Nokia C3-01 wlan is connecting but unable to brows...
Hi ,
I bought Nokia C3-01 touch and type model 5 days before, I connected it through the wlan and it was successfully connected, but once i started browsing it show the msg after loading for few min as " the link is not found plz try after some times' ,but the page is opening while using gprs, plz help me to resolve the problem.
I got Wifi working finally for Opera Mini on my Nokia C3-01 phone. It was working fine for browser and mail application though.
I did the following.
1) In Settings >> Configuration >> Def. config. sett.
Delete all entries.
2) Create a access point manually using Settings >> Configuration>>Personal Settings.
It is necessary to create one. It will still work even though it is not pointing to real access point. Just point it to dummy Pack. data acc. pt. access point say "foo".
3) Set the access point created in step 2 as Preferred acc. pt using Settings >> Configuration>>Preferred acc. pt
4) Make sure you had set WLAN >> Internet Conn. to Ask first.
Now apps like Opera Mini starts Asking for Access point whenever connecting to internet.
It shows mutiple access point in the list. Usually the first one is your wifi access point and second one is the dummy access point you had as preferred access point.
Using the above steps i am able to point wifi access point to access internet in all apps available in my phone. If you want to still access your gprs access point too then point the preferred access point created in step 2 to real gprs access point instead of "foo". Contact your operator to get configuration details for real gprs access point or check out how it is configured in your friends phone using the same operator as yours. Just make sure you are doing it manually and are not using the configuration profile sent by operator direcly to your phone. It blocks wifi access point access on your phone.
My phone details are as follows:
Nokia C3-01
v 05.65
26-11-10
RM-640
(C) Nokia MR1
My operator:
Vodafone IN
The moral of the story is configure your access point manually.
Do not use configuration setting provided by operator, they block access to wifi access point.
I dropped configuration settings provided by my operator i.e Vodafone IN when i found that apps like opera mini are always connecting to gprs instead of wifi.
Similar Messages
-
E62 though connected but unable to get browsing
I got Nokia E62.
I have connected this phone through USB Cable with Modem.
All got successfully done and connected but unable to browse on phone.
Is there any setting to be done on phone to get start browsing?
Can anyone try to send suggetion?
Attachments:
E62-3.JPG 99 KB
E62-1.jpg 147 KBHi there.
Some hotel networks require some sort of authentication, or sometimes even payment to connect to the network. If you are connected to the wireless network, and the network requires this, you should be greeted with a page as every time that you attempt to connect to a wireless network, the iPad checks for this.
I would also try contacting the hotel's network troubleshooting department for help also, as they may have a different configuration than normal networks do.
Hope this helps. -
VPN connects but unable to access resources on remote network
HI,
I'm able to ping the ASA interface once the VPN is connected but unable to access any of the resources located on the remote network such as shares and computers. The cisco vpn client shows data being sent and recieved when I ping the interface on the ASA but it doesn't recieve any data when I attempt to ping or access other resources on the network.
ASA Version 8.2(5)
hostname HOST_NAME
domain-name default.domain.invalid
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
speed 10
duplex half
interface Ethernet0/4
speed 100
duplex full
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.10.8.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 12.x.x.x x.x.x.x
boot system disk0:/asa825-k8.bin
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 10.10.8.2
domain-name default.domain.invalid
same-security-traffic permit intra-interface
object-group service Vipre tcp
port-object range 18082 18082
port-object range 18086 18086
object-group network town
network-object 192.168.0.0 255.255.0.0
access-list outside_20_cryptomap extended permit ip 10.10.8.0 255.255.255.0 192.168.0.0 255.255.252.0
access-list new extended permit ip host 192.168.0.1 any
access-list new extended permit ip any host 192.168.0.1
access-list outside_20_cryptomap_1 extended permit ip 10.10.8.0 255.255.255.0 192.168.0.0 255.255.252.0
access-list townoffice_splitTunnelAcl standard permit 10.10.8.0 255.255.255.0
access-list townremote_splitTunnelAcl standard permit 10.10.8.0 255.255.255.0
access-list outside_access_in extended permit tcp any interface outside object-group Vipre
access-list outside_access_in extended permit tcp any object-group Vipre interface inside object-group Vipre
access-list outside_access_in extended permit tcp any eq 3389 10.10.8.0 255.255.255.0 eq 3389
access-list test extended permit ip host 192.168.0.6 host 10.10.8.155
access-list test extended permit ip host 10.10.8.155 host 192.168.0.6
