Oam/cfm on cisco 888E and tagged pkt

I'm configuring cisco 888E for oam functionality using tag.
I created controller shdsl without bounding, it is possible to associate vlan to Ethernet interface automatically configured when dsl-group is created?
For default all pkt received from FastEthernet 0 are forwarded on Ethernet 0?
from configuration file:
controller SHDSL 0
dsl-group pairs  0
  shdsl annex G
I receive tagged pkt from FastEthernet 0 (conncted to switch) but pkt aren't forwarded on Ethernet 0 interface (line side).
Oam/cfm is configured as following:
ethernet cfm ieee
ethernet cfm global
ethernet cfm domain md2 level 7
ethernet cfm domain md1 level 5
service ma1 vlan 213 direction down
  mep mpid 3
  continuity-check
  continuity-check static rmep
  sender-id chassis
  ais period 1
  ais level 7
  no ais suppress-alarms
  lck level 5
I tried to enable debug
Sep 30 12:49:32.819: EOAM PD(Et0): total_rx_frames=         290
rx_error_frames=           0
rx_error_symbols=           0
rx_crc_error_frames=           0
tx_crc_error_frames=           0
Sep 30 12:49:32.819: EOAM PD(Et0): pqii_pro_ucc_fe_get_oam_counters: Returned
Sep 30 12:49:32.819: EOAM LM(Et0): SYMPRD w=104857600 lt=1 ht=0 elapsed_time=7000(ms) rx_sym=39872000 err_sym=0 bw=5696
Sep 30 12:49:32.819: EOAM LM(Et0): FRM w=1 lt=1 ht=0 t_frm=0 err_frm=0
Sep 30 12:49:32.819: EOAM LM(Et0): FRMPRD w=10000000 lt=1 ht=0 t_frm=290 err_frm=0
Sep 30 12:49:32.819: EOAM LM(Et0): RXCRC w=1 lt=10 ht=0 err_frm=0
Sep 30 12:49:32.819: EOAM LM(Et0): TXCRC w=1 lt=10 ht=0 err_frm=0
Sep 30 12:49:33.815: EOAM TX PAK(Et0) size 20:
Sep 30 12:49:33.815: 03 00 08 00 01 10 01 00 01 00 0D 05 DC 00 00 0C
Sep 30 12:49:33.815: 00 00 00 02                                    
Sep 30 12:49:33.819: EOAM PD(Et0): pqii_pro_ucc_fe_get_oam_counters: Called
I enabled EOAM only on Ethernet 0.
I have problem on EOAM tagged pkt and also using tagged traffic.
Cisco#show vlan-switch
VLAN Name                             Status    Ports
1    default                          active    Fa1, Fa2, Fa3
213  shdsl                            active    Fa0
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup
Any suggestion on configuration?
Thanks

Wrong Section, You should be asking it in IOS-XR section.

Similar Messages

  • Communication problem between Cisco 3560 and Cisco SG300.

    Dear Support,
    I have a Cisco SG300 and Cisco 3560 switches.
    3560 is my Core Switch and SG300 is access switch.
    From 3560 VLAN information is not passed to SG300.
    3560 Configuration:
    interface GigabitEthernet0/23
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 1,2,10,11
    switchport mode trunk
    SG300 Configuration:
    interface gigabitethernet49
    spanning-tree link-type point-to-point
    switchport mode general
    switchport general allowed vlan add 2,10-11 tagged
    macro description switch
    Please suggest how this issue is resolve.
    Regards,
    JItesh Mahajan.

    Dear Aleksandra,
    Below Configuration is right or wrong for 3560 and SG300.
    3560 Configuration:
    interface GigabitEthernet0/23
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan remove VLAN 1
    switchport native vlan 1
    switchport trunk allowed vlan 1,2,10,11
    switchport mode trunk
    SG300 Configuration:
    interface gigabitethernet49
    spanning-tree link-type point-to-point
    switchport mode general
    switchport general allowed vlan add 2,10-11 tagged
    macro description switch
    Regards,
    JItesh Mahajan.

  • VLAN and STP compitability between Cisco 2950 and SRW2048

    How Cisco 2950 and Linksys SRW2048 switches can be combined to work fine with more than one VLAN's and STP?? I want both switches to support three VLAN's and STP for loop free network.Can some body help me out to combine linksys and cisco switches to interconnect to form my Network???  

