No connection to server via LAN

When I say
_nc:NetConnection = new NetConnection();
_nc.connect( "rtmp://127.0.0.1/ImmuneDefense" );
It works
Now I want to let another computer in the local network connect to the server.
_nc.connect( "rtmp://192.168.0.9/ImmuneDefense" );
It doesnt work. No connection.
No firewall. All gates are open. Please help. I spent already many hours in searching for a solution.

Can you connect to the internet and get webpage data at websites such Google.com (or otherwise)? Is it ONLY affecting your email? If so, which email accounts? If they are Outlook/Hotmail, there is an ongoing issue with the service for some users.

Similar Messages

  • Can I connect a PC via LAN to my WLAN - connected time capsule?

    Hi,
    I haven't found any info on this in the forums yet:
    The problem:
    My WLAN - router is located in my living room and has loads of devices connected (iPhone, iPad, 2 Zeppelin Air, MacBook Air, some other Win - PCs etc...)
    One of the PCs (Win 7) is in another room, connected via WLAN too.
    I now have a time capsule near this PC and would like to connect these two via LAN and then use the WLAN connection of the time capsule for this PC too.
    After connecting the Ethernet cable (which was working fine elsewhere) I see that there is a connection, but no access to the network.
    Any suggestions would be highly appreciated.

    You likely have the Time Capsule configured to "Join a wireless network". Is that correct?
    If yes, the Time Capsule does not perform any routing functions in this type of configuration. In effect, it has become a wireless hard drive.
    Therefore, the Etherent ports are not enabled, so there is no signal available at the ports.

  • Airport express connect with Imac via lan line or can not?

    I using IMac with connect to internet with DSL modem router (having 4 lan ports).
    Now I put Airport express connect with one of Lan ports from DSL router and still connect my IMac with DSL router via lan line and still connect to internet via lan line (switch off airport function in Imac).
    The Airport express is using for provide wireless internet and printer to my other PC.
    My Question is can I still set up as above and connect share file to my PC via airport express?
    Forget to tell that I'm very newby to mac.

    chounws, Welcome to the discussion area!
    Yes you can do that. Configure the AirPort Express (AX) to operate in bridge mode (not sharing a single IP address).

  • Facing error while connecting to server via XWinlogon

    Hi experts,
    I am facing issue
    "Fatal server error:
    could not open default font 'fixed'"
    While connecting to server via XWinlogon, i am installing EBS 12.1.1 on server.
    Please suggest appropriate values of xwinlogon, i am new for xwinlogon.
    its urgent , waiting for reply.
    Thanks,

    Hi;
    Did you go wiht VNC? If no please go wiht it. If you have to use xwin than please see <a href=http://www.google.com.tr/#hl=tr&sclient=psy-ab&q=could+not+open+default+font+%27fixed%27%2Bxwinlogon&oq=could+not+open+default+font+%27fixed%27%2Bxwinlogon&aq=f&aqi=&aql=&gs_sm=3&gs_upl=6125l6937l1l7187l3l3l0l0l0l0l187l484l0.3l3l0&gs_l=hp.3...6125l6937l1l7187l3l3l0l0l0l0l187l484l0j3l3l0.frgbld.&pbx=1&bav=on.2,or.r_gc.r_pw.r_qf.,cf.osb&fp=6202e7794537e514&biw=1196&bih=561
    this serch</a>Regard
    Helios

  • Can't connect to server via apple+k

    If i try and connect to another machine via GO>CONNECT TO SERVER I get the beachball of death which spins forever until I force quit finder.
    I have created a new user account and if i try the same it works perfectly, which suggests to me a file/preference has corrupted.
    Does anybody have an idea what files may be corrupt and need deleting?
    Thank you

    Managed to sort it myself.
    Moved the Library folder from 'Username'>Library onto my desktop and logged out of the dodgy account.
    Logged in again and a new Library folder was created. Apple+k then worked.
    I then copied the old files into the new folder in batches of 20, logged out then in again and kept trying Apple+k.
    I put all the files back,logging out then in every time, ensuring the file I was copying overwrote the new file.
    After I had copied all the files I rebooted and upon restart Apple+k worked.
    I have no idea what the actual corrupt file was, but at least other people with the same problem now have a method of getting back to normal.

