P35 Platinum R-G-R-R (Persistent)

First - the Moan guide stats:
CPU brand, model and speed (eg AMD Athlon64 3000+ 'Venice' core): Intel Core 2 Quad 6600 Kentsfield 2.4 GHz
# Motherboard model (eg K7N2 Delta2 Platinum, NOT just MS-6570!!): MSI P35 Platinum
# Memory brand, type/speed, size, number of sticks (eg 2x Crucial 512mb DDR400): 2 Sticks Crucial 2GB DDR2, 5-3-3, CL4 (also tested using 4 sticks Samsung 512MB 4-4-4 in varous combinations)
# Video card brand, chipset type, memory size (eg Gainward Geforce 6800GS 512mb AGP): BFG nVidia 8800GTX 768MB
# Hard drive(s) brand, size, type, speed (eg 2x Seagate 200gb SATA150) : 1x Seagate 250gb SATA2 7200rpm
# Operating system and version (eg Microsoft Windows XP Home Edition SP2): Windows Vista Ultimate
# Power Supply Unit brand and output in watts and DC output (amps): BFG 650w Split Rail (20A per rail)
New install, I have not tweaked any settings. Basically, when I power on the system, I get the D-LED R'G'R'R - which the manuka says it is stuck on memory. I have tried many different combinations with no luck. I also get no video output. Looking for any advice or help.
Also of note, LED3 is lit red- pressing the BIOS reset button does not clear it. The manual says that this means the system is in a standby state - but not how it got there or how to recover it.
Thanks in advance

That is not necessarely the only correct answer. Your CPU operates at 266 MHz FSB-frequency. That means at least in theory 533 MHz modules should work if the BIOS is able to detect them and if it sets FSB/DRAM ratio to 1:1.
However, try officially supported modules first. If you have a spare 667 MHz standard RAM module or if you can borrow one, use those for testing.
In a worst case scenario, your board came with BIOS v1.3, which seems to have major compatibility issues. With generic 667 Mhz RAM, it is in most cases possible to work around these problems. This may not be the case, I am just providing an alternative explanation to your problem. Try with different RAM first.
Also, the board has two jumpers that allow you to pre-set certain default FSB-clock speeds (200, 266 and 333 MHz). Have a look at your mainboard manual to compare jumper settings.

Similar Messages

P35 Platinum ... Initializing Floppy Drive Controller ?? (Wont Boot)

Hi all
I have built a new comp for someone who wants reliability so i choose to go Platinum, but ... i cant make it boot.
It wont even show ANYTHING on the screen (tried the vga in both Pci-e 16x just in case i was dumb enough lol) the boot "procces" stops with the Status leds showing:
4) Green
3) Green
2) RED
1) Green
According to the user guide it says:
Initializing Floppy Drive Controller.
This will initialize floppy drive and controller.
And i dont even have a floppy
Well as the problem persisted i removed EVERYTHING from the motherboard
now i left:
-Mother
-Processor
-Memory
-VGA
-PSU
And thats it. Let me tell you all the things i tried:
-Bios reset (with the little red button)
-Plug only necesary things
-Taking off the battery and replacing it (and went back to the "original")
-Tried different connectors just in case it was the PSU (i really dont think so)
-Tried different memory stick/s.
And well, thats all i think, half of this i did it with the mother in the case, and re-did all the list with the moter OUTSIDE the case. Can anybody help me ??
I guess is a BIOS problem, as i readed in another post (yeah used search first xD) but the only guy who could solve the problem was flashing the bios, but i cant even see a word on the screen, is it possible to flash the bios in my condition ??
The specs now:
Intel C2D E4500
MSI P35 PLATINUM
2x1Gb (or 1x1gb, tried single sticks as well) OCZ DDR2 667mhz (and tried also with generic "titan" memory at 800mhz, does not change anything)
Gigabyte 8400GS
POWERCOOLER PS-500 SS PSU
AFAIK i have more than enough to make this boot, but well ... you know
Thanks in advance, i tried to give all details possible, in 2 days ill go to RMA if i cant make it work, but i would like give it a try, who knows
EDIT: my english sucks really bad, forgive me !!
EDIT2: Forgot to add !! when i remove the VGA the motherboard DOES the "VGA ERROR BEEP" and the leds are in the correct combination for VGA ERROR ... so i guess processor works and ram too (both OCZ and generic), if one of these fails then it wont make any sound, m i wrong ??

