Pdf printing failure

I have both a Canon i865 & a Canon iP4300. Suddenly the latter won't print pdfs (yesterday a very faint impression, today completely blank sheets. Test print OK and prints other documents. i865 will still print pdfs. I really need to use the iP4300, the i865 is getting temperamental.
Anybody met something like this? Any ideas?

Bernard Stay wrote:
Looking at the nozzle area under the cartridge - here there is a clean shiny gold foil. All the other cartridges show traces of ink.
If you are talking about the input section of the printhead where you see the fine gauze that attempts to restrict the flow of foreign matter into the head, then I have never seen an instance where after use the gauze is clean of ink. Have seen this with a new printer and printhead but never with a used one...
I'm talking to Canon about this but haven't got anywhere yet. I don't know whether it's possible to flush the nozzles or whatever. Wish me luck!
You may have to replace the printhead if the deep clean hasn't worked. When the ink cartridge makes contact with the printhead intake, the action of the ink being heated in the head causes the ejection of the ink bubble and also ***** more ink into the chamber. If this section of the head is not heating then no amount of flushing will help. If however the head is simply blocked then repeated deep cleans can get it working again. I've also read where people have taken the head out and used isopropyl alcohol to clean the nozzles.
Anyway good luck with getting it resolved.

Similar Messages

  • V10.1.5 upgrade - Adobe PDF printer issues - font embedding

    Hi,
    Accepted the 10.1.5 (Acrobat Standard) upgrade.  Have started having "Adobe PDF" printer failures with MS Outlook 2010: Font embedding issues.
    Is there a setting somewhere I need to tweak to tell it to substitute with another font when it runs into licensing issues?
    I've re-installed CutePDF as a workaround, but would prefer to use the Adobe printer.
    save-as-filename.log:
    "%%[ ProductName: Distiller ]%%
    %%[ Error: LucidaSans cannot be embedded because of licensing restrictions. ]%%
    %%[ Font vendor (B&H) does not permit this font to be embedded in PDF. ]%%
    %%[ Error: invalidfont; OffendingCommand: xshow ]%%
    Stack:
    500
    /l
    %%[ Flushing: rest of job (to end-of-file) will be ignored ]%%
    %%[ Warning: PostScript error. No PDF file produced. ] %%"
    Regards,
    JD

    In the settings file you should be able to set to continue even if the embed fails. In that case, I think you will simply have the PDF without the one font being embedded. You can also set to never embed it in the settings file (if you can find it on your system).

  • Another problem with PDF printing

    Hi all.
    I try new pdf printing in Apex 3.0 with printing engine Apache FOP and BI Publisher. Both engines seems work well. I configured Apex engine to use Standard Support for pdf.
    Next I imported example application http://www.oracle.com/technology/products/database/application_express/packaged_apps/pdf_demo.zip and run it. But when I press "print" link, instead pdf output I receive error page "404 Not Found The requested URL /pls/apex/f was not found on this server."
    Apex 3.0 reside on Oracle 9.0.2 database server and use it http server with modplsql. Both Apache FOP and BI Publisher works on standalone OC4J container.
    In Apex's http-server error log I noticed next error messages:
    [Fri Apr 13 16:07:11 2007] [warn] mod_plsql: Stale Connection due to Oracle error 22293
    [Fri Apr 13 16:07:11 2007] [error] mod_plsql: /pls/apex/f ORA-22293
    ORA-22293: LOB already opened in the same transaction
    Is anybody know what to do in this situation?