  • Since updating to Leopard can't connect to server via internet

    Since updating our server to Leopard I haven't been able to connect to it via the internet from home. Any ideas? Says verification failed when I try to re-add it. Ports 3283 and 5900 are open at both ends.
    Edit: I just managed to access it using the root account. Any ideas why it's not working with the other admin accounts via the internet (they work when I'm local)?

    It appears that the adding a user to the "allow access for" list corresponds to adding group membership, in the group "com.apple.access_ssh".
    So, one way of brute-forcing a user into this list would be to add it to the group. One way of doing this at the command-line:
    sudo dscl . append /Groups/com.apple.access_ssh GroupMembership whatever-my-admin-account-is-called
    This will require a password and only work for people with sudo permission, natch.
    CAVEATS:
    1) I have no idea what you mean when you say "local" users. What distinguishes the "local" users from the others?
    2) I do not know where the OS stores the information about whether or not the "All Users" radio button is checked. I just checked to see whether checking this box adds all users to the com.apple.access_ssh group, and I confirmed that it does not.
    Message was edited by: John Clements

  • IMessage, can't connect to server via id

    Hi
    For several days now I try to connect to iMessages from my MacAir. Each time I try to log-on via my apple-id I get an error message stating that there is a server issue and I should try later. I'm well able to connect to iMessages via my iPad. Any thoughts?
    Thanks

    I think something is up at apple.
    I'm still not able to connect to iMessages via my MA. Although I have the correct password I tried to change it via iMessages which directs me to iforgot.apple.com. If I chose to change it via my email address I do not get an email with the corresponding link to do so. It is not in the spam either.
    Nobody experiences the same problem?

  • Cannot connect to server via hostname

    When I ping this server, it replies with the correct IP address. However, if I want to RDP to it, I can only do it by IP and not hostname.
    If I go by hostname, it returns this error:
    "Remote Desktop cannot verify the identity of the remote computer because there is a time or date difference between your computer and the remote computer. Make sure your computer's clock is set to the correct time, and then try connecting again. If
    the problem occurs again, contact your network administrator or the owner of the remote computer."
    I verified that there is no date or time difference, which I doubt would be the cause of the problem anyway since I'm able to RDP to that server via IP address just fine.
    I found this article:
    http://andywolf.com/windows-2008-r2-server-loses-network-connectivity/#comments
    It details the same symptoms, except the fact that it says they ran this command:
    netsh trace start scenario=netconnection capture=yes report=yes tracefile=c:\net.etl
    And it said that they discovered kernel socket leaks as a result. I did not find anything that indicated kernel socket leaks.
    any ideas?

    Hi
    You need to run couple of test to make sure the host name is resolving to the correct IP.
    Form another working machine run nslookup and put this computer hostname then hostname with FQDN and make sure it is returning the correct IP.
    If its not then try clearing cache on the local machine form cmd with ipconfig /flushdns and on you DNS server with dnscmd /clearcache. Try again to resolve the hostname if still the same.
    Check in the DNS console and make sure this host got the correct IP address assigned to it if not delete the record and release and renew the IP if you are using dynamic IP. If you are using static then ipconfig /registerdns.
    It could be the DNS suffix issue.
    Please update with the above.

  • Slow RD connection to server via RD Gatway if NLA is disabled on the server

    If I disable NLA on a server (tried on 2 different servers), the rd connection (via gateway only) is much slower (over 1 min to get to the logon screen).
    RD Gateways are 2012R2, hosts are 2012 and 2012 R2.
    Re-enabling NLA fixes the issue. Any ideas?
    Dario Palermo

