NForce3 chipset temp on K8N Neo2 Platinum

Hello I recently installed a new cpu and gfx cooler (Scythe Ninja Plus & ATI Silencer 5)
I had plans to install ZM-NB47J to but it just was to little space between gfx cooler and nf3 chipset.
My new coolers dosent give any "fresh" air to nf3 chipset like the stock ones so my System temp is up to 41-43C from 36C
What are normal temp on nf3 chipset and how hot can it get before my system gets unstable and maby cause damage to my motherboard?

Quote from: sleepy Samurai on 02-August-06, 03:06:20
My fan broke almost out of the box and with some talking I got a vantec cooler. It fits under those long video cards. The cooler is the same size as stock, cooper, larger fan, and heftier
It's always worth it to pick up a couple of those Vantec GPU coolers whenever you see 'em - they're the perfect replacement for the crap stock chipset fan - I put one on my Neo4 Plat as soon as I took the mobo out of it's box.
My Nf4 chipset stays at 32-35C no matter what.

Similar Messages

Passive chipset cooling on K8N Neo2 Platinum?

Hi,
I would like to hear from anyone with experience from replacing the active MSI HS on a MSI K8N Neo2 Platinum with a passive one, Zalman NB47J for example?
- Does the Zalman NB47J fit or is there another HS better suited?
- Are there problems with the VGA card since the AGP slot is so close?
- Heat problems. Would you recommend passive chipset cooling on K8N Neo2 Platinum?
I am not an overclocker but would like my system to be quiet.
Cheers
About to build:
Fortron PSU 350W FSP350-60PN
MSI K8N Neo2 Platinum
AMD64 Winchester 3000+
Thermalright XP-90
Powercolor 9800 PRO

Baskerville,
No problem mounting the Zalman NB47J
and no heatproblems for me so far ( with some good chassi airflow / ventilation )
The problem is the limited space between the cooler and the Graphic card.
I had to bend a couple of the zalman fins, to be able to mount my 6600GT card.
If not- the Grahpic card components hits the Zalman cooler.
It may work with some other passive cooler that´s lower then the zalman model.

Core Center wont show NB temp on K8N Neo2 Platinum

Is it just me or does core center not show my north bridge temp? i can control the fan speeds for the cpu and nb and it shows my cpu and system temp, but under my nb temp it doesn't show anything.
Is it because the board doesn't have a sensor for the north bridge? or is core center just screwing up??

There is no thing as system/case temp sensor on theese mobos.Only cpu & nv-chipset .
The temperature you see in corecenter as systemp is actually the nvidia chipset temperature .
Northbridge memory functions is taken over by the athlon 64 , thats why MSI finds it more reasonable to display
the nv-chip temp as systemp (remember that corecenter is an allround app for all msi mobos) .
Rest of the nb/sb functions are implemented as a single chip solution in the nvidia chipset chip.
So the traditional nb/sb solution is no longer existing.
The Athlon 64 and Athlon 64 FX each features its own integrated memory controller—single-channel for the Athlon 64 and dual-channel for the Athlon 64 FX. Instead of connecting to a traditional northbridge, these CPUs connect to a video card through a HyperTransport Graphics Tunnel. Data intended for components like PCI cards, disk drives, and USB peripherals is then routed through a HyperTransport I/O Hub, which is embedded in the core logic chip.
http://www.techworthy.com/PCUpgrade/NovDec2003/Athlon-64.htm?Page=5

MOVED: Drivers nForce3 ultra on MSI K8N Neo2 platinum and Vista?

This topic has been moved to Vista problems.
https://forum-en.msi.com/index.php?topic=109347.0

The 5.10 works fine - 5.11 has cause network problems for most people. There are better (V4.79) IDE/SATA/RAID drivers available if you want to do your own mix: DL the 6.37 Beta from here http://downloads.guru3d.com/download.php?det=971 and replace the IDE subfolder in the C:\NVIDIA folder from unpacking the 5.10 nVidia driver pack with the IDE folder from the 6.37 Beta, then run the Setup.Exe in the 5.10 subfolder. 6.37 Beta was nVidia's early attempt at a unified nForce3/4 driver pack but they gave up the unified idea without ever publishing one. There may even be better "mixes" available but this works for me and I've been running a RAID-1 with them for 2 years now with no faults.

Passive cooler for mobo chipset on MSI K8N Neo2 Platinum

One of my customers has this motherboard, which has a noisy motherboard chipset fan. I would prefer to replace it with a passive cooler if possible. Does anyone have any opinions on this and/or recommendations for compatible products I could go for?