access-list test extended permit ip host 10.10.8.2 host 192.168.3.116
access-list test extended permit ip host 192.168.3.116 host 10.10.8.2
access-list test extended permit ip host 10.10.8.155 host 192.168.3.116
access-list bypass extended permit ip host 10.10.8.155 host 192.168.3.116
access-list bypass extended permit tcp 192.168.0.0 255.255.0.0 10.10.8.0 255.255.255.0
access-list bypass extended permit tcp 10.10.8.0 255.255.255.0 192.168.0.0 255.255.0.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn 10.10.8.125-10.10.8.149 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (inside) 1 interface
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.0.0
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 18082 10.10.8.2 18082 netmask 255.255.255.255
static (inside,outside) tcp interface 18086 10.10.8.2 18086 netmask 255.255.255.255
static (inside,outside) tcp interface 3389 10.10.8.2 3389 netmask 255.255.255.255
static (inside,inside) 192.168.0.0 192.168.0.0 netmask 255.255.0.0
static (inside,inside) 10.10.8.0 10.10.8.0 netmask 255.255.255.0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 12.70.119.65 1
route inside 192.168.0.0 255.255.0.0 10.10.8.250 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
http server enable
http outside
http outside
http inside
http outside
http inside
http outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt noproxyarp inside
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 60 set pfs
crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 80 set pfs
crypto dynamic-map outside_dyn_map 80 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 100 set pfs
crypto dynamic-map outside_dyn_map 100 set transform-set ESP-3DES-SHA
crypto map outside_map 20 match address outside_20_cryptomap_1
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer 69.87.150.118
crypto map outside_map 20 set transform-set ESP-3DES-SHA ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp nat-traversal 30
telnet 10.10.8.0 255.255.255.0 inside
telnet timeout 5
ssh 63.161.207.0 255.255.255.0 outside
ssh timeout 5
console timeout 0
dhcpd dns 10.8.8.2
dhcpd address 10.10.8.150-10.10.8.200 inside
dhcpd dns 10.10.8.2 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy aaa internal
group-policy aaa attributes
dns-server value 10.10.8.2 4.2.2.2
vpn-tunnel-protocol IPSec
default-domain value domainname
group-policy bbb internal
group-policy bbb attributes
wins-server value 10.10.8.2
dns-server value 10.10.8.2
vpn-tunnel-protocol IPSec l2tp-ipsec
split-tunnel-policy tunnelall
split-tunnel-network-list value townoffice_splitTunnelAcl
default-domain value domainname.local
group-policy townremote internal
group-policy townremote attributes
wins-server value 10.10.8.2
dns-server value 10.10.8.2 4.2.2.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value townremote_splitTunnelAcl
default-domain value domainanme
group-policy remote internal
group-policy remote attributes
wins-server value 10.10.8.2
dns-server value 10.10.8.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value townremote_splitTunnelAcl
default-domain value dksecurity.local
address-pools value vpn
username xxxx password . encrypted privilege 15
username xxxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxxx password . encrypted privilege 15
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx password encrypted privilege 15
username xxxx attributes
vpn-group-policy remote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy remote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy remote
username xxxx password encrypted privilege 15
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy remote
tunnel-group 69.87.150.118 type ipsec-l2l
tunnel-group 69.87.150.118 ipsec-attributes
pre-shared-key *****
tunnel-group remote type remote-access
tunnel-group remote general-attributes
address-pool vpn
default-group-policy townremote
tunnel-group townremote ipsec-attributes
pre-shared-key *****
isakmp keepalive disable
tunnel-group townremote type remote-access
tunnel-group townremote general-attributes
address-pool vpn
default-group-policy townremote
tunnel-group lansingremote ipsec-attributes
pre-shared-key *****
class-map tcp-bypass
match access-list bypass
class-map test
match access-list new
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
no dns-guard
no protocol-enforcement
no nat-rewrite
policy-map global_policy
class test
class inspection_default
policy-map tcp
class tcp-bypass
set connection random-sequence-number disable
set connection advanced-options tcp-state-bypass
service-policy global_policy global
service-policy tcp interface inside
prompt hostname context
call-home reporting anonymous prompt 2
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:c724d6744097760d94a7dcc79c39568a
: endYou need to change the VPN pool ip subnet to something other than the same ip range used on the inside interface.
Sent from Cisco Technical Support iPad App -
E63 Wlan not connected - but connected??
Hello,
I just updated my E63 to the newest software version (200.21.012 ) and im experiencing issues with the WLAN...