ITS ALIVE !!!!!!!!!!!!!
Well, to be honest, i dont know what it really was but tried 2 things:
First i followed step by step and word by word the "clearing CMOS" guide (this mobo has a button and not a juper, so i pressed the button like 2 minutes to be REALLY sure xD), then i realized that it was not doing the "beeps" anymore, but the screen was black like before.
SOOOOOOOOOOOO THEEEEEEEEN ... (shoot me in the head for this) i unplugged the video and keyboard from the KVM switch (could THIS be the problem ?? i used it wit hundreds of computers and never gave me prblems before ??? ??? ???) and plugged the cables directly and now its alive !!!
THANKS !! :D :D :D :D :D
One last thing !!
Do you recommend me to upgrade the BIOS ?? the board always did a "false boot" then starts normally, i readed it was some "hardware checking" feature, its that true or its totally useless ??
THANKKKKKKKKKKKKKKSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS SSSSSSSSSS =) (im so damn happy now LOL)

P35 Platinum & P35 Neo2 Series

beta BIOS for P35 Platinum & P35 Neo2 Series(MS-7345, PCB 1.1) ver V1.4B3:
BIOS Sign-on message: A7345IMS V1.4B3 083107 (Date: 08/31/2007)
Attachment name: P35 Platinum and P35 Neo2 Series 1.4B3.zip
Make and ensure PC is stable before proceed. flash BIOS from USB key, by using our Tool(easy & safe way to flash):
MSI Forum HQ USB Flashing Tool
Use Beta or Modded BIOSes at own risk!
Feeback are Welcome!!! Thanks!!

Quote from: Jack the Newbie on 25-September-07, 04:00:50
A new BETA has just surfaced in the German MSI Forum: A7235IMS.151 (09/21/07).
For anyone interested, here is a Link to the BIOS (use at your own risk!):
http://msi-forum.de/thread.php?threadid=31968&threadview=1&hilight=&hilightuser=0&page=3#post281405
Changelog will follow shortly. The admin did not find the time yet.
The changelog did not follow that shortly after all, but it goes like this:
Quote
Fix some DDR can not boot issue
There seems to be a new beta (1.5b2) around. Unfortunately I don't have a link to it, but here is the changelog:
Quote
Fix Smart FAN Fail from S3 wake up issue
Here it the Link to BIOS 1.52 BETA. The BIOS was just uploaded. Use it at your own risk!!
http://www.msi-forum.de/thread.php?threadid=31968&threadview=1&hilight=&hilightuser=0&page=4#post283564

Problem installing MSI P35 Platinum & MSI NX8600GT & windows XP

Hi all,
I just bought my MSI P35 platinum mobo and MSI NX8600GT graphics card.
Was trying to install XP on it. During installation, got the following error message :
A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you've seen this Stop error screen, restart your computer. If this appears again, follow these steps:
Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.
Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical Information:
*** Stop : 0X0000007E (0XC0000005, 0XF748E0BF, 0XF78DA208, 0XF78D9F08)
*** pci.sys - Address F748E0BF base at F7487000, DateStamp 3b7d855c
Then it just freezes there. Any ideas how I can resolve this ? Please help
Thanks ...

Quote from: NovJoe on 07-February-08, 00:17:44
Please post your full system specs and PSU specs amps.
Moan Guide
my system specs
Intel Pentium 4 - Intel E8200, LGA775 2.66GHz, 6MB L2 cache, 1333 Mhz FSB, 45nm
MSI P35 Platinum
3 x 1GB DDR2 Kingston 6400 CL5 800MHz
320GB Seagate SATA HDD
MSI NX8600GT 256MB
Windows XP Pro
PSU : I-CUTE ATX-450W/P4
The HDD was detected correctly in BIOS, memory also detected, Graphics card seems ok (how I can tell ?)
rgds