Look here for suggestion:
https://forum-en.msi.com/index.php?topic=98720.msg777240#msg777240
http://www.newegg.com/Product/Product.asp?Item=N82E16835109131
https://forum-en.msi.com/index.php?topic=69147.0
http://www.pcsilent.de/showProduct.do?id=revnbbl&lastAction=showProduct&locale=de&

MSI K8N Neo2 Platinum, Socket 939, nVIDIA nForce3 Ultra Chipset w/ 8X AGP (ATX)

MSI K8N Neo2 Platinum, Socket 939, nVIDIA® nForce3 Ultra Chipset w/ 8X AGP (ATX)
and a 3500 90 nm amd 64.........is this a god combo ......Im swicthing mine for this(just the cpu and mobo) opions?..........any help is welcome...Its in the name of gamging...

Quote from: duffyone on 31-March-05, 11:54:15
Now... don't LOL, but there is a reason I picked the 3200+ instead of the 3000+, but I can't remember why???
Probably because the 3000+ only has a 9x maximum multiplier, whereas the 3200+ will go to 10x.
2600MHz at 9x means a FSB of 289MHz and ram at 289MHz for best performance. Will your ram do 289MHz? Of course you *can* run your memory and fsb async, but I prefer not to.
Chip

System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

System specs are
COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
ATI Radeon X800XT PE AGP
SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
LITEON 16X DVD-ROM INT E-IDE RETAIl
MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
LG 4163b dvd burner
Nothing has ever been overclocked on this system.
Everything is plugged into a Belkin Surgemaster powerbar.
I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
CPU fan won't even spin. Nothing happens.
O.k., blown power supply, I think . . . .
So I take out my Antec and put it in another system. That system turns on
without any problems.
Hmm . . .
I come here, and I read posts about
potential compatibility issues with Antec power supplies. But if it's a compatibility
issue why was my system working for about a year?
O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
I just plug it into the mainboard (nothing else). Hit the power button . . .
The CPU fan spins for half a second, and then nothing.
Did my motherboard just suddenly die for no reason?
Any suggestions?

Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
Then try to post the system barebone .
Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
It could also be caused by a short or a malfunctioning fan connected to mobo.
Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
The chipset fan can also be disconnected momentarily just to see if it posts.
If none of this helps , replace cmos battery and try again .

PC Perspective #1 Leaderboard entry MSI K8N Neo2 Platinum nForce3 Ultra

PC Perspective...ala AMDMB.com has the top to rated pc builds using the MSI K8N Neo2 Platinum nForce3 Ultra.
Whooohooo
PC Perspective
I like Ryan's picks. By the way AMDMB does rock...fantastic forums great info on mobo's not just AMD either.

HI! i'm the one wih the raid problem on a k8n neo2....
That's what a i Did.. i unpacked the exe and copy the files in a floppy... question is: if i do that, windows instaler askme for some files that aren't in the .exe, anway it reconices the raid and everithing goes fine until the first BOOT on windos... it shows a blue screen, butremoves it so fast that i cant read it or pause the system. But i know it's a raid problem because if i install it on a ide disk it works.
The nforce3 drivers are almost a year old, and i'm not sure if nforce4 is compatible...
I think the're compatible because if you enter in msi driver download page and select my model, they put the Nforce3 and nforce4 for win64 and my model is only nforce3. The thing is they havent released the nforce3 for WIN 64.... So.. It's normal that win asks me for some files that ain't in the .zip file (i extracted the files o course) and Which driver should i put the Nvidia one year old nforce3 or the new nforce4. (the nforce3 for 32 bits is rejected by windows) or... i have to wait the new nforce3?
thanks for helps

K8N Neo2 Platinum NB Temp

Does anyone know what the safest max temp is for the NB? I'm running an HTPC and noise is a factor. Using Fan Speed at 100% (CPU & NB) and Prime95, my temps were CPU 45 - NB 34. At livingroom noise levels (fans at 40%) Temps were CPU 48 - NB 40.
Thanks,
P
K8N Neo2 Platinum
AMD Athlon64 3000+ Venice - No O.C.
Zalman 7000Cu HSF
Seasonic S-12 380w PSU

Quote from: kakarocht on 09-September-05, 13:16:22
The max temp is bout 70-75C.
I think that maybe okay for CPU but NB chip is probably lower (about 50c max). Mine goes to around 40c with OC of HTT to 1060mhz.
If you do not OC then you could consider a Zalman passive NB cooler (if you have decent airflow in your case) but beware that the chip is very close to the AGP slot and may block longer cards (eg. 6800GT).