    Marc, thank you for your reply.
    application.log contains next messages:
    07/04/16 17:12:13.100 10.1.3.1.0 Started
    07/04/16 17:12:15.881 xmlpserver: QuartzInitializer: Quartz Initializer Servlet loaded, initializing Scheduler...
    07/04/16 17:12:16.975 xmlpserver: QuartzInitializer: Quartz Scheduler failed to initialize: org.quartz.SchedulerConfigException: Failure occurred during job recovery. [See nested exception: org.quartz.JobPersistenceException: Couldn't clean volatile data: ORA-00942: таблица или представление пользователя не существует
    [See nested exception: java.sql.SQLException: ORA-00942: таблица или представление пользователя не существует
    07/04/16 17:12:16.975 xmlpserver: Error preloading servlet
    javax.servlet.ServletException: Failure occured during job recovery.
         at org.quartz.ee.servlet.QuartzInitializerServlet.init(QuartzInitializerServlet.java:170)
         at oracle.apps.xdo.servlet.scheduler.quartz.ExtendedQuartzInitializerServlet.init(ExtendedQuartzInitializerServlet.java:115)
         at com.evermind.server.http.HttpApplication.loadServlet(HttpApplication.java:2361)
         at com.evermind.server.http.HttpApplication.findServlet(HttpApplication.java:4810)
         at com.evermind.server.http.HttpApplication.findServlet(HttpApplication.java:4734)
         at com.evermind.server.http.HttpApplication.initPreloadServlets(HttpApplication.java:4922)
         at com.evermind.server.http.HttpApplication.initDynamic(HttpApplication.java:1134)
         at com.evermind.server.http.HttpApplication.<init>(HttpApplication.java:738)
         at com.evermind.server.ApplicationStateRunning.getHttpApplication(ApplicationStateRunning.java:414)
         at com.evermind.server.Application.getHttpApplication(Application.java:545)
         at com.evermind.server.http.HttpSite$HttpApplicationRunTimeReference.createHttpApplicationFromReference(HttpSite.java:1990)
         at com.evermind.server.http.HttpSite$HttpApplicationRunTimeReference.<init>(HttpSite.java:1909)
         at com.evermind.server.http.HttpSite.initApplications(HttpSite.java:645)
         at com.evermind.server.http.HttpSite.setConfig(HttpSite.java:290)
         at com.evermind.server.http.HttpServer.setSites(HttpServer.java:270)
         at com.evermind.server.http.HttpServer.setConfig(HttpServer.java:177)
         at com.evermind.server.ApplicationServer.initializeHttp(ApplicationServer.java:2456)
         at com.evermind.server.ApplicationServer.setConfig(ApplicationServer.java:1004)
         at com.evermind.server.ApplicationServerLauncher.run(ApplicationServerLauncher.java:131)
         at java.lang.Thread.run(Thread.java:595)
    07/04/16 17:12:17.37 xmlpserver: 10.1.3.1.0 Started
    07/04/16 17:12:56.145 xmlpserver: QuartzInitializer: Quartz Scheduler successful shutdown.
    My native language is russian, so some messages are in this language.
    I think all errors arised at initialisation stage. And later, when i trying to press printing link, no new errors was appeared.

  • Tomcat/Cocoon/APEX PDF printing. Another issue

    Hi All,
    I am trying to implement my own custom report layout for the following simple Report query
    select e.DEPTNO, d.DNAME, d.LOC, e.ENAME, e.JOB
    from emp e, dept d
    where e.deptno = d.deptno
    The steps are the following
    1. Create Report Query
    2. Download XML file
    3. Use Stylus Studio to create XSL-FO (XSLT 2.0) based on XML data downloaded in
    previous step.
    4. Go back to Report query and upload XSL-FO file to APEX (layout name 'MyLayout' is also specified).
    Finish Report Query creation
    5. Enter Report Query again, select report layout 'MyLayout' and select Test Report
    The result is a failure with some java cocoon exception:
    org.apache.cocoon.ProcessingException: Unknown request object encountered named template : null
    Cocoon stacktrace[hide]
    Exception in StreamGenerator.generate() context://fop_post/sitemap.xmap - 17:32 <map:serialize type="xml">
    context://fop_post/sitemap.xmap - 13:33 <map:generate type="stream">
    Unable to get transformer handler for cocoon://fop_post/xsl context://fop_post/sitemap.xmap - 38:37 <map:serialize type="fo2pdf">
    context://fop_post/sitemap.xmap - 31:39 <map:transform>
    context://fop_post/sitemap.xmap - 30:38 <map:generate>
    context://sitemap.xmap - 1034:92 <map:mount>
    It seems to me that XSL-FO that I created for this layout is rejected somehow by APEX and not passed to Coccon at all.
    Guys, what am I doing wrong ? I will appreciate any help.
    Regards,
    Vadim