P35 Platinum: I have to press the power button multiple times to start

Hello fellow MSI customers,
as written in the subject, I have a problem with starting my PC. When I press the power button, the computer powers on, but there is no output to the screen. In fact, my LCD stays in standby mode. I can hear the fans running, so something is going on. According to the LEDs on the mainboard, it is a memory problem.
Now I turn the computer off, using the power button (have to hold it for a few seconds). When off, I start again and everything runs as it should.
After starting, I ran memtest86 multiple times without any errors. I ran a few games, compiled some programs, installed Vista 64bit, Linux, all without any crashes or hangups. It is just the starting that makes problems. After booting it is very stable.
Seeing that it could be a memory problem, I brought another pair of memory, just to be sure. I couldn't reproduce the problem on that day! Any type of memory I put in (the one before, or the newly brought home) the computer always started on the press of the button. So I thought, OK, maybe they were not seated correctly. But, alas, two days later it is again only starting by pressing the power button three times.
What I tried:
1. Boot using only 1 piece of memory stick
2. Boot using only 1 piece of memory, but different one
3. Use another pair of memory <- worked, but on that day it also worked using my original memory
4. Disconnected everything except graphics card, to make sure it is not a power supply issue (minimized power usage)
5. Tried all of the above with a different processor
6. Used another power supply
Any other ideas?
Here are my specs:
MSI P35 platinum
Core2 Q6600
Nvidia 7900GT
4GB V-Data DDR2 800MHz <--- I think this is the problem, any experiences?
Enermax Liberty 400W
a few other things (HDDs, XFi, DVD-RW)
By the way, how can I boot from an external DVD-RW? It doesn't show in the menu when I press F11 (boot menu).
Thank you for any help, muro
And just to let a bit of steam off:
1. I had major problems with the RAID controller (not MSI fault, rather intel) - I put two disks into a RAID 0, then RAID 1 and they always failed after a few boots - member missing on both disks. I was getting angry, so I put them as normal (non RAID) disks and everything is fine since, although no RAID.
2. Installing anything except windows with an IDE DVD-RW is very hard. It took me ages until I got Ubuntu booting (there are guides on the net, google is your friend), and much longer to get grub (boot loader) working. Long story short - if you have multiple disks, use the Linux disk as the bootable, do NOT put grub on the disk where Vista is installed.
3. I have no idea, how to update the BIOS, if I had to. I'm using 1.1 that came on the board. I use 64bit Vista and Linux, none of which is supported to upgrade the BIOS. Any hints how to do it (if I needed to)?

Hello,
now today is the day I've finally received my replacement board. The good news first - it DOES work! Yepeeee!
Now some more information:
The jmicron controller seems to be missing - a screen with something about "Marvel" is shown before the intel raid screen. However, it is only visible for a fraction of second, so I cannot read it. I think it detects my IDE DVD-RW so I'm quite certain it's the replacement for jmicron. I won't miss it - it took me ages to install Linux with the jmicron controller.
The problem where I had to restart the computer sometimes because it didn't even post (RAM error) is gone. It boots just fine now.
I had an extremely long first post - about a minute, but after that it boots very fast now.
anyway, regarding some questions around here - the manual states MSI recommends using an 350W power supply. My 400W is more than enough. Please note - it is an Enermax, not one bundled with a cheap case. My cheap RAM sticks also work very well now. I did try them on different boards before, so now I know I just had a faulty board.
In the end, I can only say this: This is my 3rd board already and it's the first one that works well. As the hardware changed, I presume there were major issues with this board that lead them to make a new revision. What is strange, though, is that the revision is still 1.1, as were my previous two. I pity everybody who had the same problems as I did, but I can now say that I'm very happy about the board now.
Cheers, muro

P35 platinum ms7345, system won't load OS, stops at msi splash screen

motherboard in question is a p35 platinum ms7345
system won't load the OS, stops at msi splash screen, can't get into bios.
LED code stops at G-R-G-R "Testing Base and Extended Memory"
this is a system that I built over 8 months ago. the only thing I
did was upgrade the cpu to a E8400( from a e6750). I had no previous
problems. but after the upgrade. I first received an error
= attempt to overclock failed = ( cant quote but as I remembered it)
press any button to reset bios.( I have received this message before with the old cpu but with a restart the system went on as normal). After the system restart, it just sits on the splash screen. I never attempted
to overclock the memory. the jb1 & jb2 jumpers are on 1 & 2 pins(same way it
came from newegg). I tried to use different memory( in all of the slots) same outcome.
I unplugged
all other hardware except vid card> same outcome. I even used a different
vid card> same outcome.
system specs
core 2 e8400
msi p35 platnum
2gb(2x1gb) adata ddr2 800
any suggestions? I appreciate any help. I hope the board isn't finished
thanks in advance
NFIXIT

