OS Lion and Samsung ML-1660 printer problem

Since downloading OS Lion my ML-1660 laser printer won't print unless I switch it off then switch it back on. It then prints OK. If I want to print another document I have to sw. off and on again. This problem doesn't happen on my Epson RX520 3 in 1 printer.
I've downloaded the latest Samsung driver software but this makes no difference. Can anyone advise how I can rectify this, please?

Hi, I have the same problem with Maverick, with mountain lion worked perfect. in the get this error: The function `CGContextErase 'is obsolete and will be removed in an upcoming update. Unfortunately, This application, or a library it uses, is using this obsolete function, and is thereby Contributing to an overall degradation of system performance.

Similar Messages

Lightroom, OS Mountain Lion and Epson 7880 large print problems

I have used Lightroom to beautifully print many 20x16, 24x20 and 24x36 prints on my Epson 7880.
I have been trying unsucessfully to print a 24x74 panoramic print.
What happens is I geet a 24 x 20 inch blank piece of paper come out of the printer, a huge waste of expensive paper!!
I have set yp a custom paper size and the image looks like it fits the dimensions perfectly from the LR print module. All looks perfect.
I am using OS Mountain Lion and LR4. Any suggestions would be greatly appreciated.

http://support.apple.com/kb/DL1398

Hi! I just bought Lion and I am having a problem with the installation. It keeps telling me that the computer's hard drive has a S.M.A.R.T. problem. How can I solve it?problem.

Hi! I just bought Lion and I am having a problem with the installation. It keeps telling me that the computer's hard drive has a S.M.A.R.T. problem. How can I solve it?
Thanks!
Angela

You may have a hard drive problem. When I installed Lion, the installer told me that it couldn't complete because the hard drive was failing (or broken, the exact words escape me). Since the HD had been functioning just fine, I took it to the Genius Bar, and found out that yes, the hard drive was slowly dying (bad sectors). I couldn't reboot into Snow Leopard, the installer wouldn't let me and then the drive just wouldn't work at all.
I had to replace my drive and restore from Time Machine. Thankfully, I had Time Machine, and had just done a backup 5 minutes before the crash.
Best of luck.

I upgraded to Lion and now can't print PDF files and Acrobat reader doesn't work anymore. What can I do to get it working?

I upgraded to Lion and now can't print PDF files and Acrobat reader doesn't work anymore. What can I do to get it working?

If you upgraded and were using a version of Acrobat Reader that was legacy, that is PPC compatible, then you will have to upgrade to a version compatible with Lion as Lion no longer has Rosetta to interface with the legacy software.
I know that Acrobat, full version, 10 works with Lion...use it myself.

I installed Lion and now seem to have problems with Microsoft Silverlight and other plug ins and applications. I haven't ever used time machine to back up (my bad I know). Is there a way to go back to snow leopard with messing up all my files and my set

I installed Lion and now seem to have problems with Microsoft Silverlight and other plug ins and applications. I haven't ever used time machine to back up (my bad I know). Is there a way to go back to snow leopard with messing up all my files and my set?

Are you using the latest version of Silverkeeper? - v.2.0.2 is stated to be compatible with Snow Leopard.
http://www.lacie.com/silverkeeper/
If it's messing things up you could try asking LaCie Support for assistance.

I installed mountain lion and now my kodak printer is not working. Any sugestion please

i installed mountain lion and now my kodak printer is not working. Any ideas? please help

What errors do you see? The /var/log/cups/error_log file might have some more information.

I recently upgraded to Lion, and immediately started having consistent problems with Open Office 12 (would hang, and need a Force quit to recover). Has anybody else seen these problems? Any solutions other than going back to Snow Leopard? (I did).

I recently upgraded to Lion, and immediately started having consistent problems with Open Office 12 (would hang, and need a Force quit to recover). Has anybody else seen these problems? Any solutions other than going back to Snow Leopard? (I did). But I'd like to use iCloud with iPad.