    Hi Mike,
    My standard printing is working nicely. That's the custom reporting that I experience problems with.
    After 8 hours of googling and 4 cups of coffee I figured out where the problem was. When you define XSL-FO file you need to 'escape' every occurence of % sign. For example you cannot define width= "100%" because APEX will pass this unchanged to Tomcat and Tomcat in turn will reject this but still passing NULL template pointer to Cocoon. Taking into consideration very poor logging capabilities one can spend hours trying to fugure out what is hapenning. APEX should be smart enough to escape characters or at least there should be a doco somewhere listing the rules you need to follow whem creating FO stylesheets.
    I must admit that the whole APEX PDF printing using Tomcat/Cocoon (and probably Fop because that's what used by Cocoon behind the scene anyway) is unfortunately a hack. Reporting does not have to be that complex.
    I would be extremely grateful if somebody can tell me what sort of XML tool is best suited to generate XSL-FO files that can be easily understood by APEX/Tomcat/Cocoon.
    Regards,
    Vadim

  • PDF Printing

    Hello:
    I'm running 11g. I'm trying to print to a PDF and I'm not having difficulty. In my application, when I click the Print link and try to open the PDF file, I receive the following error message:
    Adobe Reader could not open 'My_Orders.pdf' because it is either not a supported file type or because the file has been damaged (for example, it was sent as an email attachment and wasn't correctly decoded).
    I saved the .PDF and using EditPlus I opened the file and the following is shown within the file:
    report error:
    ORA-29273: HTTP request failed
    ORA-06512: at "SYS.UTL_HTTP", line 1186
    ORA-12570: TNS:packet reader failure
    I was able to successfully install BI Publisher. In my browser, I type the URL: http://HELEN:9704/xmlpserver and I am able to login as the Administrator user.
    I also upgraded APEX from 3.0 to 3.2 successfully. All the users who should be unlocked are unlocked.
    I enabled network services by running the DBMS_NETWORK_ACL_ADMIN proc. I ran the following query to verify that the grants were given:
    SELECT * FROM DBA_NETWORK_ACL_PRIVILEGES;The result of this query is the following:
    ACL                             ACLID                                   PRINCIPAL       PRIVILEGE  IS_GRANT  INVERT     START_D   END_DATE
    /sys/acls/power_users.xml     BD019FE78CAE40F3942C6A931378FA40     APEX_030200     connect     true     false     (null)     (null)In APEX, I logged in as ADMIN into apex/apex_admin and went to Instance Settings and did the following:
    - Oracle BI Publisher: Advanced Support
    - Print Server Protocol: HTTP
    - Print Server Host Address: HELEN
    - Print Server Port: 9704
    - Print Server Script: /xmlpserver/convert
    In my APEX application, in the Regions section, I click on the Print link next to my report. I have the following settings:
    - Enable Report Printing: Yes
    - Link Label: Print
    - Response Header: Report Settings
    - View File As: Attachment
    - Output Format: PDF
    - Report Layout: Default Report Layout
    - Print URL: f?p=&APP_ID.:4:&SESSION.:FLOW_XMLP_OUTPUT_R301336745008961227
    I think I covered everything I could to enable PDF Printing with APEX. I don't understand why I'm receiving the Adobe error and the errors found within the PDF file that I mentioned above.
    Can someone help me out?
    Thanks

    Hi Judyanne88,
    If you are printing the PDF files from the Adobe Reader program, reinstalling that program from the Adobe website may resolve the issue you are experiencing.  If you reinstall the program and still are unable to see the current view, please call or email us using one of the methods on the Contact Us page for further assistance.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • 8.2.4 Acrobat update cause print failure

    Once 8.2.4 update installed on Vista Enterprise PDF printing no longer works.   All applications error out.  Ran the Adobe fix command and rebooted.  Printing still fails.
    Is there an easy way to roll back to the previous version? 
    Are there any plans by Adobe to quickly release another patch? 
    Any other ideas on how to correct?

    ssieg_goblue wrote:
    we are receiving an Access Denied on our Windows XP machines when printing to the Adobe PDF printer sub system since this update... our Acrobat 8 plug-in for Office2007 is working fine though... Anyone else with similar behavior?
    On my Vista system even the Office2007 plug-in fails with similar print driver failures.   I have even tried running Microsoft Word 2007 as administrator without success.