There are three possible solutions to solve the situation:
1) Install a processor supported by the current BIOS Version to be able to properly turn on your system and then update the BIOS to the latest Version to be able to use your E8400/E0 (update should be done from DOS only).
2) Ask in a local computer shop or contact your reseller to do the same thing for you.
3) Connect an internal floppy drive and a PS/2 Keyboard and then try to force the system into AMI BIOS Recovery Mode. Instructions:
Quote
Rename the desired AMI BIOS file to AMIBOOT.ROM and save it on a floppy disk. e.g. Rename A7345IMS.1xx to AMIBOOT.ROM
Insert this floppy disk in the floppy drive. Turn On the system and press and hold Ctrl-Home to force update. It will read the AMIBOOT.ROM file and recover the BIOS from the A drive.
When 4 beeps are heard you may remove the floppy disk and restart the computer.
Even though the AMI BIOS Recovery Procedure is the only chance you have to solve the situation without installing a different processor, it does not work in all cases. However, as it is an easy procedure, it is at least worth a try.

Need Help with Memory OC to 1066 on P35 Platinum Combo

Hi,
I've been trying to get my Corsair Dominator memory to 1066, but everytime I change settings, the system will not post. So far I've:
- Disabled EIST & DOT
- Disabled 'Configure DRAM Timing by SPD' and set values to 5-5-5-15 (left all others as is)
- Processor reports 333x9
- Set ratio to 1:1.6.7 bringing adjusted timings to 1109. I also have 1:1.2 for 1332 & 1:1.50 for 999
- Memory voltage set to 2.1
Not sure where to go from here as other MS reported here seem to have different settings than the P35 Platinum Combo.
Specs are:
- Intel E8400 3.0GHz Dual Core (45nm)
- MSI P35 Platinum Combo
- Sapphire Radeon HD 3870 512MB GDDR4
- Xigmatek NRP-MC651 650W Modular PSU
- Corsair Dominator 4GB 1066 DDR2 RAM (PC2 8500)
- Samsung 22X DVD Burner
- Lexa Blackline Case
Any advice welcome -- I'm at a loss.

Hi,
You would probably better off, posting in the Overclocking section than here.
https://forum-en.msi.com/index.php?board=27.0

P35 platinum combo will not boot windows after bios update via Live Update

Hi,
I had everything running on windows 7 fine until 2 days ago. I installed Live Update from MSI website. I was about to install driver updates for my motherboard, but the bios update went instead. my pc tried to restart after the bios update installed, but it failed. would not post and would only see black screen.
then i removed one of my memory sticks. it would post, but then windows would not start up. it would get stuck at windows loading screen. i tried to reformat with my windows cd. but during install it would blue screen of death me. i tried multiple times and it would always blue screen of death with different errors. the last one i remember was a message saying i should off turn shadowing and caching.
this all started happening after i attempted bios update via Live Update.
Any help is greatly appreciated.
I have a core2quad 9450
this motherboard
MSI P35 Platinum Combo LGA 775 Intel P35 ATX Intel Motherboard
http://www.newegg.com/Product/Product.aspx?Item=N82E16813130141
this ram
G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1000 (PC2 8000) Dual Channel Kit Desktop Memory Model F2-8000CL5D-4GBPQ
http://www.newegg.com/Product/Product.aspx?Item=N82E16820231145
this harddrive
Mushkin Enhanced Chronos MKNSSDCR120GB 2.5" 120GB SATA III MLC Internal Solid State Drive (SSD)
http://www.newegg.com/Product/Product.aspx?Item=N82E16820226236
this video card
XFX PVT88PYSF4 GeForce 8800 GT 512MB
http://www.newegg.com/Product/Product.aspx?Item=N82E16814150280
Thanks!!!

at a guess you need to reset bios to ahci
a bios flash defaults to ide mode

Can't install Vista Ult x64 or XP Pro on new MSI P35 Platinum setup

I am unsuccessful when trying to install. XP or Vista on those system. I boot with the CD/DVD they both go through the loading files screens, but once it completes it freezes completely and just idles.
And the LED3 lightis always RED.
I am unsure what to do at this point. Any help would be greatly appreciated. Thanks.
Intel E6850 3.0 gHz
MSI P35 Platinum
MSI 8800GTX
2 GB OZC
Seagate 7000.9 160 GB
Corsair HX620W
According to the MB the
CPU Temp is 96 - 110 C
System is 36 C

Ok....It appears that my cpu heatsink was not bolted down correctly. After fixing that the temp idels around 45 in BIOS... *sigh*

Oc on p35 platinum. is this just about the way to do this?