4x512 Dimms @ 400DDR @ 1T on K8N Neo2 Platinum NForce3...

just wondering if someone here managed to get 4x512 Megs Dimms @ 400mhz @ 1T on K8N Neo2 Platinum NForce3 running on a64 3000+ Venice flawlessly...
Thank you in advance

Quote from: bejon2000 on 25-October-05, 19:40:25
The enhanced Venice core basically made it possible to run 4x512 at DDR400 speed ( used to be 333mhz for some early cores ).
I´ve ordered a new 146 Opteron for socket 939 and it will be interesting to see if these "quality" cores handle RAM the same way as Venice or if they do it in a better way.
Be sure to post your findings when you install your spanking new Opteron

USB Keyboard (K8N Neo2 platinum)

motherboard k8n neo2 platinum, somehow my motherboard does not recog my usb keyboard. i have gone to bios and enabled USB mouse/keyboard , my mouse is ok no matter which usb front or back but the keyboard usb does not work on any of usb . does anyone have any idea (hardly used keyboard, nearly new) all usb are ok??. your help will be much appreciated.
1-Motherboard MSI 7025 K8N Neo2 Platinum Chipset nForce3-250Gb/Ultra
2-CPU AMD Athlon Dual Core 3800X2
3- Graphic card (MSI FX5700) nVIDIA GeForce FX 5700
4-Memory 2 X1 GB DDR 400 DIMM kingston
5-HDD Maxtor 6Y160M0 (160 GB, 7200 RPM, SATA
6- OS Window XP Prof sp2
7-power supply Be Quite BQT- P5-420W

Bosskiller thanks for the reply it is a micorisoft multimedia, yes i have tried the back usb no luck there either. here is the link for the keyboard
http://www.farassoo.com/product/keyboard/fcr-8800.htm
but i wonder if you can tell me why some system their front usb doesn't work with usb keyboard a few have said this to me. many thanks

News - BIG PROBLEM - MSI K8N Neo2 Platinum - DOES NOT POWER!!!

Hi to everyone.
I'm a proudly owner of a MSI K8N Neo2 Platinum that in one year gave me no problem until yesterday morning.
I used the computer in the night before and when I finished I turned it off and I went to bed.
Yesterday morning I found the power led blinking (like if the system was in standby), and there was no way to turn the PC on.
I even took off the battery for more than 12 hours and I left only minimal components installed:
the video card (Gainward GeForce 6800),
the psu (Antec TruePower 550W),
1 x 512 MB Ram Crucial Ballistix,
and I checked them into another computer and they work perfectly.
I tried shorting the MB power switch pins with a screwdriver and I've even tried to power on the system without the Memory or the Video Card... I've tried everything that came across my mind with no efforts!!!!
Every time I give power to the MB appens only that the power led starts blinking, but pressing the button the PC doesn't turn on.
PLEASE HELP ME... I really don't know what else to do!!!
Thanks,
Alberto

Quote from: alberto_melita on 20-August-05, 20:14:56
Hi thanks for the answers.
I do have a D-Bracket, but my problem is not that the system does not boot or does not post... my system DOES NOT POWER ON (!!!!), so d-bracket is useless!
When I plug the system power the only thing that happens is that the power led starts blinking (with the system still in soft-off), and if I press the power switch button nothing happens!
I've the bios for 7025 v1.8 and the settings where for OFF on power-loss ond pressing the button (can't rememeber if it was more than 4 sec) was meant to turn off the computer, but considering that I un-powered the pc more than once without the MB battery the settings should be factory default by now.
I went through the Windows-XP shut-down system, and i could not be an electrical problem as I always used the PC with a pretty good UPS unit.
Right now these are the full specs of my sytem:
- MB MSI K8N Neo2 Platinum nForce3 Ultra
- GAINWARD 6800 2600 GLH 256 MB Ram
- PSU Antec TruPower 550 W
- CPU AMD64 3500+ core Winchester @11*210 Mhz (this cpu has never overclocked very well)
- HEATSINK Thermalright XP-90 with a 12 Cm Enermax Fan (CPU temp in always below 55 °C when stressed)
- 1 x 512 Mb RAM Crucial Ballistix DDR400 optimized for MSI K8N Neo2 Platinum
I left only these things inside my computer in the hope that it would turn on... it did not work. I tested each component but the MB, and they work perfectly.
Again...
Thanks for you efforts, any help will be appreciated.
Alberto.
All parts have been tested: CPU/RAM/GFX/PSU/HD/DVD, just not the MOBO ?
Checked if the MOBO is shorting in the case ?
Have you tried using the reset switch as power, on/off switch ? I've seen before when the power switch stops working (lose/bad wire busted spring) after swapping reset to power, then the system turned on. Worth a try, as sending it back to USA won't be cheap. If its over 1 year old it mite not be covered by the re-seller and or MSI. Best to check this out as law and warranty is different from country to country.
Good Luck

