Offset compensation on multiple modules with different input limits

I want to acquire different value voltage signals from SCXI 1122 modules. I can this signals group in two ranges, and connect them to different modules, but I can have signals differing 1:100 on a single module as well. How can I do the offset compensation for each channel and each module?

Hi James,
May be this is not the optimal choice the HW but an existing one. I shall coock with existing species. The Labview manual states, that in such cases the LV chooses the highes possible gain in the SCXI module, and then applies different gains to different channels on the DAQ board. But I suppose, the offset of the full signal path depends not only on the gain of the SCXI module, so it means, for all gains I would need separate offset value. Principally I can supply an array of offset values to the Scaling constant tuner VI, but these constants is determined on a channel named ....calgnd. In this case the Acquire and average VI accepts only the first member of the input limits array, and I get only one offset for this limits. Is it enough for all
different gains of the DAQ?

Similar Messages

Multiple AI channel reads with differant input limits

I want to aquire two high frequency AI channel signals from my SCB-68 at the same time. The signal is coming from two seperate pressure transducers. One needs to be sampled at 2000Hz with a voltage range of -10V to 10V and the other sampled at 200000Hz with a voltage range of 0V to .12V. I have been using the AI Waveform Scan.vi to aquire the two channels. But that requires two seperate case structues and activating them in sequence.

SCB-68 is just a connector block so it has nothing to do with your acquisition challenge. Some DAQ devices can be set up for different gains per channel, but others cannot. If your device cannot have different gains per channel, then you either need to do all the acquisition at +/-10 V and give up resolution on the other channel or use an external amplifier on the low voltage channel.
Similarly, most DAQ devices cannot sample two channels at different rates. Acquire both channels at 200 kHz and use decimation or other processing to reduce the data to the equivalent of 2 kHz for the slow channel.
Another option would be to use two DAQ boards and set the gains and sampling rates differently on each. The acquisitions could use a common trigger and with a sepa
rate frequency divider could have synchroized clocks if that is important.
Lynn

BO xi 3.1 u2013 schedule a template for multiple reports with different column

Hi,
I need to migrate the existing reports from SQL Server Reporting Services to BO, and the column order in the report is very important to the clients since clients have existing code to ingest these reports into their database. Now I want to schedule a single template with different parameters for all reports in BO, or create a single template with lot of parameters for all reports. My question is how I might use one template to create multiple reports with different column orders in the reports?
For example, client A has the following column order in their report: firstName, LastName, DateBirth, SSN. Client B has the following column order in their report: SSN, DateBirth, LastName, FirstName. Can I use one template to create these multiple reports?
Thanks!

Hi,
The only approach I can think of is to create a template report which uses variables
For each column you would need to variable
v_columnAName and v_columnAValue
v_columnAName would have a if statement in it
=if([client]="clientA" or [client]="clientC";NameOf([firstName]);if([client]="clientB";NameOf([SSN]);NameOf([lastName]));
v_columnA would have a if statement in it
=if([client]="clientA" or [client]="clientC";[firstName];if([client]="clientB";[SSN],[lastName]));
This would only work when you had a small set of clients.
This might be more managable if it was done in the universe
Regards
Alan

Single invoice for multiple orders with different divisions

Dear All,
while I am trying to do single invoice for muliple orders with different divisons invoice is gettting splitted..In copy control vbrk routine I tried with 003 and 007 etc..but result is same..what configuration need to be done for getting the single invoice
Thanks In advance
Regards
CNRNAIR

Hello
single invoice for multiple orders with "different divisions" invoice is getting split
FYI - Different Division means different Sales Area.
So, sales doc (whether sales order, Delivery & Billing) is applicable to EXACTLY one sales area.
Thus, combining docs with different sales area is practically impossible.
Provided, you are using common division.
Hope this assist you,
Thanks & REgards
JP

How can I edit multiple clips with different frame rates on the same timeline

how can I edit multiple clips with different frame rates on the same timeline

You do not want to edit material from different frame rates on one timeline. You CAN do this, but it is a very bad idea - and this is why.
Once you establish the sequence frame rate - lets say it is PAL material at 25fps, any material that you drop into the sequence other than 25 fps will have to be changed to play at 25 fps. If the material you add is NTSC (29.97), FCP will DROP 5 frames per sec to bring the frame rate down to 25 fps. Which 5 get thrown away? Every 6th one. This yields a funky cadence that becomes even more complex as as there are also interlaced fields (DV/NTSC is an interlaced format). Oh, and by the way, the image sizes are different as well. DV/PAL has 576 lines of resolution and DV/NTSC has 480. FCP has to scale up the NTSC to fit the PAL frame.
You do not want FCP adjusting these things on the fly. You want to do a thoughtful (and time consuming) conversion so that you end up with all your material in one format with the best possible image from the conversion process. Compressor can do an adequate job with Frame Controls turned on. The Natress Standards Conversion FCP plugin is another way to go. A third option is to find a post house that can do the conversion for you using a hardware based process.
The good news is, once everything is in the same format, editing it will be painless and the output process very quick.
Whatever frame rate/ image size you select, I'd suggest using ProRes for the codec. It is 4:2:2 color and will withstand color correction and composting with much more grace than any variant of DV based codecs.
Have fun.
x