Crucial DDR2 PC6400 2GB CL6 x 3
Corsair HX 850W PSU
radeon hd 6870 xfx black edition
p35 platinum. ms7345
intel e 8500
Cooler Master Hyper 212 Evo CPU
hello
i have some questions about overclocking. i have the e8500 pcu.i am verry happy with that one..
i was you here that recomended it for me,so thanks for that.
but now i would like to get a bit mroe out of it...
i have newer done this kind of job before so bear with mee..
i have read a lot on the internet and have looked in the manual for the motherboard.
but i realy dont understand eny of it.. all the numbers and different things to change in bios.
so my reading up on it realy dindt work..
so i ask you,how to go forward...
thanks all good people. for eny replies.

have now tryed it.
here is my data
adjusted cpu fsb frequency 432
adjustet cpu frequency 4018
fsb/memory ratio auto
adjusted memory frequency 846
cpu v. 1,2750
memory v. 1,90
douse this seems okey?
seems like it works good this far
one thing more!
the cpu voltage that is in the pix is not right as it seems.
as soon as i started turning the fsb frequency , the voltage vent back to defalt.. and i didnt do it..just did it it self.
and the defalt vpu voltage was 1,0000.
so i tryed that voltage before i did eny oc. and the computer locked good. would also say the heat of the cpu that way dropped some..
could meybe the man who had it befor me mess the voltage ?
but now as i sead it looks good so far. with the oc data above.
so what is next to realy get the compoter checked out?
thanks

P35 Platinum stuck with 008D error in boot with newly added OCZ Fatal1ty rams

Hi,
I was using 2x1 GB 800 MHZ OCZ vista performance rams without any problem. I just bought 2x1 OCZ Fatal1ty 1066 MHZ rams. In the specification of my P35 Platinum mainboard it tells that it supports 1066 (OC).
I don't want of course to run all my rams at 1066 MHZ. I just want to run all of them at 800 MHZ.
However, when I placed all 4 rams in every combinotion on the slots, computer boots but it stuck after the boot screen and there is "008D" in the rightdown corner.
Interestingly when I just put Fatality rams (2GB) computer doesn't boot! Only 1xvista perf. Mhz 1xFatal1ty or 1xvista perf. Mhz 1xFatal1ty works but stuck at after the boot screen.
I tried to enter 5-5-5-15 values and tried to adjust memory voltage to 2.1 V as told in the new ram's specification but doesn't affect. What is your solution? Since new rams do not work among themselves, are they broken or my board doesn't support them?

If I'm not wrong, your post sounds to me that you are trying to mix the OCZ Vista and OCZ Fatal1ty RAMs on the same board.
This is highly not recommended as both RAMs are very different in most aspects (Speed, latencies, voltage and made).
I would suggest that you clear CMOS and choose which set you'll want to boot the system with and settle with that.

Is P35 Platinum Combo compatible with Windos 8?

I never imagined when I bought Windows 8 that my pc might be too old but looking at the driver supprot page for my P35 Platinum Combo makes me think now that I should not be using Windows 8. My pc has been having problems every since I installed Windows 8 on a new drive. For a while it would often crash/auto restart. Then things were ok for a while. Now, in the past week, my pc is really slow. Simple things like opening file explorer take a very long time. Surprisingly, in safe mode my pc runs faster.
Video Driver is up to date and has been since I installed Win 8 (radeon 13.1)
board drivers up to date
malware/adware/virus scanned
running with only an ssd drive. 80gb free space on a 160gb drive
followed ssd drive tweaks such as indexing off, prefetching off, maintenance off, RAC off, etc...
minimized virtual memory to better use my 8gb ram
Just wondering what others think about running Windows 8 on this motherboard of mine. My specs are:
P35 Platinum Combo (msi.com/product/mb/P35-Platinum-Combo.html)
Intel E8400 (ark.intel.com/products/33910/Intel-Core2-Duo-Processor-E8400-6M-Cache-3_00-GHz-1333-MHz-FSB)
Intel X25-M SATA Solid State Drive - 160 GB, 2.5 inches (ark.intel.com/products/56603/Intel-SSD-X25-M-Series-160GB-2_5in-SATA-3Gbs-50nm-MLC)
Kingston 8gb DDR 2 800
Saphire HD 7850
P.s.
Can't post complete links since this is my first post.