    I believe that the SRW2048 is a 48 port managed switch. The easiest way to set the VLAN and STP configuration of is to access the web utility of this switch via 192.168.1.254. You have to go to VLAN Management and he needs to create the VLANs. The default VLAN of the switch is VLAN 1. You need to create 2 more VLANs by choosing the VLAN IDs and the name you want for these VLANs.
     After creating the VLANS, you need to determine the LAN of the switch you want to assign to each VLAN and the Trunk port or the port where you need to connect the SRW2048 to the Cisco 2950 switch. Go to the port setting and make this port as “truck”, and leave the other ports as “access”. Go to VLAN to ports and manually allocate the each LAN ports to the desired VLAN ID number. Take note that all ports that are members of VLAN1 should be “untagged” and the rest should be “tagged”. Save the settings you made.
     The STP configuration for the SRW2048 can be found also in the web utility. Just go to the Spanning Tree tab and setup your desired STP configuration.
     For the Cisco 2950, I am not quite sure on how to create these settings but I saw a useful link that might help you:
     http://www.petri.co.il/csc_setup_a_vlan_on_a_cisco_switch.htm

  • Cisco 2950 and Dell Powerconnect 5224

    I am trying to Cascade a cisco 2950 and dell powerconnect 5224. I am connecting port 32 on the 2950 and port 24 (gigport) on the dell. Any idea on how I can get the cascading to work? This is what I have on the Dell and the cisco.
    Dell Powerconnect 5224:
    interface ethernet 1/24
    switchport allowed vlan add 1 untagged
    switchport native vlan 1
    switchport mode trunk
    switchport allowed vlan add 1,10 tagged
    Cisco 2950:
    interface FastEthernet0/32
    switchport access vlan 10
    switchport mode trunk
    Dell documentationon casdcading between powerconnect and catalyst 4000 talks about setting up GVRP on both the dell and cisco switches. However, 2950 doesn't have GVRP.
    http://www.dell.com/downloads/global/products/pwcnt/en/app_note_4.pdf
    Any ideas, tips. Thanks.

    Try this instead:
    Dell:
    interface ethernet 1/24
    switchport allowed vlan add 1 untagged
    switchport native vlan 1
    switchport mode trunk
    switchport allowed vlan add 10 tagged
    Cisco 2950:
    interface FastEthernet0/32
    switchport mode trunk
    switchport trunk allow vlan 1,10
    switchport nonegotiate
    You don't need "switchport access vlan 10" on the Cisco because it's not in access mode, it's in trunk mode. And on the Dell you don't want vlan 1 to be tagged and untagged.
    Good luck.

  • OAM 11g Single Sign-On and OAM 11g Cookies

    Hi all,
    I need to know following,
    is it possible to get the username and password from the OAM 11g + IIS Webgate cookies and forward the same to the application for further authentication? is there any way to decrypt the cookie and use the information in the application?
    Regards.

    Yes , you can get the user password ,but for that you will have to write a custom plugin , else it is not possible.
    Refer step number 9 in the blog Single Sign on with Oracle Access Manager: Creating a Custom Authentication Plugin

  • Routing issue between Cisco Nexus and Cisco 4510 R+E Chassis

    We have configured Cisco Nexus 7K9 as core and Cisco 4510 R+E as access switches for Server connectivity.
    We are experiencing problem in terms of ARP learning and Ping issues between Cisco Nexus and end hosts.

    Hi,
    So you have N7k acting as L3 with servers connected to 4510?.
    Do you see the MAC associated with failing ARP in 4510?. Is it happening with all or few servers?. Just to verify if it is connectivity issue between N7k and 4510, you can configure an SVI on 4510 and assign address from same raneg (server/core range) and perform a ping.
    This will help narrow down if issue is between server to 4510 or 4510 to N7k.
    Thanks,
    Nagendra

  • How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

    how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

    Hi ,
     Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA  outside interface . 
    Accordingly you can configure NAT 
    HTH
    Sandy . 

  • How can we remove the Calender,Active tasks,Recent activity and tags sectio

    Hi
    I want my landing page of my workspace (Keppel_Energy_EAP) to have only the WIKI home screen and want to remove the other sections like calender, Activie Tasks, Recent Activity and tags section.
    Can you please let me know how i can remove these sections.
    Thanks
    Ashok

    Hi,
    The teamcollab client is not modifiable unfortunately - what you have on the page is always there.
    Phil

