when the browser points me to http://192.168.201.42/home.htm
switch REBOOTS!!!!
Telnet (Menu and LCLI mode) works great, and doesn't reboot the switch.
SFE-2010 is a great hardware, and it's a most powerful from Linksys's switches.
So I hope you'll help me.
P.S.
Here is my config:
interface ethernet g1
switchport mode trunk
exit
vlan database
vlan 10,30,108,201
exit
interface ethernet e27
switchport access vlan 10
exit
interface ethernet g1
switchport trunk allowed vlan add 10
exit
interface ethernet g1
switchport trunk allowed vlan add 30
exit
interface range ethernet e(1-12,14-26,28-48)
switchport access vlan 108
exit
interface ethernet g1
switchport trunk allowed vlan add 108
exit
interface ethernet e13
switchport access vlan 201
exit
interface ethernet g1
switchport trunk allowed vlan add 201
exit
interface vlan 10
name pp-a
exit
interface vlan 30
name av
exit
interface vlan 108
name veda8_lan
exit
interface vlan 201
name Management
exit
no ip dhcp snooping verify
interface vlan 201
ip address 192.168.201.42 255.255.255.0
exit
ip default-gateway 192.168.201.12

If the management IP of your switch is 192.168.201.42, then it must be in VLAN 108 and not in VLAN 201 but assuming I didn't get it correctly, it seems that you're in the right track because as soon as you're asking to log-in to the admin page of the SFE switch, it means that you're using the correct and management PC of the switch. I would agree with you, you're supposed to access it and it shouldn't behave that way. Maybe you could still narrow down the setup of you network. I mean, maybe you could try changing the management VLAN or use the computer that is directly connected to that switch while accessing it. Thanks!

My iSQL*PLUS web interface has crashed

I had recently installed Oracle 9i release 1 with Apache Server 1.3. Since I had to work on PHP I upgraded my Apache Server to 2.2.4 version. Now I cannot use the web-interface of Oracle. How can i restore it back? I tried uninstalling Apache and Oracle and then reinstalling Oracle again. But no help.
Please do let me know how can i sort this out!!
Arindam
[email protected]

edit file :
$ORACLE_HOME/oc4j/j2ee/oc4j_applications/applications/isqlplus/isqlplus/WEB-INF/web.xml
look for :
<session-config>
<session-timeout>15</session-timeout>
</session-config>
and replace it by :
<session-config>
<session-timeout>180</session-timeout>
</session-config>
to get 3 hours time out
more information at :
http://download-uk.oracle.com/docs/cd/B19306_01/server.102/b14357/ch2.htm#sthref466

Web Interface of Cisco Prime 2.1 not working

Excuse me!
I install the trial version cisco prime 2.1 (OVA) on ESXi server
I can ping cisco prime but web interface of cisco prime not worinking
prime/admin# ncs status
Health Monitor Server is running.
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is running.
Plug and Play Gateway is running.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...

Services running fine..
check it with other Browser , Supported browser are below::
–   Google Chrome 31 or later.
–   Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
–   Mozilla Firefox ESR 24.
–   Mozilla Firefox 24, 25 or 26.
If above does not help , reboot the server once and check the issue again.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Open Bex workbook from BPS web interface,How hard it could be?

Hi all,
    I want to add a link or function-button in my BPS web interface,hope it could open a query(excel analyser),I tried 2 methods as follow:
   1. MIME , It can only open a static excel file, not a analyser query. I gave up this method.
   2. I use the program RRMX_START_EXCEL and add a plan function which is a EXIT in BPS0,in my EXIT function I used some code in RRMX_START_EXCEL,I test it in BPS0 ,it works ,it can open a analyser excel query.But when I put this plan function(including a parameter group ) in BPS_WB ,when I click the function-button in web interface, it crashed,says:
Error when processing your request
What has happened?
The URL http://bw1.:8000/sap/bc/bsp/sap/zwebcaxa001_998/page1.htm was not called due to an error.
The termination type was: TH_RES_FREE
and some other Error infomation,
Is it possible to realize my requirement? or Web interface and analyzer are just 2 total differrent things ,it is not possible to realize this?
thanks all

Hi Denny,
Have a look at www.javascript.internet.com and do a search for "whatfile".....
This should give you the javascript code whereyou can enter a file name (say an excel file name) and click a button to navigate to it.
Although I have not tried exactly what you have asked, I have successfully used parts of this code to open specified files (excel files) on our local directory from a BPS planning web page.
Obviously you will need to adapt the code to your specific evironment/situation...
Good luck.
Rael

Ix2 web interface not responding

I have the EMC IX2 200. I can no longer connect to the web interface. I recently had to replace a failed drive, I used the same model and size. Afterwards the mirror repaired itself but I could never manage the storage. Some message about the drives. The drive status showed fine in the mgmt interface. I downloaded firmware updates but it would not allow me to install. I tried rebooting the device but it never completed, even after waiting for than a day. It wouldn't respond to pings so I unplugged it the powered it back up. Now the web interface never comes back up. I can access my existing shares but I can't manage the device via the web interface. No service is listening on ports 80 or 443. I did have ssh enabled so I can access the system via a shell. Apparenty this is a common problem for which no known solution exists judging from numerous other forums. After rebooting all lights appear normal other than the white exclamation light keeps blinking. I've already spent many days on this issue but haven't given up on this product yet. Any suggestions?
[Port scan]
Scanning 192.168.1.15 [1000 ports]
Discovered open port 22/tcp on 192.168.1.15
Discovered open port 21/tcp on 192.168.1.15
Discovered open port 139/tcp on 192.168.1.15
Discovered open port 445/tcp on 192.168.1.15
Discovered open port 9000/tcp on 192.168.1.15
Discovered open port 873/tcp on 192.168.1.15
Discovered open port 49152/tcp on 192.168.1.15
Discovered open port 631/tcp on 192.168.1.15
Discovered open port 548/tcp on 192.168.1.15
Discovered open port 3689/tcp on 192.168.1.15