Hi Pete. The repair of disk permissions can help resolve any application crashing or misbehaving.
As for Lion and the two camps, I think that is a reasonable observation. In my office we have about a dozen Mac's and about one third of those Mac's had problems after updating from 10.6 to 10.7. The main problem for these Mac's was a loss of wifi stability. But for the other two-thirds, Lion was a smooth transition.
Personally, my Lion experience was fine. But I did get a new i7 MacBook Pro with Lion already installed and only had to migrate my user data from a 10.6.8 TM backup.
So I think that is a key for Lion's operational success. A clean install of Lion on a new Mac would not cause too many operational issues. But an installation, or more correctly, an update to Lion from SL increased the chances of failure for some users - especially when old software & plugins resided on the Mac. And I would say that they were the people that you saw at the Apple store.
As for the "latest release of Lion fixed my problems" statement, my experience with these and other forums is that people mostly only go there to complain about the problems they are having. If they are having no problems then they either keep it to themselves or they try to help the users who are experiencing trouble...

G3 Pismo Powerbook and HP Deskjet 3325 Printing Problems

The problem is that the Deskjet fails altogether to print sometimes. The error message tells me to allocate more memory to the printer. I do so but this does not help at all. I have 128Mb virtual memory turned on in addition to the built-in RAM of 128Mb.
Might the problem simply be lack of RAM? There does seem to be plenty of memory available if I look at ‘About this Computer’
In order to try and solve this problem, I have updated
OS 9.1 to 9.2.1 to 9.2.2 successfully
downloaded and installed the latest printer driver v.6.4 from the HP download site
I now have two options, among others, in the left-hand window of the Chooser:
The old printer driver called something like Deskjet 5.3 and the new printer driver called Inkjet 6.4
If I select the former, which is what I always did in the past, the Deskjet 3325 printer appears in the right-hand window of Chooser, I select it (with AppleTalk inactive) and then the document sometimes, but sometimes not, prints OK.
If on the other hand, I select the Inkjet 6.4 driver in the left-hand window, no printer at all appears in the right-hand window. If I just continue from here and give the print command inside, for example a Word document, the print dialogue appears, I click on print, but am then told that I have selected a model called HP 6670, which is the wrong model of printer, and must therefore select the right model. The Inkjet Printer Utility does not offer me the option of selecting the right model viz the 3325, or indeed any model.
It may or may not be relevant, but I have Word 5.1 and Word 98 on the G3. Printing problems seem to occur far more with Word 98 than Word 5.1.
I would be most grateful for any help. Thanks.
Nick
G5 iMac Mac OS X (10.4.6)

Well. I'll answer my own question in case anyone is interested.
Uninstall the HP printer drivers.
To do this, delete all references to HP in the Extensions, Disabled Extensions, Preferences and Startup folders, all of them in the System folder, by selecting them, dragging them to the Trash and emptying the Trash.
Then do the same with all references to HP items in the Applications folder.
Download and reinstall the most-up-to-date printer driver avaialble for your printer from the HP website.

Illustrator cs4 and Epson Stylus R2880 printing problems

I am having printing problems. I am trying to print from my cs4 to my epson stylus photo printer r2880 and am having problem with my picture getting cut off on the left side when I print. The print screen looks perfect but when I go to print, it always cuts off the left edge and the bottom. I tried playing with the x and y's but have no idea what I am doing. Does anyone have this combination of cs4 with the R2880 printer and can help me solve my problem?

Hi Wade,
I have tried playing around with that but I am not sure what I am doing. Here's what it is set at.
On my drop down print screen, i have the size set as US Letter (Sheet Feeder Borderless (retain size).
When I check the 'fit to page' button it actually puts a bigger white boarder around it. The fit to page number says (96.4706%). Shouldn't it say 100%? If I leave it as do not scale I still have a small border around it.
I am not sure about the xy settings. When I have it to 'fit to page' it is:
Top left corner (0,0) Top right corner (0,0)
Bottom left corner (0, .1632) Bottom right corner (0, .1632)
If I have do not scale button clicked:
Top left corner (0,0) Top right corner (0,0)
Bottom left corner (0, -.225) Bottom right corner is (-.3, -.225)
Do these settings look correct? If not, what should my setting say and how can I set it without the setting changing back everytime I open this window.
Thanks for responding,
Celeste

[Solved] Samsung SCX-4300 Printer Problem

Hi everyone. I installed Arch Linux today. Everything is fine except printer. I am using Samsung SCX-4300 printer and scanner. Scanner works fine but CUPS doesn't see the printer. I can't see anything on CUPS web interface's Local Printers area. Here is a screenshot.
I can see my printer in lsusb command:
Bus 002 Device 004: ID 062a:0201 Creative Labs Defender Office Keyboard (K7310) S Zodiak KM-9010
Bus 002 Device 003: ID 04e8:342e Samsung Electronics Co., Ltd
Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 001 Device 003: ID 046d:08d7 Logitech, Inc. QuickCam Communicate STX
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
So why I can not see my printer and how can I fix that?
Last edited by DoGuKaN (2013-07-30 20:13:21)