When i connect first time to a WLAN access point, it doesnt work, but then after disconnecting, the icon is still there. Under the connection manager list, there is no active connection, but i cannot use any internet based applications because it says i am already connected. Any help?
ThanksAnother program is still using the connection. Like Facebook, Nokia Messaging, Mail for Exchange, etc........ Press the home button for a few seconds to see whitch apps are active.
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009 -
Airport remaining connected but unable to load pages
I've been using my MB for four years now and this problem has recently appeared over the last two days. The airport icon will show full bars but I will have no connection to the internet. If I power cycle the airport (menu turn off then back on) I can then continue to browse the web. This happens about every five minutes or so.
I do have other computers in my house that aren't having this problem. So I know it's something to do with my Macbook. I was going to do a reformat/reinstall but I wanted to see if there was a known solution here. It's almost as if the DNS service just stops working and needs to be reset...
Any solutions? Purchase a new card? Reinstall OS?
Thanks!Hi!
I am experiencing the same problem! And by the looks of it some other users are too!
My Macbook is one and a half years old and I never had problems with using WiFi. I am currently using BT wireless and during the day it keeps dropping now and then.. I end up restarting the machine as the status icon shows that its fully connected with my chosen connection but internet doesn't work. After restarting several times and deleting all joined wireless connections history, it eventually works. I am getting annoyed by this now. Also, as said by the douglobue rest of the machines are working fine on wireless its only my macbook. Any help please?
Thanks in advance! -
E71 - Nokia PC Suite - does not connect ? unable t...
I installed Nokia PC Suite (v7.1) on my PC's:
Connected Nokia E71 with USB-cable
(Mass Storage > Via Windows Explorer I can see the directories on the memory card of the E71)
Problem-1: Nokia PC Suite gives error: "unable to find device"
(while phone is unlocked, USB mode is not applicable)
Problem-2: Also Nokia Software Updater does not work (cannot find device)
Happens both on XP and Vista PC.
In other words... I can't access my E71 at all. Who knows a solution ?Hi, i just ran into the same problem with the "Device Not Found" I will give the steps for what fixed my problem.
Connect the phone to your computer via data cable. Select "Connect Pc to Web". Then, inside the folders run the installer.exe** and select Repair instead of Uninstall. Now your device should work like a charm.
**If the installer.exe interrupts you saying that the version installed on the computer is newer than what you are trying to install and exits itself, you will have to go to control panel to uninstall Nokia Pc Suite and reinstall it with the phone you plan on using so it will be the correct version. Even after you reinstall Nokia Pc Suite you may have to run the installer.exe a second time and select repair before it will work. I did anyways.
I hope this fixes your problems you are having. Also the reason it is hard to get tech support for stuff like this is because when you can connect your mobile internet to the pc you can use a lot of data because you have more access to things. Eventhough you may have an unlimited data plan most if not all companies will ban your phone possibly without notice if you use more data then they want you too. Also tethering, which is what we are all trying to do. Is illegal for most if not all phone companies. Always best to read the Terms and Conditions.
As far as the USB not beeping when connecting the cable. I didn't hear mine either but it worked but if yours isn't working try this: Start -> Right-Click Computer -> Properties -> Device Manager-> Check all USB devices to make sure they are working properly and you may need to reinstall them.
Please reply to let me know if anything worked. If it did please check solution button to allow other people to find my post. Thanks for any replys to my post. -
ASA5520 AnyConnect SSL VPN Connected but unable to ping my inside LAN
Hi there, please forgive if I have missed any forum protocols as this is my first post.
I am trying to configure Anyconnect SSL VPN. I am able to connect to the VPN on a laptop, witch is able to download the anyconnect client from the ASA. I am unable to ping any of my IP's that are on the inside of my ASA. Before posting here I have spent many hours on forums and watching videos on anyconnect SSL VPN creation and I am following it to the T but still no ping. Any help would be very much appreciated.