Can I Turn off iMessage in a group text with multiple people with different devices? There's 1 person in the group text that doesn't use iPhone anymore and they can't see any messages that are sent unless we send as regular text individually.

Is there a way to turn off iMessage for a group text that includes multiple people with different non-apple devices? When a message is sent, only the iPhone users can see the iMessage. Those without them cannot see the texts unless we send individual Text Messages or turn off iMessage completely.

now I have this and it still doesn't work.
Section "ServerLayout"
Identifier "Simple Layout"
Screen "Screen 1" 0 0
InputDevice "Mouse1" "CorePointer"
InputDevice "Touchpad" "SendCoreEvents"
InputDevice "Keyboard1" "CoreKeyboard"
Option "OffTime" "1"
EndSection
Section "ServerFlags"
Option "AutoAddDevices" "False"
Option "DontZap" "false"
EndSection

Multiple Orders with Different reasons on a Single day

Hi,
I am recently learning Device Management of IS-U Electricity. Now I have a problem with meter reading orders generated at the time of periodic meter reading with reason 01 and different system generated orders with reasons like 22, 21 , 16 and 11 which are the orders get created internally based on device replacement and modification.
If the scheduled meter reading date lies on the day or the day before of device replacement or modification, the meter reading for the periodic order is getting prorated based on the meter reading entered at the time of replacement or modification. This is what I dont want.
Is it possible to have multiple orders with different reasons on the same date? Any configuration changes are welcome.
- Arghya

Hi,
You can acheive this using following config changes.
SAP Utilities --> Device Managment -->Meter Reading --> Meter Reading Order -->Order Creation --> Define Automatic Interpolation for Meter Reading Reason.
Uncheck the 'Auto Interpolation' flag for Meter Reading reason 01.
This will not use the Replacement or Modifiaction read.
Let me know if anything more is reuiqred.
Thanks and Regards,
Ranjit Thakur.

Define Multiple Taxes with different Accounts

Dear Members
I have defined tax in Oracle R12 . and defined multiple rates. these all tax deducted in a single Tax account. but my requirement is, there should be multiple taxes with different acccounts. when I define multiple taxes the system gives error unable to Calculate the tax. when I only enable one tax it works.
Current sanario tax rates
2% Account # 666461
3% Account # 666461
3.5% Account # 666461
Required Sanario
2% Account # 666461
3% Account # 666462
3.5% Account # 666463
Should be different
Do you have any Idea How I configure it.

Hmmm, thought I did that but ran into issues...Will give it a harder look.
Thank you for your reply, tt2...BTW, I've been reading these forums for awhile now and your replies in other posts have helped me so thanks for all of them, too...

Printing multiple PR with different line items in smartform

Hello all,
I have an requirement to print multiple PR with different line items on different pages.
So,suppose two PR are there,PR1 and PR2 with n no of line items,then i should get each PR on different page with its line items.
Note: One loop processing is already there on line items.
Best Regards,
Anurodh

Hi,
Fetch all the PRs and its corresponding items into 2 different table. Then Loop at the internal whihc contains the PRs and call the 2nd internal table for its items and call the FM for smartforms and pass them.
LOOP AT it_PR.
fetch all the items into it_PR_item
Call Function Fnam
Passign the it_PR_item
ENDLOOP.
Regards,
Aditya

How to go about multiple inclination with different data selection in Delta

We have to copy large amount of data ( more than 42lak of recodes) selectivly from on ODS to other ODS. in delata load ( BW 3.5 enverioment)
I thought of loading data in slices through delta loading with selection condition.
step 1> Do The initialization with selection condition as for calyear =2001 ( Init without data transfer )
step 2> Take the delta load .. it will take all delta record with same selection
step 3> Now I want to do Initialization with selection condition as for calyear =2002
step 4> take the delta now it will take delta for year 2001 and 2002 both Right ?
Here what problem I am facing.. while doing 2nd time initialization it prompt me to delete the last initialization request form scheduler menu.
if i delete the last request .. will it take the delta for previous initialization selection and new initialization selection. ?
Please advice how to go about multiple inclination with different data selection in delta loading.
Looking forward your reply.