  • Cisco wireless and Apple Mac woes

    Hello all,
    I've been working with Cisco wireless and WLC's for a couple of years now but the recent onslaught of Apple Mac's is giving me heart burn.  I've seen this at numerous sites now and need to throw it to eht community for guidance.
    Basically we have had a number of instances where the Macs just fall off the wifi.  Sometimes it's when they wake from sleep and other times when roaming between AP's (1131s with same SSID's).  Our standard install is WPA2 and per ap local authentication.  PC's work fine and never an issue.
    We have completed a survey with a spectrum analyser and no RF interefence is present nor errors on the radio interface.
    Questions:
    - Is there a preferred Cisco config/setup for Mac's to work reliably?  I've heard loads of rumors but nothing concrete and nor can I find anything specific.
    - Should I be setting up WDS in case there is an authenticating issue.
    - For those who are Mac gurus and happen to be reading. What Mac options we should look at?
    This has all come to a head because the clients IT company who recommended the Macs (different from us doing the network infrastructure) are insisting that the problem is Cisco incompatibility and that we should rip out the Cisco kit and install airports (what tha!!!).
    Thanks in advance for any pointers.
    For those who like a config here it is .... Vanilla stuff really
    Building configuration...
    Current configuration : 2236 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname AP4
    no logging console
    enable secret xxxxxxxxxxxxxxxxx
    no aaa new-model
    dot11 syslog
    dot11 ssid Home
       vlan 1
       authentication open
       authentication key-management wpa
       guest-mode
       mbssid guest-mode
       wpa-psk ascii xxxxxxxxxxxx
    dot11 ssid avnet
       vlan 2
       authentication open
       authentication key-management wpa
       mbssid guest-mode
       wpa-psk ascii xxxxxxxxxxxxxxxx
    username abcd password 1234
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption vlan 1 mode ciphers tkip
    encryption vlan 2 mode ciphers tkip
    ssid Home
    mbssid
    speed  basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
    channel 2412
    station-role root
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio0.2
    encapsulation dot1Q 2
    no ip route-cache
    bridge-group 2
    bridge-group 2 subscriber-loop-control
    bridge-group 2 block-unknown-source
    no bridge-group 2 source-learning
    no bridge-group 2 unicast-flooding
    bridge-group 2 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    hold-queue 80 in
    interface FastEthernet0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface FastEthernet0.2
    encapsulation dot1Q 2
    no ip route-cache
    bridge-group 2
    no bridge-group 2 source-learning
    bridge-group 2 spanning-disabled
    interface BVI1
    ip address 192.168.10.54 255.255.255.0
    no ip route-cache
    ip default-gateway 192.168.10.1
    no ip http server
    no ip http secure-server
    bridge 1 route ip
    line con 0
    line vty 0 4
    login local
    end

    Yeah!! even i have come across multiple issue with MAC and Cisco.. these are the below settings which i normally do on the cisco gears and most of the times this solved the issue..
    on the IOS AP disable Aironet Extentions and set the poer local and ofdm to max
    no dot11 extension aironet
    power local cck max
    power local ofdm max
    end
    On the WLC, disable Aironet IE..
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

  • Are captions and tags in backup when reloading after a computer crash?

    I have Adobe photoshop 11. I have backed up my photos in an external hard drive and also on carbonite. If my computer crashes and I need to reload my photos back onto my computer will the captions and tags still be there? I was wondering because when I just look at my photos on the hard drive it does not look the captions are there. Is there a special way to save them so they are there?

    If you use the backup command in the organizer file menu, all your media files will be saved, as well as the catalog which contains all the information about your media files : their location (path), exif camera data, your tags, captions etc. The restore command in the organizer will let you recover everything where you want to (same computer or not).
    If you are using any other external backup solution, only your media files will be saved, not the catalog and its data, unless you also backup the catalog; it's a folder containing the database and associated files. You find its location in the Help, System Info menu.
    You could also use the file menu of the organizer to 'save metadata to files', which would write the tags and captions in the header of the files themselves. If you reimport those files in the organizer, tags and captions will be recovered.

  • I want to move the move my photoshop elements photo database from an old pc to a new pc without losing the modified dates and tags created, what is the best way to transfer the database with all the information about the photos

    an old pc to a new one. How to I transfer the database file to save dates that have been modified and tags that have been created

    See:
    Use Backup, Restore to move catalog | Organizer | Elements 6 or later

  • Save Catalog and Tags etc,as I want to uninstall PSE6, then re-install

    I have just used the "Backup and Restore" in Pse 6 and backedup to an external F drive.But I didn;t put it into a special folder. Will I have trouble Restoring it, when I re-install pse6 back on the computer. Will it restore the catalog etc as it was before, tagged and catagorized? I have about 10.000 photos in the catalog..    Or do you suggest I use the "Backup and Restore" function again, only this time creating a folder for it..before sending it to the external F drive.   I have plenty of room on the external drive.   I look forward to a response
                                                                                      Thanks Pattie.
    If the 2nd option is the way to go, I will then have to delete the first backup from Ex F drive, how will I know what to delete. How will I recognize it, as the EX F drive is structured to backup  other files outside of PSE6.