Inside 192.168.1.254/24
Outside dhcp
VPN Pool 192.168.250.1-50/24
Inside LAN 192.168.1.0/24
: Saved
ASA Version 8.4(4)1
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address dhcp setroute
interface GigabitEthernet0/1
nameif inside
security-level 99
ip address 192.168.1.254 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 99
ip address 192.168.100.1 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name dock.local
same-security-traffic permit inter-interface
object network inside-network-object
subnet 192.168.1.0 255.255.255.0
object network management-network-object
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.250.0_25
subnet 192.168.250.0 255.255.255.128
object-group network AllInside-networks
network-object object inside-network-object
network-object object management-network-object
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit icmp any any echo-reply
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
access-list split_tunnel standard permit 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpn_pool 192.168.250.1-192.168.250.100 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic AllInside-networks interface
nat (inside,any) source static any any destination static NETWORK_OBJ_192.168.250.0_25 NETWORK_OBJ_192.168.250.0_25 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable 4433
http 192.168.100.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 192.168.100.0 255.255.255.0 management
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_anyconnect internal
group-policy GroupPolicy_anyconnect attributes
wins-server none
dns-server value 8.8.8.8
vpn-tunnel-protocol ssl-client ssl-clientless
split-tunnel-policy tunnelall
split-tunnel-network-list value split_tunnel
default-domain value dock.local
username test password JAasdf434ey521ZCT encrypted privilege 15
tunnel-group anyconnect type remote-access
tunnel-group anyconnect general-attributes
address-pool vpn_pool
default-group-policy GroupPolicy_anyconnect
tunnel-group anyconnect webvpn-attributes
group-alias anyconnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http
https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email
[email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:24bcba3c4124ab371297d52260135924
: end :: Saved
ASA Version 8.4(4)1
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address dhcp setroute
interface GigabitEthernet0/1
nameif inside
security-level 99
ip address 192.168.1.254 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 99
ip address 192.168.100.1 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name dock.local
same-security-traffic permit inter-interface
object network inside-network-object
subnet 192.168.1.0 255.255.255.0
object network management-network-object
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.250.0_25
subnet 192.168.250.0 255.255.255.0
object-group network AllInside-networks
network-object object inside-network-object
network-object object management-network-object
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit icmp any any echo-reply
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
access-list split_tunnel standard permit 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool Anyconnect-pool 192.168.250.1-192.168.250.100 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic AllInside-networks interface
nat (inside,outside) source static inside-network-object inside-network-object destination static NETWORK_OBJ_192.168.250.0_25 NETWORK_OBJ_192.168.250.0_25
nat (inside,outside) source static management-network-object management-network-object destination static NETWORK_OBJ_192.168.250.0_25 NETWORK_OBJ_192.168.250.0_25
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.100.2 255.255.255.255 management
http 192.168.100.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 192.168.100.0 255.255.255.0 management
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_Anyconnect_VPN internal
group-policy GroupPolicy_Anyconnect_VPN attributes
wins-server none
dns-server value 8.8.8.8
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelall
split-tunnel-network-list value split_tunnel
default-domain value dock.local
username sander password f/J.5nLef/EqyPfy encrypted
username aveha password JA8X3IiqPvFFsZCT encrypted privilege 15
tunnel-group Anyconnect_VPN type remote-access
tunnel-group Anyconnect_VPN general-attributes
address-pool Anyconnect-pool
default-group-policy GroupPolicy_Anyconnect_VPN
tunnel-group Anyconnect_VPN webvpn-attributes
group-alias Anyconnect_VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http
https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email
[email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4636fa566ffc11b0f7858b760d974dee
: end: -
VPN Connects but unable to access internal devices
Thank you in advance for any assistance that can be provided.
I am using AnyConnect to create a VPN with an ASA 5505. Once connected, the client needs to access a device behind a 1941 router.
Internally, (not using VPN), all my routing is working correctly. My VPN client can connect and when I put a route on my 1941 router, I am able to ping that particular device. But my VPN client cannot appear to ping anything else, either the devices on the same internal range as the ASA 5505 or anything past the 1941.
VPN Client ASA 5505 Workstation 1941 Router Far Device
192.168.201.20 -----> Outside IP x.x.x.x // Internal 192.168.101.1 192.168.101.56 192.168.101.2 // 192.168.8.1 192.168.8.150
Client connects and get IP from ASA
Cannot ping this Cannot ping this
Can ping internal IP of 1941
*(after creating a static route)
I have been playing around with my configuration extensively to try and make this work. Split-tunneling is enabled and is required.