I have a very similar printer (SCX-4500W) and found that I was able to get it working as a printer but that I could not get both print and scan functions to work at the same time.
In order to get the printer going I had to add a file to /etc/udev/rules.d/71-scx4500w.rules with the content as a single line:
ATTR{idVendor}=="04e8", ATTR{idProduct}=="342b", MODE:="0664", GROUP:="lp", ENV{libsane_matched}:="yes"
You will need to change the idVendor and idProduct in the line above to match that for your own printer from the lsusb command instead of those above for the SCX-4500W.
I would also suggest that you use the splix drivers package - i.e. make sure that the splix package is installed with:
# pacman -S splix
Then when you add the printer select the splix drivers which will work with that printer (you should check the splix support page to check your printer is supported but I am pretty sure it is)
Once that is done then you need to start the cups.socket daemon with the following command as root (exclude the # which is the prompt)
# systemctl start cups.socket
and if it then works, and allows you to add the printer, then you also need to "enable" the same daemon so that it starts after the next boot as well:
# systemctl enable cups.socket
One other thing is that if you want your printer to be discoverable as a cups remote printer on your local network you will need avahi-daemon running on the server to which the printer is attached, as well as on any machine which needs to see it - check the arch wiki on how to set that up if you need it.
I hope this helps.

MSI G31M3 and Samsung SyncMaster 943NWX resolution problem

hi.today i bought a new computer.i.e assembled.i have a MSI G31M3 motherborad and Samsung SyncMaster 943NWX 19" inch monitor.The box in Samsung SyncMaster 943NWX 19" inch monitor says that it has 1440*900 high resolution.I also know that it must have that much max resolution,thats why i bought this monitor.But the problem is that in desktop->setting.There is not any 1440*900 resolution to select.
First there was resolutions from 800*600 to 2080*XXXi forgot.But there wasn't any 1440*900 resolution to select.Not even in the range of 1440.There was only one 1400 range.Then i installed the driver came with the monitor and now the settings shows only resolution upto 1280*768.
So can anyone tell me whats going on?I search the net for this problem but has no luck.one guy was says to use Powerstrip tool but i have no luck.Though the powerstrip tools shows that my monitor has 1440*900 max resolution in its info section but the resolution doesn't show up in resoultion select range.So i guess my monitor is correct.
My question is that is it due to internal graphics that does support this resolution or something else.Please help me to solve this issue.

thankx a lot "NovJoe".I installed the intel.inf driver provided in the motherboard.I also installed the graphics accelerator/driver came in the CD and also driver downloaded from the intel site.Both look same driver.But no luck.And what do u mean by "intel 945G onboard graphics driver"?I guess i have intel g31/33 graphic accelerator.do i need to install intel 945G onboard graphics driver as well? I have searched the net but can't find anyone with exact problem.There was one guy with similar problem but there is no solution.
Do you think this is a driver a problem?May be following link will help u to get some idea
http://article.gmane.org/gmane.comp.freedesktop.xorg/28102
http://www.avsforum.com/avs-vb/showthread.php?t=961716

Will Archive and Install fix my Print Problems?

Was running 10.39, all was fine.
Repaired Permissions, used Tiger Update DVD
to update from my 10.39 to Tiger 10.4.
Rebooted, repaired permissions from Tiger Disc.
Rebooted, installed OSX 10.4.4 Combo update to
get up to latest Tiger.
Ran all patches I need from Software update,
rebooted to Tiger Update DVD,
repaired all permissions.
Rebooted back, now I cannot print to my Canon i560 USB printer.
I get the dreaded "services-" error.
I re-downloaded the driver from Canon's Website
(disc is misplaced right now). Tried to load it, got to
a part in the installer, and hung. After half and hour,
force quit it, rebooted, tried the "Printer Repair Permissions" fix, Printer Utility now shows the Canon Printer as a USB printer, but the driver selection gives
me a lot of "BJ-Gimp" printer selections, but no "i560".
Now the kicker: I took the printer and disconnected it
from the Mac, and connected it to my wife's iBook,
which runs 10.4.3, and it found and connected flawlessly,
and I could get a PDF printed.
My other issues on this mac is that Compressor has stopped
working, but I have got it to the point of where it
at least run somewhat using a Terminal fix I found
on the forums. But I'm strongly thinking that to get this
baby into shape and running smoothly like the iBook
does, I should do an Archive and Install of OSX 10.4,
then patch up to 10.4.3, then possibly 10.4.4.
Any thoughts before I make the attempt?