  • General printer failure 8315:5218

    Hi,
    When one of the user is trying to print from Adobe pageMaker 7.01a, it does not print and gives the below error message
    An error occured while printing
    General printer failure
    8315:5218
    It works fine when try to use the same printer from other applications like Word etc. Reinstalling also did not help.
    Can somebody please help with this issue?
    Thank You

    Tried below things on users system. But no success.
    Print the same file to a different printer
    Copied the same file to a local folder and sent to print
    Created a new file and sent to print it to different printers
    Also ran Repair installation
    But none of this worked. The PageMaker does not print to any printer. And gives the same error
    Although I installed Acrobat on the system and can print it using Adobe PDF printer to a PDF file.
    Is it a PS printer? No
    Are you printing to FILE: ?
              I do not know how FILE: is related to this. But I opened "Printers and Faxes" window. Select File --> Server Properties. In the "Ports" tab could see an entry for FILE: Do not know how it is related with Adobe Pagemaker
    Are you using the Export… AdobePDF… macro? No
    Create a new PM publication, with just a square of black on it - does that print OK? No, it gives the same error
    It could be a permissions issue - are all the files on a local drive, usually C:, and not a server or flash drive? I copied file on local folder as c:\data\. But still the same error message.
    What if you remove all the images- does it print OK? I created a new publication with only text in it and tried printing it. But same message.
    Are you using any non-standard fonts? No
    I will also carry out a diagnostic recomposition as per your reply and follow instructions from troubleshooting page. Will update again if it worked or not.

  • Pdf printer driver install win 8.1

    i have uninstalled and reinstalled reader 11 5 times, that is after installing reader 8.1 in cs3. i have searched and tried every option and spent 5 hrs trying to get the pdf printer installed on my new asus with win 8.1. i was able to down load pdf blue and it worded out of the box. but why should i pay another $50 when i already pay adoby for the reader.  can any one help me with the fix?

    I have read your post several times, but I cannot figure out what your problem is; can you rephrase it?
    Also this part does not make any sense to me
    cy0179 wrote:
    why should i pay another $50 when i already pay adoby for the reader.

  • Save As Dialog not responding - PDF Printer

    Whenever I try and print to the PDF printer, (If preferences are set to prompt for file name) the "Save As " dialog locks up. The only way to clear this is to stop the Acrotray.exe. process.
    I have tried changing the printer preferences, but the only options that I can get to work are:
    Prompt for Adobe PDF filename
    Documents\*.pdf
    I I use the browse to point to a different location, when I save the setting, exit and then go back to check it, it has reset to Prompt.
    System
    Windows 7 Ultimate
    Adobe Acrobat Pro 9.3

    to make things clearer a screenshot of the dialog I'm talking about. this happens everywhere such a generic save file dialog appears.

  • Adobe PDF Printer not working as print driver; 9.5.5 (pro) with Windows 7, 64 bit

    I have installed, repaired, uninstalled and re-installed Acrobat Pro 9.5.5 on a newly formatted SSD with Windows 7, 64 bit on my desktop machine. The program was installed from Acrobat Pro 9.0.0 and updated within the program. I have the program also installed on my laptop, and the Adobe PDF Printer driver is working properly on my laptop.
    On my desktop with the newly formatted SSD, the Adobe PDF printer driver is not working. Note that I am using the printer driver, and not any pdf creation techniques within MS Office or other programs.
    When I go to the Adobe PDF printing preferences on my desktop, I only get a generic, two tab window open. When I print a file to this printer on my desktop machine, I do not get a window opening that asks where to create the pdf or what to name it, and I never see any files created. In MS Word, the Create PDF option under the Acrobat tab works and opens a dialog to ask the name and location to save, and then opens a PDF Maker progress window and properly creates the file. I can also save a file as an .eps or .ps file and use Distiller to create the pdf. However I cannot get the Adobe PDF printer driver in my Devices and Printers to work properly, although it works just fine on my laptop with the same program (Pro 9.5.5) and same Windows version (7, 64 bit).
    Repairing, uninstalling and re-installing does not solve the problem. Acrotray.exe *32 process is running. Any ideas on why this won't run properly on my desktop, but will run on a similarly configured laptop?
    On my laptop, I get a full, (7) tabl menu with all the normal options:

    I found this answer from Deepak Chauhan on another forum, and it solved this problem!
    Try this to add Adobe PDF printer manually on Windows 7, and Windows Vista.
    If windows 7 is Enterprise or better edition: (Admin rights required)
    Start>search for printmanagement.msc and open the print management module
    Expand the print server and expand the computer name to see availbale printers, drivers and printer ports.
    - from printers ensure there's no Adobe PDF printer, if there is delete it
    - go to ports and delete the PDF ports (the ones ending in *.pdf)
    - go to drivers and delete the PDF converter.
    Take note if any errors occur, but continue with the following steps regardless.
    If on windows 7 home edition, just goto start>Devices and Printers and ensure PDF pritner is not listed.
    Then open the registry (if any erors deleting these keys happen, see below)
    1: go to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Print\Printers
    delete any adobe PDF printer subkey present
    2: go to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors
    delee the PDF port monitor if present
    3: go to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers
    again delete and pdf printer subkey
    If any erros occur, you need to set the owner of the key to the currently logged in admin user, then ensure that user has full control.
    Do this by right-click the key and selecting permissions, clicking on advanced, then the owner tab.
    Once you've all that has been done, open a command line as administrator.
    Copy and pate the following commands in order
    1: net stop spooler
    2: rundll32.exe setupapi.dll,InstallHinfSection AdobePDFPortMonitor 128 C:\Program Files (x86)\Adobe\Acrobat 9.0\Acrobat\Xtras\AdobePDF\AdobePDF.inf
    3: net start spooler
    4:rundll32.exe printui.dll,PrintUIEntry /if /b "Adobe PDF" /f "C:\Program Files (x86)\Adobe\Acrobat 9.0\Acrobat\Xtras\AdobePDF\AdobePDF.inf" /r "Documents\*.pdf" /m "Adobe PDF Converter"
    That should set back the pdf printer.
    This seemed to provide the link that provided the Adobe PDF Settings tab to the Adobe PDF Printing Preferences that was missing!

  • Photosmart 7510 e all in one series Printer failure Oxc19a0023

    After having been turned off for several months, I plugged in my 7510e and the following message came on the screen.
    Printer failure, Oxc19a0023, Please turn printer off then on. I did this with no change. I unplugged both electric plus and USB and reconnected. I removed the cartridges and replaced but the same message keeps coming and I cannot get passed this message. If anyone has had this problem and has been able to fix this or if anyone know how to fix this I would really appreciate some help. Thank you.

    Hello @TSLI76 , and welcome to the HP Forums, I hope you enjoy your experience!
    I see you are experiencing 0x errors.  I would like to help!
    I would recommend removing the ink cartridges, and performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
    I would also recommend this document on An 'Ink System Failure' or a '0x ...' Error Message Displays on the HP Printer Control Panel.
    Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
    Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
    Jamieson
    I work on behalf of HP
    "Remember, I'm pulling for you, we're all in this together!" - Red Green.

  • Using PDF Printer TO Print Multiple Word Docs At Once.

    I Have Just upgraded from acrobat to acrobat 3d. In Acrobat 5 i was able to select a batch of word document (150+ usually) and use the send to command to send them to the acrobat distiller and each document would open one at a time print and then close. I have now been upgraded to Acroabat 3D and if i use the same Send to Command to send a batch of word docs to the pdf printer it tries to open all the selected files at once and i get an error message "the command cannot be performened because a dialog box is open..." this is because the 1st document is open and printing so the secound document that opened at the same time cannot operate the print command. Can Anyone help?

    Thanks for the suggestion but...
    1. I can't get these scripts to run in 10.4.8
    What if you save the script as a stand alone app? Does that make a difference?
    2. I haven't spent much timr trying since it looks
    like thy only convert "JPEG", "GIFf", "PICT", "TIFF",
    "PDF" & "TEXT". Am I wrong?
    That's what it looks like from the "extension-list" - what type of files are you trying to convert?

  • PDF printer has a problem with Safari in "Reader" mode in Windows7

    As shown in the image above. When I try to use the PDF printer to print out a web page in Safari "Reader" mode, the lines near the bottom of each page get squeezed like this. There is no problem with XPS printer. I guess this problem is because of some incorrect settings in Safari or the PDF printer?
    My system is Windows 7 Pro. I am using Acrobat X Pro. The page I am trying to print is http://en.wikipedia.org/wiki/Electronic_band_structure. This problem only happens when the webpage is adjusted into "Reader" mode in Safari.

    Many thanks for your reply!
    I am sorry, I did not make my question clear. I would like to save some web pages only in "Reader" mode, because in this mode all the advertisements are filtered out and the pages look much nicer than the origional layout.
    I first let Safari to active "Reader" by clicking "Reader" button.
    Then I click "Print" button and select Adobe PDF as the printer.
    The problem is the PDF file has something wrong (shown above), and I would like to know how to avoid this problem.