    Thanks di,
              but do you mean I can uninstall pse than reinstall pse, and all my catagorized and tagged photos will remain the same.
    Also the reason I want to uninstall both pse and premier elements, and a few other things is, as recently I tried to delete a few files I thought were not needed, I think I deleted something important, because I could not get just the organizer to open.  I have since been able to open it by renaming it from thumb.5.cache to old.5.cache.  But since then a few more problems have arisen. Like when using Premier el 4 to make a movie, it's very slow. and not recognizing myDVD burner .  It has more in it's name now. Like HL-DT-ST  DVDRAM  GH20NS10  ATA Device.  I'm sure it didn't have the DVDRAM written there before.  When I go to Burn to Disk it won't recognize either the DVD drive or the Inserted DVD.    Everything has changed so I though I would remove both programs completly from computer then re-install them to see if that may help

  • I set up iPhoto v9.6 to copy items to library. Now I would like to change it to not copy. Do I have to start completely over? I have 106GB of photos and tags in my library. Will I lose all that work?

    I set up iPhoto v9.6 to copy items to library. Now I would like to change it to not copy. Do I have to start completely over? I have 106GB of photos and tags in my library. Will I lose all that work? Originally I thought by copying items to library I would be making an exact copy of my originals and that would serve as a duplicate or backup copy. My originals are on my EHD#1 and my iPhoto library is on my EHD#2. But now I realize that I can not view my iPhoto library unless my EHD#2 is connected to my computer (duh!!) So now I would like to NOT copy times to library and I want to have the library in the Pictures folder on my laptop HD. So I guess my question is do I have to start completely over? Is there some way to salvage all the work I've done so far?

    Yes you would have to start over from scratch.
    But you should really think this through very carefully. Experienced users do not recommend iPhoto used in this mode, and with very good reasons. Among them
    1. It's more work for exactly no gain
    2. It's unreliable - especially - when the library is on one volume and the photos are on another. One change to the path between the files and the library and you'll be reconnecting every photo in the Library back to the database, one by one.
    For more on iPhoto and file management see this User Tip:
    https://discussions.apple.com/docs/DOC-6361

  • The difference of the IEEE802.1x Auth between Cisco Routers and Catalyst switches

    Hello
    I am investigating the difference of the IEEE802.1x Auth between Routers and Switches.
    Basically dot1x auth is availlable on Catalyst Switches. however if I want to check to
    PortBased Multi-Auth , MAC address Auth and any certification Auth with this feature,
    Is it possible to integrate into Cisco Router such as Cisco 891F ?
    In my opinion Cisco891F is also available to use basic IEEE802.1x but if it compares with Catalyst switches such as Cat3560X
    I think there might be any unsupported feature on Cisco 891F.
    I appreciate any information. thank you very much in advance.
    Best Regards,
    Masanobu Hiyoshi

    Many time in interviews asked comaprison between cisco  routers and switches that i was answerless bcoz i dont have much knowledge about that.Can anyone provide me the compariosin sheet of the same.how are the cisco devices differ with each other how much Bandwidth each routres support and Etc...
    Ummmm ... The most common question I get is "what is the difference between a router and a switch".
    However, if you get a question like this, then my impression to this line of questioning are:
    1.  The candidate they are looking for has in-depth knowledge of routers and switches.  And I mean IN-DEPTH!;
    2.  They are not looking for a candidate.  They just want to stroke their ego.  There is not alot of people who can give you the "names and numbers" of routers and switches at a snap of a finger.  And if you do happen to know the answer, then and there, then expect a tougher follow-up question. 

  • Where can I get an Html error report of all the syntax and tag problems?

    Where can I get an Html error report of all the syntax and tag problems?

    Thank you for your answer.
    Where is the DW validation for me?
    My files are in my computer so I don’t have an external URL.
    File > validation > as xml = closes DW... Maybe because it is not a correct command for HTML,
    And
    Window > results > validation = gives a partial mistakes (e.g. shows an open tag without closing tag, but doesn’t show a closing tag without an open tag).
    Thank you.

Maybe you are looking for