Thanks, after a looooong night of re-installing
back from DVD to 10.4, then up to 10.4.3,
(why press my luck?)
then re-installing FCP 4 and DVDSP 3, and doing all patches, both my Compressor 1.21 works great as before, and I got my printer settings back. I did have a bit of a bout with the
"blue screen of death" but all is great now!

Trouble printing with Leopard and Samsung USB laser printer

I just purchased a Samsung SCX-4200 laser printer/scanner/copier. After installing 10.5-compatible drivers from the Samsung website, I'm unable to get the printer to work. Print+Fax recognizes the printer fine and the proper driver appears in the pulldown menu so all seems good there. But every time I go to print a document (I've tried numerous apps), the job begins spooling to about 6%-8% (depending on document tried) and then I get a message in the queue window that says 'Waiting for USB printer to respond.' and the job just hangs there. The job list shows the document as printing and the Print+Fax window shows the printer as in use, but no matter what I try, this thing just won't print. I've tried restarting the computer, rebooting the printer, an older version of the drivers that came with the printer (says OS 10.3-10.4 only) and myriad other tricks, but no dice.
Anyone have any advice? Thanks!

Well to follow up I finally heard back from Epson support...this was the response (note that it says nothing that I did not tell them already).
Thank you for taking the time to contact Epson. It is my pleasure to
respond to your inquiry. Color management is an art, make sure that only
the application or the driver is handling the management. Turn off the
management in the driver if you are allowing Photoshop or other software to
handle the color management. Also make sure when you are allowing
Photoshop to handle the color that you select the proper printer profile.
It's very hard to help with color management via email, you may want to
check some of the on-line color management websites on google.
David P
EPSON Professional Graphics Support Team
Totally useless as I explained in detail that I had already done all of this and was very familiar with color management and the process of using it. And that it was not until the latest OS-X and Epson's driver that the problems started.

Samsung CLX-3185W printer problem

Not been on here for a while, Eric has had no problems, sends his love to Ronda !
Anyway as a treat I got him the above colour laser printer, but here is the problem I installed the software as per the instructions and restated now I can scan/fax over the wireless network great but I can not print ! as soon as I press print a window pops up saying printer off line. If I connect the USB cable no problems at all............but I want WiFi.
thing I have done so far.
Re installed all the software - restart
Downloaded the latest drivers from Samsung and installed them, same thing !
Turned off Eric at the end of the install, turned off the printer too still nothing.
WiFi network is working correctly ie can see other computers and internet....................Help
Custom mini.

Ronda Wilson wrote:
Thanks, but how does one go about finding the IP address of the printer?
Just an FYI Ronda, this (from the Samsung Website:
Note the omission of any variant of OSX after Leopard
Let me find a manual and I'll tell you how to find the IP address
FYI, Samsung manuals download at a rate best described as, Glacial!
Printing a network configuration report
You can print Network Configuration Report from the machine’s control panel that will show the current machine’s network settings. This will help you to set up a network and troubleshoot problems.
Press Menu on the control panel.
Press the left/right arrow until Network appears and press OK.
Press the left/right arrow until Network Info. appears and press OK.
Press the left/right arrow until Yes appears and press OK.
Using this Network Configuration Report, you can find your machine MAC address and IP address.
For example:
MAC Address:00:15:99:41:A2:78
IP Address:192.0.0.192
I am not responsible for numbering

TS3276 I recently installed LION and have been having email problems, sending and receiving since. My server (Cable-fiber optics) tell me they see nothing wrong, that it is a program issue. I get messages about not recognizing the certificate.

If I click the go-ahead button, I am warned about not be assured of security danger. This keep happening over and over. It is a pain using email since LION. I went into Keychain Access and tried choosing an Apple certificate, but that is never permanent. Should I just ignore the warning? Will this kind of problem disappear with Mountain Lion? Is there a solution?

What email program are you using?

OS Lion and Samsung ML-1660 printer problem

Similar Messages

Maybe you are looking for