K8N NEO2 Platinum rebooting

Hi all,just got myself a 64bit MSI K8N NEO2 Platinum board & a 3200+,am happy with it but a couple of days ago i got a blue screen with a long message that i didnt have time to read before the pc rebooted,after the reboot i checked the event viewer log file in administrative tools/control panel but couldnt narrow it down as my particular error code wasnt among the possible causes.
Among some of the possible causes were incorrectly installed USB drivers or the BIOS,i downloaded the latest BIOS update before this problem started(V1.40) which i am using now,i used the MSI live update software to flash it which i did in windows mode.Sorry for prattling on!well it did it again tonight and i managed to read a bit of the writing on the blue screen which mentioned flashing the bios to the latest version.I was wondering if anyone else is having the same problem and if so could you please advise me? Thanks for your patience and any help Heres my sys specs:
Model: AMD Athlon(tm) 64 Processor 3200+
Speed: 2.01GHz
Model Number: 3200 (estimated)
Performance Rating: PR3015 (estimated)
Type: Standard
L2 On-board Cache: 512kB ECC Synchronous Write-Back (16-way, 64
byte line size)
Bus(es): ISA AGP PCI USB FireWire/1394
MP Support: 1 CPU(s)
MP APIC: No
System BIOS: Phoenix Technologies, LTD 6.00 PG
Mainboard: MS-7025
Total Memory: 1023MB DDR-SDRAM
Model: Micro-Star International Co Ltd (MSI) ???
(00E1)
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Model: Advanced Micro Devices (AMD) Athlon 64 /
Opteron HyperTransport Technology
Configuration
Front Side Bus Speed: 1x 201MHz (201MHz data rate)
Total Memory: 2048MB DDR-SDRAM
Memory Bus Speed: 2x 201MHz (402MHz data rate)
Monitor/Panel: CTX EX950F series
Adapter: RADEON X800 Series
Adapter: RADEON X800 Series Secondary
Removable Drive: Floppy disk drive
Hard Disk: Maxtor 6Y080L0
CD-ROM/DVD: HL-DT-ST DVDRAM GSA-4081B (CD 32X Rd, 24X Wr)
(DVD 4X Rd, 3X Wr)
CD-ROM/DVD: MSI CD-RW CR52 (CD 40X Rd, 52X Wr)
CD-ROM/DVD: AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd)
(DVD 4X Rd)
1.44MB 3.5" (A:): N/A
Hard drive (C:): 76.3GB (51.9GB, 68% Free) (NTFS)
CD-ROM/DVD (D:): N/A
CD-ROM/DVD (E:): N/A
CD-ROM/DVD (F:): N/A
Serial/Parallel Port(s): 1 COM / 1 LPT
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard OpenHCD USB Host Controller
USB Controller/Hub: Standard Enhanced PCI to USB Host Controller
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
USB Controller/Hub: USB Root Hub
FireWire/1394 Controller/Hub: VIA OHCI Compliant IEEE 1394 Host Controller
Keyboard: Standard 101/102-Key or Microsoft Natural PS/
2 Keyboard
Mouse: PS/2 Compatible Mouse
Device: Creative SB Live! series
Device: Creative Game Port
Model: EPSON Stylus CX3200
Windows System: Microsoft Windows XP/2002 Home (Win32 x86)
5.01.2600 (Service Pack 2)
Network Drivers Enabled: Yes
Warning 100: Large memory sizes should be made of
Registered/Buffered memory.
Tip 101: Large memory sizes should be made of ECC/
Parity memory.
>
>
Device Type: VGA Video Adapter
Device ID: bus 1, device 0, function 0
Windows Device Name: RADEON X800 Series
OEM Device Name: ATI Technologies ??? (4A49)
OEM Hardware ID: FUN_0, VEN_1002, DEV_4A49, REV_00
Device Name: PC Partner Ltd ??? (4A49)
Product ID: VEN_174B, DEV_0D42
Revision: A / 1 (0)
Version: 3.00
Command Queue Length: 256
Fast-Writes Support: Yes
Over 4GB Addressing Support: No
Isochronous Mode Support: No
Addressing Support: 32-bit
Data Transfer Modes Support: 4x 8x

My K8N Neo Platinum [754] did not include a NB fan. But this usually means the overall size of the heatsink is larger. If you remove the fan from yours, the size of the heatsink will not be big enough to cool your NB. As for temps, I've never seen my NB get hotter than 45'C. Note that the core on my NB should be slightly different than yours.
You could try to use the BIOS fan control for the NB. If set correctly, it should reduce some noise.

Need help with k8n neo2 platinum

I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
I have bios revision 1.5.
Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
PS I've tried reducing the htt to 3x but the same thing happens.

OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

Hi-
I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
Single SATA or Multiple Drive Array Setup FAQ
I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
- Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
- Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
- I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
- Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
Any help would be appreciated.
- the bbdude

OK Thanks JeanGuy and ssjkakaroto,
I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
- I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
- As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
Thanks -
- bbdude

NForce3 chipset temp on K8N Neo2 Platinum

Similar Messages

Maybe you are looking for