Hi,
step 1> Do The initialization with selection condition as for calyear =2001 ( Init without data transfer )
step 2> Take the delta load .. it will take all delta record with same selection
step 3> Now I want to do Initialization with selection condition as for calyear =2002
step 4> take the delta now it will take delta for year 2001 and 2002 both Right ?
You are correct with this scenario normally. The message you mentioned normally comes up when you open a infopackage and don't change the selection first or in case you have overlapping selections with an already done init.
regards
Siggi

Running the same code multiple times with different paramters automatically

Hi guys,
I want to run the same code multiple times with different paramters automatically. Actually, I am doing some sample scans which takes around 2 hours n then I have to be there to change the paramters and run it again. Mostly I do use folowing paramters only
X_Intial, X_Final, X-StepSize
Y_Intial, Y_Final, Y-StepSize
Thanks,
Dushyant

All you have to di is put all of the parameters for each run into a cluster array. Surround your main program with a for loop and wire the cluster array through the for loop. A for loop will autoindex an input array so inside the for loop you just have to unbundle the cluster to get the parameters for each run.
Message Edited by Dennis Knutson on 07-13-2006 07:50 AM
Attachments:
Cluster Array.JPG ‏9 KB

Design a single template for multiple reports with different column order

Hi,
I need to migrate the existing reports from SQL Server Reporting Services to Crystal Report 2008, and the column order in the report is very important to the clients since clients have existing code to ingest these reports into their database. Now I want to create a single template with lot of parameters for all reports. My question is how I might use one template to create multiple reports with different column orders in the reports?
For example, client A has the following column order in their report: firstName, LastName, DateBirth, SSN. Client B has the following column order in their report: SSN, DateBirth, LastName, FirstName. Can I use one template to create these multiple reports?
Thanks in advance.

-As I mentioned you can find Template Field object in Insert menu of crystal report Designer 2008.
As soon as you select Template Field object you will be able to see a box beside ur mouse cursor. Drag and drop this box at required place. Now when you place this object in report you will get some thing like this "<TemplateField1>" listed under Formula Fields tree. Double click "<TemplateField1>" formula to add your conditions.
-I have not tested it for large amount of Customers. However as the number of customer increases the number of conditions will get increased.
For the customer that want the same ordering of columns you can put those customers under one condition.
    for Example...
          if(?Client in ['clientA','clientA']) then
                    <TableName>.<Field>......
-What do you mean be 40 columns? Do you mean 40 fields or you want to show 40 columns in report? Please elaborate.
Regards,
Amrita
Edited by: Amrita Singh on May 21, 2009 7:54 AM

Multiple profiles with different cache settings

I want to have multiple profiles with different settings for the cache. I'll call them ProfileOne and ProfileTwo for simplicity's sake. ProfileOne I want to clear its cache on exiting Firefox and on ProfileTwo have it retain its own cache. I have already setup both profiles and configured them accordingly with ProfileOne's privacy settings for Clear History > Cache checked so it clears on exit and ProfileTwo is not set to clear anything on exiting.
The main issue is that after doing something with ProfileTwo then switching to ProfileOne, upon exiting ProfileOne it also deletes ProfileTwo's cache. I have tried using the profile manager to create the profile in a different location than default to no avail. Is there any way to set it so ProfileOne's cache can still be cleared on exit without affecting ProfileTwo's cache?

After checking a few different options, it looks like the add-on Better Privacy provides the options I need for LSO management and does separate HTML cookies from Flash cookies nicely and lets me save specific site's LSOs. Thanks for the assistance!

Radar chart with multiple KPIs with different scales in dashboard4.0

Hi Experts,
How to create a radar chart which is having multiple KPIs with different scales. ?
Thanks in Advance
Saidulu

Hi Sai,
Customizing the chart is not possible, example the data in you criteria is like the below.
Take four row based chart to display the row based values, if the columns are having different values. Take column based chart if the difference in row based, hope you got it.
Use the label in combo box and use the dynamic visiblity to call the chart from the back.
Hope you got the idea.
--SumanT

How do I send docs to multiple signators with different email addresses on Echo sign ?

How do I send docs to multiple signators with different email addresses on Echo sign ?

Thanks man...the problem could be on the signators side.
Rick Schell...Realtor, ABR
www.rick-the-realtor.com
Cell 615-804-3085
Crye-Leike Realtors
Office 615-373-3513
Fax 615-373-5228
Quoting Echosign-Rob <[email protected]>:
Echosign-Rob created
the discussion
"How do I send docs to multiple signators with different email
addresses on Echo sign ?"
To view the discussion, visit:
https://forums.adobe.com/message/6395941#6395941
>

Offset compensati​on on multiple modules with different input limits

Similar Messages

Maybe you are looking for

Offset compensation on multiple modules with different input limits