    Hi Dario,
    Putting the gatewayusagemethod:i:1 in the .rdp file will force the RD Client to use the gateway always and thus speed up the connection time. When connecting from the Internet, as a test, please uncheck Bypass RD Gateway server for local addresses in the RD
    Client options--Advanced tab--RD Gateway settings.
    Please try “Require user authentication for remote connections by using Network Level Authentication” policy setting under below path.
    Computer Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Security
    Configure Network Level Authentication for Remote Desktop Services Connections
    https://technet.microsoft.com/en-us/library/cc732713.aspx
    Addition you can check for “Network security: LAN Manager authentication level”
    https://technet.microsoft.com/en-us/library/cc738867(v=ws.10).aspx
    Hope it helps!
    Thanks.
    Dharmesh Solanki
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Satellite Pro P100 - Can't connect to Internet via LAN

    I have a Toshiba Satellite Pro P100. Model No SPSA4A-005002
    I used my recovery disk and wiped my computer, because of a virus and now I cant connect to the internet via cable but my wireless internet works perfectly.
    Its completely dead there are no lights at the back of the laptop from where I plug the cable in.

    Hi
    Is your LAN card recognized properly in device manager?
    In your case I would try updating the LAN driver. You can get the latest version here:
    http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
    Furthermore you check the BIOS version. The latest version should be installed and load the default settings there.
    In worst case its a hardware problem and you have to exchange the whole mainboard :(

  • Connection to server via smb not working

    hi,
    i have an old G4 iBook 10.3.9 that i'm using for school. to connect to our school server for course material, we were given smb log-in instructions from our it dept. when i put in the ip address, i get a prompt for the id and password, but i cannot get access. we tried logging on with my professor's macbook pro (10.5) and it worked flawlessly.
    i've done all software updates and rechecked the procedure dozens of times, but i can't figure out why it's not working. if anyone has an idea, i'm all ears.
    thanks,

    created in my UTF-8 Mysql DB your table and inserted a record; the select shows:
    SQL> select * from "movieclass"@mysql;
    idClass
    ClassName
    123
    H e l l o
    As you can see the content is there, the "space" between the letters is related to unicode. Each character is interpreted by 2 bytes and SQL*Plus wrongly displays both. Using iSQLPLus or SQLDeveloper does not show the "space" between the letters.
    Here the data type mapping:
    SQL> desc "movieclass"@mysql;
    Name Null? Type
    idClass NUMBER(3)
    ClassName NOT NULL NVARCHAR2(50)
    What's the exact version of DG4ODBC you're using? 11.1.0.7?
    According to the listener file you're using DG4ODBC on Windows. There was a high/low byte issue in DG4ODBC for Windows. This issue is fixed in 11.1.0.7 and a certain patch. So I recommend you to get first the 11.1.0.7 patchset (if you don't already have it installed):
    6890831 Oracle Database Family: Patchset
    11.1.0.7.0 PATCH SET FOR ORACLE DATABASE SERVER 11.1.0.7.0
    and then please apply also the latest patch:
    8689191 Oracle Database Family: Patch
    ORACLE 11G 11.1.0.7 PATCH 16 BUG FOR WINDOWS 32 BIT 11.1.0.7.0
    There was a high/low byte issue
    Edited by: kgronau on Aug 11, 2009 10:28 AM

  • Connect to Server via SMB does not work under 10.5

    Hi- I have a feeling that my account has to be reset server-side, but I'd enjoy some feedback. I still use a dual (1gHz) Quicksilver G4 which is solid as a rock and still adequate to my needs. Apart from an overall seeming sluggishness, I have a very serious problem: I am one of 7 Macs on a much larger Windows network and connecting to the various servers and directly to my Windows desktop using SMB has always worked great. Up until yesterday. After upgrading to 10.5 from 10.4.10, I couldn't get on to any of the servers, I checked the network setting and noted that they reverted to AFP. I enabled SMB and still can't get onto any of our network servers. I am, however, able to get into the Mac Public\Drop Box from the WIndows computer, but not vice-versa. I have already verified and repaired permissions, etc. Solutions, suggestions? Patch forthcoming?

    Same problem with my Nokia 6650d, also after Ovi upgrade. Any hints?