  • PDF Printer and Acrobat fail to open or run or anything else.

    Hi
    Adobe Acrobat Standard 9 has been installed on this TS2008 (VM) server for over a year without problem until recently.
    To start, the Adobe PDF printer stopped creating PDFs. When it worked a user would print and the PDF (creation) progress bar dialog box would open and the Adobe Distiller icon would appear in the taskbar (swirling) and a PDF would be created. Now we get the progress bar but no Distiller icon and no PDF is created.
    Then Adobe Acrobat Standard (editor) failed to open any PDFs. We installed Adobe Acrobat 9 reader which opened PDFs for a while and now that has stopped working.
    After many uninstalls, reinstalls, reg cleans we decided to open a case with Adobe who told us that Acrobat 9 is not supported on Server2008. The customer purchased Adobe Acrobat X.
    We installed Acrobat X (in terminal server mode) and all was well for around 24hrs and then it all stopped working again.
    I have since uninstalled reinstalled again. I created 1 PDF and after that the progress bar just hangs. We performed a controlled user logon to the server and all was going well until one user logged in and he isnt able to open Acrobat to read or edit PDFs.
    There are no events logs which appear to directly relate to this. We were concerned about a HpBIDI driver which no longer errors but we do have a large amount of EventID 7036, ServerControl Manager Eventlog provider and EventID 4 SpoolerWin32SPL.
    We have since been back to Adobe Support who advised us to unplug the network cable which we cannot do as its a hosted VM (with no access to the the VM console). He then asked us to remove the server from the Domain which we can't do as this is a single live server. They intend to come back to me!
    We are really at a loss here for idea's, can anyone please provide some clues?
    Thanks

    Hi billu54860732,
    Try running the Repair command from under the Help menu to see if it corrects the problem.
    The probable cause of the error is, multiple processes of Acrobat/Reader running in the background.
    If 'Repair' doesn't resolve the issue kindly follow the steps mentioned below and check, if it helps.
    1) Press CTRL+ALT+DEL together
    2) Go to the Task Manager
    3) Go to Processes in the Task Manager and kill al the processes related to Acrobat/Reader.
    4) Launch Reader/Acrobat (It should launch without an error).
    To further isolate the issue you might want to run Acrobat/Reader in an environment where no other services are running.
    This can be achieved via "MSCONFIG"
    1) Click on start type run
    2) Type MSCONFIG in the run prompt
    3) Go to services and click on hide all Microsoft services
    4) Click disable all
    5) Go to the startup in configuration window and disable all startup items
    6) Restart your system
    7) Launch Acrobat/Reader
    If, it is launched without an error, a service on your system is conflicting with Acrobat/Reader.
    Let me know if issue persist.
    Regards,
    Aadesh

  • PDF printer

    Hi All,
    Kindly help me answering the following questions.
    1) Please give me the guidelines on testing and how we can test the layouts and forms that are being
        developed using PDF printer.
    2) Why we want to test using PDF print ?
    Regards!

    got the answer

Maybe you are looking for

  • I need to move my apps, etc from one computer to another but I can't? Help!

    I recently upgraded my phone from an iphone 3gs to and iphone 4s. At the same time I thought it was the right time to move my itunes from my old laptop (which has no wireless) to a new laptop with wireless so it would be easier to up and download mus

  • Random Delete tool with Scriptographer

    Hi, I am trying to refine the RandomTools created for Scriptographer so that it suits my preference, but I can't figure it out in Javascript. Not knowing a lot of Javascript don't help me either! Here is the script, simplified to conserv only the Del

  • 4.0.1 crashes now when you double click a file to edit in source monitor

    If I double click a file to watch it in Media Browser or in the project window premiere crashes. In fact the only way I can open a source window to set in and out points is if the clip is in the timeline. This makes editing with premiere almost unusa

  • Drag and Drop to matching area

    I have am image that has been sliced and each slice has been made into a movie clip and put into an selectImage: array. I have matching movie clips also put into a (parell) matchImage:array. I am trying to drag each movieclip onto it's matching movie

  • Azure to Azure Migration Cloning between subscriptions

    What is the best way to clone a configuration of VMs (Biztalk, SQL, 2012 Server, etc..) from one subscription to another? Is it possible to build a shell configuration of VMs in a Virtual Network and clone it to another subscription?   So this is not