Here is my current config:
hostnameMYHOST
enable password mUUvr2NINofYuSh2 encrypted
passwd UNDrnIuGV0tAPtz2 encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.101.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.x 255.255.0.0
interface Vlan7
no forward interface Vlan1
nameif DMZ
security-level 20
ip address 137.57.183.1 255.255.255.0
ftp mode passive
clock timezone MST -7
dns domain-lookup outside
object-group network obj_any_dmz
access-list nonat extended permit ip 192.168.101.0 255.255.255.0 any
access-list nonat extended permit ip 192.168.201.0 255.255.255.0 any
access-list split-tunneling standard permit 192.168.101.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu DMZ 1500
ip local pool Internal_Range 192.168.101.125-192.168.101.130 mask 255.255.255.0
ip local pool vpn_pool 192.168.201.20-192.168.201.30 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 10 interface
nat (inside) 0 access-list nonat
nat (inside) 1 0.0.0.0 0.0.0.0
nat (DMZ) 10 137.57.183.0 255.255.255.0
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
route inside 192.168.8.0 255.255.255.0 192.168.101.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable 64000
http 0.0.0.0 0.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ca trustpoint ASDM_TrustPoint1
enrollment self
subject-name CN=MYHOST
keypair ClientX_cert
crl configure
crypto ca certificate chain ASDM_TrustPoint1
certificate 0f817951
308201e7 30820150 a0030201 0202040f 81795130 0d06092a 864886f7 0d010105
05003038 31173015 06035504 03130e41 494d452d 56504e2d 42415455 53311d30
1b06092a 864886f7 0d010902 160e4149 4d452d56 504e2d42 41545553 301e170d
31333036 32373137 32393335 5a170d32 33303632 35313732 3933355a 30383117
30150603 55040313 0e41494d 452d5650 4e2d4241 54555331 1d301b06 092a8648
86f70d01 0902160e 41494d45 2d56504e 2d424154 55533081 9f300d06 092a8648
86f70d01 01010500 03818d00 30818902 818100c9 ff840bf4 cfb8d394 2c940430
1887f25a 49038aa0 1299cf10 bda2a436 227dcdbf f1c5566b c35c2f19 8b3514d3
4e24f5b1 c8840e8c 60e2b39d bdc0082f 08cce525 97ffefba d42bb087 81b9adb9
db0a8b2f b643e651 d17cd6f8 f67297f2 d785ef46 c3acbb39 615e1ef1 23db072c
783fe112 acd6dc80 dc38e94b 6e56fe94 d59d5d02 03010001 300d0609 2a864886
f70d0101 05050003 8181007e 29e90ea0 e337976e 9006bc02 402fd58a a1d30fe8
b2c1ab49 a1828ee0 488d1d2f 1dc5d150 3ed85f09 54f099b2 064cd622 dc3d3821
fca46c69 62231fd2 6e396cd1 7ef586f9 f41205af c2199174 3c5ee887 42b684c9
7f4d2045 4742adb5 d70c3805 4ad13191 8d802bbc b2bcd8c7 8eec111b 761d89f3
63ebd49d 30dd06f4 e0fa25
quit
crypto isakmp enable outside
crypto isakmp policy 40
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 DMZ
ssh timeout 10
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-md5 rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
ssl trust-point ASDM_TrustPoint1 outside
webvpn
enable outside
svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1
svc enable
group-policy ClientX_access internal
group-policy ClientX_access attributes
dns-server value 4.2.2.2
vpn-tunnel-protocol svc
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split-tunneling
default-domain value access.local
address-pools value vpn_pool
ipv6-address-pools none
webvpn
svc mtu 1406
svc rekey time none
svc rekey method ssl
username ClientX password ykAxQ227nzontdIh encrypted privilege 15
username ClientX attributes
vpn-group-policy ClientX_access
service-type admin
tunnel-group ClientX type remote-access
tunnel-group ClientX general-attributes
address-pool Internal_Range
default-group-policy ClientX_access
tunnel-group SSLClientProfile type remote-access
tunnel-group SSLClientProfile general-attributes
default-group-policy ClientX_access
tunnel-group ClientX_access type remote-access
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:da38065247f7334a5408b7ada3af29ae
: endok, lets go on ... ;-)
Split-Tunneling: The ACL must include all networks you want to reach through the VPN:
access-list split-tunneling standard permit 192.168.101.0 255.255.255.0
access-list split-tunneling standard permit 192.168.8.0 255.255.255.0
NAT: Don't use "any" in the nat-exemption, but specify all traffic that should not be natted:
access-list nonat extended permit ip 192.168.101.0 255.255.255.0 192.168.201.0 255.255.255.0
access-list nonat extended permit ip 192.168.8.0 255.255.255.0 192.168.201.0 255.255.255.0
Routing: The 1941 needs a route for the vpn-pool pointing to the ASA (just in case there is no default route to the ASA)
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni -
Internet connected but unable to load web pages
Hi - My computer is an Imac, late 2006 model. For some reason I seem to be having problems connecting to the internet using the Airport connection. Using the Ethernet cable everything is fine no problems whatsoever, but wireless connection just doesn't happen. I have run through all the relevant diagnostics and checked the wireless router modem settings. My wife recently bought a MacBook - it connects wirelessly without a hitch. I even changed the iMac setting to exactly the same as the MacBook, but still nothing. I get the green lights in the Network Diagnostics screen, but when I try to load a page in Safari I just get an error message " Not connected to the Internet, or Server failed to respond".