  • Manually connecting POP server via telnet command

    How do I manually telnet to my POP (Post Office Protocol) server to check
    if my mail server is accepting connections?
    <P>
    This method of manually connecting to the mail server is sometimes
    necessary in order to help better troubleshoot Messaging/Mail issues.
    By directly telneting to the POP server, you can determine if the problem is
    within the client software or the server. Following is a list of commands to be
    executed from the UNIX command line or DOS shell using the telnet utility:
    <P>
    Telnetting to port 110 (the POP port).
    telnet machine 110
    POP commands:
    USER uid Log in as "uid"
    PASS password Substitue "password" for your actual password
    STAT List number of messages, total mailbox size
    LIST List messages and sizes
    RETR n Show message n
    DELE n Mark message n for deletion
    RSET Undo any changes
    QUIT Logout (expunges messages if no RSET)
    More commands (and the entire spec) are available at
    http://www.imc.org/rfc1939.

    Hi Helmut,
    I am not sure about the command line client. However you can check-in the activities of other users using the process below:
    1. Login to this URL http://hots:port/dtr/system-tools/reports/ActivityQuery
    2. The user id should have administrator's right.
    3. On the selection screen enter the user who's activities you want to check-in.
    4. Select one of the activity that is listed by clicking on it.
    5. On the page towards the top right hand corner you will have the drop down with one option to check-in the activity. This is only available to admin user.
    Hope this helps.
    Regards
    Sidharth
    Message was edited by: Sidharth Deshpande

  • I cant connect ti server via resource central panel

    I got this error pop-up
    " We're sorry, but there was an error communicating with the server. Please try again and if the problem persists, contact Adobe Technical Support. (503) "
    I have tried to enter http://resourcecentraldl.adobe.com/
    and get
    "Forbidden
    You don't have permission to access / on this server."
    that mean I can connect to the server
    I already close my firewall but it's still can't connect
    What should I do?
    Help me pleaseeeee
    Thanks :)

    Arinchy,
    A config file have been included in version 4.0.0 that points to an internal server that is inaccessible from outside the Adobe firewall. You should be able to quickly solve the problem by opening Windows Explorer and navigating to:
    C:\Program Files\Adobe\Adobe Premiere Pro CS4\ResourceCentral
    Then rename the file config.xml to config.BAK or something similar. Launch Premiere again.
    You can also update to 4.0.1 where the issue is resolved.
    René

  • Cannot connect to server via management studio

    Hello,
    I've installed Express with Tools 64bit edition. EDIT: it's 2014 version, here's the download link https://msdn.microsoft.com/en-gb/evalcenter/dn434042.aspx?f=255&MSPPError=-2147217396 
    But when I try to connect to the database using the management studio, I get this error:
    Signature for the declaration in a method implementation cannot be found.  Type: 'Microsoft.SqlServer.Management.Smo.SqlSmoObject'.  Assembly: 'Microsoft.SqlServer.Smo, Version=12.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91'. (Microsoft.SqlServer.Management.SqlStudio.Explorer)
    Program Location:
       at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.CheckAndEnableSmoXps(SqlConnection connection, Boolean smoXpsEnabled)
       at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.CheckDacAndSmo(SqlConnection sqlConnection)
       at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server)
       at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser()
    I don't get what this error is trying to tell me really. Hopefully someone can explain it so I might fix it. Or any information why I can't seem to connect would be appreciated.
    I've tried connecting to a running server instance, and I've tried connecting to localdb; both gave the same error. The name seems right, as a different error appears when it cannot find the server/bad name.
    I was able to connect with visual studio 2013 and create a new database through that, so this feels a bit like a missing dependency or something in my management studio installation. I ran installation repair, but it didn't find any problems.
    I'm looking to learn SQL so it's possible the setup of the server was not done right, maybe? But I'm not sure if that would affect localdb... guess it's pretty clear that I'm at a loss why it's not working; hopefully someone will be able to help.
    Beginner

    Hello,
    Could you try to apply the following update for SQL Server and apply the latest update for VS 2013?
    https://support.microsoft.com/en-us/kb/3031047/en-us
    Another option may be repairing the installation.
    https://technet.microsoft.com/en-us/library/cc646006(v=sql.120).aspx
    Hope this helps.
    Regards,
    Alberto Morillo
    SQLCoffee.com

Maybe you are looking for