USER-HOSTILE! Hahaha! Hilarious vid I can sympathize with the author. I'm a fairly seasoned user and while I did manage to figure out all the controls, after much googling, I still had to deal with all the crashing and slow downs.
Well I decided not to waste any more time and reverted back to windows 7. All is perfectly functional now and at a nice healthy speed. I think my hardware was just too old for Windows 8 since my friends pc is running fine in Windows 8. Granted... He hates the interface and is now jealouse that I'm back to Windows 7, haha.
Now to create my next catastrophe! Updating my bios. lol. I noticed that the most recent version will provide support for L2 cache which would be nice since it seems my proccessor has that ability.
Thanx so much for your response Bernhard.

Help P35 platinum problems

Hi, I'm new in the forum.
I have bought a p35 platinum about three weeks ago, it is fantastic and I like it very much, but I have some problems with it.
If I list them, could you help me??
My complete configuration is:
mb: msi p35 platinum;
processor: Q6600 (without O.C.);
ram 4x1gb team elite ram 800mhz;
video: ati 2600xt 512mb gddr3;
. At first, the motherload's bios colour was black, but suddenly it became classic blue. Now it's blue yet. Is it normal?
. When I turn on the Pc it a emits "beep"(that should be a sign of bad operation of the AMI bios).
. The bios read 3.25gb of ram, but I've installed 4gb.
. dual core center inform me that the CPU fan is 0, while, it goes on spinning. (it happens often)
. A lot of programs, like Sandra or Everest 2007, read the chipset ICH9 instead of ICH9R.
. Live Update crash when it looks for bios versions.
. After installing the bios 1.3 the start is more slowly, besides there is a screened where I can read the marvel component. unfortunately I can read just this, then I will try to do a screen.
PS:
Despite of I had this problems, I go on loving my magic motherload. I hope you will help me, because I don't know what to do.
My O.s. is Windows vista Ultimate.

Quote
3. My O.S. is 32 bit vista ultimate and my O.S. too read 3,2gb of ram but, also when the O.S wasn't istalled on my PC, my platinum p35 read anyway 3,5gb that could be utilized and 4gb installed.
Read here:
https://forum-en.msi.com/index.php?topic=111120.0
You need a 64bit operating system to make use of all 4gb of ram.
Quote
it became classic blue. Now it's blue yet. Is it normal?
It is supposed to be blue.
Quote
2. The "beep" that my motherboard (that is new, nobody used it) emit is just one and short, one second after the apparition of MSI logo.
It means everything is OK.

Changing from the 975X PowerUp to the P35 Platinum?

Hi,
would it be a good move to change from the 975X to the P35 Platinum with the components you see below?
I'm mostly interest in a better performance and a motherboard that's ready for the future.

I would consider one of the upcoming X38 boards if I was you. Wait until these boards are on the market and watch user reviews and problem reports. The prices should have dropped a little in 2008.
You live in Germany, if I remember correctly, right? Did you have a chance to notice the X38 Hydrogen-Watercooling board yet? It will be a limited edition in cooperation with watercool.de:
- http://msi-forum.de/thread.php?threadid=33552&threadview=1&hilight=&hilightuser=0&page=2#post284169
- http://msi-forum.de/thread.php?threadid=33552&threadview=1&hilight=&hilightuser=0&page=2#post284175
As far as I know, there will also be a Combo-Version of the Hydrogen-Board.

Right Memory of a P35 Platinum

Ok just bought a P35 Platinum board, to replace my old board that I was having problems with. My processor is a Intel C2D E6400 2.13 Ghz L2 2MB. I have just bought OCZ 2GB (2x1GB) DDR2 1066MHz/PC2-8500 Dual Channel memory. Is this ok? Or have i Messed up? Also what tweaks will I have to make to get this mem working to its full potential??
Thanks
B

This is what I have:
$155 - http://www.newegg.com/app/ViewProductDesc.asp?description=20-220-037&depa=0
But this one has a bit better timings.
$185 - http://www.newegg.com/app/ViewProductDesc.asp?description=20-220-006&depa=0

P35 Platinum R-G-R-R (Persistent)

Similar Messages

Maybe you are looking for