My broadband ISP is Virgin Media (not a cable connection - it's ADSL) and the wireless router modem is a Netgear DG834GSP v3.
Any ideas anyone as am getting really frustrated at not being able to connect wirelessly.
Thanks in advance.Hi I have been having exactly the same problem for the last couple of weeks, and can't explain what is happening either. The Mac seems to be connected to the Internet with all of the status 'lights' in Network diagnostics green. I am picking up an IP address but can't load any Web pages. Very puzzling !
-
Wifi Connected but unable to access internet 9300
Hello
I recently changed my data plan on my device but after I did so I realized my wifi connection wouldn't work. My wifi connection is fully connected (and my data is turned off) but it won't work at all.
Please Help
Solved!
Go to Solution.AmandaTemple wrote:
Hello
My wifi connection is fully connected (and my data is turned off)
Hi AmandaTemple
Welcome to BlackBerry Support Forums
On Manage Connection you can turn off your Mobile Network , But have to TURN ON your Data Services .Can you try that and see if it allows .
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it. -
I. Am unable to update Apps from iTunes via the apps button messages says unable to connect but can access iTunes directly via iTunes button on iPad
Cheers -
Since my last update for Mac OS X Lion 10.7.5 I have been unable to print to either my HP or Lexmark printers! Everything is connected but I get an "idle" message in the queue. I have "Reset printer system" and re-added these printers. No luck. Help?
Hello,
It isn't the fw in Network you want o use or look at, that's for something completely different.
My first suspect is the Power Adapter on the LaCie has gone.
At the Apple Icon at top left>About this Mac, then click on More Info, then click on Hardware>Firewire, what is listed there?
Reset the Firewire bus
If your Firewire or USB isn't recognizing any device. A solution which has worked for some whose hard drive became invisible in 10.4 was simply to follow these four steps to reset the Firewire/USB bus:
1. Shut the machine down.
2. UNPLUG the power lead to the computer and any firewire/USB drive or devices.
3. leave it for 10 minutes.
4. Connect back up and reboot.
http://www.macmaps.com/firewirebug2.html -
My iPad is connected to wifi but unable to display contents from iPad to TV via ATV
A.MY iPad is connected to Wi.Fi but unable to display contents from my iPad to TV via my ATV
Look at the Apple TV manual
http://support.apple.com/manuals/#appletv
Cheers, Tom -
"Unable to connect to server" I have wifi connection but I'm getting this error when I try to purchase an app. Why? If anyone knows can you please help me thank you in advance. :-(
Can you load a webpage in Safari with that wifi connection? If so then it's a problem with the iTunes Store app connection. If not then your wifi isn't fully functional and you need to troubleshoot that first.
-
I have a valid internet connection but I'm unable to connect to the iTunes store.
I have a valid internet connection but I'm unable to connect to the iTunes store.
having the same problem. I tried every possible solution given to fix it.
Maybe you are looking for
-
[SOLVED] Pacman "config file could not be read" error during Arch ins
I've been attempting to get Arch setup for a while now, and after having some trouble with partitions, my wireless connecting, and setting up repos and mirrors, which the Wiki helped me solve, I've hit a bigger bump. While updating the system using
-
Suspect Bug in iPhoto 9.4 in OS X 10.8.2
The first time I used the iPhoto 9.4 red-eye reduction tool after updated to OS X 10.8.2 I noticed iPhoto was not saving the changes. I posted a Help request under the iPhoto topic Help saving red-eye edits https://discussions.apple.com/message/19718
-
Network printing with time capsule doesn't work with OS X Lion
I have a canon printer which will print when it is set up and connected to my imac. However when it is set up and connected to time capsule it will not print. It thinks it has completed the job but it hasn't. I think that this may have something to
-
how can i force eject a cd from mac pro no icon on desktop or in finder, how can i force eject a cd from mac pro no icon on desktop or in finder
-
Populate multi record display item
Hellou gurus! I have forms 10g and i need to populate display item in enter query mode. My problem is that I have table T1 with some static values. Table T2 is through ID connected (reference) to table T1 1:1 cardinality and T2 table also have refere