Yes, I'm not sure what is up with their tech support. I think they inherited a somewhat underwhelming product that had unrealized potential. I think it suffers from too much compromise on hardware for what they were trying to accomplish in software. It is somewhat maddening that they refused to use ssh to diagnose the problem. That is why it exists. I had it enabled when i first acquired this product to fix an issue at tech support's request. It appears everything booted up but something is wrong with the appweb service. The service is running but doesn't respond to connection attempts on 80 or 443. It isn't listening on the web ports. I still haven't heard back from their escalated support team. I wonder if it really exists? I've seen many other forums where a support issue got stuck here. The storage problem has worsened. I was copying all my data off when, in the middle, the share quit responding. The box would not power down, reboot or reset. I tried pulling power but still could not access the main share when it came back up where most my critical data resides. I connected in with ssh and traversed the directory tree, the base folder is there where the share would be advertised, but all the data is gone! I didn't get anywhere near a full copy completed. There are some other minor shares I had created and they still work, but I still cannot access the box via the appweb service, even though the process is running. Fortunately I can recover most my important data because I was also backing it up with Crash Plan (thank god!) but this will be very time consuming. I can't even begin to express how frustrating this process has been, not to mention the countless hours trouble shooting. Long story short, I wouldn't trust any important data on this device. I've ordered a Synology DS213j with two 3TB Western Digital RED drives to replace this. If I can get the ix2 repaired I will only use it for lab unless someone wants to buy it off me. -- thanks, David

Safari 2.0.4 and Yahoo Messenger Web Interface

I have been trying Yahoo's messenger web interface, which allows you to use your browswer instead of downloading the actual yahoo messenger. Whenever I goto sign out, safari crashes.
I have all latest updates, the latest flash player, etc.
Anyone have any experience with this new Yahoo Messenger Brower Interface and Safari?

Safari 3 fixed

Cisco Prime 2.0 web interface access

We just installed Cisco Prime Infrastructure 2.0 Express. It seemed to have installed correctly? But Two oddities. First when the system is restarted it takes and inordinate amount of time before the web interface becomes available. Once the web service is responding, it will not except ANY login credentials.
I can ssh to the instance and using cli, added two additional accounts. All accounts can access the install instance using ssh. None are able to login to the webinterface.
Thoughts as to what I may have missed?
Gabe

Please login to the CLI as admin then execute the command to change the password for the root WebUI acccount
     > ncs password root password Private123
     Loading USER - root
     Validating new password..
     Resetting password ..
     Resetting password COMPLETED.
     EXECUTION STATUS : Success
Once you've changed this password please then try to use those credentials to login to
the WebUI you indicated was presented in your response above.
Let me know if this does it. If not, we'll need to go a little deeper:::

Web Interface of Cisco Prime Infrastructure Not Working

Hi All,
I installed the trial version of Cisco Prime Infrastructure 1.2 on ESXi server.
It installed propersly and and i am able to ping it and also ssh into it.
But when I try to access it via web interface, it does not work.
I am provided with a login screen but after putting my credentials the page goes blank.
There also an error on the page "Error occured while fetching Meatdata for Slider Panel" and there is a advertisemnt to download Google chrome Framework.
When i do "NCS status" in CLI i see that every service is running.
Does anyone know how to solve this.
All your help is highly appreciated.

Google Chrome Frame isnt supported anymore, using Google Chrome doesnt work with all features and forget about Firefox. Up until this morning I had it working on IE11 but some update caused me to have this problem again. Cisco needs to get this fixed. I use several applications from Cisco and they still can't figure out a way to have them all work on a single browser.

Problems access to a web application (Web Interface or Web report)

Hi,
We found problems with the access to web application. Some users have problems with direct links to the web applications(Web Interface or Web reporting), when they click on the link an error message appears, the message displays the following text:
"Cannot open file Bex?sap-language=ENbsplanguge=ENcmd=idoc_TE.."
Clicking in details the message is "No Access to specified file"
For this users the access to excel reporting is correct, the message appears when they click on the direct web links through the browser or directly in BW system, but if they type the URL they can access. Other users can use the direct web link without problems.
I highly appreciate any help or idea about how to solve this issue.
Thanks in advance.

HI,
please ask to your basis that check the language of every single user on su01 tx.
This is the problem i think.
Natalia.

Unable to capture trace, when user logs in throuigh Web Interface

The Trace shows 'No Records Found', when user logs in through Web Interface of CRM. But there is Trace found, when the same user logs in through logon pad and carries out normal actvities.
sufficient auth. is provided.
Is there any setting in ST01, through which i can get trace , when user logs in through Web Interface
Regards

ST10 traces 1 instance only.
Your CRM web interface could use another instance than your backend. Go to transaction SM21, choose the appropriate server and run ST10 again.
Succes!
Kind regards,
Lodewijk Borsboom

NCS web interface crashed

Similar Messages

Maybe you are looking for